RS-ImmoPro GmbH

Condition: used, Year of construction: 2016, Makino A51NX in very good condition, including a new ATC tool changer and Cubes. Approx. 11,000 hours of cutting time. Capacity & Travels: Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Workpiece: ∅ 630 mm × 900 mm Max. Payload Capacity: 400 kg Spindle: Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Motion & Feed Rates: Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cutting Feedrate: 50,000 mm/min Axis Acceleration: 1G B-Axis Indexing: Full 4th axis, Direct Drive (0.001-degree increments) Tooling: ATC (Automatic Tool Changer) Capacity: 60 tools Tool-to-Tool Time: 0.9 seconds Max. Tool Diameter / Weight: 170 mm / 12 kg 04003 HSK-A63 Spindle – Replaces the standard ISO50 interface. Features a double taper, full face contact, and hollow shank interface. Tool clamping force is higher than 44kN; HSK tool holders are required. 14017 HSK holders for 60 Tool ATC 26001 Moire Scale Feedback X, Y, Z-Axis Increments 0.05µm, positioning tolerance Tp = 0.006mm (ISO 230-2). 29006 Through Spindle Coolant 3.0MPa – Provides TSC flow of 30 l/min at 3.0MPa, replacing the standard 1.5MPa. Air through the spindle is possible. The pressure data refers to the output flange of the pump. 29009 Flow Switch for Through Spindle Coolant – Monitors through-spindle coolant flow. The machine will feed hold if the flow is below a preset level. Note: Recommended option for filtration systems to prevent tool damage. 31002 Air curtain for splash guard window – Located in the middle of the operator-side window, this air curtain prevents chips and coolant from obstructing the view. 37000 Broken tool sensor outside machining area (BTS) – Tool breakage detection for centric tools (tool diameter 1-40mm, tool length 65 - 430mm). Length measurement is performed using a movable probe. The measurement takes place in the ready position for a tool change, outside the machining area. Accuracy ± 2mm. If there is a difference between the measurement before and after machining, an alarm is triggered automatically. 37101L Automatic Workpiece Measuring Device (RENISHAW OMP60) – Three-coordinate measuring probe from RENISHAW with automatic coordinate correction. The signal is transmitted via infrared. Tolerance approx. 0.005mm. 14 automatic measurement cycles are available as pre-programmed cycles in the program memory. Note: requires 13m. Control Options: Ncedezg N E Hjpfx Aniju 60001 Automatic Corner Override (G62) – Automatically decelerates the cutter at a corner depending on the corner angle, in order to maintain the cutting rate per unit time. 62007 Run hour and parts quantity display. 63034 DATA CENTER Storage Type B (total: 800MB) – Communication card with internal 800MB removable flash RAM card used for storing and executing NC data (of subprograms) for high-speed, high-definition finishing and supporting SGI capabilities. CNC programs can be transferred to and from a CAD/CAM system from the operator's pendant by FTP get and put commands over an Ethernet cable. 66003 Additional 48 Work Offsets (G54.1 P1-P48) – Allows for 48 work coordinate systems, simplifying multiple part fixtures. 68010 600 Macro Common Variables – Variable numbers 100-199 are reset and cleared when the power is turned off, while 500-999 are permanent. Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Payload Capacity: 400 kg Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cut...

Condition: used, Year of construction: 2006, operating hours: 59,800 h, machine/vehicle number: IntNr231615, A compact, high-precision horizontal CNC bar feed milling machine is for sale: ALMAC FB 1005 CNC, manufactured in 2006, equipped with a FANUC 16i-MB / 161MB control system. Technical data: Manufacturer: ALMAC / Tornos Type: FB 1005 CNC Year of manufacture: 2006 Control system: FANUC 16i-MB / 161MB Axes: 6 axes Travel ranges X / Y / Z: 280 / 230 / 120 mm Working feed rate X / Y / Z: Rapid traverse: 12 m/min Resolution: 0.001 mm Front spindle block: with spindles Side spindle block: 4 spindles Vertical spindle block: 4 spindles Parting spindle: 1 spindle Rear machining: 2 or 3 spindles Standard spindle: Speed: 1,000–12,000 rpm Power: 1.4 / 3.4 kW Parting spindle: Speed: 100–3,000 rpm Power: 1.4 / 3.4 kW Tool holder: ESX 20 / HSK 32-A Indexing table / C-axis: Bar feed: Njdpfx Anszgggbjiscu Pneumatic: 25 mm or CNC W-axis: 50 mm Swiveling / B-axis: Manual: 0–20° or CNC B-axis: 0–20° or -5° to +45° for short bars Coolant system: Coolant tank: 205 l Flow rate: 40 l/min Standard filtration: 35 µm / 28 µm Temperature control: 3,000 W for ΔT 3 °C Connection data: Installed power: 10 kVA Voltage: 3 × 400 V / 50 Hz Compressed air: 6 bar Dimensions with bar support: L × W × H: 1,800 × 4,250 × 2,060 mm Weight: approx. 1,800 kg The machine can be inspected in operation by prior arrangement. Subject to changes, errors and prior sale.

Condition: used, Year of construction: 2012, operating hours: 37,500 h, machine/vehicle number: IntNr231616, Ncedpfxezggfqj Anieu

Condition: ready for operation (used), Year of construction: 2005, operating hours: 44,673 h, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 900 mm, controller model: OSP-E100M, spindle speed (max.): 12,000 rpm, number of slots in tool magazine: 320, No minimum price – guaranteed sale to the highest bidder! Submitting a bid obligates the bidder to collect the machine on schedule in week 30 of 2026! TECHNICAL DETAILS Travel range X-axis: 1,000 mm Travel range Y-axis: 900 mm Travel range Z-axis: 900 mm Spindle speed: 12,000 rpm Tool holder: BT50 Tool positions: 320 Tool positions for 600 mm tools: 80 Part accuracy: 0.001° MACHINE DETAILS Control system: OSP-E100M Number of axes: 4 Coolant pressure: 30 bar Nedpozd Tapjfx Anijcu Operating hours NC cycle time: 71,235 h Spindle running time: 56,241 h Machining time: 44,673 h EQUIPMENT ATC with 320 positions 80 positions for 600 mm tools 2 pallets Balluff writing/reading system NC table Absolute scales in X, Y, and Z Renishaw MP10 measuring probe Tool breakage monitoring MOP tool monitoring 30-bar coolant system Mayfran Consep 2000 chip conveyor

Condition: ready for operation (used), Year of construction: 2001, functionality: limited functionality, travel distance X-axis: 600 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 500 mm, controller manufacturer: Siemens, spindle speed (min.): 10,000 rpm, spindle speed (max.): 10,000 rpm, distance between spindles: 600 mm, number of spindles: 2, number of slots in tool magazine: 80, axle spacing: 600 mm, Equipment: chip conveyor, Schwäbische Werkzeugmaschine GmbH Twin-spindle machining center BA 600-2 Year of manufacture: Spindle distance: 600 mm Tool interface: 2 x HSK 100, 10,000 rpm Ncodpszdq Scofx Anieu The machine is still in production and can be inspected during ongoing production. Various repairs are required. 8-station hydraulic clamping system per tool changer.

Condition: excellent (used), 3-axis machining center Work area: 1350 x 2565 mm. Njdpszcpfajfx Aniocu Workpiece clamping via vacuum pump.

Condition: refurbished (used), Year of construction: 2010, functionality: fully functional, machine/vehicle number: 234, overall weight: 450 kg, spindle speed (max.): 48,000 rpm, input voltage: 400 V, type of input current: three-phase, WITECH MiC5 5-axis simultaneous machining center, a compact, high-precision machine designed for micromachining, watchmaking, medical applications, prototyping, and machining of complex parts. In perfect condition; video available upon request. Key features: 5-axis continuous simultaneous machining Travel: X 160 mm – Y 100 mm – Z 220 mm Rotary axis A: 360° continuous Axis B: ±70° (140°) High-speed spindle up to 48,000 rpm HSK-E25 tool holder Cybelec Fastware CNC control Automatic tool changer Compact and rigid machine Complete machine, available for inspection Ncjdpfxozbbk Es Anieu Perfectly suited for machining small, high-precision parts requiring complex 5-axis geometries. For more information, additional photos, or a demonstration, please contact me. Year of manufacture: 2010 Spindle condition: overhauled Exact number of tools in the magazine: 10

Condition: used, Year of construction: 2005, operating hours: 40,300 h, machine/vehicle number: IntNr231576, A used AXA VSC-1M/2E CNC vertical machining center, manufactured in 2006 and equipped with a HEIDENHAIN iTNC 530B CNC control, is for sale. Technical data Design: Moving column machine Number of axes: 3 axes Machining operations: Milling, drilling, threading Operating mode: CNC operation Swivel machining Tool holder: SK 40 Tool magazine Chip conveyor Coolant system X-axis travel: 1,760 to 9,000 mm Y-axis travel: 550 mm Z-axis travel: 600 mm Distance from table to spindle nose: 180 to 780 mm Table surface: X-travel + 400 mm x Y-travel, 3 T-slots 14 H9, T-slot spacing 160 mm Table load: 800 kg/m² Rapid traverse: 30 m/min The standard tool changer has 22 tool positions; optional extensions up to 216 tool positions are possible. Tool change time: approx. 4 seconds. The machine can be inspected by appointment. Ncodpfszatgpox Anieu Subject to changes and errors in the technical data and specifications, as well as prior sale.

Condition: used, Year of construction: 2001, machine/vehicle number: IntNr231491, Manufacturer: DECKEL MAHO, Model: DMF 220 linear, Year of manufacture: 2001 Control system: Siemens 840D Powerline Travel and Axes X-axis (longitudinal): 2,200 mm Y-axis (transverse): 560 mm Z-axis (vertical): 720 mm Rapid traverse X/Y/Z: 50 m/min X-axis drive: High-dynamic linear drive Work Table Clamping surface: 2,600 x 600 mm Max. table load: 2,200 kg Main Spindle Speed range: 20 - 12,000 rpm (standard) Drive power (100% duty cycle): 35 / 25 kW (S1/S6) Max. torque: 130 / 87 Nm (at 100% duty cycle) Tool holder: SK 40 according to DIN 69871 Tool Changer Number of stations: 30-position magazine Tool change time (chip-to-chip): approx. 4-6 seconds (depending on model) Dimensions & Weight Space requirement approx.: 6,500 x 3,500 mm Machine weight approx.: 12.5 t The machine can be inspected under power by appointment. Technical data and specifications subject to change and error; prior sale reserved! Refurbished 5-axis CNC machining center Deckel MAHO DMF 250 linear in good condition. Year of manufacture: 2004. Control: Heidenhain iTNC 530. Technical data: X travel: 2,500 mm. Y travel: 920 mm. Nodpfjy U Hklsx Aniecu Z travel: 820 mm. B-axis: x/- 105° Worktable: 3,100 x 900 mm Spindle interface: HSK 63 Spindle speeds: 20 - 18,000 rpm Tool changer: 30 positions Equipped with: - Chip conveyor - Through-spindle coolant 40 bar - Operating manual Country of origin: Germany Motor power: 35 kW Machine dimensions (LxWxH): 6,000 x 3,800 x 2,950 mm Machine weight: 25,000 kg The machine can be viewed by appointment. Technical data and specifications subject to change and error, as well as prior sale!

Condition: used, Year of construction: 2026, consisting of: machine base, 2 rotary spindles, SIEMENS Sinumerik S7-1500 control system (see photos), 1 RITTAL SK3185830 control cabinet cooling unit, 1 machine base plate (stored outdoors). Nodpey T N Abofx Aniscu

Condition: used, Year of construction: 2014, operating hours: 30,663 h, machine/vehicle number: 87391, Control system: HEIDENHAIN TNC530, travel range X/Y/Z: 2x 750x500x600 mm, swiveling table, tool holder: SK40, 22 tool positions, chip conveyor: AXA FSB 300/TLG:38,1, serial number: 171153-1, 87391, year of manufacture: 2014. Ncedpjy T Nygjfx Anieu

Condition: used, Year of construction: 2014, operating hours: 33,100 h, machine/vehicle number: 2941, Control system: HEIDENHAIN TNC530, travel range X/Y/Z: 3,500 x 1,200 x 1,250 mm, swivel head: 2.5°, tool holder: SK50, 60 tool positions, chip conveyor: URRETXU 11-20132, serial number: 4855492004U5E2, filter system: JUMA+GAIN, serial number: 7136, capacity: 60 l/min, year of manufacture: 2013. Ncodpfx Anjy T Nx Njieu

Condition: used, Year of construction: 2021, operating hours: 13,640 h, machine/vehicle number: 21121341, Catalog No.: 1.2, 3 shielded machining centers with plexiglass windows, each 250x300 cm, HEIDENHAIN TNC-640 control system, 6 controlled axes, tool holder SK50, table surface: 9,000x2,000 mm, max. table load: 30 tons, travel distances X/Y/Z: 8,000/1,300/2,500 mm, special equipment: universal milling head that automatically pivots continuously in 2 planes, internal coolant system, 60-position tool changer, rotary table (10 tons, 1,500x1,500 mm), clamping surface, continuously positionable, measuring probe RENISHAW, 4 clamping angles, external programming option via Mastercam, subject to prior sale. Ncodpfoy T Nx Ajx Aniju

Condition: used, Year of construction: 2022, Volume flow rate: 18,000 m³/h, active filter area 237.6 m², condensate drain, designed for 10 machining centers, mounted on a custom-built steel frame above the hall entrance gate, complete with piping, manufactured to the dimensions of the hall, and intended as a supply line to the individual CNC machining centers. Subject to prior sale. Nsdpfx Ansy T Nxvjiocu

Condition: used, Year of construction: 2019, operating hours: 23,121 h, machine/vehicle number: 14505774804, Catalog No.: 1.1, chip conveyor, HEIDENHAIN TNC-640 control system (5 axes/simultaneous), 60-position tool changer SK40, table surface/simultaneously controllable rotary table: 630x500 mm, max. table load: 200 kg, travel ranges X/Y/Z: 650/520/475 mm, direct measuring systems for B- and C-axes, plane transformation, connection to central oil mist extraction system, external programming option via Mastercam, with 1 workpiece automation system from HALTER, type: LoadAssistant U-35, year of manufacture: 2019, serial number: DCH0284, item code: X92850, sales order no.: DS09801, with 3D robot Assistant Automation S180-20 handling robot from FASTEMS, subject to prior sale. Ncedpfsy T Nxpex Aniou

Condition: used, Year of construction: 2020, operating hours: 13,641 h, machine/vehicle number: 00820028701, Catalog No.: 2.3, as a twin-spindle machine, with SIEMENS 840D sl Operate control system, max. speed of turning and milling spindle: 10,000 rpm, max. drive power: 20 kW, max. torque: 120 Nm (100% duty cycle), largest turning diameter: 360 mm, largest turning length: 800 mm, bar passage: 102 mm, Capto C6 tool changer, tool magazine chain with 80 magazine slots, Y-axis travel: +/- 100 mm for eccentric machining, swivel range of the B-axis: +/- 110°, special equipment: counter-spindle with tailstock function, groove stop function, connection to a central oil mist extraction system, external programming option via Mastercam, chip conveyor, subject to prior sale. Nsdpfx Ajy T Nxcjniscu

Condition: used, Year of construction: 2020, operating hours: 17,031 h, machine/vehicle number: 00830004341, Catalog No.: 2.2, as a twin-spindle machine, SIEMENS 840D sl Operate control system, max. speed of turning and milling spindle: 10,000 rpm, max. drive power: 20 kW, max. torque: 120 Nm (100% ED), largest turning diameter: 360 mm, largest turning length: 1,200 mm, bar capacity: 102 mm, Capto C6 tool changer, tool magazine chain with 80 magazine positions, Y-axis travel: +/- 120 mm for eccentric machining, swivel range of the B-axis: +/- 110°, special equipment: hydraulic self-centering steady rest (25-199 mm), counter-spindle with tailstock function, fine chip removal system for cast iron machining, groove milling function, connection to central oil mist extraction system, external programming option via Mastercam, chip conveyor, subject to prior sale. Nsdpfxoy T Nw Ej Anijcu

Condition: used, Year of construction: 2023, operating hours: 4,115 h, machine/vehicle number: C1020020.001, Turning length: 3,000 mm, CNC control system SIEMENS Sinumerik 840 D Solutionsline, 1 additional unit as an external cylindrical grinding machine, 1 transport trolley with accessories: 2 steady rests, 1 RÖHM Duro-T 400 3-jaw chuck, turning diameter over the bed: 560 mm, turning diameter over the carriage: 365 mm, spindle bore: 82 mm, subject to prior sale. Nsdpey T Nwxjfx Anijcu

Condition: used, Year of construction: 2021, operating hours: 14,800 h, machine/vehicle number: 14505787934, Catalog No.: 1.6, with automatic loading, DMG MORI DMU 50, control system HEIDENHAIN TNC-640 (5 axes/simultaneous), tool holder SK40, clamping surface/simultaneous rotary table: 630x5,000 mm, max. table load: 200 kg, travel distances X/Y/Z: 650/520/475 mm, special features: direct measuring systems for B and C axes, plane transformation, connection to a central oil mist extraction system, external programming option via Mastercam, chip conveyor, subject to prior sale. Njdey T Nwlepfx Aniocu

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, For technical data, see images.... Ncedjy Tl N Ropfx Aniju

Condition: new, Year of construction: 2024, X-axis 4,400 mm Y-axis 1,600 mm Z-axis 900 mm Spindle speed 2,000 - 24,000 rpm Drive power 14 kW Tool holder HSK 63 Tool changer 12 positions Control SIEMENS SINUMERIK ONE The machine has never been assembled and is immediately available. Nodpfoy Ix Upex Aniocu

Condition: used, Year of construction: 2022, machine/vehicle number: 246/22, feed length X-axis: 2,000 mm, feed length Y-axis: 300 mm, feed length Z-axis: 300 mm, rotational speed (max.): 18,000 rpm, overall weight: 5,000 kg, Designation: Fanum TRIO SP 2W30 Weight: approx. 5,000 kg Number of spindles: 2 Axes: Nsdpfx Aney H I Tljijcu X-axis (width): 2,000 mm Y-axis (length): 300 mm Z-axis: 300 mm Spindle data Spindle type: ES789 Spindle power (S1/S6): 15 / 18 kW Max. speed: 18,000 rpm Spindle interface: HSK A63 Tool holder: ER32 / ER40

Condition: used, Year of construction: 2011, Pallet: 500 x 500 mm X: 730 mm Y: 730 mm Z: 740 mm Maximum detail size: Ø 800 x 1000 mm Max load capacity: 700 kg Spindle speed: 12 000 r/min - High-torque Spindle effect: 22/30 kW , 300 Nm (AC40HP) CAT 40 Tool changer: 40 positions Interface for coolant system Prepare for probe OMP60 Cromar conveyor Synchronised tapping G00 slope constant EIA EIA 3D COMP Scaling included loading of machine included tools and cubes Mazak HC Nexus 5000-II: LxWxH: 475 x 238 x 285 cm Pallet: 500 x 500 mm X: 730 mm Njdpey H Dnxefx Aniecu Y: 730 mm Z: 740 mm Max load capacity: 700 kg Tool changer: 40 positions

Condition: used, Year of construction: 2004, Makino A66E with Fastems 10 pallet system built in container. Length of the working table 500.4 mm Width of the working table 500.4 mm Ncsdpfsy D Sirjx Anieu Maximum table load 700 kg Antalet verktyg i magasinet 136 st Maximum spindle speed 14000 rpm Travel length X-axis (mechanical feed) 729 mm Travel length Y-axis (mechanical feed) 729 mm Travel length Z-axis (mechanical feed) 797.6 mm Maximum feed rate in X-axis 1250.1 mm/s Maximum feed rate in Y-axis 1250.1 mm/s Maximum feed rate in Z-axis 1250.1 mm/s

Condition: used, Year of construction: 1993, functionality: fully functional, travel distance X-axis: 8,000 mm, travel distance Y-axis: 2,500 mm, travel distance Z-axis: 700 mm, rapid traverse X-axis: 10 m/min, rapid traverse Y-axis: 10 m/min, rapid traverse Z-axis: 10 m/min, feed rate X-axis: 5 m/min, feed rate Y-axis: 5 m/min, feed rate Z-axis: 5 m/min, torque: 1,330 Nm, controller manufacturer: Siemens, controller model: Siemens 840D, total height: 5,800 mm, total length: 14,000 mm, total width: 4,000 mm, table width: 2,000 mm, table height: 250 mm, table length: 2,000 mm, table load: 20,000 kg, rotational speed (min.): 2 rpm, rotational speed (max.): 2,500 rpm, overall weight: 40,000 kg, spindle speed (min.): 2 rpm, spindle speed (max.): 2,500 rpm, spindle motor power: 36,000 W, number of slots in tool magazine: 60, input voltage: 380 V, type of input current: AC, Equipment: documentation/manual, rotational speed infinitely variable, The Lazzati HB130 is a heavy-duty CNC horizontal boring and milling machine from the Italian manufacturer Lazzati. Machines of this series are primarily used in large-scale machinery construction, turbine production, energy plant engineering, as well as in tool and mold making. This machine is designed for machining large and heavy workpieces, allowing for precise drilling, milling, and tapping operations on massive steel or cast components. It features a particularly robust construction with hydrostatic guides, ensuring high rigidity and accuracy during heavy-duty machining tasks. Ncodpeytrm Iefx Anisu Spindle taper DIN69871 ISO 50 Milling spindle taper ISO 60 The listed price is exclusive of dismantling, packaging, and shipping. Sale ex location; subject to prior sale. Machines are sold as used; any warranty or guarantee is excluded.