Double-sided sanding block, belt sander; lubricating gel block with belt sanding arm

ACETI 29

Condition: new, ACETI adjustable belt sander art. 17 Volt 400 - Three-phase Electric absorption : Kw 1.1 Crb2I0Sgqy Rpm 2800 Belt width mm 120 Belt development mm 1500 Weight kg 75

Condition: excellent (used), Year of construction: 2000, tube diameter 20 - 70 mm grinding band dimension 75 x 2000 mm Band Speed 30 mm/sec. motor speed 1400/2800 U/min power capacity 3 kW gear diameter 200 mm Dust suction hood 80 mm weight 125 kg range L-W-H 0,65 x 1,5 x 1 m Pipe grinding machine - little used - for small pipe diameters and balcony railings. Pipes with diameters from Ø 20 mm to Ø 70 mm can be processed with this. Angle of the pipe grinder 90° to 30°. The machine is also very suitable for stainless steel pipes thanks to the pole-changing motor and halved speed. Suitable for grinding steel and stainless steel pipes For round and square tubes adjustable depth stop very durable, robust execution precise delivery. Available rollers with diameters of 10, 18, 23, 28, 30 and 42 mm. - Angle of attack of the vice can be adjusted according to the scale - Quick clamping system for the pipe to be processed as well as the positioning of the vice - Feed takes place via a handwheel - Suitable for pipes with any wall and solid material - For round and square tubes - Depth stop for reproducible results - Balanced aluminum drive roller - Belt tension via spindle drive - Belt run can be adjusted using an adjusting screw - Changing the belt by swinging away or dismantling the spark boxes - Support table on the sanding surface 75 x 400 mm - Graphite coated grinding surface for deburring work - Spark drawer under the sanding roller - Spark box with extraction nozzle in the rear area of the machine - Extremely powerful motor for heavy use Clakpeyzpk - Powerful and low-vibration three-phase motor - Motor suitable for continuous operation - Large bearings guarantee smooth running with low noise - Stable base cabinet on four rubberized feet. Machine dealer with own stock of 1600 m².

Condition: good (used), Aceti Macchine double grinding wheel Type: FB 90 2/4 ART 101 Diameter grinding stone max: 210 mm 7Kjzavhv9M Machine height: 130 cm Weight: ca 125 KG

Condition: excellent (used), Functionality: fully functional, The following item is for sale: - Our offer number: 29/130 - Paper cutter Paper cutter up to A 4 - Manufacturer: HSM - Type: T 3206 - Dimensions: WxDxH 210x430x60 mm - weight: 1 kg - optical condition according to photos - Used very well maintained Bavnsgz7Z - functional - Shipping Germany-wide 8,90€ Notes: The goods offered here usually come from company liquidations and insolvencies. Due to missing type plates, it is not always possible to provide exact item data. The item pictures are original photos that show the actual condition of the item. If several identical items are offered, only one of the items will be photographed. There may be slight variations in the condition of the individual items. If an item is opened or repaired/rebuilt by the buyer, any warranty claim will be void. This also applies if repairs and modifications are carried out by third parties without prior agreement. Company names and trademarks used are the property of their owners. They serve exclusively to identify and describe the goods.

Condition: new, Year of construction: 2024, Functionality: fully functional, Available immediately!!! Various sizes and machine combinations available! Contact us - we will be happy to advise you! The perfect solution for universal applications in metalworking industrial companies and metalworking shops. Free-standing universal belt grinder For processing flat grinding surfaces and contact rollers Belt dimensions: 120 x 1500 mm Three-phase motor: 400 V 1.1 kW Speed range: 2800 rpm Cutting speeds: 20 m/s Grinding table: 120 x 450 mm Contact roller: Ø135 mm Suction nozzle: Ø80 mm Rubberized, spiral-grooved and balanced contact roller made of aluminium Belt tension via spindle drive Belt run adjustable via guide roller Belt change by swiveling off or removing the spark boxes Grinding arm can be clamped steplessly between 0 - 90 Support table can be mounted on the surface grinding area and contact roller Spark box can be adjusted and removed from the surface grinding area and contact roller Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise levels Sturdy base cabinet on four rubberized feet Hu0Qlrc Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pin IP 44 red) German operating instructions and CE declaration of conformity Sanding belt in zirconia alumina quality Optionally available: 2nd speed Extraction unit installed in the base cabinet

Year of construction: 2021, operating hours: 5 h, Condition: as good as new (ex-display), machine/vehicle number: 6178, Exhibition machine: ACETI ART.70 Belt grinding and polishing machine with 2 motors 4.4 kW, 400 volts including 2 inverters T2 The machine is in our test room in Kobenz. Machine is new and has not run! GRINDING UNIT (left) - Sanding belt dimensions: 50 x 2500 - 3000 mm - Drive roller: 50 x ø 250 mm - Belt grinding arm: 0° - 90° - Belt speed: 18 - 36 m/sec POLISHING UNIT (right) - for grinding and polishing wheels: 300 x 35 mm - Brush maximum external size: 300 mm - Brush maximum width: 75 mm - Motor shaft diameter: ø 35 mm - Circumferential speed: 22 - 44 m/sec Size: W: 1650 x D: 600 x H: 2200 mm Volume: 73dB Weight: 295kg (without inverter) Ckkpmurxto

Condition: good (used), Aceti telescopic belt sander with pivoting belt, 2.2kW 400V Double speed Weight Kg 110 Belt width mm 50 Hp 2.5. - Kw 1.8 The Aceti ART.28 belt sander is a professional machine ideal for performing sanding, grinding and finish deburring on all types of metal materials. Equipped with an arm that can be swiveled from 0° to 90°, the elements can be placed on the workpiece support surface to perform squaring operations or directly on the abrasive belt for smoothing operations. The rubberized, grooved and balanced drive wheel provides better abrasive belt drag. The sander features a sturdy base mounted on anti-vibration feet that minimize vibration levels. Powered by a powerful 2.2 to 1.3 kW 3-phase 2-speed electric motor capable of generating a speed of 2800 to 1400 rpm. Itk77Ml

Condition: excellent (used), Year of construction: 2016, Functionality: fully functional, BELT GRINDING Dnan2V

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! For chamfering, deburring and grinding of visible surfaces Features and design of the belt grinding machine: For machining on plane grinding surface and contact roller. Belt dimension: 120 x 1500 mm Cutting speed: 10 / 20 m/s grinding table: 120 x 470 mm contact roller: Ø135 mm suction nozzle: Ø60 mm Rubberized, spiral grooved and balanced contact roll made of aluminum Tensioning of the belt via spindle drive Belt run adjustable via guide roller Strip change by swinging off or dismantling the sparking boxes Support table mountable on surface grinding and contact roller Grinding arm steplessly clampable between 0 - 90 Spark box adjustable and demountable on surface grinding and contact roller Features and design of the disc grinding machine: For precise surface grinding grinding disc: Ø400 mm Cutting speeds: 30 / 60 m/s Support table: 450 x 230 mm Angle of support table: 0 - 90 Suction nozzle: Ø80 mm For the use of Velcro as well as self-adhesive abrasive sheets Variable cutting speeds for desired material removal, surface quality and temperature effect on the component Support table height adjustable Adjustable angle of the support table Balanced clamping plate made of aluminum Spark box with exhaust port Design as free-standing machine Three-phase motor: 400 V 1.8 kW Speed: 1400 / 2800 rpm Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Ft9Tuk2 Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions as well as CE declaration of conformity Sanding belt and sanding sheet in zircon corundum quality Optionally available: Extraction unit - IA-2: Built into the base cabinet, incl. automatic switch-on, filter bag, quick-action clamp and aluminum spiral hose.

Year of construction: 2003, Condition: as good as new (ex-display), Exhibition machine: ACETI AC 02 Stationary edge milling and belt sanding machine Sanding belt: 120x1500mm Machine is in our showroom in Kobenz. Machine is as good as new and not run! Power: 1,8 KW Weight: 120 KG Size: 700 x 600 x H. 1600 mm Data grinding unit: Contact rollers: 135 mm diameter Cutting speed: 10 - 20 m/sec dimensions of working surface: 120 x 470 mm Data edge milling unit: Chamfer angle: 15° - 45° cutter diameter: 80 mm Qawvxf dimensions of the support: 100 x 500 mm

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! For machining on the contact roller Features of the Aceti contact belt grinding machine ART. 28: Freestanding contact belt grinder belt dimension: 50 x 2000 - 2500 mm three-phase motor: 400 V 1,8 kW Speed ranges: 1400 / 2800 rpm cutting speeds: 15 / 30 m/s contact roller: Ø200 mm suction nozzle: Ø80 mm Free standing and unobstructed contact roll Suitable for abrasive and non-woven abrasive belts Graphite coated grinding surface Rubberized, spiral grooved and balanced contact roller made of aluminum Belt tension via spindle drive Belt run adjustable via guide roller Belt change by swinging off the spark boxes Grinding arm steplessly clampable between 0 - 90 Spark box on contact roller adjustable and removable Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Main switch lockable Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions as well as CE declaration of conformity Sanding belt in zircon corundum quality Enh0Xaj Optionally available: Extraction unit - IA-1: Built into the base cabinet, incl. automatic switch-on, filter bag, quick-action clamp and aluminum spiral hose.

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! Machining of containers, boxes and welded constructions, especially the grinding of welded edges, visible surfaces and corners are among the common applications on our Aceti long belt grinding machines. For grinding and satin finishing For machining visible surfaces On containers, boxes and welded structures Welded edges and corners For machining compact and light components Features of the Aceti long belt grinding machine ART. 143: For surface machining with the sanding pad as well as the sanding roller Suitable for abrasive and non-woven belts Belt dimension: 120 x 4000 mm Three-phase motor: 400 V 1,5 kW Speed: 1400 / 2800 rpm Cutting speed: 11 / 22 m/s grinding table: 1500 x 550 mm max. workpiece dimensions: 1500 x 550 x 560 mm max. workpiece weight: 50 Kg suction nozzle: Ø120 mm Cvmcbmqufd Extremely compact design - unique construction grinding table suspended on a column - space-saving and easy to move The surface of the grinding table is covered with PVC strips Grinding table is electrically adjustable in height and can be guided by hand Belt drive via aluminum contact roller Belt tension via spindle drive Belt run adjustable via guide roller Quick belt change by swinging off the spark boxes Grinding shoe spring-loaded and coated with graphite Stop angle for component positioning Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable machine frame on three rubberized feet Scope of delivery: Sanding belt in zircon corundum quality High-quality tool set and wall plug German operating instructions and CE declaration of conformity Optionally available with inverter for infinitely variable speed control

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! For deburring sawn components or for chamfering visible and welded edges For the processing of medium sized and precise components Cdseps9W Features of the Aceti edge milling machine ART. 03: Freestanding machine version Three-phase motor: 400 V 1,5 kW Speed: 2800 rpm Cutting speed: 12 m/s chamfer width: up to 4,2 mm Bevel angle: 15 - 45 Cutter head: Ø80 mm Indexable inserts: 10 pieces ISO SPUN 12.03.08 Prism: 500 x 80 x 100 mm The cutter head mills on the circumference which prevents the formation of a grade The prism can be positioned axially over the cutter head so that the inserts can be used over the full width. The indexable inserts can be rotated - thus all four sides can be completely utilized Chamfer width adjustable by means of handwheel and scale Prism hardened and swiveling Prism runs flush together - no slipping through of flat sheets By using different inserts almost all materials can be machined Cast iron prism bed minimizes vibrations Attention: Mill only in up-cut mode! Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions as well as CE declaration of conformity Cutter head equipped with carbide inserts

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! Processing of straight and bent tubes as well as round material For grinding and satin finishing Suitable for abrasive and fleece belts Features of the Aceti pipe grinder ART. 150: Tube diameter: 5 - 120 mm belt dimension: 2x 60 x 900 mm three-phase motor planetary wheel: 400 V 1,85 kW speed: 1400 rpm three-phase motor grinding unit: 400 V 3 kW speed ranges: 1400 / 2800 rpm cutting speeds: 10 / 20 m/s Suction nozzle: Ø80 mm Two belts rotate around their own axis on the planetary wheel Foot switch for belt opening ensures safe insertion of the workpiece Belt drive by rubberized and spiral grooved aluminum contact roller Tensioning of the belt by spring Fast belt change Self centering belt Band change by swinging off the protective hood Protective hood with contact switch Powerful and low-vibration three-phase motors Motors suitable for continuous operation Dqv2Xayfi Stable base cabinet on four rubberized feet Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pin IP 44 red). German operating instructions as well as CE declaration of conformity Abrasive belts in zircon corundum quality

Condition: new, Immediately available!! Different sizes available! Contact us - we will be happy to advise you! For surface grinding and satin work on flat components Subsequent processing of bending, spot welding, or cutting work, etc. For the production of visible surfaces Deburrs and rounds edges and openings Features of the Aceti continuous belt sander ART. 76 Free standing continuous belt sander Suitable for abrasive and non-woven belts Belt dimension: 300 x 1900 mm Three-phase motor: 400 V 4,6 kW Speed range: 1500 rpm cutting speeds: 8 m/s infinitely variable belt feed: 1 - 10 m/min cooling lubricant unit 70 l with filter fleece installed in the base cabinet suction nozzle: Ø120 mm minimum length of the components: 140 mm Maximum height of the components: 205 mm Maximum width of the components: 300 mm A conveyor belt guides the components under the sanding belt Suitable for both wet and dry machining The use of cooling lubricant enables a better surface finish, lowers the temperature effect on the component, binds the grinding dust and provides corrosion protection Cvl9Ttnxy8 After machining, the water runs together in the collection tray, is fed back into the settling tank via a filter fleece mat and is cleaned in the process In addition, a filter cartridge cleans the cooling lubricant Cooling lubricant hose with pistol for cleaning the mechanical components as well as the catch basin If components are machined dry, the grinding dust can be extracted via an exhaust port. Hold-downs before and after the grinding roller provide additional hold on the conveyor belt The contact pressure of the rollers can be adjusted The rollers are rubberized and spring-loaded Hand wheel with scale for adjusting the material removal rate Constant belt tension and quick belt change via pneumatic cylinder Rubberized, spiral grooved and balanced contact roller made of aluminum Guide roller covered with Vulkollan Belt run is adjusted with the enclosed pin wrench with cross handle Belt change by opening the door Protective door with contact switch The cooling lubricant system can be switched on if required Nozzles wet the grinding belt with cooling lubricant The intensity of the cooling lubricant can be adjusted by a tap Compressed air nozzles remove grinding dust and cooling lubricant from the conveyor belt, thus increasing the adhesion of the components on the conveyor belt Contact protection at the inlet of the machine with emergency stop function Compressed air maintenance unit included Extremely powerful motor for heavy duty use Powerful and low-vibration three-phase motor Motor suitable for continuous operation Electric motor with mechanical brake for quick machine stop Large bearings guarantee smooth running with low noise level Main switch lockable Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions and CE declaration of conformity Abrasive belt in zircon corundum quality Cooling lubricant Filter fleece roll

Condition: new, Immediately available!! Different sizes and machine combinations available! Cvgmqt03Ia Contact us - we will be happy to advise you! For chamfering, deburring and grinding As well as for machining hard components and tools For machining small and precise components Features of the Aceti double grinding machine ART. 107 Designed as a free standing machine Sometimes used for grinding and pointing drills, deburring hard components and resharpening tools For machining on the circumference of the grinding wheel Wheel dimensions: Ø300 x 35 x Ø30 mm three-phase motor: 400 V 1,8 kW Speed: 1400 rpm Cutting speed: 22 m/s suction nozzle: Ø80 mm High running smoothness and low noise level of only 69 dB Massive and adjustable support table Robust spark box with exhaust port Water box for cooling heat-sensitive components between machining operations Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions as well as CE declaration of conformity Delivery incl. grinding wheels Optionally available: Extraction - IA-2: Built into the base cabinet, incl. automatic switch-on, filter bag, quick-action clamp and aluminum spiral hose. Inverter: For infinitely variable speed control 300 - 3000 rpm.

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! Components can be polished, ground, deburred and brushed Features of the Aceti polishing machine ART. 66: Freestanding machine Three-phase motor: 400 V 1,8 kW Speed: 1400 / 2800 rpm Wheel dimension: Ø250 x Ø25 mm Max. wheel width: 70 mm Hmtsi2R Cutting speed: 18 / 36 m/s High running smoothness and low noise level of only 70 dB Suction nozzle: Ø80 mm For polishing discs, felt discs, cord brushes, sisal brushes, abrasive fleece discs, flap discs, wire brushes, plastic brushes, etc. Machine mandrel for universal mounting of brushes and discs As well as quick disc change without the disassembly of the hood possible Powerful and low-vibration three-phase motor Motor suitable for continuous operation Protective hoods with exhaust Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions as well as CE declaration of conformity Delivery without polishing wheel Optionally available: Extraction - IA-1: Built into the base cabinet, incl. automatic switch-on, filter bag, quick-action clamp and aluminum spiral hose. Inverter: For infinitely variable speed control 300 - 3000 rpm.

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! Components can be polished, ground, deburred and brushed Features of the Aceti polishing machine ART 27: Freestanding machine Three-phase motor: 400 V 1,8 kW Speed: 1400 / 2800 rpm Wheel dimensions: 2x Ø250 x Ø25 mm Max. wheel width: 70 mm Cutting speed: 18 / 36 m/s High running smoothness and low noise level of only 70 dB Suction nozzle: Ø80 mm For polishing discs, felt discs, cord brushes, sisal brushes, abrasive fleece discs, flap discs, wire brushes, plastic brushes, etc. Machine mandrel for universal mounting of brushes and discs Two-armed version for pre- and finish polishing or for different discs As well as quick disc change without the disassembly of the hood possible Powerful and low-vibration three-phase motor Motor suitable for continuous operation Protective hoods with exhaust Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions as well as CE declaration of conformity Delivery without polishing wheels Spb2F Optionally available: Extraction - IA-2: Built into the base cabinet, incl. automatic switch-on, filter bag, quick-action clamp and aluminum spiral hose. Inverter: For infinitely variable speed control 300 - 3000 rpm.

Condition: new, Immediately available!! Different sizes available! Contact us - we will be happy to advise you! For the processing of particularly large and massive components Features of the Aceti belt grinder ART. 64: Freestanding belt grinder For machining on face grinding surface and contact roller Particularly large surface grinding area Belt dimension: 300 x 2500 mm Three-phase motor: 400 V 4,5 kW Speed ranges: 1400 / 2800 rpm Cutting speeds: 15 / 30 m/s grinding table: 300 x 900 mm contact roller: Ø200 mm suction nozzle: 2 x Ø80 mm Rubberized, spiral grooved and balanced contact roller made of aluminum Tensioning of the belt via spindle drive Belt run adjustable via guide roller Vulkollan coated guide roller Strip change by swinging off or dismantling the spark boxes Particularly stable support table at the surface grinding area - can be dismantled Particularly stable support table at the contact roller Spark box on face grinding surface and contact roller can be adjusted and dismantled The spark box on the contact roller is equipped with an additional suction nozzle Suction socket in the machine frame under the contact roller Extremely powerful motor for heavy duty use Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Befzup7M Torsion-resistant and solid base construction on rubberized feet Main switch lockable Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5 pole IP 44 red). German operating instructions as well as CE declaration of conformity Abrasive belt in zircon corundum quality Optionally available: Extraction: Aceti extraction system cyclone separator ASP. 01 HP2 Scotch-Kit: Adapted spark boxes and support tables for the use of non-woven abrasive belts. Abrasive fleece is particularly suitable for satin finishing and deburring of profiles. Inverter: For infinitely variable speed control 300 - 3000 rpm. Foot switch: For convenient switching on and off of the machine.

Condition: new, Immediately available!! Also available as a single-arm variant! Contact us - we will be happy to advise you! For end face deburring of tubes, profiles and bar stock By turning, the inner and outer burr can be removed in one operation For the processing of large and massive components Features of the Aceti brushing machine ART. 81: Free standing universal brushing machine For internal and external deburring of sawn tube ends, bar stock as well as profiles For machining on the circumference of the brush Dimension brush left: Ø250 x 60 x Ø100 mm dimension brush right: Ø250 x 120 x Ø100 mm Three-phase motor: 400 V 4,4 kW Speed range: 1400 / 2800 rpm Cutting speeds: 18 / 36 m/s For components up to 60 mm as well as 120 mm width / diameter Suction nozzle: Ø80 mm Solid support table with prism Support table is height adjustable As well as radially adjustable to the brush Sturdy spark box with protective screen and suction nozzle Extremely powerful motor for heavy duty use Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Main switch lockable Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) Eqhft7T German operating instructions as well as CE declaration of conformity Brushes for the processing of steel Optionally available: Extraction unit built into the base cabinet, incl. automatic switch-on, filter bag, quick-action clamp and aluminum spiral hose. Brush for stainless steel

Condition: new, Immediately available!! Different sizes available! Contact us - we will be happy to advise you! For face grinding of radii in infinitely variable angles For railing construction, pipe constructions etc. Features of the Aceti pipe grinder ART. 142: Freestanding universal pipe grinder For machining operations on the grinding roller as well as on the face grinding surface Belt dimension: 250 x 2500 mm For pipes Ø30 - 245 mm Miters up to 30 Max. Ø at angle of attack: Ø121 mm x 30°, Ø170 mm x 45°, Ø210 mm x 60°. Grinding roller: Ø5″ Three-phase motor: 400 V 6.5 kW Speed: 1400 rpm Cutting speeds: 18 m/s Grinding surface: 300 x 460 mm Drive roller: Ø250 mm suction nozzle: Ø80 mm Angle of the vice adjustable according to scale vice with spindle drive for clamping the pipe to be machined Vise can be rotated in both directions Solid vice mounted on a cross slide for even wear of the grinding belt Vise can be moved on the bed slide - saving time on steep miters as the slide does not need to be moved far Cve0Tz83Is Feed is made by a hand wheel Suitable for tubes in any wall as well as solid material For round and square tubes Depth stop for reproducible results Balanced and rubberized drive roller made of aluminum Belt tension via spindle drive Band run adjustable via set screw Belt change by swinging off or dismantling the spark boxes Support table at the grinding surface Graphite coated grinding surface for deburring work Spark drawer under the grinding roller Spark box with exhaust port at the rear of the machine Extremely powerful motor for heavy duty use Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions and CE declaration of conformity Sanding belt in zircon corundum quality Grinding roll as desired incl. ball bearing

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! Robust and durable disc grinding machine Free standing grinding machine grinding plate: Ø400 mm Three-phase motor: 400 V 1,8 kW Speed ranges: 1400 / 2800 rpm Cutting speeds: 30 / 60 m/s Support table: 450 x 230 mm Angle of support table: 0 - 90 suction nozzle: Ø80 mm Structure of the Aceti disc grinding machine ART. 24: For precise surface sanding For the use of Velcro as well as self-adhesive sanding sheets Variable cutting speeds for desired material removal, surface quality and temperature effect on the component Support table height adjustable Adjustable angle of the support table Balanced clamping plate made of aluminum Spark box with exhaust port Extremely powerful motor for heavy duty use Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Main switch lockable Cvenu80E7C Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions as well as CE declaration of conformity Sanding sheet in zircon corundum quality Optionally available: Extraction unit built into the base cabinet Inverter for continuously adjustable speed

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! The perfect solution for the workbench! Design as table machine For machining on plane grinding surface and contact roller belt dimension: 100 x 1000 mm three-phase motor: 400 V 1,1 kW speed: 2800 rpm Cutting speed: 15 m/s grinding table: 100 x 290 mm contact roller: Ø100 mm suction nozzle: Ø60 mm Structure of the Aceti belt grinder ART. 22: Rubberized, spiral grooved and balanced contact roller made of aluminum Belt tensioning by spindle drive Belt run adjustable via guide roller Belt change by swinging off or dismantling the spark boxes Grinding arm steplessly clampable between 0 - 90 Support table can be mounted on face grinding surface and contact roller Spark box can be adjusted and dismantled on face grinding surface and contact roller Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable table machine on four rubberized feet Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions as well as CE declaration of conformity Sanding belt in zircon corundum quality Cvd9Ytrasp Optionally available: 2nd speed 1400 and 2800 rpm

Condition: new, Immediately available!! Different sizes and machine combinations available! Contact us - we will be happy to advise you! The perfect solution for universal applications in metalworking industrial plants and locksmith's stores. Free standing universal belt grinding machine For machining on plane grinding surface and contact roller Belt dimension: 120 x 1500 mm Cvd9Th22J7 three-phase motor: 400 V 1,8 kW Speed ranges: 1400 / 2800 rpm cutting speeds: 10 / 20 m/s grinding table: 120 x 470 mm contact roller: Ø135 mm suction nozzle: Ø80 mm Rubberized, spiral grooved and balanced contact roller made of aluminum Tensioning of the belt via spindle drive Belt run adjustable via guide roller Belt change by swinging off or dismantling the spark boxes Grinding arm steplessly clampable between 0 - 90 Support table can be mounted on face grinding surface and contact roller Spark box can be adjusted and dismantled on face grinding surface and contact roller Powerful and low-vibration three-phase motor Motor suitable for continuous operation Large bearings guarantee smooth running with low noise level Stable base cabinet on four rubberized feet Main switch lockable Scope of delivery: High-quality tool set, cable and plug (CEE plug 16 A 5-pole IP 44 red) German operating instructions as well as CE declaration of conformity Sanding belt in zircon corundum quality Optionally available: Extraction unit built into the base cabinet Inverter for continuously adjustable speed

Condition: new, Available for immediate delivery!!! Different sizes available! Contact us - we will be happy to advise you! Free-standing extraction unit for steel dusts three-phase motor: 400 V 1,5 kW Speed: 2800 rpm Max. Air flow rate: 940 m³/h Suction port: Standard Ø120 mm, alternatively Ø80 mm Air outlet via three large pipes with filter fleece inserts Mobile: 2 swivel castors & 2 fixed castors Safety note: Not suitable for aluminum dust! Structure of the Aceti extraction system ASP. 01-HP2: The dust laden air is fed into the cyclone The air flow goes in a circle The heavy particles slide down the hopper and cool down in the process Cu9Tqmfjl2 A drawer in the lower part of the machine catches and collects them The exhaust air is additionally cleaned via filter fleece mats and fed back into the room Extraction system for large machines Large dust drawer Commercially available filter fleece mats Powerful and low-vibration three-phase motor Motor suitable for continuous operation Stable base on four rollers Scope of delivery: Cable and plug (CEE plug 16 A 5 pole IP 44 red) German operating instructions and CE declaration of conformity Filter flow mats Delivery without hose and clamps