Control card

Homag 2

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Kdedpfjyqybuox Agdsi Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Kodpjyqx U Hjfx Agdodi Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Mill Model: UF11 Kdsdpfx Aeytr Hbsgdoi Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: used, machine/vehicle number: 008107, undefinedPosition 2: Panel Return Systems HOMAG + LIGMATECH-KAR 310/9/A20/S2 Kodpfx Asw U Rqzsgdodi

Condition: excellent (used), Year of construction: 2001, machine/vehicle number: 0-200-24-6287, functionality: fully functional, input voltage: 400 V, input current: 56 A, edge thickness (max.): 20 mm, Equipment: CE marking, Used single-sided HOMAG edge-banding machine for straight edges – KL 78/A20/S2 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2001 Kdodpoyv Da Hofx Agdji SPEZIFICATION & EQUIPMENT: Basic machine with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness max. 60 mm - top pressure with compound V-belt, motorized height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - clamping of glue application unit before rear end of workpiece, for even glue application - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clock-wise, counter clock-wise), 2x4kW, jumping function GLUING SECTION A20, consisting of: - QA34 glue application unit, on request with PTFE-coating (Teflon) - Pre-melter for EVA glues - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 6 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit HL81, 2 motors, with straight/chamfer cutting function motorised fine-positioning of snipping stop - Pre-milling (rough trimming) 1,5 kW, top/bottom - Corner rounding FK13, 2 motors (top/bottom) with automatic 8-fold tool changer and several exchangeable trimming heads - Profile (radius-) scraping MN21, with NC-axis positioning - Flat scraping (glue joint) FA10, top/bottom, (version with 3 tracer rollers) - Straight belt sanding unit KS10 - Buffing unit top/bottom ELECTRONIC CONTROL: - HOMATIC NC21 OPERATING SYSTEM

Condition: good (used), Year of construction: 2005, Gluing unit Motorized height adjustment Homatic NC 21 control unit Frequency converter A20 hot melt adhesive unit for roll material up to 3 mm and strip material up to 20 mm edge thickness End trimming unit (two motors) Feed control LCD flat panel display Feed rate 18.5 m / min ? Feed rate steplessly adjustable 8–24 m/min or 12–24 m/min Minimum working width 55 mm at workpiece thickness 22 mm / 100 mm at workpiece thickness 60 mm depending on workpiece length Workpiece projection 30 mm Workpiece thickness 12–60 mm Workpiece thickness without contour milling and finishing unit min. 8 mm Jointing/milling unit Workpiece preheating A 20 gluing unit / A 34 hot melt adhesive unit Magazine for solid wood edging, strip material, and roll material Roll cutting device Pressure zone KL end trimming unit Release agent spraying device top/bottom Melting unit with granulate hopper instead of glue pot QA glue pot front section, quick-change (for color changes) Pre-milling unit Contour milling unit with interchangeable heads Universal milling unit Automatic multi-trimming unit, complete Finishing unit The illustrated return unit is not included in the scope of delivery. Kjdpjyvy D Iofx Agdedi The data were taken from a data sheet and are therefore supplied without guarantee. Exact configuration on request.

Condition: used, Year of construction: 2007, total height: 1,200 mm, total length: 3,600 mm, total width: 1,480 mm, - Machine available from: 2025-12-15 - Year: 2007 - Documentation available: Yes - └ Type Documentation: Technical data, Electrical diagrams, User manual, Operating system - └ Language: NL - CE marking present: Yes - CE certificate present: No - Serial number: - Number of units [pcs]: 8 - └ 1st unit type: - - Tools available: Yes - └ 3rd unit type: - - Tools available: Yes - └ 4th unit type: - - Tools available: Yes Kjdpox Ei Syofx Agdedi - └ 5th unit type: - - Tools available: Yes - └ 6th unit type: - - Tools available: Yes - └ 7th unit type: - - Tools available: Yes - Voltage [V]: 400 - Current consumption [A]: 50 - Transport dimensions: 3600mm x 1480mm x 1200mm (l x w x h) - Transport packages [pcs.]: 4 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: ready for operation (used), Year of construction: 2009, Edgebander manufactured in 2009. This HOMAG PROFI KAR310/11/A20/S2 features a work piece return system BARBARIC. Consider the opportunity to buy this HOMAG PROFI KAR310/11/A20/S2 edgebander. Contact us for further details. • Condition: Used Kdsdpfx Aoyhqi Dogdei Additional equipment • BARBARIC workpiece return system

Condition: ready for operation (used), Year of construction: 2009, This HOMAG KAL 330/6/A3/S2 was manufactured in 2009. A used edgebander featuring a gluing unit for EVA hot melt adhesive, pressure zone, cutting unit, copy milling, scrapers, and a buffing unit. Includes a LIGMATECH workpiece returning system. Consider the opportunity to buy this HOMAG KAL 330/6/A3/S2 edgebander. Contact us for more information. • Configuration/Features: • Joining milling Kedjychduspfx Agdodi • Gluing unit for EVA hot melt adhesive • Pressure zone • Cutting unit • Copy milling • Scrapers • Buffing unit Additional equipment • Workpiece returning system: LIGMATECH

Condition: used, functionality: unexamined, Ferwood Code: RU0010622 - Manufacturer Code: 2-083-01-0276 - Condition: Used - Functionality: Not tested - Compatible Machine: - Weight: 3KG - Dimensions: 36X26X21 cm - If interested, we offer a refurbishment service. Please contact us. Kdjdpfxsyrq Ale Agdei