Cylindrical grinding machine

KELLENBERGER 600U

Condition: used, Year of construction: 2000, Kellenberger 600 U cylindrical grinding machine Condition: Used Year of manufacture: 2000 Technical data: Table: Distance between centers: 600 mm Travel: 900 mm Travel per handwheel revolution, coarse/fine: 20 / 2.5 mm Travel per division on the handwheel: 0.05 mm Speed, hydraulically continuously variable: 0.02 - 6 m/min Reversal travel, minimum: 2.5 mm Dwell time during reversal, continuously variable: 0 - 5 sec Swiveling range: 11 degrees Cross slide: Travel with feed handwheel in fine or coarse mode: 220 mm Travel per handwheel revolution, coarse/fine: 8 / 1 mm/ø Division on the handwheel: 5 µm/ø Hedpfx Aey T E Rzshzenp Division with micrometer adjustment: 1 µm/ø Rapid traverse, hydraulically: 40 mm Feed, hydraulically: 0.95 mm/ø Form grinding: Feed rate: 0.25 - 25 µm/sec Surface grinding: Feed increments per table reversal: 130 µm/ø Grinding spindle head: Grinding wheel for external cylindrical grinding: 400 x 50 x 127 mm

Condition: excellent (used), KELLENBERGER PRECISION UNIVERSAL CYLINDRICAL GRINDING MACHINE TYPE: 600 U YEAR OF MANUFACTURE: 2003 PARTIAL OVERHAUL: 2026 (Technical data see attached documents) Center height: 175 mm (without height adjustment) Grinding length: 600 mm Equipment: - Standard accessories - Internal grinding device for D: 80 mm max. incl. coolant supply through the workpiece spindle - Grinding wheel equipment left for D: 400 x 50 x 127 mm (standard) - Grinding wheel equipment right for D: 300 x 40 x 127 - Grinding wheel flange for wheels D: 400 x 50 x 127 mm (left) and D: 300 x 40 x 127 (right), balancing weights outside (3 pieces left, 2 pieces right) - Variable spindle drive with Danfoss frequency converter - Balancing device for dynamic balancing, type ELASO MANOBALANCE 750/EB 2000 - RENAUD internal grinding spindle type REN 828 (grease-lubricated with compressed air lock) - Various internal grinding mandrels for REN 828 – 1235, 1645, 2060, 2575 (4 pieces) - Various chucks HJNZ 28 for HJN 828 with 2 collets D: 3 mm and D: 6 mm - Tailstock standard MK 5 with adapter flange DIN 55027 size 5” Bore D: 38.2 mm (standard) - Sine bar on the tailstock - Tailstock with manual retraction for quill travel - Micrometer adjustment on the tailstock - Pneumatic relief of the tailstock - FORKARDT planetary three-jaw chuck D: 200 mm - REISHAUER wedge-bar three-jaw chuck D: 160 mm - Permanent magnet chuck D: 200 mm - Collet chuck for Schaublin B32 - Set of 59 collets Schaublin B32, D: 1.0 – 30.0 mm, graduation 0.5 mm - Set of 8 workpiece supports incl. holder - Three-jaw steady rest, 175 mm, foldable, D: 3-120 mm - Swiveling dressing tool for dressing during external, surface or internal grinding - Side and angled dressing tool for side and angled dressing of the grinding wheels - Dial indicator stop for table swiveling with dial indicator 1/100 mm - Dial indicator stop for table longitudinal movement with dial indicator 1/100 mm - Dressing stop for internal grinding - HEIDENHAIN Digital length measuring system for the X and Z axes - STREULI paper band filter SPB 3, 90 l/min at 0.26 bar, tank volume 240 l - WALDMANN machine lamp - Set of vibration-damping pads - Three-color paint finish (light gray RAL 7035/blue RAL 5012/dark gray RAL 7016) - New acceptance test report according to KELLENBERGER standard - CE conformity - Documentation Condition: very good, machine geometrically and mechanically overhauled (see geometry report) Hnjdpjzhma Djfx Ahzep

Condition: good (used), Year of construction: 2003, Ref. -No.: 10618 Manufacturer: KELLENBERGER Type: 600 U Nr. 33 Year of construction: 2003 Type of control: Konventionell Control: n/a Hnjdpfx Aheya Dagozop Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175 - 250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0 - 5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 1500 / 1700 / 2200 / 3600 Swiveling grinding wheel head: 360 ° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Micro-corrector of the feed, 1 division of the dial: 0,001 mm / Ø Working speeds continuously adjustable (normal / special): 20-400 / 10-400 Max. Grinding length: 900 mm Further information: The machine can be viewed while powered up.

Condition: used, TECHNICAL DETAILS - Distance between centers : 600 [mm] - center height : 125 [mm] - Table orientation : 11 [°] GRINDING WHEEL HOLDER HEADSTOCK - Left grinding wheels dimensions : 400 x 50 x 127 [mm] - Power : 3 [kW] - Spindle speeds : 1500 / 1700 / 2200 [rpm] - Orientation of grinding wheel holder headstock : 270 [°] PART-HOLDER HEADSTOCK - Orientation of part holder headstock : 360 [°] - Spindle speeds : 20 - 400 [rpm] - Spindle internal cone : Morse 5 - Power : 0.9 [kW] TAILSTOCK - Internal cone : MT4 - Quill stroke : 30 [mm] POWER SUPPLY - Supply voltage : 380 [V] WEIGHT & DIMENSIONS - Machine floor space : 2580 x 1680 [mm] - Machine height : 1670 [mm] - Machine weight : 2200 [kg] EQUIPMENT - Coolant tank * with paper filtering unit - 1 internal grinding spindle - Lubricating tank with pump Hnjdjzf Rcdspfx Ahzsp - 1 three-key steady rest - 1 inner spindle alignment device

Condition: good (used), Year of construction: 1997, Ref. -No.: 10619 Manufacturer: KELLENBERGER Type: 600 U Nr. 35 Year of construction: 1997 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175 - 250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0- 5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 1500 / 1700 / 2200 / 3600 Swiveling grinding wheel head: 360° ° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Hedpfxezc D Dqe Ahzenp Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Working speeds continuously adjustable (normal / special): 20-400 / 10-400 Max. Grinding length: 900 mm Further information: The machine can be viewed while powered up.

Condition: good (used), Year of construction: 2001, Ref. -No.: 10617 Manufacturer: KELLENBERGER Type: 600 U Nr. 36 Year of construction: 2001 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Hnodpfx Ahjzc D Dkszep Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175-250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0 -5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 360° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Micro-corrector of the feed, 1 division of the dial: 0,001 mm / Ø Working speeds continuously adjustable (normal / special): 20 - 400 / 10-400 Max. Grinding length: 900 mm Further information: The machine can be viewed while powered up.

Condition: used, 3 flanges for type 600 U – available for sale individually or as a set Hjdpfx Ahoza Hnyezsnp

Condition: used, internal diameter 340/440 mm grinding depth 99999 mm grinding diameter 250,350,450 mm grinding length 600 mm centre height 125,175,225 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±10 ° longitudinal feed of the table 900 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,2 t dimensions of the machine ca. 3,1 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your metrical overhauled and repainted with: -Neuem CE konformem Schaltschrank. -Neuem Werkstückspindelmotor und Regler in Drehstromtechnik. -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my Optionen: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: -Bedienwerkzeug -Spannrohr für Futter weiteres Zubehör auf Anfrage. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Hodpod Ih Dxsfx Ahzsnp Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 250,350,450 mm grinding length 600 mm Hnodsd Ih D Nepfx Ahzjp centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±10 ° longitudinal feed of the table 900 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,2 t dimensions of the machine ca. 3,1 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your rhauled with geometric KELLENBERGER protocoll -2-axis DRO -Paper filtration Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 250,350,450 mm grinding length 600 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±10 ° longitudinal feed of the table 900 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,2 t dimensions of the machine ca. 3,1 x 2,0 m Compete overhauled machine according to Kellenberger new machine protocoll -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my Optionen: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: Hnsdpfod Ih D Rjx Ahzop -Bedienwerkzeug -Spannrohr für Futter -Spitze MK3 -Spitze MK5 -Futterflansch weiteres Zubehör auf Anfrage. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.