Briquetting Press

muetek MAP 1200

Condition: good (used), Used machine, good condition. Delivery time appr. 9 weeks after ordering Basic machine starts at 139.700 € net *Options at additional cost, see below Briquetting press e.g. for wood dust, spelled husks, activity material (e.g. for pigs to play and nibble around), animal feed, lucerne or wood shavings. *Optionally, short briquette tablets can be made Technical specifications: E27N38Yny Throughput capacity up to a maximum of 750 kg/h (depending on the material) (e.g. sawdust with a bulk density of 250 kg/qbm) An exact statement about the throughput is only possible after a test with your material. Can vary greatly depending on the bulk density of the starting material. Goods tariff number: 84793010 Briquette Ø 65 mm including 2 m press channel Engine power main engine 37 kw Feed screw geared motor 2.2 kw Compressor screw 5.5 kw Hydraulic pump motor 0.37 kw Total connection value: approx. 47 kW Control panel with plain text display for operating states and utilization indicator for the main drive and feed screws PLC control with operating hours counter in the control cabinet Machine has CE mark Automatic start-stop function Dimensions 3100x860x1800 mm lxwxh Weight 3800kg Options at extra cost: Temperature control unit for the pressing tools to maintain the temperature for optimal briquette quality. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - absolutely necessary for operation including the corresponding control + €7,850 net guillotine or pill crusher, for cutting the briquettes to length + €6,900 net Necessary for compressed air connection! Silo for MAP series + €19,940 net - Storage silo above the machine - Content approx. 6 sqm, stable steel construction with agitator discharge and level indicator. Transport line / cooling section (nominal value: 4x2m) each 2 meters 990 euros net Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site) according to expenditure on proof against separate calculation. The following sentences apply: Service technician/mechatronics technician per hour of assembly and travel: €129.00 Overtime: 25% surcharge 50% surcharge for each Saturday and night hour 100% surcharge for each Sunday and holiday hour Release per mechanic per day: depends on the country Per car and van and driven kilometer: 0.98 € / km Arrival and accommodation against receipt or flat rate billing at the expense of the client. . Test with the respective customer material: (by arrangement, up to a maximum of 750 kg) - 1,970 € net . Raw material requirements: - The moisture content (atro) must be between at least 6 and a maximum of 15% - Maximum chip length 18 mm - Installation temperature: room with a temperature of at least +5°C - The charge must be free of metals and mineral impurities. This can result in damage to the pressing tools and/or increased wear

Condition: good (used), Batch mixer mixer MAP Batch mixer 3Ztlets9E8 Engine power 22kW Speed 111rpm Execution: Steel Low wear Mixing bowl dimensions D:1000mm L:1500mm Overall length 3200mm See our other advertisements

Condition: as good as new (ex-display), Year of construction: 2024, Special price: €29,970 net A machine is currently available immediately. The ideal machine for shredding voluminous, light aluminum chips or turnings. Not suitable for more solid aluminum parts. Includes: + Optimized cutting geometry + Adapted slide control + Load-dependent controlled hydraulic slide (which presses the chips against the cutting mechanism) Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Blade: 40x40mm, multi-rotatable, Cgfperr8 Rotor diameter: 260 mm, Control: Omron PLC, Cutter opening 600 x 800 mm, Funnel volume approx. 0.6 qbm, Hydraulically operated slider Sieve perforation of your choice (15 - 40mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm The following options are available for an additional charge: - Raise the shredder by 30 cm (preparation for conveyor belt) +2,990 € net - Angle conveyor belt (discharge height approx. 220 cm) +9,770 € net - Overband magnet + €6,980 net - Control of conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the chipper) We would be happy to carry out a free test with your material. We invite you to come to us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos.

Condition: ready for operation (used), Year of construction: 2020, Functionality: fully functional, machine/vehicle number: 17WB170000116, power: 18.5 kW (25.15 HP), rotational speed (max.): 1,500 rpm, -Theoretical usable volume: max. 385 liters -Horizontal cylindrical mixing drum -End walls bolted to drum -Mixing tools as inclined blades bolted to blade arms in pockets -Shaft mounted in flange bearing housings with roller bearings arranged outside the mixer -Shaft sealed by easily replaceable stuffing box packings -Stuffing box packings with additional air purge connection for customer-side compressed air connection -Feeding via 1 nozzle D= 223mm with flange, XKF 352 -Venting via 1 nozzle D= 323mm with flange, XKF 352 with filter bag including holder and welded-in protective grille -Emptying via dead space-free closing flap, pneumatically operated, 1 outlet nozzle D= 406mm with flange, XKF 382 -Liquid addition option via 2 removable lances with Spray nozzle, mounted at knife head level -Inspection and cleaning through 1 flap on the front of the drum, dimensions: 1050 x 400mm, flap closed via quick release -Work and accident protection through locking magnet made by TELEMECANIQUE and limit switch (unwired) -Materials: Mixing drum, mixer shaft and mixing tool made of: stainless steel 1.4306 -Drive: The drive is not designed for frequency converter operation Complete with hollow shaft gear, three-phase motor and torque support -Technical data of the motor: Nominal power P = 18.5kW Nominal speed N = 1500 rpm Vl07Zkvcw Voltage U = 400/690 V - 50Hz Design B 5 Protection class IP 55 -Please note that the drive power is not designed for starting the mixer in star/delta when the machine is full! -Accessories: 2 knife head mounting flanges for the subsequent installation of knife heads Bag chute DN300 in stainless steel 1.4301, including flat seal and fastening material -This mixer is NOT ATEX-certified -Surface treatment: Mixing drum inside: ground grain 120 Mixing drum outside: glass bead blasted Drive and end bearing units 1 top coat according to RAL 5010 -Documentation: Maintenance and operating instructions in German as a .pdf file Installation drawing as a .dwg file or .pdf file Installation declaration

Condition: refurbished (used), Year of construction: 2011, operating hours: 655 h, Functionality: fully functional, fuel type: diesel, fuel: diesel, gearing type: hydrostat, Hako Jonas / Sweepmaster 1200 D Refurbished sweeper with 6 months warranty and new DGUV V3 test including test report. Working width with two side brushes: 116 cm Central sweeping roller: 80 cm Dqvwc7 Area performance max.: 10400 m²/h Container capacity: 130 l Drive type: diesel engine - LOMBARDINI New parts installed / repairs carried out: - Refurbished diesel engine - All drive belts new - All ball bearings on the deflection rollers new - Heavy-duty wheel at the front new - All rubber strips new - Box filter/hydraulic filter/oil filter/air filter new - All oils new - Sweeping unit completely overhauled We also offer: Service, repairs and sales for all common Hako models.

Condition: excellent (used), Functionality: fully functional, ZÜND S3 L 1200 C93Ilrm

Condition: used, Year of construction: 2021, Used machine Year of construction 2021 525 operating hours Deduster Suction nozzle diameter 350 mm Motor 11 kW, 400 V, 50 Hz Volume flow max. 8000 m³/h Nominal volumetric flow at 20 m/sec: 6950 m³/h Negative pressure at total connection at 20 m/sec: 2630 Pa Filter: 23 cartridge filters Filter surface 71 m³ H3 "GS dust-tested residual dust content < 0.1 mg/m³ Pneumatic JET filter cleaning (compressed air supply on site) Compressed air connection 3/4 inch, connection pressure 7-12 bar with 50 NL/min Operating pressure in the device 6 bar Extinguishing device with powder extinguisher, dry fire extinguisher 12 kg Frequency converter Weight approx. 865 kg with briquetting press MPP 60 Briquette diameter 50 mm Throughput capacity (depending on material) max. 60 kg/h (based on a bulk density of 200 kg/m³ Motor power 5.5 kW Oil volume 110 l Silo diameter 1000 mm Silo content; approx. 0.7 m³ Pump 27 l Hydraulic pre-compressor with cooling oil hydraulics with fill level monitoring incl. special tank for RL 350 Base area approx. 2200 x 1100 x 3100 mm availability: short term Bpzmg00J Storage location: Flörsheim

Condition: excellent (used), CATALOGUE NUMBER 6901 TECHNICAL DATA - max. turning length 1200mm - max. turning diameter 210mm - max. turning diameter with standard steady rest 90mm - max. size of square material for turning with automatic feeding 100mm - 3 hydraulic copiers - additional 3 knives on hydraulic pistons (2 pieces installed) - 4 types of spindle speeds - automatic or manual machine operation - 9kW headstock spindle motor - 3kW hydraulic pump motor - diameter of the exhaust port 90mm - dimensions for transport length/width/height 3700x2100x2000mm - weight approx. 3000kg ADVANTAGES - Italian production - automatic hydraulic copier - original DTR documentation - unpainted - used lathe, condition very good Net price: PLN 69,900 Net price: EUR 15,880 Net price calculated according to the exchange rate of PLN 4.4/EUR Cqkhhjvzx3 (in case of larger exchange rate fluctuations the price may change)

Condition: as good as new (ex-display), Year of construction: 2024, operating hours: 8 h, Machine in pre production *planned to be ready appr. end of march 2025 Very robust machine with high pressing force - is also suitable for producing a salable briquette quality * depending on the material. The large press cylinder and the 80 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for cooling unit + € 4.995 net, (can also be retrofitted later) * cools the pressing tongs (important from 3.5 hours) and the hydraulic oil * Cooling device recommended for regular use of more than 3.5 hours at a time. Briquette diameter: 80 mm Front bush: 125 mm Briquette stroke max .: 100 mm Briquette lift opt ​​.: 80 mm Output (depending on material): up to 200 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Motor power: 9.2 kW 400 volts / 50 Hz / 3 phases Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Silo diameter: 1200 mm Silo content: approx. 1 qbm Pump: 75 liters Hydraulic pre-compressor Cooling pressing tongs option: yes, with special accessory coolable pressing tongs Sigba0Id Hydraulic oil cooling option: yes Cooling of the pressing tongs and the hydraulic oil with cooling device (special accessory) Level monitoring option: yes Strand briquette option; yes (depending on material) Option of enlarged filling slide: yes, with special accessory enlarged filling slide CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: used, Year of construction: 2010, x-travel 500 mm y-travel 700 mm z-travel 500 mm A-axis 240 (-120/+120) ° C-Axis 360 ° control Siemens 840 D work table: faceplate diameter 440 mm T-slot - width 14 mm T-slot - distance 75 mm max. table load 400 kg main spindle: max. turning speeds 20.000 min/-1 tool taper HSK 63 A Dqpiet tool magazin: workpiece length 330 mm tool diameter 125 mm change-time chip to chip 4,5 sec weight of the machine ca. 10,5 t dimensions of the machine ca. 2,5 x 5,2 x 3,5 m

Condition: good (used), The scope of delivery includes: 01x back wall grille, used material color: similar beige total width: approx. 1.200 mm total height: approx. 1.100 mm Mesh size (outside): approx. 93 x 53 mm Mesh width (inside): approx. 88 x 48 mm Frame profile dim.: L-profile 30 x 30 mm E9Esyen The back wall grids are rusty, partly the frame profile is damaged, see pictures.

Year of construction: 2025, Condition: new, Model ML-1200 Infrared protection Ctebtcowuc Automatic oil system Max. sheet size 1200X820(mm) Machine speed(Strokes/Min) 20±2 Max.Rule Length(m)

Condition: new, Year of construction: 2024, Demonstrator; immediately available ex works Neckartailfingen Very robust machine with high pressing force - is also suitable for producing a saleable briquette quality *depending on the material. The large press cylinder and the 70 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to faults + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for demonstration cooling unit + 4,980 € net, (can also be retrofitted at a later date) * Cools the press tongs (important from 4 hours) and the hydraulic oil * Cooling unit recommended for regular operation of more than 4 hours at a time. Product code: 84793010, Briquette diameter: 70 mm, Front bush: 125 mm, Briquette stroke max.: 100 mm, Briquette stroke opt.: 80 mm, Capacity (depending on material): up to 150 kg/h* Beyiwm8Wjh *depending on bulk weight, *based on a bulk weight of 200 kg per cubic meter. . Motor power: 9.2 kW, 400 Volt / 50 Hz / 3-phase, Length: 2095 mm, width: 1300 mm, * with large chamber 1600 mm Height: 1700 mm, Weight: 1250 kg, Oil volume: 220 liters, Silo diameter: 1200 mm Silo capacity: approx. 1 qbm Pump: 75 liters Hydraulic pre-compressor Cooling press tongs option: yes, with optional cooling press tongs Hydraulic oil cooling option: yes Cooling of the press tongs and hydraulic oil with cooling unit (special accessory) Fill level monitoring option: yes Briquette option; yes (depending on material) Enlarged filling slide option: yes, with special accessory Enlarged filling slide CE compliant Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18 % - Maximum chip length 20 mm - Installation temperature: tempered room at a minimum of +5°C - The feed must be free of metals and mineral impurities such as sand, stones, etc. Damage to the pressing tools and / or increased wear may result

Condition: new, Year of construction: 2023, The ideal machine for shredding hardwood and softwood Another machine, available immediately (ex works Neckartailfingen) . Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Knives: 14+2 pieces, 40x40mm, multiple rotatable, Rotor diameter: 260 mm, Control: Omron SPS, Cutting unit opening 600 x 800 mm, hopper volume approx. 0.6 qbm, hydraulically operated pusher Screen perforation of your choice (12 - 40 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm . The following options are available at extra cost: - Additional row of knives + 995 € net (28 instead of 14) - Surcharge for 4-sided segment shelf + € 2,170 net (prevents blocking of the pusher. Recommended for materials with a thickness of less than 3 mm) Bea9Ia3L27 - Raise shredder by 30 cm (preparation for conveyor belt) + € 1,980 net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overbelt magnet + € 5,980 net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) - Special bearing +1,540 € (rarely required. Closed, even more stable rotor bearing. Possibly a consideration for sieves smaller than 15 mm or with a lot of fines. Not necessary if the bearings are lubricated with grease every approx. 2 weeks during operation) . Requirements for the raw material: - The moisture content (atro) must be below 30 % - Metals and mineral impurities such as sand, stones etc. lead to increased wear. . We will be happy to carry out a free test with your material and invite you to visit us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos.

Condition: as good as new (ex-display), Year of construction: 2023, Special price for our prefeeder Another machine, available immediately (ex works Neckartailfingen) approx. 24 operating hours. Suitable for shredding all types of waste wood and pallet offcuts. The pallet should be prepared with the jigsaw or chainsaw so that it fits upright in the hopper - see picture 2. 40x20x20 cm would be ideal so that the wood can lie flat on the pusher floor. This is where the machine works most effectively. At the bottom of the shredder there is a hydraulic pusher which presses the wood against the rotor depending on the load. The material is shredded until it passes through the screen basket. Throughput of up to 200 kg per hour *depending on the screen and how well the material is prepared. *Conveyor belt and overbelt magnet at extra charge. + Powerful 18.5 kW motor, + concave knives, + large high-performance gearbox, + special, load-dependent pusher control, Product code: 84659600 Motor: 18.5 kW; 400 V - 50 Hz - 3 ph. Knives: 15 pieces, multi-rotatable Option double row of blades + 995 € net Rotor diameter: 260 mm Control: SPS Siemens S7-1200 Cutting unit opening 630 x 820 mm Filling volume approx. 0.6 qbm Hydraulically operated pusher Screen perforation of your choice (10 - 30 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg (depending on accessories) Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm Moisture content: ᐸ 30 % Atro . Included as standard: - V-rotor for maximum throughput - Switch cabinet with Siemens PLC control - Automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idling - speed 70-90 rpm for high throughput capacity - Cycle control to avoid idling times - Performance-enhancing step control of the hydraulic slider - Pertinax guides for hydraulic slide - Vibration-damping machine feet - CE Conform. - MADE IN GERMANY . Shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €2,080 net - Folding conveyor belt +8,770 € net Horizontal part: 1200 mm Rising part: 2500 mm Angle: 0-60 degrees adjustable Discharge height: approx. 2000 mm + - 100 mm - Overbelt magnet + € 5,980 net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) - Hopper adjustment + 940 € net - Eco rings: + € 1,980 net (recommended for more than 15 % hardwood) - Special scraper + 990 € net (recommended for veneer or paper) - Double row of knives + 995 € net . Requirements for the raw material: Jux3Pi - The moisture content (atro) must be below 30% - Metals and mineral impurities such as sand, stones etc. lead to increased wear.

Condition: new, Year of construction: 2024, operating hours: 6 h, ready produced Our best-selling briquetting press, the classic. + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Options for an extra charge: * Surcharge for the level indicator that enables automatic operation + € 995 net * Surcharge for large pre-compression chamber + 980 € Bst09Lehrk (recommended for light material like straw) Briquette diameter: 50 mm Front bush: 50 mm Briquette stroke max .: 40 mm Briquette lift opt ​​.: 40 mm Throughput (depending on material): 30-60 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW 400 volts / 50 Hz / 3 phases Length: 1680 mm Width: 1100 mm Height: 1500 mm Weight: 680 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo content: approx. 0.7 square meters Pump: 27 liters Hydraulic pre-compressor Option cooling pressing tongs: no Hydraulic oil cooling option: yes Level monitoring option: yes CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Maximum chip length 15 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The customer must insure himself against loss of hydraulic oil - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: as good as new (ex-display), Year of construction: 2023, Special price for trade fair machine Special price: €39,995 net Combination of: mütek briquetting press MPP 60 + suction device MMJET 350 *Approved for indoor installation *Both individual machines fully produced and in stock, they only need to be connected to each other 1. Technical data for briquetting press: Our best-selling briquetting press, the classic. + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Trade tariff number: 84793010 Briquette diameter: 50 mm Front bushing: 50 mm Briquette stroke max.: 40 mm Briquette stroke opt.: 40 mm Throughput (depending on material): up to 60 kg/h* *depending on bulk density *based on a bulk density of 200 kg per cubic meter . Motor power: 5.5 kW, 400 volts / 50 Hz / 3-phases, Floor area of entire system: 2.2x1.1x 2.8 m LxWxH Height - 2.8 m (special container) Delivery also possible in 2 components Weight: approx. 1200 kg, Oil quantity: 110 liters Silo diameter: 1000 mm Pump: 27 liters Hydraulic pre-compressor Option cooling press tongs: no Option cooling hydraulic oil: yes Option level monitoring: yes CE compliant 2. Technical data for clean air extraction device MMJET 350: B3T3Gvt Extraction connection diameter: 350 mm Motor: 11 kW Extraction nozzle on the left (when standing in front of the dust bin) Residual dust content: ᐸ0.1 mg/m³ Max. volume flow: 8000 m³/h Nominal volume flow (20 m/s): 6950 m³/h Filter area: 71 m² Underpressure: 2630 Pa Automatic filter cleaning Cartridge filter JET cleaning Powder fire extinguisher installed (checked every 2 years by a specialist company) Requirements for the raw material: - The moisture content (atro) must be between at least 6 and a maximum of 18% - Compressed air provided by the customer - Maximum chip length 15 mm - Installation temperature: temperate room at at least +5°C - The customer must choose a press that is large enough so that it removes more material than is sucked in at peak times - The feed must be free of metals and mineral contaminants such as sand, stones, etc. Damage to the pressing tools and/or increased wear can result.

Condition: new, Year of construction: 2024, Consisting of bale loosener for large bales type MHB and straw shredder type MHZ 1) Bale breaker MHB: Special price from 24.975 € net Production time approx. 15 weeks Suitable for round or square bales. Including FU (frequency converter) - this regulates the speed of the scraper floor The bales are placed on the scraper floor and the tiller feed is switched on. The tines of the scraper tear the straw off the bale and throw it into the hopper. Ideally, the combination of bale breaker and straw shredder is ideal here Bale breaker technical data: Output: 1-2 bales per hour up to a maximum of 600 kg per hour (depending on the sieve size used in the straw mill, kW number of straw mill. Without a straw mill, the bale breaker can even break up to a maximum of 900 kg / h. straw) max size square bale 2400x1200x800 mm lxwxh Tiller motor 5.5 KW 380 Volt Scraper floor feed 0.75 KW 380 Volt Dimensions 3750x1730x2460 mm lxwxh Weight 400 KG 2) Straw mill MHZ 600 - 11/15 kW; available immediately Special price from 7.995 € net Special hopper: + 495 € (only in combination with bale shredder) Surcharge for the even larger straw mill (18.5 kW) + € 1,440 net Technical data mill MHZ with special hopper: Motor 15 KW 380 Volt electric motor Diameter: 600 mm Hardened cutting blades sieve with interchangeable inserts optional 10, 12,15,22,30,45 mm perforation with star delta switch Ue protection and 8 m supply cable ready to plug in Discharge nozzle 160 mm Blowing range approx. 12 m Dimensions approx. 1600 x 1020 x 1360 mm lxwxh Weight approx. 240 KG --- Options: Special dissolver extension 3 m *other dimensions would have to be calculated + 6.995 € net Cyclone (suspension by customer) *Should be a maximum of 10 m away + 970 € net Surcharge for an extraction system (demonstrator) (can also sit on the press; for transporting the chips) + from 9,990 € net Briquetting press MPP 180 S; little used demonstrator 70 mm briquette Rxqwlvgbg up to a maximum of 100 kg / h from 39.700 € net Briquetting press MPP 280 S; little used demonstrator 80 mm briquette up to a maximum of 120 kg / h from 44.990 € net * larger machines on request --- Description: muetek bale loosener was developed for loosening round and square bales of hay and straw. The shredder flanged to the bale loosener shreds straw from all types of grain, hay, maize and miscanthus. The muetek machines in the MHZ / MHB series are characterized by their robust design and solid construction. This guarantees consistent quality in continuous operation. muetek bale loaders of the MHB series are equipped with a chain conveyor onto which the straw bale is placed with the front loader. The support can be adjusted depending on the type of bale. The chain conveyor presses the bale against the milling rotor and the feed speed is adjustable. The milling rotor is equipped with several teeth that tear open the straw bale. The straw separated from the bale is ejected. Sieves 10-60 mm --- Basically, the machines work for dry raw materials: - Straw - hay --- The pulping of hemp only works with a special pulper Surcharge approx. 9,700 € net * depending on version. The shredding of hemp does not work with the straw mill. *If at all on a cutting mill

Condition: new, Year of construction: 2024, Delivery time approx. 4 months . The hydraulic briquetting presses of the MPP NEM series press materials such as aluminum, copper, brass, bronze, graphite and other non-ferrous metals into dimensionally stable cylindrical briquettes. The machines are characterized by a robust design that guarantees consistent briquette quality in continuous operation. The pressing process is carried out without the addition of binding agents using hydraulic pressing pressure alone. Depending on the material, the volume of the starting material can be reduced by up to 90%. Throughput rate: up to a maximum of 80 kg/h (depending on material), Briquette diameter: Ø 50 mm, Motor: 5.5 KW, 400 Volt / 50 Hz / 3-phase, Pump: 40 liters, . Briquette length max.: 50 mm, Briquette length opt.: 40 mm, Bixvstdg Diameter silo: 1,000 mm, Oil tank 110 liters . Dimensions: 1750x1130x1100 mm lxwxh Weight: 780 kg. . Hydraulic pre-compression via slide valve Main press cylinder Vertical cylinder . Level indicator: yes . Requirements for the starting material - Max. chip length: 15 mm - Installation temperature: tempered room at a minimum of +5°C - Max. Weight on agitator: 200 kg. - The feed must be free of magnetic metals and mineral impurities such as sand, stones, etc. Damage to the pressing tools and / or increased wear may result

Condition: new, Year of construction: 2023, Ideal for shredding straw, polystyrene, leaves, hay and bread. Throughput highly dependent on screen and source material: - up to a maximum of 350 kg / h for straw with a 15 mm screen - up to 60 kg / h for EPS with a 15 mm screen Motor 11 KW - 400 Volt, (9.2 kW or 15 kW also possible on request) Optional: *Surcharge for the next larger machine with 18.5 kW and larger silo diameter + € 1,995 net Sturdy steel construction, hardened cutting blades, sieve with replaceable inserts, optional (10),15,22,26,30,40,or 60 mm perforation with electric drive with star delta switch Ue protection and 8 m supply cable ready to plug in, Outlet connection 150 mm, optionally for plastic or core pipes, Ucbu22Bv Blowing range approx. 12 m, Chassis with 2 running wheels Ø 380 mm, and one swivel support wheel Ø 125 mm, all wheels with solid rubber tires, Dimensions approx. 1000 x 850 x 1270/1400 mm lxwxh Weight approx. 240 KG, Spare parts prices and options: 24 knives, hardened € 9.90 net each 6 bolts € 14.90 net each 1 sieve per 475 € net Lid € 290 net each Styrofoam disk: € 600 net each

Condition: as good as new (ex-display), Year of construction: 2023, Demonstration machine with approx. 20 operating hours Another machine, available immediately (ex works Neckartailfingen) *Options at extra charge - see below Included: + Profile rotor for higher throughput We will be happy to carry out a free test with your material. I would like to invite you to our premises in Neckartailfingen. It is also possible for you to send us your material by forwarding agent and we can document the test with pictures and videos. Motor: 18.5 kW; 400 V - 50 Hz - 3 ph Knives: 15 pieces, multi-rotatable, Option double row of knives + 995 € net Rotor diameter: 260 mm Ry2Ojkfiu Control: SPS Siemens S7-1200 Cutting unit opening 630 x 820 mm hopper volume approx. 0.6 qbm hydraulically operated slide Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm Moisture content: < 30 % Atro. . Included as standard: - V-rotor for maximum throughput - Switch cabinet with Siemens SPS control - automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idling - speed 70-90 rpm for high throughput capacity - Cycle control to avoid idling times - Performance-enhancing step control of the hydraulic slide valve - Pertinax guides for hydraulic slides - Vibration-damping machine feet - CE Conform. . Shredder options at extra charge: - Raise shredder by 30 cm (preparation for conveyor belt) + € 2,080 net - Eco rings: + € 1,980 net (recommended for more than 20 % hardwood) - Double row of knives + 995 € net - Special scraper + 990 € net (recommended when shredding veneer or paper, or items with a material thickness of less than 3 mm) - Articulated conveyor belt + € 8,770 net Angle: 0-60 degrees adjustable Discharge height: approx. 2000 mm - Automatic overbelt magnet + € 5,980 net Alternatively, fixed magnetic block above the conveyor belt for regular manual stripping + € 990 net (for low metal part accumulation) - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) alternatively manual start and stop of the belts + 595 € net . Requirements for the raw material: - The moisture content (atro) must be below 30% - Installation temperature: tempered room at a minimum of +5°C - Metals and mineral impurities such as sand, stones etc. lead to increased wear

Condition: new, Year of construction: 2023, Demonstrator with 15 operating hours Another machine, available immediately (ex works Neckartailfingen) Shredder MRZ 830 Product code: 84659600 Feed opening 800x1000 mm Motor: 18.5/ 22 kW; 400 V - 50 Hz - 3 ph Knives: multiple rotating Hydraulically operated pusher Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 200 mm Weight approx. 1,600 KG Dimensions (lxwxh) approx. 2290 x 1420 x 1750 mm Turbo coupling Included as standard: - Automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idling Bdqriiu289 - Speed 70-90 rpm for high throughput capacity - Cycle control to avoid idling times - Performance-enhancing step control of the hydraulic slider - Pertinax guides for hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding untreated wood, chipboard and MDF and other materials after testing and approval by the manufacturer. . Other shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + € 2,140 net - Folding conveyor belt + 8.770 € net Horizontal part: 1200 mm Rising part: 2500 mm Angle: 0-60 degrees adjustable Discharge height: approx. 2000 mm + - 100 mm - Overbelt magnet + 5.980 € net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) . Requirements for the raw material: - The moisture content (atro) must be below 30 %, - Installation temperature: tempered room at a minimum of +5°C - Metals and mineral impurities such as sand, stones, etc. lead to increased wear

Condition: as good as new (ex-display), Year of construction: 2023, Special price for our prefeeder Another machine, available immediately (ex works Neckartailfingen) approx. 24 operating hours. Including: + profile rotor for increased throughput Igkchryd0 Options: Double row of knives + 895 € net Veneer and paper scraper + 970 € net * Recommended for extremely thin materials with a thickness of less than 3 mm Our mütek MRZ 530 single-shaft shredder shreds a wide variety of materials such as all types of waste wood, softwood, chipboard and hardboard, pallets, construction timber, demolition wood, carpet, cable, paper, cardboard and plastics. The machine is characterized by its robust design, which guarantees consistent quality in continuous operation. We will be happy to carry out a free test with your material. We invite you to visit us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we can document the test with pictures and videos. Machine data: Motor: 15 kW; 400 V - 50 Hz - 3 ph, Blades: multi-rotatable, Rotor diameter: 260 mm, Control: PLC Siemens S7-1200, Hopper (mm) 510 x 810 mm, Hopper volume approx. 0.4 qbm, throughput 1 - 5 hopper fillings / h, hydraulically operated pusher, Screen perforation of your choice (10 - 40 mm), suction nozzle Ø 160 mm, Weight approx. 1,000 kg, Dimensions approx. 1550 x 1100 x 1640 mm, Moisture content of the raw material: must be below 30 % atro. Included as standard: - Fast hydraulics - Profile rotor - Switch cabinet with Siemens PLC control - Automatic star/delta start - Automatic OFF when the rotor is idling - Removable suction chute - Speed 70 - 100 rpm for higher throughput capacity - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Stable guides for the hydraulic slide Other shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) +1,980 € net - Folding conveyor belt +8,770 € net Horizontal part: 1200 mm Rising part: 2500 mm Angle: 0-60 degrees adjustable Discharge height: approx. 2000 mm + - 100 mm - Overbelt magnet + 5.980 € net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) . Requirements for the output or raw material: - The moisture content (atro) must be below 30% - Metals and mineral impurities such as sand, stones, etc. lead to increased wear

Condition: new, Year of construction: 2024, Diameter: 160mm Also available in the diameters: 180, 200, 250, 300 mm for an additional charge, other diameters on request. Very stable industrial design. Ideal for separating nails/metal parts from material flows. For example after a wood shredder. including 3 extremely powerful magnets Vi2Zo * If desired, up to 6 magnets can be installed in the component - surcharge for each additional magnet + 49 € - Neodymium magnets are also available instead of ferrite for an additional charge Your advantages: + Extremely large inspection door with seal for easy stripping of the nails + Stable quick-release fastener +Made in Germany Inspection door / opening: 35x18 cm Installation length may vary

Condition: as good as new (ex-display), Year of construction: 2023, at a special price of €14,995 net Consists of press and extraction 1) Briquetting press: Your advantages: + very robust, simple technology + top price-performance ratio + suitable for continuous operation + long-standing, well-functioning / established machine Including control cabinet with timer operation The press is switched on manually and then runs until the set time on the timer (e.g. 4 hours) has elapsed. Then the press switches off. Technical data: Briquette dimensions: approx. 35 x 35 mm (square), Briquette length: 5-40 mm *depending on material Throughput up to 20 kg / h *depending on material Dimensions of the machine approx.: 137 x 75 x 210 cm (length x width x height), Weight of the machine: approx. 350 kg, Silo capacity: approx. 250 liters, Motor: 2.2 kW, 400 V - 50 Hz, Noise emission: 62 dB, Raw material requirements: -Wood chips and dust less than 15 mm in length -Moisture content less than 18% ATRO -Sand, stones, metals and minerals increase wear --- Options at extra cost: * Level sensor for automatic operation + € 995 net Bzc8Fnk8Sp Press starts and then stops automatically ----- 2) Extraction: Motor: 2.2 kW Volume: 1400 m³/h Noise level: 87 dB (A) Weight: 160 kg. with 2 extraction connections - 100 mm each Filter unit: The filter chamber contains class L or M filters, which, thanks to a large surface and high filtration efficiency (3 micrometers), ensure a high dust retention capacity and air purity at the outlet. *Accessories and hoses on request *Larger or smaller extraction devices on request (0.75/1.5/2.2/3.0 kW) *Atex version optionally available Surcharge + €980 net