C Dugard Limited

Condition: ready for operation (used), Year of construction: 2019, travel distance X-axis: 150 mm, travel distance Z-axis: 240 mm, number of axes: 2, Horizontal turning machine manufactured in 2019. This SCHAUBLIN 102Mi W25 features a W25 spindle nose and an integrated motor headstock. It includes a pneumatic clamping device and a Tripan-111S quick-change tool holder system. The machine is equipped with a 3-jaw chuck and a tailstock with a rotating center. If you are looking to get high-quality turning capabilities, consider the SCHAUBLIN 102Mi W25 machine we have for sale. Contact us for further details. • Spindle nose: W25 • Headstock: Integrated motor • Mounting: Mounted on workbench (Version CE) • Cross-slide: Crank cross-slide with digital measurement device • Tailstock: Morse Taper 2 • Color: RAL7015 / RAL9010 Additional equipment • Workbench: 2000 x 800 x 900 mm • Lista drawer cabinet: 564 x 725 x 850 mm • Pneumatic clamping device W25 with graphite distributor • Tripan-111S quick-change tool holder system • Boring bar holder, 30° angled, max Ø12 mm • 3-jaw chuck W25/Ø100 (cast iron, manual) • Tailstock accessory: Rotating center 60°, Ø18 mm (Gepy) • Collet set W25 (0.5–25 mm, 50 pieces) • Mebiflex 70 lamp Hfodpfx Asy Snmvsb Nog Technical Specification Counter Spindle No Driven Tools No

Condition: ready for operation (used), Year of construction: 2009, spindle speed (max.): 4,500 rpm, travel distance X-axis: 250 mm, travel distance Z-axis: 600 mm, number of axes: 4, This 4-axis TRAUB TNC 65 DG was manufactured in 2009. It features a powerful tool drive turret with a speed of 4000 rpm and a high-pressure coolant system with programmable pressure stages. The machine is designed for machining metals and plastics, equipped with a C-axis for numerically controlled turning and positioning. If you are looking to get high-quality turning capabilities, consider the TRAUB TNC 65 DG horizontal turning machine we have for sale. Contact us for further details. • Control system TX8i with 64-bit RISC high-performance processor and additional PLC high-performance processor, integrated PC • TX8i control with 64-bit technology including TFT color flat screen and electronic handwheel • Electrical system according to VDE/EN 60204 • Multi-range transformer for 460V / 400V / 380V / 220V / 200V, 50 Hz • Operating voltage machine 400V 50 Hz • Operating voltage accessories 230V 50 Hz • Control voltage 24V DC • Machine equipped with interference suppression set for industrial networks (EMC compliant) • CE conformity declaration and CE marking • Designed for machining metals and plastics with defined cutting edge • Main spindle C-axis (numerically controlled turning and positioning device) • Counter spindle C-axis with speed-synchronous control • Tool drive turret 1: power 3.1 kW, speed 4000 rpm • Tool drive turret 2: power 3.1 kW, speed 4000 rpm • Tool monitoring TX8i with wear and breakage control via axis motor monitoring • Thread cutting without compensating chuck • Software TRAUB Polyform for milling programming with C-axis (front, longitudinal, cylindrical surface) • Network connection preparation with Ethernet interface and RJ45 socket • Z/V axis counter spindle software with defined end position (plan surface transfer) Hodpfoy Sg Nisx Ab Njfg • Maximum clamping diameter up to 60 mm depending on system Additional equipment • Workpiece unloading device with gripper in turret 2 (automation) • Chip conveyor (hinged belt), discharge height 1200 mm • High-pressure coolant system with programmable pressure stages 20 / 5 bar • Preparation for extraction and filter system, connection Ø200 mm, 400V socket • Bar feeder interface preparation DNH 61 • Collet chuck system RÖHM for spindle Ø65 mm • Reducer sleeve for main spindle Ø65 mm Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: ready for operation (used), Year of construction: 2000, travel distance X-axis: 210 mm, travel distance Z-axis: 450 mm, number of axes: 3, This 3-axis TRAUB TNA 300 horizontal turning machine was manufactured in 2000. It features a spindle diameter of 65 mm and includes a high-pressure coolant system, driven tools with 4 kW power, and an automatic bar change system. The machine is equipped with a chip conveyor and tool monitoring systems for enhanced efficiency. If you are looking to get high-quality turning capabilities, consider the TRAUB TNA 300 machine we have for sale. Contact us for further details. • Spindle diameter: 65 mm • Machine version: without tailstock • Basic configuration: included • Hydraulic hollow clamping cylinder: included • High-pressure coolant system: 12 bar / 3 bar • Control system: TX8H, 32-bit technology; processor latest generation (at time of build); parameter data on diskette • Axes/functions: • C-axis: included (numerically controlled spindle positioning and turning axis) • Y-axis: not included • Driven tools: included; power 4 kW • Monitoring and safety: • Tool breakage monitoring: included • Tool wear monitoring: included • Automatic drive shutdown after material end: selectable via parameter • Error message via parameter: selectable • Guideway cover: included • Workholding: • Collet clamping system: ROHM • Collet system compatibility: • DIN 6343 size 185E, max diameter 60 mm Hjdpfx Ajy Sg Dgeb Njfg • DIN 6343 size 48, max diameter 42 mm • Rubberflex series 52 compatible • Rubberflex series 36 compatible • Fahrion collet FM 1149 MB compatible • Fahrion collet FM 1148 MB compatible • Electrical: • Electrical system according to: VDE / EN 60204 • Operating voltage: 400 V / 50 Hz • Accessory voltage: 230 V / 50 Hz • Control voltage: 24 V DC • Multi-voltage transformer: 460 / 400 / 380 / 220 / 200 V • EMC: • Compliance: industrial class A • Standards: EN 50081 / EN 50082 / EN 55011 / EN 55022 • Machine standards: DIN EN 292; DIN EN 294; DIN EN 418; DIN EN 60204-1 • Pneumatic system: Mannesmann Rexroth ISO Additional equipment • Chip conveyor: included • Workpiece removal device: included; via conveyor, left side discharge • Bar feeder preparation: included • Bar feeder: TRAUB DNH 61-3000 (automatic) • Feeding: telescopic pusher system • Bar shapes: round / hexagonal / square • Maximum bar length: 3200 mm • Maximum bar diameter (long bars): 63 mm • Maximum bar diameter (short pieces): 65 mm • Automatic bar change: included • Residual piece removal: forward • Central adjustment of bar diameter: included • Stepless feed force adjustment: included • Central magazine adjustment: included • No guide channel change required • No clamping sleeve change required • Short remnant pieces possible • Transverse loading system • Transport weight: approx. 2100 kg Technical Specification Counter Spindle No Driven Tools No

Condition: ready for operation (used), Year of construction: 2012, spindle speed (max.): 6,000 rpm, travel distance X-axis: 81 mm, travel distance Z-axis: 80 mm, spindle motor power: 20,000 W, number of axes: 5, This 5-axis Index ABC horizontal turning machine was manufactured in 2012. It features a main spindle with a maximum speed of 6000 rpm and a sub spindle with a speed of 4500 rpm. The machine includes two turrets, each equipped with X and Z axes, and a powerful tool drive. If you are looking to get high-quality turning capabilities, consider the Index ABC machine we have for sale. Contact us for further details. • Main spindle: D65, spindle interface AD140, ID83, max speed 6000 rpm; max power 20 kW at 100% duty cycle; C-axis; electronic synchronization between spindles • Sub spindle: 7.5" chuck interface, max speed 4500 rpm • Chuck: 3-jaw KFN95/3, clamping force 480 daN, max 4000 rpm • Turrets: two turrets each with X and Z axis; tool drive on turret 6000 rpm, 3.3 kW • Rear working attachment: without quill, 5 quill positions • Coolant: 80 l/min at 8 bar and 20 l/min at 18 bar; system prepared for emulsion; coolant return at spindle end D60 (without bar feed) • Control: INDEX C200-4D based on Siemens 840D; color display 26 cm; thread cutting without compensating chuck; motor-current-based tool monitoring; internal tool management and setup dialog; extended machining cycles; parts counter and production monitoring • Power/connection data: 400 V, 50 Hz TN network; total connected load 45 kVA; rated power 38 kW; rated current 65 A; max fuse protection 100 A • Hydraulic hollow clamping cylinder D65 Additional equipment • Chip conveyor: hinged belt, discharge height 1250 mm • Bar feeder: MBL 65/3700 for spindle height 1010 mm; bar diameters up to 65 mm; bar feeder length 3700 mm; guide channel system with rolling bearings; loading rods (Ø12 mm and Ø20 mm, length 1400 mm); guide sets for 14–18 mm, 18–22 mm, 22–65 mm • Workpiece unloading device for main and sub spindle with part catcher • Teleservice preparation (ISDN) with software • Machine prepared for extraction system 230 V • Working area light • Two electrical cabinet cooling units • Transformer 3 kVA Technical Specification Counter Spindle Yes Hfodpey Sg Dasfx Ab Nog Driven Tools Yes

Condition: ready for operation (used), Year of construction: 2020, spindle speed (max.): 1,800 rpm, travel distance X-axis: 203 mm, travel distance Z-axis: 1,219 mm, number of axes: 3, This 3-axis HAAS TL-2 was manufactured in 2020. It features a maximum cutting length of 1,218 mm and a maximum cutting diameter of 203 mm. The machine is equipped with an 8" manual 3 jaw chuck and a 4-station tool turret, providing versatility for various turning applications. If you are looking to get high-quality turning capabilities, consider the HAAS TL-2 horizontal turning machine we have for sale. Contact us for further details. Hodpfx Ajy Sgvcsb Nofg • Max cutting diameter: 203 mm • Max cutting length: 1,218 mm • Spindle: A2-5 nose • Tool turret: 4-station • Functionality: Rigid tapping • Condition: Very good; very low running hours; can be checked under power Additional equipment • 8" manual 3-jaw chuck (A2-5) • Tailstock • Manual steadyrest Technical Specification Counter Spindle No Driven Tools No

Condition: ready for operation (used), Year of construction: 2013, spindle speed (max.): 6,000 rpm, travel distance X-axis: 260 mm, travel distance Y-axis: 100 mm, travel distance Z-axis: 350 mm, spindle motor power: 11,000 W, total height: 2,250 mm, total width: 1,985 mm, overall weight: 4,050 kg, controller manufacturer: OKUMA, controller model: OSP P300L, product length (max.): 1,734 mm, number of slots in tool magazine: 12, number of axes: 3, This 3-axis Okuma LB2000EXII MC was manufactured in 2013. It features a maximum swing diameter of 580 mm and a maximum machining diameter of 360 mm. The machine includes a turret head with 12 tool positions and a rapid traverse speed of 25 m/min on the X-axis. If you are looking to get high-quality turning capabilities, consider the Okuma LB2000EXII MC horizontal turning machine we have for sale. Contact us for further details. • Chuck size: 6" • Max. swing diameter: 580 mm • Max. machining diameter: 360 mm • Max. machining length: 150 mm • Spindle power: 11.0/7.5; (15/11; 22/15) kW • Turret: • Tool positions: 12 • External tooling: 20 x 20 mm • Internal tooling: Ø 32 mm • Driven tool speed: 45–6000 rpm • Driven tool power: 5.5/3.7 (7.1/4.1) kW • Rapid traverse: • X-axis: 25 m/min • Y-axis: 12.5 m/min • Z-axis: 30 m/min • W-axis: — • C-axis: 200 rpm • Hours: • Total: 43,157 • Cutting: 18,671 Additional equipment Hfodpfoy Sgr Rox Ab Njg • Bar feeder: IRCO MUK-7012 (bar Ø 6–70 mm, length 1250 mm) • Tool holders (including driven tool holders) • Collet chuck: Hainbuch SPANNTOP Technical Specification Counter Spindle No Driven Tools Yes

Condition: excellent (used), Year of construction: 2012, operating hours: 28,000 h, functionality: fully functional, Emco E25, in very good condition, year of manufacture: 2012. Fully operational. The following repairs were carried out in April 2026: Spindle bearings replaced, machine door window renewed, belt replaced, geometry checked. Available for inspection in production until calendar week 22/2026. Control system: Siemens 828 D (Shop_Turn) Inspection possible by appointment at any time. Technical specifications: Swing diameter over cross slide: 85 mm Swing diameter over bed: 250 mm Maximum turning diameter: 85 mm Maximum turning length: 225 mm Maximum bar diameter: 25.5 mm Travel: Z-axis: 300 mm X-axis: 100 mm Turret with 12 tool stations, VDI16 Spindle speeds: 0 - 6000 rpm Machine weight approx. 1200 kg Dimensions: Length: 1700 mm Width: 1250 mm Height: 1800 mm Accessories: Collet chuck for collets type 385E, Hfjdpfxey Sbide Ab Neg 6 tool holders VD16, LED signal lamp, interface for bar loader, 4 wedge clamps, machine documentation.

Condition: ready for operation (used), Year of construction: 1999, number of axes: 5, This 5-axis TRAUB TNC65 DG was manufactured in 1999. It features a robust control system with TRAUB TX8H technology, dual tool carriers with 10 stations each, and a maximum clamping diameter of 60 mm. The machine is equipped with a coolant cleaning system and a hinged belt conveyor for efficient chip removal. If you are looking to get high-quality turning capabilities, consider the TRAUB TNC65 DG horizontal turning machine we have for sale. Contact us for further details. • Control system: TRAUB TX8H (32-bit technology) • Main spindle: Yes • Counter spindle: Yes • Spindle synchronization: Yes • C-axis main spindle: Yes • C-axis counter spindle: Yes • V-axis: Yes (programmable position) • Tool carriers: 2 (tool carrier I and II) • Driven tools on tool carrier I: Yes • Driven tools on tool carrier II: Yes • Number of tool stations: 10 per tool carrier • Thread cutting: Without compensating chuck • Drilling and milling units: X-direction (i=1 and i=3) and Z-direction (i=1 and i=3) • Coolant system: Cleaning system with cyclone filter • Coolant tank capacity: approx. 470 liters • Coolant pump: Supply for both turrets integrated • Hydraulic system: Yes • Operating voltage: 400 V / 50 Hz • Control voltage: 24 V DC • Accessory voltage: 230 V / 50 Hz • Multi-range transformer: 460 V / 400 V / 380 V / 220 V / 200 V • Standards: EC Machinery Directive, EMC Directive, Low Voltage Directive, DIN EN 292, DIN EN 294, DIN EN 418, DIN EN 60204 • Tool monitoring: Tool breakage and wear monitoring • Programming software: TRAUB Polyform • Coolant type: Water-based coolant compatible Hedpfsy R Uvusx Ab Njfg Additional equipment • Chip conveyor: Hinged belt conveyor • Bar feeder: TRAUB DNH 61-3000 (preparation included) • Workpiece ejection device: Yes • Workpiece removal device: Yes, with gripper • Collet system: Röhm, max clamping diameter 60 mm Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: ready for operation (used), Year of construction: 2002, operating hours: 33,908 h, functionality: fully functional, CNC – Lathe Manufacturer: WEILER Model: E 35 D Year of manufacture: 2002 Technical data Brand: WEILER Model: E35 D Year: 2002 Center distance: 950 mm Center height: 200 mm Hfodpfx Absy R Uuks Nsg Turning diameter over bed: 410 mm Spindle bore: 54 mm Max. turning diameter: approx. 260 mm Spindle speed: 20 – 3000 rpm Power: 10 kW Dimensions: approx. L 2.60 x W 1.60 x H 1.70 m Weight: approx. 2.5 t Equipment • Operating manual • Coolant system • 3-jaw chuck • Collet chuck adapter All information subject to change without notice. A demonstration under power is possible at any time in our exhibition hall.

Condition: used, Year of construction: 2022, controller manufacturer: Fanuc, controller model: 0i-TF, _____ Description: Year of manuf. : 2022 Control : Fanuc 0i-TF Mainspindle: Technology:Motorspindle Speed (max.):10.000 rpm Power (max.):3,7 kW Barcapacity:20 mm Movement in Z (Longturning mode):205 mm Workpiececlamping:Collet chuck Guide Bush: Running synchronously Subspindle: Technology:Motorspindle Speed (max.):9.000 rpm Power (max.):1,1 kW Workpiececlamping:Collet chuck Ejector:Pneumatic Linearslide: Number of stations lathe tools:6 Taper:12 x 12 mm Number of stations Drilling unit:4 Tooldrive:8.000 U/min Number of stations front drilling quill holder:4 Taper:Ø22 mm Rear attachment: Number of stations:4 Taper:Ø22 mm Tooldrive:8.000 rpm Equipment/Accessory: Chipmanagement:Chip conveyor Hfsdjy R Iwrjpfx Ab Nsg Coolingmanagement:Coolant pump with Filter Raw-material feed:Barlaoder, FMB minimag 20 Finished-part-removal:Conveyor belt with collection tray Toolholder:Misc. static and driven toolholder Further Equipment:Trafo, Working light, Rinsing pistol

Condition: used, Year of construction: 2005, MORI - ZT1500Y - 2005 - 2 chucks and 2 revolver heads Hfodpoy R Extjfx Ab Njg - max swing 190 (typical max 170 mm) - max bar capacity appr. 65 mm - max distance between chucks appr. 1000 mm - disconnected - can be tested upon agreement - used condition as showed on photos

Condition: ready for operation (used), Year of construction: 2013, operating hours: 9,554 h, travel distance X-axis: 239 mm, travel distance Z-axis: 826 mm, number of axes: 4, This 4-axis HAAS DS-30SSY was manufactured in 2013. It features Y-axis milling capability, a sub-spindle, and live tooling, enhancing its versatility for various machining tasks. The machine includes a 12-station bolt-on turret and comes equipped with a chip conveyor and mist collector. If you are looking to get high-quality turning capabilities, consider the HAAS DS-30SSY horizontal turning machine we have for sale. Contact us for further details. • Condition: In good condition • Usage: Motion Time 54,567 h; Servo Time 62,795 h • Spindles: Dual spindle (sub-/counter spindle; rarely used) • Turret: 12-station bolt-on turret (BMT65 style) • Capabilities: Y-axis milling, live tooling • Electrical: 360–480 V, 3-phase, 50/60 Hz; Full load amps 40 A; Largest load 70 A; Short-circuit interrupting capacity 10,000 A Hfsdoy R Dikepfx Ab Njg Additional equipment • Chip conveyor (Jorgensen) • Mist collector: SARA Ultra-Jet 2 SD • Parts catcher • Coolant hose • Foot pedals Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: ready for operation (used), Year of construction: 2023, operating hours: 208 h, spindle speed (max.): 4,000 rpm, travel distance X-axis: 200 mm, travel distance Z-axis: 406 mm, number of axes: 2, Horizontal turning machine manufactured in 2023. This HAAS ST-15 features a maximum spindle speed of 4000 RPM and includes a 12-station bolt-on turret. It comes equipped with a Haas Bar Feeder and a hinged belt chip conveyor for efficient operation. If you are looking to get high-quality turning capabilities, consider the HAAS ST-15 machine we have for sale. Contact us for further details regarding this machine. • Condition: very good • Power on time: 1369:37:08 h • Cycle start time: 373:45:41 h • Feed cutting time: 208:26:21 h • Finished parts counter: 250 • M30 counter 1: 1577 • M30 counter 2: 14238 • Electrical: 440 V, 3-phase, 50/60 Hz • Full load amps: 20 A • Largest load: 18 A • Sub-spindle: not equipped (max speed 0 rpm) • LT-spindle: not equipped (max speed 0 rpm) • Memory: 1 GB Hedpsy R Dh Tsfx Ab Njfg Technical Specification Counter Spindle Yes Driven Tools No

Condition: good (used), Year of construction: 2011, functionality: fully functional, Control: Siemens 840D Spindle bore: 65 mm Speed: 4,000 rpm Tool holder: VDI 30 Hfjdpfx Aey Rr U Ueb Njg Main and counter spindle with C axis TOOL CARRIER I (XZ) Technology: Cross slide (3x) Travel: X= 70, Z= 115 mm Tool Carrier II (X/Z) Turret with 7 stations and subspindle All stations driven (3,000 rpm) Travel: X= 160, Z= 450 mm Tool Carrier III Turret with 8 stations Travel: X= 150, Z= 200 mm Tool Carrier IV (rear side) Turret with 8 stations 3 tool holders for rear side EQUIPMENT - Chip conveyor - Bar feeder IEMCA MASTER 80/33 HF

Condition: ready for operation (used), Year of construction: 2011, spindle speed (max.): 4,500 rpm, travel distance X-axis: 210 mm, travel distance Z-axis: 380 mm, controller manufacturer: OKUMA, controller model: OSP‑P200LA‑R, number of axes: 3, This 3-axis Okuma GENOS L200E-M was manufactured in 2011. It features a maximum turning diameter of 200 mm and a Z-axis travel of 380 mm. The machine is equipped with a 12-station turret with driven tools, allowing for milling and drilling on the C-axis. If you are looking to get high-quality turning capabilities, consider the Okuma GENOS L200E-M horizontal turning center we have for sale. Contact us for further details. • Turning configuration: 2 axes (X, Z) + C‑axis; no Y‑axis • Tailstock: Equipped • Tool presetter: Automatic tool presetter installed • Turret: 12‑station turret with driven tools (milling and drilling on C‑axis) • Max. turning diameter: 200 mm • Spindle nose: ASA A2‑6 • Spindle bore diameter: approx. 50 mm • Electrical supply: 380 V, 3‑phase, 50/60 Hz • Average apparent power: 17.7 kVA • Full‑load current: 26.7 A • Max. motor current draw: 45 A Technical Specification Counter Spindle No Driven Tools No Hedpsy Rrwvefx Ab Nofg

Condition: used, Year of construction: 2012, functionality: fully functional, 1 OKUMA CNC Lathe Model LT2000EX-2M1Y with OSPP200LA CNC Controller Including CE mark Hfsdpfxey Rnbdo Ab Neg 1 set 〈European Standard Specification〉 1-1 Spindle motor VAC 11/7.5 kw (5 min./cont. ) 2 set 1-2 Spindle speed 50 - 6,000 min-1 2 set 1-3 Spindle dia. 62/100 mm, 140 Flat nose 2 set 1-4 C-axis control, 360 degree at 0.001 degree increment 2 set 1-5 Y-axis 95mm (+50 to -45) for upper turret 1 set 1-6 Upper V16 (turning & milling) + Lower V16 (turning & milling) Radial turret (No tool holder included) 1 set 1-7 Rotary tool drive motor, PREX 5.5/3.7kw (2 min/count) 2 set 1-8 Rotary spindle speed 45-6,000 min-1 2 set 1-9 Coolant supply system, 0.8kw x 3 sets pump motor 1 set 1-10 Work light, fluorescent lamp 1 set 1-11 Totally enclosed guard 1 set 1-12 Door interlock 1 set 1-13 Chip pan, side chip disposal type 1 set 1-14 Foundation washers and leveling jack screws 1 set 1-15 Machine lifting hooks 1 set 1-16 Chuck auto open / close with confirmation 2 set 1-17 Chuck air blower 2 set 1-18 Lubrication monitor B-1 1 set 1-19 CE mark and EMC 1 set 1-20 Application for IEC standard 1 set 1-21 Double chuck operation pedal 2 set 1-22 Synchronized tapping (for LT2000EX-M) for Milling rotary tool 1 set 1-23 OSP-P200LA CNC Controller with 15" colour display, touch panel 1 set 1-24 OSP-P200LA 3D-M-E kit specifications 1 set *Multitasking machines Coordinate conversion (1 set) *Multitasking machines Profile generation (1 set) *Program storage Standard: 2GB (1 set) *Operation buffer Standard: 2MB (1 set) *Real 3D simulation (1 set) *Cycle time over check (1 set) *Load monitor (spindle, feed axis) (1 set) *NC operation monitor (incl. counter and monitoring function) (1 set) *Cycle time reduction function (1 set) *Variable spindle speed control (1 set) 1-25 Pitch error compensation X + Ys + Z 1 set 1-26 Inch / metric switchable function 1 set 1-27 Workpiece jump out detection 1 set 1-28 Status indicator lamp (2-layer lamp) instead of status indicator in 3D-E kit 1 set 1-29 Electrical power source application to suite local power source at each countries (CE transformer) 1 set 1-30 Chuck open/close during spindle rotation (LT-Standard) 1 set 1-set of tools - see last photo

Condition: excellent (used), Year of construction: 2014, operating hours: 27,000 h, functionality: fully functional, Pump + Filter + Cooler Hsdpsy Rlbzefx Ab Njfg No. 06 Axial Driven Tools No. 13 Radial Driven Tools Toolholder Boring Bar Holder Steady Rest: Magazine Bushings + Sleeves: Ø51/ Ø46 / Ø41 No. 02 new sets of MBL magazine bushings No. 02 optical scales overhauled by HEIDENHAIN 1 Baluff socket Grippers for Gantry Various sensors, proximity, cables Belts for driven tools: 6 pcs Set of anti-vibration bushings for MBL magazines

Condition: used, Year of construction: 1999, machine/vehicle number: IntNr231509, A Miyano BNE-51S CNC lathe with IEMCA BOSS 552-HD bar feeder is for sale. Year of manufacture: 1999 Control: FANUC Series 18-T (dual-channel control) Technical Data Max. bar diameter: 51 mm Max. turning length: approx. 125 mm Travel paths: * X1 / X2: 150 mm / 115 mm; Z1 / Z2: 380 mm / 125 mm Y-axis: +/- 40 mm (upper turret) Spindles (main & sub spindle): Speed range: 135 – 5,000 rpm (both spindles) Drive power: 11 kW / 15 kW (main spindle) C-axis: 0.001° on both spindles for complete contour machining Tool system (2 x turrets): Turret 1 (upper): 12 stations (all live, including Y-axis) Turret 2 (lower): 12 stations (all live) Live tool speed: max. 3,200 rpm Bar feeder: IEMCA BOSS 552-HD Hedjy Rft Ropfx Ab Nofg Bar diameter range: 5 mm to 51 mm Bar length: up to 3,200 mm Chip conveyor Batec fire extinguishing system The machine can be inspected under power by prior arrangement. Technical data and specifications are subject to change and prior sale excepted.

Condition: used, Year of construction: 2013, machine/vehicle number: IntNr231584, For sale is a robust ACCUWAY UT-300 CNC slant-bed lathe, year of manufacture 2013, including a FEDEK DH-65L bar feeder. Technical Specifications Control: FANUC 0i-TC Hsdey N Tu Hepfx Ab Nofg Number of axes: 2 (X/Z) X-axis travel: 300 mm Z-axis travel: 750 mm Rapid traverse X-axis: 20 m/min Rapid traverse Z-axis: 24 m/min Spindle speed: up to 3,500 rpm Bar capacity: 75 mm Spindle motor power: approx. 15 / 18.5 kW Tool turret: 12 stations Tailstock Machine weight: approx. 5,500 kg Machine dimensions: approx. 3,300 × 1,800 × 1,800 mm FEDEK DH-65L Bar Feeder Bar length: approx. 1,500 mm Bar diameter: approx. 5–65 mm Interface: bar feeder interface available The machine can be inspected by appointment. Subject to prior sale and to changes and errors in the technical data and specifications.

Condition: ready for operation (used), Year of construction: 2007, travel distance X-axis: 161 mm, travel distance Y-axis: 100 mm, travel distance Z-axis: 580 mm, number of axes: 7, This 7-axis Nakamura Tome WY-250 was manufactured in 2007. It features a twin spindle configuration with Y-axis capabilities on both turrets, allowing for versatile machining. The machine includes a maximum Z-axis travel of 580 mm and Y-axis travel of mm. If you are looking to get high-quality turning capabilities, consider the Nakamura Tome WY-250 horizontal turning machine we have for sale. Contact us for further details. • Travels: • X1: 160.5 mm • X2: 165 mm • Z1/Z2: 580 mm • Y1: mm • Y2: / mm • Included tooling: • 4x external tool holders • 4x tool holders for simultaneous mounting of 2 opposite tools • 6x boring bar holders • Driven toolholders (HEIMATEC): • 4x radial Hfjdpfsy N Spcjx Ab Nsg • 4x axial • Collet holders (Bellegrandi): • Main spindle: MSCNT70-A6” for BA & BD collets size 70, complete with related cups • Counter spindle: MSCTNR70-A5” for BA collets size 70, complete with spring ejector Additional equipment • IEMCA Master 880/33/P bar feeder (2003), S/N: 0200347S03 • Application: Automatic bar feeder for CNC lathes • Capacity: • Max bar length: 3300 mm (to be confirmed) • Max bar diameter: up to Ø80 mm (model family reference) • Guide channels: Ø65 mm included; Ø70 mm currently installed and can be supplied with the machine • Features: Automatic loading/feeding, synchronization with lathe cycle, compatible with spindle liner/guide channel systems, heavy-duty frame • Condition: Currently stopped/not in production; reported functional; available for inspection by appointment • Note: Sold together with the Nakamura Tome WY-250; some accessories/guide channels may belong to the lathe setup • Complete set of hand jaws (“Manine”) for parts unloader (parts unloader itself not specified) Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: ready for operation (used), Year of construction: 2000, travel distance X-axis: 230 mm, travel distance Z-axis: 520 mm, overall weight: 4,100 kg, number of axes: 5, This 5-axis MORI SEIKI SL-153 SMC was manufactured in 2000. It features a maximum X-axis travel of 230 mm and Z-axis travel of 520 mm. The machine includes a hydraulic chuck system, chip conveyor, and multiple driven tool holders for enhanced machining capabilities. If you are looking to get high-quality turning capabilities, consider the MORI SEIKI SL-153 SMC horizontal turning machine we have for sale. Contact us for further details. • Machine configuration • Enclosed CNC lathe • Hydraulic chuck system • Foot pedal included Hsdjy N Shljpfx Ab Njfg • Automatic bar feeder interface likely installed • Tooling and included holders • 3x radial driven tool holders • 4x axial driven tool holders • 2x for main spindle machining • 1x for counter spindle machining • 1x shared output for both spindles • 2x special double boring bar holders (bore Ø20 mm) • Prepared for Schunk TendoTurn DSE hydraulic clamping accessories (Schunk accessories not included) • Multiple external tool holders • Axial tool holders • Boring bar holders with Ø25 mm and Ø32 mm bores • Accessories for direct mounting of square shank tools on turret • Collet holders • 2x Bellegrandi collet holders type MSCTN52 & MSCTNR52 • Suitable for BA and BD type collets size 52 • For main and counter spindle use • Electrical data • Voltage: 200 V • Frequency: 50 Hz • Full load current: 116 A • Spindle motor current rating: 76 A • Rated power: 40 kVA • Condition • Currently disconnected • Reported functional before removal • Available for inspection Additional equipment • Chip conveyor included (separate accessory) • LNS Hydrobar Sprint 555 / 3M automatic bar feeder • Serial number: 220250 • Year: 2006 • Bar length capacity: 3000 mm • Guide channel suitable for turning applications • Compatibility: Seller states compatible with Mori Seiki SL-153 SMC with minor modifications; reportedly never worked with this lathe previously • Condition: Reported functional Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: ready for operation (used), Year of construction: 2012, spindle speed (max.): 3,800 rpm, travel distance X-axis: 280 mm, travel distance Z-axis: 500 mm, spindle motor power: 22,000 W, number of axes: 5, This 5-axis Okuma LB 300M X 500 was manufactured in 2012. It features a maximum turning diameter of 340 mm and a turning length of 480 mm. The machine is equipped with a powerful spindle speed range of 45 - 3,800 rpm and a robust turret with 12 stations. If you are looking to get high-quality turning capabilities, consider the Okuma LB 300M X 500 horizontal turning machine we have for sale. Contact us for further details. • CNC: OSP U100L • Max turning diameter: 340 mm • Max turning length: 480 mm • Distance between centers: 500 mm • C-axis: 360° (0.001° increment) • Rapid feed: X 20,000 mm/min; Z 25,000 mm/min • Spindle nose: ASA 6 • Bar capacity: 65 mm • Live tooling: 45–4,500 rpm; 3.3 kW • Turret: V 12 NCM (12 stations); VDI 40 • Tool section: 25 mm (square) / 40 mm (boring bar) • Tailstock: quill Ø 90 mm; travel 120 mm; taper MT5 • Certification: CE certified with manuals Additional equipment Hodpfx Aoy N Sabob Njfg • Kitagawa B208 chuck • Chip conveyor • High-pressure coolant pump • Robot interface • Automatic door • Air blow • Turning tool holder kit • 4 radial live tools • 4 axial live tools Technical Specification Taper Size VDI 40 Counter Spindle No Driven Tools Yes

Condition: ready for operation (used), Year of construction: 2002, operating hours: 22,542 h, spindle speed (max.): 5,000 rpm, travel distance X-axis: 570 mm, travel distance Z-axis: 635 mm, controller manufacturer: FANUC, controller model: Series 21i-T, number of axes: 3, This 3-axis Gildemeister CTX 400 Serie 2 was manufactured in 2002. It features a spindle speed of up to 5,000 rpm and a z-axis travel of 635 mm, along with an x-axis travel of 570 mm over the bed. The machine includes a 12-position turret and is equipped with a 3-jaw chuck, chip conveyor, and coolant system. If you are looking to get high-quality turning capabilities, consider the Gildemeister CTX 400 Serie 2 machine we have for sale. Contact us for further details. • X-axis travel: max. 570 mm (over bed) / 420 mm (over slide) • Voltage: 400 V • Frequency: 50 Hz • Power capacity: 44 kVA • Rated current: 64 A • Main fuse: 80 A • Control voltage: 230 V (AC) / 244 V (DC) • Working hours: 22,542 hours • Feed time: 8 hours 4 minutes • Turret: 12-position turret • Tooling capability: driven tools; C-axis displayed on screen Additional equipment • 3-jaw chuck • Chip conveyor • Coolant system • Workspace lighting • Optional: Tool Holder Package Hsdjy Nynyjpfx Ab Nofg • Optional: Schunk Rota NCD 210-66 three-jaw chuck Technical Specification Counter Spindle No Driven Tools Yes

Condition: excellent (used), Year of construction: 2000, INDEX ABC 60 Spindle automatic CNC operational, fully functional Year: 2000 Condition: very good, operational Ready for immediate delivery Machinery runs without any problems. Technical details: 1-Spindle Automatic CNC Fized Headstock Lathe Serial number 400290 control SIEMENS 840 C passage: 65 m tool turrets with driven tools: 2 front and rear side machining chip conveyor: KS SRF 040.00 Bar loading: SCHMID LN 3200 Weight machine: 3500 kg. Overall size: 6500 x 1500 x 1800 mm. Hjdpoy Nycdjfx Ab Nsfg We are waiting for you in H.B.R. srl - ITALY

Condition: good (used), Year of construction: 2011, operating hours: 13,390 h, functionality: fully functional, turning length: 550 mm, turning diameter: 280 mm, spindle speed (max.): 5,000 rpm, travel distance X-axis: 200 mm, travel distance Z-axis: 515 mm, spindle motor power: 11,000 W, rapid traverse X-axis: 15 m/min, rapid traverse Z-axis: 24 m/min, total height: 1,800 mm, total length: 2,100 mm, total width: 1,350 mm, quill travel distance: 500 mm, quill diameter: 60 mm, quill stroke: 125 mm, type of input current: AC, torque: 121 Nm, overall weight: 4,000 kg, chuck outer diameter: 225 mm, Equipment: documentation/manual, For sale is a TC400 52MC CNC lathe from the renowned German manufacturer Spinner Werkzeugmaschinenfabrik GmbH, built in 2011. The machine is in good used condition and has only 13,390 hours of active control time, of which just 3,341 hours are machining time. It has not been in operation in the last five years and was serviced by a Spinner technician in July 2025. Hodpey Nxd Hefx Ab Nofg The lathe features a 12-station driven tool turret, automatic workpiece removal with conveyor belt, a chip conveyor, and four foot switches. The original technical documentation in German and English, the electrical wiring diagrams, service book, recent maintenance reports, the original invoice, and several tool booklets are included. Various tools are also provided. All are functional and some are barely used. Manufacturer: Spinner Werkzeugmaschinenfabrik GmbH Model: TC400 52MC Machine No.: AU0474 Year of manufacture: 2011 Weight: 4,000 kg Please refer to images 2, 3, and 4 for detailed technical specifications extracted from the official documentation. The price includes the machine itself, a selection of tools and accessories, and loading onto a truck (a suitable forklift is available). Shipping or collection must be arranged by the buyer and is not included in the price. The listed price is net. If you are interested, please contact us via email, direct message, or phone. For functional verification, we will gladly provide a current video upon request. Fitok GmbH, Moritz Hanesch, 07.05.2026