Maruthi Fabtech

Year of construction: 1989, condition: used, Used machine Year of manufacture: 1989 Technical specifications: 4-spindle drilling head with press-in bracket, pitch: 52/5.5/32 mm 7-spindle drilling head with 32 mm pitch and locating pin Including drilling depth adjustment Including stop extensions Including folding stops Connection: 380 V Dimensions: 550 x 750 x 790 mm without stops Location: Hochheim Gbjdpfx Aoxavraefpeu Availability: Immediately

Year of construction: 2025, condition: new, New machine Gjdpow Nafksfx Afpjbu Year of manufacture: 2025 Features and technical specifications: Fully equipped in standard version with: - Robust, torsion-free steel frame, welded and bolted construction - Lamella pressure beam TOP with 6 elements, lamella pressure beam SIDE with 5 elements - Lamella pressure beams with proven tolerance compensation system (Ganner system) for tightly compressed carcass joints - Counter-pressure surfaces (side pressure wall, base) are 38 mm thick, coated, continuous support plates - Continuous pressing surface, height 95 mm, on lower vertical pressure beam - Electromechanical adjustment of both pressure beams via precision trapezoidal thread spindles (with increased lead and concentricity accuracy) and high-performance ball nuts with grease reservoir - The pressing process is carried out electromotorically, via 2 independent worm gear motors (2 x 0.75 kW) - Pressing force of the pressure beams is infinitely variable and electronically controlled by 2 potentiometers, regulated via frequency inverter, ensuring absolutely wear-free force control - Pressing force for horizontal pressure beam: min. 500 daN (kg), infinitely adjustable up to max. 2200 daN (kg) - Pressing force for vertical pressure beam: min. 300 daN (kg), infinitely adjustable up to max. 2200 daN (kg) - Pressing and adjustment speed of the beams with fine positioning, using 3-stage selector switch: 5 / 10 / 25 mm/second - Jog mode for precise positioning of both pressure beams, e.g. for low pressing forces, drawers, and carcasses at 45° - Simplest operation via 6 separate push buttons, 8 movement cycles selectable via control panel - Freely adjustable press time preselection 0-30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressure beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 300 mm - Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm Including surcharge for rapid traverse speed, for fast positioning of the pressure beams, controlled via automatic workpiece detection with sensors in the pressure beams, pressing speeds 5 / 10 / 25 mm/sec and rapid traverse speed 50 mm/sec, the sensors can be deactivated for pressing special components Including a set of machine feet for 500 mm working height Location: Flörsheim Availability: Short-term

Year of construction: 2025, condition: new, New machine Year of manufacture: 2025 Features and technical data: Standard configuration: - Robust machine base - Dowel system for: Dowel diameter 8 mm, Dowel length 35 mm (factory setting, adjustable from 30 to 40 mm), Dowel protrusion 12 mm (factory setting, adjustable from 7 to 20 mm) - Recoil-free gun - Vibratory feeder for dowel transport - Dowel diameter and length control with Auto-DL-Select system - Water supply system for pre-glued dowels - Water tank (stainless steel, 7.5 l) - Closed water system with 6 bar water pressure and spray nozzle - Electronic control with: - Main switch On / Off - Program selector switch Water / Water + Feeding - Potentiometer for dowel feed via vibratory feeder - Potentiometer for adjusting water injection quantity - Control lamp for indicating minimum water level in the water tank - Mobile base - Compressed air: 6 bar / Electrical: 230V, 1Ph, 50Hz HoKuTech DübelJet with option for opposing hole processing: 1 unit HoKuTech | DübelJet with upgrade kit for LeimJet including fixtures for attaching/connecting to the DübelJet including height-adjustable suspension for glue hose including: 1 HoKuTech | LeimJet Glue dispensing unit for opposing hole processing Viscosity for PVAc glues up to 75,000 mPas Includes dowel nozzle for Ø 8 mm, pointed nozzle Godpfxewx Aadj Afpobu Location: Flörsheim Availability: Immediately

Year of construction: 2025, condition: new, New machine Year of manufacture: 2025 • Robust, space-saving double wide-belt sander for the highest demands • Consistent working height thanks to upper frame adjustment • Working width: 1350 mm • Maximum passage height: 205 mm (with up to 18.5 kW main drive motor) • Sanding belt dimensions: 1350 x 2000 mm 1st Unit “R” Contact Roller • Grooved rubber contact roller, hardness 80 Sh • Contact roller height infinitely adjustable via touch screen • Motorized lifting/lowering of the contact roller according to unit selection 2nd Unit “Ed-L” Diagonal Sanding Pad • Entire sanding unit adjustable by 10° • Electronic sanding pad with 22 mm segment width (pivoting special design), variable edge pressure, automatic pressure regulation, and storage of sanding pad segments • Infinitely variable sanding belt speed (with PLC memory)* • Additional sanding pad insert • Main Motors • 1st unit: 18.5 kW (25 HP) / 400 V/50 Hz • 2nd unit: 11 kW (15 HP) / 400 V/50 Hz • Workpiece Feed • Fabric-reinforced rubber conveyor belt • Rubberized conveyor drive roller • Motor: 2.2 kW (3 HP) / 400 V/50 Hz • Speed: infinitely variable 3 – 15 m/min • Vacuum Device • Located on the feed table • Additional perforation of the conveyor belt over 200 mm • Vacuum generator: 2.2 kW (3 HP) / 400 V/50 Hz • Sanding Belt Cleaning • Air knife for cleaning the sanding belt of the 2nd “Ed-L” unit, operation-controlled, with extraction channels, powered by vacuum generator using vacuum return air from the vacuum table, including diverter valves • Pressure Elements • Infeed: parallel spring-loaded, ground steel pressure roller Ø 50 mm • Between units: rubberized pressure roller Ø 50 mm • Outfeed: rubberized pressure roller Ø 50 mm • Basic Equipment • Motorized, finely adjustable height setting with digital display • Pneumatic belt tensioning, control and oscillation; compressed air consumption approx. 4 l/min • Optimum safety with automatic immediate stop with disc brake in case of belt breakage, etc. • Complete electrical system with contactor control; automatic star-delta starting for the main motor, motor protection, and ammeter for monitoring material removal • Automatic thickness adjustment across the entire working width • Workpiece over-thickness protection with immediate feed stop and automatic lift • Electronic compensation for sanding belt grit • Stepless chip removal adjustment • Electronic feed speed control at the operator panel, infinitely adjustable 3 – 15 m/min • PLC control/programming with color touch screen and TEACH-IN memory (push-button according to sanding result, no manual input required) • Pneumatic conveyor belt tracking control • Workpiece support roller at infeed and outfeed • ENORMATIC: fully automated rapid setup and feed activation • eco*-energy saving mode • Fault diagnosis • Job and operating hour counters, square meter counting and visualization of belt wear • High-quality, swiveling Plexiglas control panel with LAN and USB connection • 10’’ touch screen with Industry 4.0 control • Preparation for extraction flap control for each unit Machine ready for operation in INTERMEDIATE LACQUER SANDING version (1350-REd-L) Additional 'INTERMEDIATE LACQUER SANDING' features on 2nd unit: Gedpjwt E Utefx Afpebu ?

Year of construction: 1971, condition: used, machine/vehicle number: 37919, Tischbohrmaschine / Drilling machine IXION BST 13 Baujahr / Year 1971 - Serial-No. 37919 Technical Details: Abmessungen / Dimensions 220 x 400 x 820mm Gewicht / Weight 50kgs Online-Video-Inspection by Skype-Video Gjdpfx Afjupy Ttopobu We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Bagger Minibagger Online-Video-Inspection by Skype-Video Gbjdpfx Aet Drmhofpeu We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, machine/vehicle number: 19013, Combined copying milling machine - lathe MICHÄL KÄMPF Online-Video-Inspection by Skype-Video Gbedpfeh Axryjx Afpsu We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Year of construction: 1982, condition: used, Turning machine Schaerer , model UD632 Arbeitshhe ber Flur : 1120 mm Spitzenhhe ber Flachbahn : 320 mm Umlauf ber Bett : 660 mm Umlauf ber Planschlitten kurz : 450 mm Umlauf ber Planschlitten land : 420 mm Umlauf ber Aussparung : 710 mm Antriebsleistung : 15 22 kW Drehmoment a.d. Arbeitsspindel : 3000 Nm Max. Rack weight between spindles without stock : 1500 kg Max. Max. werkstckgewicht zwischen den S. mit einem Setzstock : 2200 kg Bettbreite : 460 mm Spindle working head with Zentrierkegel : 55022 , gr. 8 Spindle in forward bearing : 120 mm Spindelbohrung, durchgehend : 72 mm Vorn Kegel 1:20 : 80 mm Inner cone : Morse 5 Drehzahlen : 1,8 2240 1/min Bettschlitten Vorschbe Anzahl : 3 x 32 Lngs bereich A 1:1 : 0,07 1,12 mm/U Lngs bereich B 4:1 : 0.31 4.5 mm/U Lngs bereich C 24:1 : 1.8 28 mm/U Plan bereich A 1:1 : 0.035 0.56 mm/U Plan bereich B 4:1 : 0.16 2.24 mm/U Plan bereich C 24:1 : 0.9 14 mm/U Eilgang lngs : 5000 mm/min Eilgang plan : 2500 mm/min Leitspindel Steigung : 12 mm Leitspindel Durchmesser : 50 mm Gewinde metrisch Anzahl : 3 x 32 Gewinde metrisch Bereich A : 1 12 mm Gewinde metrisch Bereich B : 3.25 48 mm Gewinde metrisch Bereich C : 21 288 mm Gewinde Zoll Bereich A : 24 15/8 Gg/mm Gewinde Zoll Bereich B : 6 Gg/mm Gewinde Zoll Bereich C : 1 1/12 Gg/mm Gewinde Modul Bereich A : 0,5 6 Mod Gewinde Modul Bereich B : 2 24 Mod Gewinde Modul Bereich C : 10,5 144 Mod Gewinde DP Bereich A : 48 3 Gg/Mod Gew Gbjdpfsgbd E Dex Afpsu

Year of construction: 2003, condition: used, Pbt 25 pc 200 obtained by trade-in Gedpfx Afof Rih Depebu Machine's really in new condition! Hour counter is at 622 hours!!!   the picture&#39,s say enough. , JWV Service is an importer for the Netherlands and Belgium of PBT profile rolling machines and dealer of Meba band saw machines, Faccin plate rolling machines and various other brands. The team of JWV Service has 25 years of experience in troubleshooting and overhauling metalworking machines. Look up for more machines.

Year of construction: 2016, condition: used, Various aluminium sawing machines in stock Gbedof Rihvopfx Afpou