Haul-off unit

Bernhard Ide GmbH & ME 30/6.1

Condition: new, Year of construction: 2025, Functionality: fully functional, machine/vehicle number: 30627, UP-STROKE SAW UNIT ME50/6.1 - New machine from the IDE stock programme - Type ME 50/6.1-U/6-400/500-K/PP - Base frame 1.5 metres long - Travelling saw carriage 500 mm, pneumatically supported - Pneumatic saw stroke - Profile passage according to sawing diagram D-50-6-1, for saw blade Ø 400 mm - Saw blade drive 1.5 kW - Saw blade speed frequency-controlled - Hold-down bridge, limit switch protected - 1 connection piece Ø125 mm for external chip external chip extraction system - Table cover with V2A slats - Protective panelling with hinged door, with limit switch protection (magnetic switch) * With inlet and outlet protection channel, 600 mm long - SPS control ME-Control 10/2 * Integrated operating unit with system and numeric/functional keypad * LCD display, monochrome, size 160 x 80 pixels Iiolhjwcaz Tjccqpjc * 10 preselectable programmes for entering: + part length in mm + number of pieces * Error message in plain text - Length encoder 24 V - 5000 imp/rev. incl. attachments for IDE caterpillar haul-off ME 31/2, ME 32/2 or ME 32/3 - incl. saw blade ø400 mm - without dust extraction

Year of construction: 2013, Condition: ready for operation (used), machine/vehicle number: 248, CALIBRATION UNIT ME16/6.2 Ijlsu Tgrvshccqpsic - used machine (IDE-Technikum), checked and ready for operation - mounting platform 3950mm x 700mm - motorized length adjustment 500mm - motorized height adjustment 875 - 1025mm - manuell cross adjustment, 50mm - 2 vacuum pumps - 2 manifold with each: * 20 water connections 1/2" * 20 vacuum connections 1/2"

Condition: used, Year of construction: 2004, Functionality: fully functional, machine/vehicle number: 756, PUNCHING UNIT ME 40/6.3 - Used machine, function-tested - Working principle pneumohydraulic - Travelling distance: 200 mm, pneumatically supported - Punching force 24 KN at 6 bar - Punching/power stroke: 50/12 mm (power pack S4.50.12D) - Punching sequence max. strokes/min.: 40 (depending on profile and speed) - End position monitoring by limit switch - Installation dimensions for punching tool: Ielhccqotx A Akjpjic (w x h x l) 180 x 138 x 225 mm - Protective panelling with hinged door, limit switch protected - Without inlet/outlet protection channel - For mounting a column guide frame 350x 250x 250 mm * without column guide frame - without punching tool - incl. sequence control for external punching release (24V signal, potential-free required)

Year of construction: 1996, Condition: used, Functionality: fully functional, machine/vehicle number: 465, HAUL-OFF UNIT ME 30/4 - used machine, function-tested - Driven by 2 GS motors 0.8 kW each - Pull-off speed 0.5 to 10 m/min - Pull-off force max. 4,500 N - Caterpillar clamping pneumatic, weight Iolhcstx Axrecqpsic compensation of the upper crawler carrier, Equalising tank for the compressed air supply - 2 transport chains 75 mm wide, 23 mm high, hardness approx. 70 Shore A profiled for roller shutter standard profile (smooth segments possible) - Protective panelling, limit switch protected - Control panel with approx. 12 m connection cable - Fixed extrusion height 1100 mm Central chain lubrication

Year of construction: 2025, Condition: new, machine/vehicle number: 30632, IDE-o/c 12002675 SINGLE SCREW CO-EXTRUDER MEB 30/5x25D (picture similar, here shown MEB H20/5x25D) - NEW machine from IDE-stock program - international size 1-30-25 - mobile on 4 swivel castors - manual height adjustment mm via threaded spindle - control cabinet integrated in the frame * incl. connection cable 5m long, 32 A CEE - control via PLC Control 20/4 with 7" touch panel * drive on/off * display screw speed * display motor load * heating on/off/lowering value * set value either via touch display or digital potentiometer - emergency stop button on the control cabinet Iiolhcceu Tgrioqpec - AC parallel shaft helical geared motor 5.2 kW air-cooled, in Z-design - screw speed max. 88 rpm - screw back pressure max. 300 bar (temporarily 350 bar) - one-piece cylinder (nitrided) with water-cooled feed zone - 3 cylinder heating zones with 3 cooling fans - material hopper, 6 liter volume, fix mounted on barrel - die connection M22x1,5 screw Ø 30 mm x 25 D - Screw for processing PVC-F - screw design acc. to drawing 1258060 - output range 1.5 to 8.0 kg/h, depending on tool back pressure - nitrided and polished, with integrated screw tip - screw take-out to the front (in extrusion direction) 4 additional heating zones - display in extruder control - sockets CEE 230V, temperature probe FeCuNi Typ L - 1 additional heating zone with heater band for union nut - 1 additional heating zone for heating hose (without heating hose) - 2 die heating zones, without heating element (as spare) melt pressure and temperature measurement - combination probe ½"-20UNF-2B, cable pluggable - pre-warning 250 bar / shutdown 300 bar - visualization in ME Control 20/4 extruder control

Condition: new, Year of construction: 2025, Functionality: fully functional, machine/vehicle number: 28978, UP-STROKE SAW UNIT BASE.3 - new machine from IDE-stock programme - Extrusion height preset to 1,100 mm - External height adjustment with 4 threaded spindles - Base frame 2.0 m long, welded tubular frame - Travelling saw sledge 500 mm * motorised via toothed belt - Saw blade drive 1.5 kW - Carbide saw blade Ø 400 mm, 120 teeth - Pneumatic saw stroke - Profile passage according to sawing diagram D-Base.3 - Down-holder bridge, limit switch protected - 2 connection pieces for dust extraction - Protective panelling with sliding door, limit switch protected * with inlet and outlet protection channel, 500 mm long - Profile guide rollers on infeed side, adjustable - control unit ME Control 20/4 * 7" touch display * 10 programmes * adjustable saw blade lifting height * tipping signal routed to terminals Islhcowcauaecqpsic

Condition: new, Year of construction: 2025, machine/vehicle number: 30765, BELT HAUL-OFF BASE.2 - new machine from IDE-stock programme - Extrusion height preset to 1,100 mm - External height adjustment with 4 threaded spindles - Base frame 2.0 m long, welded tubular frame - Driven by 2 AC motors 0.55 kW each (rated-power at 50Hz) * operation at 87Hz = 0,96 kW each - Pull-off speed 1.0 to 10 m/min - Pull-off force max. 5.360 N - Contact length approx. 1,000 mm - Pneumatic track clamping * Weight compensation of the upper caterpillar carrier * Adjustable stop for mechanical limitation mechanical limitation of the track clamping * Equalising tank for compressed air supply - 2 transport belts 200 mm wide * Hardness approx. 40 Shore A - Protective panelling with sliding door, limit switch protected * with inlet and outlet protection channel, 500 mm long - Profile guide rollers on infeed side, adjustable - Analogue operation, integrated in the control cabinet Ielhccswcaqhsqpeic

Condition: used, Year of construction: 1999, Functionality: fully functional, machine/vehicle number: 90, PUNCHING UNIT ME 41/2 - Used machine, function-tested - Frame l x w 1000 x 600 mm - Height adjustment with spindle - Travelling distance approx. 25 mm, pneumatically supported - pneumatically operated - Punching force 1,800 N / at 6 bar - Punching stroke length 10 mm - Punching sequence max. 150 strokes/min - Trigger pulse electrical Isletx Awuehccqpeic - Without punching tool - Protective panelling with hinged door Limit-switch protected, without infeed/outfeed protection channel - Removable waste container Length measurement - with contact roller and holder for punching step 64 mm - with contact roller /0 20.38 mm with one switching cam

Condition: used, Functionality: fully functional, machine/vehicle number: 460, Year of construction: 1997, EXTRUDER ME 45/3x25D - used machine, function tested - DC drive 14 kW - Screw speed 8-85 min-1 - Cylinder, one-piece, with water-cooled feed zone - 4 cylinder heating/cooling zones with 4 air blowers - 1 flange heating zone, incl. heater band - 3 mould heating zones, without heating elements - Three-point temperature controller type KS 40 with digital display, self-optimisation and error message - die connection in special design with external thread M 85 x 2, designed for melt pressure and temperature temperature measurement Mass pressure and temperature measurement - complete with 2 separate measuring probes - digital display units - incl. 2 blanking plugs Hopper - capacity approx. 60 litres - swivelling mechanism 1 Screw ø 45 mm x 25 D - 3-zone screw for processing Polyamide as per drawing 22501850 Iijlhccqjtx Av Rjpjc - Output capacity approx. 8-35 kg/h (depending on mould design) - Nitrided, polished and hollow drilled - Screw tip suitable for mould connection

Year of construction: 2025, Condition: new, Functionality: fully functional, The universal LAS 28 XLe laser marking system from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser, you can mark almost all materials such as steel, hard metal, aluminium and plastics. Depending on requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of a laser has become indispensable in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be created with just a few clicks and without extensive programming knowledge. The software automatically counts up serial and article numbers once they have been set. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer it to predefined areas. The use of a hand scanner is also possible. Iijlhccqswkpvvepoc The standard equipment includes an integrated PC with Windows operating system and laser software. The LAS 28 XLe laser model can optionally be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Other options, such as lateral cantilevers for marking long parts, movable Z-axis, drawer systems, etc., can also be implemented. Programmable, software-controlled axes (X-, Y-, Z-axis) and database connection are also possible. Made in Germany Fiber laser 30W, 20 W or 50 Watt - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - marking software EZCAD in German / English - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - optional: autofocus system - system for automatically determining the focus distance - pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - signal light for indication of operating status - max. component height approx. 300mm - electrically adjustable Z-axis - Integrated PC with Windows operating system - frame made of aluminum profile - air cooled - Door width approx. 700mm / door height(pass-through): 400mm - Connection 230V - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) - Weight: approx. 120 Kg