CNC Portal flame cutting machine

Sato Satronik D5765

Year of construction: 2014, condition: ready for operation (used), A complete CNC double gantry plasma cutting system Microstep with oxyfuel torch for nesting, bevel cutting and tube processing is available. 1) Plasma cutting system, max. processing length: 16500mm, max. processing width: 2500mm, max. processing width including shaft: 3700mm, max. material thickness VA/structural steel: 20mm/40mm, number of gantries: 2. Gantry 1: with a plasma rotator and a Kjellberg HiFocus 280i neo plasma cutting source. Gantry 2: fully automatic oxy-acetylene torch for possible equipment of a second torch carriage. Pipe cutting device: pipe diameter range: 30mm-700mm, max. pipe length: 16500mm, operating hours: approx. 15000h. 2) Filter system Donaldson Cyclopeel DFPRO 16, volume flow: 16000m³/h, filter elements: 16. Documentation available. On-site inspection is possible. Expected to be available from the end of 2025/beginning of 2026. Pictures are from commissioning in 2014. Podpfxewmqwye Amxsrb

Condition: good (used), Year of construction: 2017, V304 plate processing machine (including 1 gantry beam(s) of 6.500mm and side trucks) ◼ This V304 plate processing machine is capable of processing plates up to 3.050mm x 18.000mm for bevel plasma cutting and marking (needle marker, if attached) and 4.100 x 18.000 mm for oxy-fuel cutting and marking (needle marker, if attached) ◼ X-rail (21.000mm on both sides of the machine, including double linear guides, helical rack and pinion system and rubber covering band) ◼ Plasma cutting and extraction table (4.300mm x 18.720mm, 2 channel(s), 1 pcs, suitable for ≥ 350A cutting) ◼ Position 1: Plasma cutting unit Kjellberg SmartFocus400 (1 pcs, automatic gas console, complete with cutting parameter database) ◼ Plasma 3D bevel unit (1 pcs, including 5 NC-axis, Voortman height control, intelligent torch positioning system and 3D collision sensor, for x- ,y- , k- and v-weld preparations) ◼ Driven suspension (1 pcs, servo motor driven, including laser pointer) ◼ Dross inhibitor (1 pcs, including 1,2L reservoir) ◼ Arc Glare protection (1 pcs) ◼ Position 2: Plasma cutting unit Kjellberg SmartFocus400 (1 pcs, automatic gas console, complete with cutting parameter database) ◼ Plasma 3D bevel unit (1 pcs, including 5 NC-axis, Voortman height control, intelligent torch positioning Psdpfx Amsvpalasxorb system and 3D collision sensor, for x- ,y- , k- and v-weld preparations) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Dross inhibitor (1 pcs, including 1,2L reservoir) ◼ Arc Glare protection (1 pcs) ◼ Position 3: Oxy-fuel cutting torch 4.0 (1 pcs, automatic gas console, ignition and piercing, complete with cutting parameter database) ◼ Voortman height control (1 pcs, capacitive height control) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Position 4: Oxy-fuel cutting torch 4.0 (1 pcs, automatic gas console, ignition and piercing, complete with cutting parameter database) ◼ Voortman height control (1 pcs, capacitive height control) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Position 5: Oxy-fuel cutting torch 4.0 (1 pcs, automatic gas console, ignition and piercing, complete with cutting parameter database) ◼ Voortman height control (1 pcs, capacitive height control) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Cables high instead of low ◼ Donaldson fume extraction unit DFO 4-48 - 200L (incl. frequency controller) ◼ Air conditioning for switch panel (up to an ambient air temperature of 55°C) ◼ Hardware and software (includes VACAM ‘Machine Edition’, VACAM ‘Office Edition’, VACAD editor software module, VANEST nesting software, Layout marking software module, online support) ◼ Post processor for SigmaNEST (SigmaNEST is provided by the customer) ◼ Safety devices (safety bumpers, emergency stop cord)