Ring bending machine & profile bending machine

OSTAS OPK-32

Condition: as good as new (ex-display), Year of construction: 2007, I - beam section - flat steel 50 x 10 mm I-beam section - upend 80 x 15 mm L-beam 50 mm Nljdpfx Agot U R H Ujrjg round material 30,0 mm bar material dia. max. 1 1/2" mm bar material - diameter 30,0 mm weight 185 kg range L-W-H 670 x 530 x 1350 mm square material 40 x 40 x 3 mm pipes 60 x 2,0 mm Thickness of tenon 30 mm total power requirement 0,75 kW Demonstration device Equipment: • Base frame of the machine • Foot switch • Standard-rolls (divided) • Possible to bend horizontally and vertically • machine has only one drive (right-left-run)

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, sheet thickness (max.): 60 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), Equipment: cone bending device, documentation/manual, 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls 570 / 500 / 430 mm Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Nledpfozbqquex Agrsg Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), functionality: fully functional, Year of construction: 2000, machine/vehicle number: 3roll 3500x140 mm prepinch, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: MG, controller model: MG, number of rollers: 3, roller (bottom) diameter: 880 mm, roller (top) diameter: 950 mm, side roll diameter: 880 mm, roller length: 3,550 mm, working width: 3,500 mm, working height: 3,950 mm, sheet thickness (max.): 140 mm, sheet thickness steel (max.): 175 mm, overall weight: 200,000 kg, total length: 8,800 mm, total width: 5,100 mm, total height: 5,775 mm, power: 200 kW (271.92 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, Hydraulic Plate Bending machine planetary pinch pyramid with prebend. model MG35140V 3 roll capacity 3500x140 mm The machine was overhauled in 2024, Capacity : Plate width mm. 3500 Plate thickness mm. 140 Capacity chart in enclosed Tech data: -3 rolls driven hydraulic motorized with axial gear unit on each roll independent -Synchronized hydraulic rotation of the 3 rolls with variable speed. -Planetary design with pre-pinch fully hydraulic -Conical plate bending with hardened contrast pad -Digital position readouts of the bending rolls -Rolls installed on bearings double crown heavy duty -Overload safety hydraulic operation protection of the 3 rolls -High pressure hydraulic power pack with multi-pumps oil feed -Centralized control panel electric on wheels with joysticks and digital readouts -Emergency stop with safety system around the machine working area Rolls surface length mm. 3550 Top roll mm. 950 Side rolls mm. 880 Electric power on hydraulic unit Hp 100 + Hp 100 Voltage 380 Vac / 50 Hz Configuration & accessories installed with the machine -Hardened surface of the 3 rolls -Conical plate bending attachment , rolls tilt with contrast roller type. Nsdeyzim Aopfx Agrslg -Centralized operator panel with directional joysticks electric. -Digital position readout of the bending rolls. -Emergency and safety installations, certified CE -User manuals and instruction books in English -Dimension see layout drw in enclosed

Condition: new, Ostas Profile Ring Bending Machine OPK 125 Technical Specifications: • Tool holder, shaft: 120 mm • Tool: 390 mm • Working speed: 2-7.5 m/min • Motor: 15 kW • Dimensions (L-W-H): 2000 x 1700 x 1950 mm Nedpfxoxrd Rns Agrjlg • Weight: 4850 kg • 3 rollers are driven separately by a hydraulic motor and planetary gearbox • Hardened standard rolls • Hardened and ground tool holder, shaft • Mobile control panel • Horizontal and vertical working position • Hydraulic side supports • Digital displays (2 pcs.) • In accordance with CE standard

Condition: new, Balkaya Profile Ring Bending Machine HBM 80 Technical Specifications: Tool holder, shaft: 80mm Tool: 245mm Working speed: 4.5m/min Motor: 4kw Hydraulics: 30 tons Dimensions L-W-H: 1450x1050x1800 mm Weight: 1400kg 3 driven rollers Njdpfoh T Ulnex Agrelg Hardened standard rollers Hardened and ground tool holder, shaft Mobile control panel Horizontal and vertical working position Digital display Complies with CE standards

Condition: new, Year of construction: 2024, shaft diameter: 80 mm, Profile bending machine AHB 100 - with universal rollers - Three roller drive - Digital display left and right bending axis - Hydraulic lateral rectifier - Hydraulic drive of the bending rollers - Vertical and horizontal operation - built according to CE standards Nsdpfovaw Elex Agrslg - Bending capacity flat bars max. 12 x 20 mm - Flat bent 200 x 40 mm - U profile inside and outside 180 mm - Angle profile web outside 100x100 mm - Angle profile web inside 90x90 mm - Solid material round 75 mm - INP 140 - Shaft diameter 100 mm - Roller diameter 315 mm - Bending speed 5 m/min. - Motor power 11 KW - Weight 2600 kg - module max Wcm3 -400 Volt 50 Hz. 3 ph. -1950x1600x2100 mm

Condition: used, Year of construction: 2012, functionality: fully functional, total length: 30,000 mm, drilling capacity: 40 mm, type of input current: three-phase, total width: 3,500 mm, drill diameter: 40 mm, input voltage: 400 V, FICEP HP35T - CNC SAWING & DRILLING LINE FOR ANGLE STEEL | YEAR 2012 | RECONDITIONED The Ficep HP35T is a CNC-controlled sawing and drilling line for the economical series processing of angle steel (L-profiles) in structural steelwork. Sawing and drilling run in a single automated pass with DSTV data connectivity, reducing handling, marking time and scrap for beam connections, gusset plates and lattice structures. CONDITION & RECONDITIONING Reconditioned and inspected by a certified technician, ready for operation. - The exact scope of reconditioning varies from machine to machine and is disclosed individually upon serious interest. - Viewing possible by arrangement (machine reconditioned - no demonstration under power). FUNCTION & APPLICATION The HP35T processes equal- and unequal-leg angle steel (L-profiles) up to 350 x 350 mm leg dimension and combines sawing with two drilling spindles (max. dia. 40 mm) into one continuous machining process. Material is fed via a motorized infeed roller conveyor, hydraulically clamped and positioned under CNC control. The PC-based Ficep CNC control enables manual programming at the operator terminal as well as direct program import from structural-steel CAD systems (e.g. Tekla, SDS/2, BOCAD) via DSTV. Typical applications: structural steelwork and profile processing, lattice and mast structures, plant and steel hall construction, gusset plates and beam connections. TECHNICAL DATA - Manufacturer: Ficep | Model: HP35T | Year: 2012 | Serial number: 25029 - Machine type: CNC angle processing line (sawing & drilling line) - Condition: used, reconditioned by certified technician - Cutting process: saw - Drilling spindles: 2 x drilling spindle, max. drill dia. 40 mm - Clamping: hydraulic - Profile type: equal- and unequal-leg angle steel (L-profiles) - Max. leg dimension: up to 350 x 350 mm | Min. profile: approx. from 50 x 50 x 5 mm - Feed rate (max.): approx. up to 40 m/min - Positioning accuracy, longitudinal axis: approx. +/- 0.2 mm - Hydraulic unit motor: approx. 15 kW | Feed motor (servo): approx. 3 kW - CNC control: Ficep proprietary / PC-based - DSTV interface: direct import from structural-steel CAD - to be confirmed during inspection - Electrical connection: 400 V / 50 Hz / 3-phase + N + PE (TN-S), control voltage approx. 24 V DC - Overall machine length: approx. 30,000 mm (line incl. roller conveyor; exact dimension before loading) - Machine width: approx. 3,500 mm | Machine weight: on request Note: Values marked "approx." are reference figures and will be confirmed bindingly during inspection. SCOPE OF DELIVERY - 1 x Ficep HP35T angle steel processing line (year 2012) - 1 x hydraulic unit (integrated) - 1 x CNC control unit with operator terminal - 1 x infeed roller conveyor (motorized) - 1 x electrical control cabinet - 1 x machine documentation / operating manual (Italian/English) LOGISTICS & LOCATION Location: Ulft (Netherlands), directly at the German border. Dismantling, transport, installation and commissioning can be carried out by ASM by arrangement - individually calculated upon request. ABOUT ASM Njdpexn T Smefx Agrjlg Arendsen Steel Machinery (ASM) specializes in reconditioned Ficep structural-steel machinery - from sawing and drilling lines and profile drilling machines to plasma cutting systems. Further Ficep machines on request. CONTACT / INQUIRY Arrange a viewing | Price on request | Request a callback. Sale exclusively to commercial customers (B2B).

Condition: new, number of rollers: 3, roller (bottom) diameter: 76 mm, roller (top) diameter: 76 mm, side roll diameter: 76 mm, Equipment: cone bending device, documentation/manual, emergency stop, foot remote control, swiveling upper roller, - Capacity: 1270 x 1.5 mm - Conical rollers - Removable top roller - Foot control - Emergency stop - Documentation Nljdpfx Aeh Ralqegreg - 400V

Year of construction: 2018, condition: ready for operation (used), Three almost identical CNC plastic pipe butt welding machines (mirror welding machines) Hürner are available. Years of construction: 2x 2016 and 1x 2018, working range OD: 40mm-160mm, power: 2.85kW, reduction inserts: 40/50/63/75/90/110/125/140, weight: approx. 80kg. Documentation available. On-site inspection is possible. Nledpfsviv Azsx Agreg

Condition: refurbished (used), functionality: fully functional, overall weight: 1,150 kg, total length: 1,680 mm, total width: 1,250 mm, total height: 1,390 mm, Year of construction: 2008, operating hours: 882 h, input frequency: 50 Hz, shaft diameter: 105 mm, type of input current: three-phase, Equipment: emergency stop, rotational speed infinitely variable, Profile bending machine PBT25 PC400 (will be refurbished, including a new Y-axis measuring device) For sale is a profile bending machine PBT25 with PC300 control, manufactured in 2008. The machine will be completely refurbished and technically inspected by PBT before sale. Technical data: Machine type: Profile bending machine Manufacturer / Model: PBT25 Njdjz Ak I Iopfx Agrolg Control: PC300 (upgrade in 2026) Year of manufacture: 2008 Operating hours: approx. 882 hours Condition: Good condition. Fully functional. Availability: Approximately two weeks. Further technical details and specifications according to the manufacturer can be found on pbt-ag.com.