FND Makina

Condition: used, Year of construction: 2004, Used machine Year of manufacture: 2004 with gluing unit for hot-melt adhesive granules Glue reservoir located below the glue roller Glue application to the workpiece via glue roller in both co-rotating and counter-rotating modes automatic edge magazine for coil material and fixed lengths Pressure zone with pneumatically-driven main pressure roller and special post-pressure rollers to compact the upper and lower glue joint Centrally adjustable upper pressure Central manual chain conveyor lubrication Control panel at machine infeed End trimming unit (saw aggregates) for front and rear edge overhang with high-precision linear guides 2 motors, each 0.18 kW Swivel range for straight and bevel cutting 0–15 degrees Flush-milling unit, top and bottom, with vertical and horizontal tracing Swivel range 0–15 degrees with 2 milling motors, each with replaceable insert cutter combinations (straight/radius) Digital counters enable rapid and precise, i.e., repeatable, settings Two-point pneumatic adjustment for upper and lower milling motors Scraper unit for finishing processing with horizontal/vertical tracing Ksdpfx Ajxya Rtsaysdw Support table extendable up to 350 mm Integrated section control for contactless operation of processing functions. Settings via keyboard and LED display Workpiece thickness: 8–50 mm Edge thickness: 0.4–3 mm Feed speed: approx. 9 m/min Connected load: 4.1 kW Compressed air connection: 6 bar Weight: approx. 750 kg Machine length: 3,150 mm Availability: short term Location: Flörsheim

Condition: ready for operation (used), Year of construction: 2007, This CEFLA ROCTRE W was manufactured in 2007. A fully refurbished edgebander, it offers stable performance and reliability, ready for immediate use. Maintaining the original structure's strength, it's ideal for those needing a ready-to-run solution without further restoration. Contact us for more information. Kdedpfxsxyayuo Aayow Application Types Edge Banding

Condition: ready for operation (used), Year of construction: 2010, This BRANDT Highflex 1440 edgebander was manufactured in 2010. Ideal for precise edgebanding applications, it ensures consistent performance for a variety of woodworking tasks. Consider the opportunity to buy this BRANDT Highflex 1440 edgebander. Contact us for more information. Application Types Edge Banding Kdjdexya Avopfx Aayew

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: AH/105752, feed rate X-axis: 18 m/min, workpiece height (max.): 60 mm, control type: PLC-controlled, TECHNICAL DETAILS Panel height: 10–60 mm Solid wood: 15 mm PVC/ABS: 3 mm Feed speed: 12–18 m/min Working height: adjustable via PLC MACHINE DETAILS Kdedpfx Aaexx Nf Djysw Control: PLC EQUIPMENT Adjustable panel support guide Side roller conveyor with idler rollers for panel support Rectifier group Roller holder plate Gluing unit for EVA adhesive with premelter Edge pressing group Trimming group Scribing group with overlapping motors Tiltable copy unit Rounding unit with 4 motors Edge scraper unit Glue scraper unit Oscillating brush group

Condition: used, Year of construction: 2014, Used Machine Single-sided Edge Banding Machine Brandt Optimat KDF 220 C (Ambition 1220 FC) Year of manufacture: 2014 Machine number: 0-261-20-7913 Fixed fence on the right side Infeed fence adjustable manually Feed speed: 11 m/min Max. feed speed with contour trimming: 11 m/min Working height: 950 mm Pneumatic connection: min. 6 bar Workpiece and edging parameters: Minimum workpiece width: - For workpiece thickness 8-22 mm: 70 mm - For workpiece thickness 23-60 mm: 120 mm Workpiece overhang: 38 mm Workpiece thickness: 8 - 60 mm Max. edge height = workpiece height + 5 mm Edge material in roll form: 0.4 - 3 mm Ksdexx D D Uepfx Aayodw Max. edge cross-section: - For PVC: 135 mm² - For veneer: 100 mm² Max. roll diameter: 830 mm Edge material in strip form: 0.4 - 3 mm Max. edge cross-section (strip): 165 mm² Edge thickness up to 6 mm possible by adjusting the pressure zone Equipment configuration: Jointing cutter unit 2 x 2.2 kW 200 Hz (with and against feed) Gluing unit A3 with workpiece pre-heating End trimming unit, chamfer/straight 2 x 0.18 kW Milling unit 2 x 0.27 kW (counter rotation) Contour copying router unit (corner rounding) 1 x 0.35 kW WD 40 Profile scraper with quick-change heads Glue joint scraper 5820 Control system: Easytouch Dimensions: approx. 4280 x 1300 x 1170 mm Weight: approx. 1,400 kg Availability: short notice Location: Flörsheim

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, feed rate X-axis: 14 m/min, workpiece height (max.): 55 mm, controller model: TS 200 Touchscreen, TECHNICAL DETAILS Panel height: 55 mm Solid wood: 8 mm PVC/ABS thickness: 0.4–3 mm Feed speed: 14 m/min MACHINE DETAILS Control: TS 200 touchscreen EQUIPMENT Guide rail for panel insertion Side roller conveyor with idler wheels Kdedpoxxy Hfsfx Aayew Roller holder plate Glue unit for EVA hot-melt adhesive with glue pot Edge pressure group for straight profiles with adjustable pressure rollers End cutting unit with 2 motors and tilt adjustment Fine trimming/trimming unit with 2 tilting motors Corner rounding unit with 2 multifunctional motors (Gleaner + Rounder) Edge scraper group Glue scraper group Brush unit Adjustable working height

Condition: used, Year of construction: 2017, machine/vehicle number: MR005128, Lightly used edge banding machine with gluing unit, end trimming unit, and flush trimming unit. Suitable for edge banding up to 2 mm thickness and panels up to 50 mm thick. Technical specifications: - Minimum edge band thickness: 0.4 mm - Maximum edge band thickness: 2 mm - Minimum panel thickness: 12 mm - Maximum panel thickness: 50 mm - Minimum panel length: 180 mm - Minimum panel width: 65 mm - Feed speed: 6 m/min - Glue reservoir capacity: 0.5 kg - Pre-milling unit: No - End trimming unit: Guillotine knife - Serial number: KK /138932 Kedpfexxx Diox Aaysdw

Condition: new, Year of construction: 2025, The new SICAR ECO F7 edgebander model distinguishes itself from other compact edgebanders because all functional modules of the Eco F series are derived and suitably modified from the industrial edgebanders. Although it possesses the same high precision and stability as industrial machines, it retains maximum durability and processing efficiency. The Eco F series saves space and ensures excellent edge-banding quality. It is the ideal choice for small furniture factories, decorators, and joinery workshops; it is also extremely useful for small-batch production in large furniture factories. Equipment includes: – Infrared heating lamp – Glue scraper – Meter counter – Cleaning fluid – Separating agent Total power: 10.3 kW Calibrating motor power: 1.8 kW*2 Glue application motor power: 0.75 kW Heater power: 1.5 kW Cutting motor power (end trim saw): 0.37 kW*2 Trimming motor power: 0.75 kW*2 Polishing motor power: 0.37 kW*2 Conveyor motor power: 1.5 kW Working speed: 8-11-13 m/min Max. edge band height: 45 mm Panel thickness: 10-45 mm Kdjdpfx Ajxxxiloaysw Edge band thickness: 0.4-3 mm Min. panel width: 80 mm Working air pressure: 0.6-0.8 MPa Machine dimensions: 4580x700x1300 mm Packing dimensions: 4280x650x1280 mm Net/gross weight: 1000/1230 kg 12-month warranty Transport and installation provided within Serbia

Condition: new, feed rate X-axis: 7 m/min, workpiece height (max.): 50 mm, type of input current: three-phase, input voltage: 400 V, With corner copying, suitable for plastic edges from 0.4 - 3 mm, solid wood edges up to 3 mm, and workpieces from 8 - 50 mm, with pneumatic adjustment. Panel thickness: 8 – 50 mm Edge thickness: 0.4-3 mm (coil material) Jointing unit: Yes Radius milling unit: Yes Corner copying unit: Yes Scraper: Yes Buffing unit: Yes Premium equipment for high productivity with minimal space requirements! Intuitive operation with eye-S control and 10" large touchscreen: HMI Maestro Active Edge; graphical representation of all processing units and their operating status; graphical simulation of operations; control of all processing units; regulation of glue pot temperature; assistant functions for machine setup according to the processing program; error diagnosis for quick resolution of simple faults; statistics on processing parameters; USB connection; network connectivity ready; prepared for Industry 4.0 with API REST data transfer protocol. Outstanding accessibility to work units thanks to the large hood, which also provides protection and noise reduction Monoblock steel construction ensures high stability and rigidity of the machine Automatic unit positioning when changing panel thickness Cut-off saw unit with corner rounding (me 35 tr s): for trimming the edge and rounding corners on the top and bottom; for edging solid wood, trimming is done with the radius milling cutter; high-frequency motor with 12,000 rpm; saw blade Ø125mm Z12 Panel feed via feed chain with rubber sliding shoes Extendable workpiece support Adjustment of infeed fence via spacer plates Dimensions and Weights Length (product) approx. 3314mm Width/depth (product) approx. 1085mm Height (product) approx. 1300mm Weight (net) approx. 623kg Flush radius milling unit Rated output: 2 x 0.35kW Cutter diameter: HW55.3mm Spindle speed: 12000min⁻¹ Extraction port diameter: 60mm Number of extraction ports: 2 Corner copying unit Rated output: 0.35kW Tool diameter: 58mm Speed: 12000min⁻¹ Electrical data Connection voltage: 400V Mains frequency: 50Hz Glue unit Glue pot rated output: 0.25kW Glue pot operating temperature: 190°C Glue pot extraction port diameter: 60mm Glue pot capacity: 0.8kg Pneumatic connection Operating pressure: 6.5bar Air consumption: 470l/min Feed Feed rated output: 0.55kW Feed speed: 7m/min Kodjxxvanspfx Aayedw Edges Edge thickness (coil material): 0.4 – 3.0mm Pre-milling unit Extraction port diameter: 2 x 80mm Rated output: 3kW Cutter speed: 7200min⁻¹ Diamond cutter diameter: 80mm Cutter height: 56mm Material removal: 0.5 / 1 / 1.5 / 2mm Scraper units Radius scraper: 2mm Buffing unit Rated output: 2 x 0.14kW Speed: 2800min⁻¹ Workpiece Workpiece thickness: 8 – 50mm Minimum workpiece length: 120mm Minimum workpiece width: 110mm

Condition: new, Year of construction: 2023, functionality: fully functional, total length: 3,774 mm, edge thickness (max.): 3 mm, overall weight: 842 kg, plate height: 50 mm, For plastic edges from 0.4 - 3 mm, solid wood edges up to 5 mm, and workpieces from 8 - 50 mm. Panel thickness: 8 – 50 mm Edge thickness: 0.4-3 mm (coil material) Jointing unit: Yes Radius milling unit: Yes Scraper: Yes Buffing unit: Yes Top configuration for high productivity in a compact footprint! Intuitive operation with the eye-S control and 10” large touchscreen: HMI Maestro Active Edge Graphic display of all processing units and their operating status Graphical simulation of machining operations Control of all processing units Regulation of glue pot temperature Assistance functions for machine setup according to the machining program Error diagnostics for rapid troubleshooting of simple issues Statistics on machining parameters USB port Prepared for network connection Excellent accessibility to working units thanks to the large hood, ensuring protection and noise reduction Automatic positioning of units when changing panel thickness Panel feed via chain conveyor with rubber slip shoes Quality made in Italy Equipment details 10" touchscreen control panel Optimum machine management with the new 10" touchscreen control panel featuring Maestro Active Edge, visually representing all machine functions Pre-milling unit Two diamond-tipped cutters Glue station Glue is quickly and evenly heated by heating rods located in both the glue pot and the glue application roller Automatic temperature reduction during prolonged machine idle times Teflon-coated glue pot for easy glue changes Device for reusing unused glue Automatic application of edge banding from coils with cut-off knife for edges up to 3 mm Rotary table with Ø 730 mm Self-lubrication of the glue pot Quick-change kit for the glue pot Flush/radius milling unit With horizontal and vertical tracing rollers for optimal tool positioning Equipped with combination milling tool Ø 55.3 mm for flush milling of edges up to 5 mm and radius edges up to 2 mm Precise adjustment via 2 digital displays With chip extraction Surface scraper Absolute cleanliness for perfect finishing of the workpiece surface With rotating copying device Buffing unit Powered by two independently swiveling and height-adjustable motors Kjdexxuvbepfx Aayjdw For perfect cleaning and polishing of panel edges Profile scraper With digital position display For perfect finishing of plastic edges With device to retract the unit when it is not needed Edge magazine For automatic application of strip edges Solid wood strip edges are automatically loaded and synchronized with the panel feed

Condition: ready for operation (used), Year of construction: 2010, General Data Measurements depth 7845 mm Machine weight 5000 kg Additional Equipment HOMAG gluing and finishing components Kdedpfxsxxndlj Aaysw This HOMAG KAL 210 AMBITION 2264 edgebander was manufactured in 2010. It features a max glued edge thickness of 20 mm, edge gluing height up to 60 mm, and a max feed speed of 25 m/min. Equipped with a granulate glue system, preheating zone, and various processing units including a joint trimming and corner rounding unit. Consider the opportunity to buy this HOMAG KAL 210 AMBITION 2264 edgebander. Contact us for more information about this machine. Application Types Edge Banding

Condition: excellent (used), SCM Casadei Flex 17 Edge Banding Machine, similar to SCM K100 - Pre-milling cutters - Glue application with roller - Pneumatic pre-cut guillotine - Pressure rollers - Final trimming saw - Top-and-bottom milling unit R1 – R2 - Flat scraper - Machine length: 320 cm - Feed rate: 7 m/min Kodpfx Asxxlunoayedw - Max workpiece height: 50 mm - Max edge thickness: 3 mm - Used machine, in very good condition - Total length processed: only 15,250 meters Possibility to inspect before purchase.

Condition: excellent (used), Biesse Stream 5.5 A Edgebander Kdedpfx Ajxxlqvjayew Mileage: 246,000 m Top pressure belt, fluids Pre-milling cutters, Glue application, Pre-melter for PUR adhesive The glue pot is equipped with a glue drain Pneumatic pre-cut guillotine, Pressure rollers fluids Flush trim saws, Top and bottom trimming unit with straight cutters Top and bottom multi-cutter trimming unit Two corner rounding units Fluids Profile scraper (multi R1-R2), Cleaning fluids Flat scraper, Polishing unit, The machine is equipped with NC control for routers and a pneumatic package, Max workpiece height 60 mm, Max edge banding thickness in roll: 3 mm, Feed rate: 12, 18 and up to 20 m/min The machine is in very good condition.

Condition: excellent (used), operating hours: 93 h, Catalogue number 7814 Only 93 hours worked, 5,667 meters processed TECHNICAL DATA Equipment: - Disc Kdjdpfoxxla Rex Aayow - Pre-milling - Tape feeder - Glue tank (cartridges) - Guillotine – pre-cutting of edging tape - 3 pressure rollers - 2 trimming units with saw blades for final edge trimming - 2 milling units for edge profiling (radius cutters) - Corner rounding unit - Scraper units for removing excess glue - Polishing units - Workpiece thickness: 6–45 mm - Minimum workpiece length: 180 mm - Minimum workpiece width: 60 mm - Edging thickness from roll: 0.4–3 mm - Air requirement: 6–8 bar - Extraction ports: 1×60 mm, 4×80 mm, 1×120 mm - Dimensions (L×W×H): 5,900×950×1,850 mm - Weight: 1,720 kg ADVANTAGES – German-made – Spray system – Pre-milling and corner rounding – Original paint (not repainted) – Very good condition, only 93 hours worked, 5,667 meters processed – Used edge banding machine Net price: PLN 56,900 Net price: EUR 13,550 (based on 4.2 EUR exchange rate) (Prices may vary with significant exchange rate fluctuations)

Condition: ready for operation (used), Year of construction: 2022, Additional Equipment Control Panel: Smartouch 21" Control System: E-motion // control system with motorized adjustment (accuracy 0.01 mm) Chain Feed System: With automatic lubrication Top Pressure Beam: Motorized height adjustment Pre-milling Unit: 2 x 2.2 kW motors, diamond cutters, up to 3 mm removal Glue Application System: Compatible with EVA and PUR, fast heat-up (8 min) Additional Glue Tank: For fast glue change Edge Pressure Unit: 1 driven + 2 passive rollers, pneumatic control Trimming Unit: 2 motors (0.5 kW), adjustable 0–15° Multi-functional Trimming Unit: 2 motors, 0.75 kW, top and bottom Kjdpfx Aasxxdutjyodw Corner Rounding Unit: Edge thickness 0.4 – 3 mm, panel height 10 – 60 mm, 2 independent motors, 12000 rpm This FORMAT4 Tempora F800 60.12/2 E edgebander was manufactured in 2022. It features a Smartouch 21" control panel, E-motion control system, and a chain feed system with automatic lubrication. The machine includes a pre-milling unit with diamond cutters and a glue application system compatible with EVA and PUR. Consider the opportunity to buy this FORMAT4 Tempora F800 60.12/2 E edgebander. Contact us for more information. Application Types Edge Banding

Condition: ready for operation (used), Year of construction: 2022, General Data Measurements height 1445 mm Dimensions Machine Length 2740 mm This CASADEI Bordatrice E350PM was manufactured in 2022. It features a panel height range of 10-45 mm and supports edge band thickness from 0.4 to 2 mm. The machine operates at a feed belt speed of 7 m/min, with a glue pot heating power of 1490 W. Consider the opportunity to buy this CASADEI Bordatrice E350PM edgebander. Contact us for more information. Kodpfjxxdtpsx Aayedw Application Types Edge Banding

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, feed rate X-axis: 20 m/min, workpiece height (max.): 60 mm, edge thickness (max.): 12 mm, Equipment: CE marking, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Kedpsxxaucjfx Aaysdw Max. feed speed: 20 m/min Panel height min.: 8 mm Panel height max.: 60 mm Panel length min.: 150 mm Panel width min.: 65 mm Edge thickness min.: 0.3 mm Edge thickness max.: 12 mm Pre-cutting unit Unit: Corrections Edge pre-heating lamps Glue application system Glue pot for polyurethane adhesive Pre-melter for polyurethane adhesive Edge pressure roller track Number of pressure rollers: 6 End trimming unit Model: 08.415 Number of motors: 2 Motor power: 0.66 kW Max. speed: 12,000 rpm Top/bottom trimming unit Model: 08.0555 Number of motors: 2 Motor power: 1 kW Multifunctional unit Model: SKF-L Number of motors: 4 Max. machining speed: 20 m/min Motor power: 0.18 + 0.400 kW Speed: 12,000 rpm Edge scraping unit Model: 08.519 Glue scraping unit Model: 08.521 Buffing unit Model: 08.617-2 Number of motors: 2 Motor power: 0.18 kW MACHINE DETAILS Number of operating units: 8 Adhesive system: PUR Control system: WINDOWS EQUIPMENT Programming software for the machine: ICOS open TS CE marking

Condition: excellent (used), Edge banding machine Artech Akron 420 Glue application by roller, Pneumatic pre-cut guillotine, Pressure rollers, Finishing trim saws, Milling units R1, R2, Profile scraper, Kdedpfx Aexw Uzzjayjw Condition: very good

Condition: ready for operation (used), Year of construction: 2014, functionality: fully functional, workpiece height (max.): 60 mm, edge thickness (max.): 3 mm, workpiece width (max.): 1,300 mm, workpiece length (max.): 3,200 mm, Equipment: CE marking, TECHNICAL DETAILS Max. feed speed: 24 m/min Maximum panel thickness: 60 mm Minimum panel height: 10 mm Maximum panel height: 60 mm Minimum panel length: 320 mm Maximum panel length: 3,200 mm Minimum panel width: 150 mm Maximum panel width: 1,300 mm Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Number of working units: 8 UNITS Trimming Unit 1 Function: Sizing Model: RT30 Motor Power: 3.5 kW Max. speed: 9,000 rpm Edge Processing Unit 1 Function: End Trimming Model: IT90-S Number of motors: 2 Max. processing speed: 28 m/min Motor power: 0.65 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Function: Edge Milling Model: RF10 Number of motors: 2 Motor power: 1 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Function: Multifunction Model: AR30 Number of motors: 2 Max. processing speed: 18 m/min Motor power: 0.65 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Function: Profile Scraper Model: RB40 Edge Processing Unit 5 Function: Glue Scraper Model: RC20 Edge Processing Unit 6 Function: Brushing Model: SZ30 Number of motors: 2 Kdjdpfx Aaexw T Tpsyjw Motor power: 0.37 kW Max. speed: 1,400 rpm MACHINE DETAILS Installed total power: 25 kW Dimensions Conveyor length: 12,300 mm Width: 1,300 mm Length: 12,300 mm EQUIPMENT Jointing cutters Multifunction unit Top pressure Pressure via rubberised belts Panel support guide NC positioning Angled panel infeed system Automatic engagement by time Edge preheating lamps Coil magazine Hot-melt glue pot Hot-melt glue pre-fuser Edge pressure roller conveyor Spray unit SINTRA machine programming software Panel discharge via roller transfer conveyor Panel feed via motorised carpet belt Return system for left-side edge bander CE marking

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, pre-milling unit granulate glue station pneumatic pre-cut guillotine precision saws for trimming workpiece ends milling unit with profile cutters corner milling unit profile scraper unit straight scraper unit machine length 4500 mm Kodpsxw T Tisfx Aayodw Year of manufacture 2013 Total feed – 87026 linear meters

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, feed rate X-axis: 25 m/min, edge thickness (max.): 3 mm, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed rate: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool change with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Kdedsxw T H Njpfx Aayjw Edge Processing Unit 4 Unit: Top Router Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spraying unit Machine programming software PowerControl PC22 CE marking

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, workpiece height (max.): 50 mm, edge thickness (max.): 3 mm, rotational speed (max.): 10,960 rpm, Equipment: CE marking, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Maximum panel thickness: 50 mm Minimum panel height: 8 mm Maximum panel height: 50 mm Minimum edge thickness: 0.4 mm Maximum edge thickness: 3 mm Number of positions: 1 Unit 1 Unit: End trimming Number of motors: 2 Automatic engagement by time: yes Motor power: 0.18 kW Speed: 10,800 rpm Unit 2 Unit: Edge milling Number of motors: 2 Automatic engagement by time: yes Motor power: 0.27 kW Speed: 10,960 rpm Unit 3 Unit: Edge scraper Control system: BFS MACHINE DETAILS Installed total power: 4 kW EQUIPMENT Upper pressure Pressure by spring-loaded rollers Panel support guide Magazine for the coil EVA glue system Hot-melt glue pot Kedpfx Aoxw Tugoaysdw Edge pressure roller track Number of pressure rollers: 3 CE marking

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, feed rate X-axis: 11 m/min, workpiece height (max.): 40 mm, edge thickness (max.): 6 mm, rotational speed (max.): 12,000 rpm, Equipment: CE marking, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Max. feed speed: 11 m/min Maximum panel thickness: 40 mm Min. panel height: 8 mm Max. panel height: 40 mm Min. edge thickness: 0.3 mm Max. edge thickness: 6 mm Maximum spindle speed: 12,000 rpm MACHINE DETAILS Trimming unit Unit: Format cutting Unit: Trimming Automatic engagement by time Motor power: 2.2 kW Edge heating lamps Coil magazine Number of positions: 1 Gluing system Hot melt glue pot Edge pressure roller conveyor Number of pressure rollers: 3 Edge processing unit 1 Unit: End trimming Number of motors: 2 Automatic engagement by time Motor power: 0.18 kW Maximum speed: 12,000 rpm Edge processing unit 2 Unit: Top/bottom trimming Number of motors: 2 Motor power: 0.27 kW Maximum speed: 12,000 rpm Edge processing unit 3 Unit: Multifunction Number of motors: 1 Motor power: 0.35 kW Maximum speed: 12,000 rpm Edge processing unit 4 Unit: Scraper Edge processing unit 5 Unit: Buffing Number of motors: 2 Motor power: 0.1 kW Total installed power: 13 kW Kdedoxw Ttvjpfx Aaysw EQUIPMENT Control system: PC 16 CE marking

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, feed rate X-axis: 11 m/min, edge thickness (max.): 3 mm, plate height: 60 mm, rotational speed (max.): 12,000 rpm, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Maximum feed speed: 11 m/min Maximum panel thickness: 60 mm Minimum panel height: 8 mm Maximum panel height: 60 mm Minimum panel width: 70 mm Minimum edge thickness: 0.4 mm Maximum edge thickness: 3 mm Number of working units: 5 Maximum rotation speed: 12,000 rpm MACHINE DETAILS Unit: Pre-trimming unit Unit: Finishing/Adjustment unit Automatic engagement by time: yes Motor power: 2.2 kW Edge pre-heating lamps Coil magazine Number of positions: 1 Adhesive system Glue pot for hot-melt glue Prefuser for hot-melt glue Edge pressure roller track Number of pressure rollers: 3 with NC positioning Kodpfxsxw Tnge Aaysdw Edge processing unit 1 Unit: End trimming unit Number of motors: 2 Maximum processing speed: 11 m/min Motor power: 0.18 kW Maximum rotation speed: 12,000 rpm Edge processing unit 2 Unit: Edge milling unit Number of motors: 2 with NC positioning Motor power: 0.55 kW Maximum rotation speed: 12,000 rpm Edge processing unit 3 Unit: Edge scraper Edge processing unit 4 Unit: Glue scraper Total installed power: 13 kW EQUIPMENT Control system: EASY CONTROL EC 10+ CE marking

Condition: excellent (used), Year of construction: 2019, operating hours: 1,200 h, functionality: fully functional, machine/vehicle number: 0261973988, Equipment: ABS, type plate available, Year of manufacture: 2019 Equipment and technical data: Processing dimensions Workpiece thickness: 8–60 mm Workpiece width: from 70 mm Edgeband height: up to 8 mm Edgeband thickness (coil material): up to 3 mm Feed Speed adjustable from 8 to 14 m/min, stepless adjustment Gluing technology Gluing system for granulate Glue tank below the feed zone Interchangeable HOMAG glue tank Suitable for EVA and PUR processing Quick-change function Kedexw Nwkopfx Aayodw Units Milling unit Preheating zone Pressure station Flush/radius/chamfer trimming station Scrapers: profile and flat Additional equipment and operation PU pressure rollers HOMAG powerTouch control panel Right-hand machine version CE compliant Dimensions: approx. 3900 x 950 x 1,150 mm Weight: approx. 2,000 kg Availability: immediately