Wire straightening machine

unbekannt Abwickler-Richtmaschinen-Kombination

Year of construction: 1987, condition: ready for operation (used), An old Schumag Aachen drawing machine without control is available. Drawing force: 100kN, drawing speed: 80m/min, material diameter range: 25mm-43mm. On-site inspection is possible. Bodpfxov Tctue Alzolp

Condition: refurbished (used), functionality: fully functional, Löser centerless tube grinding machine - belt grinding machine - polishing machine - Cylindrical grinding machine Centerless tube grinding / polishing machine for workpieces with a minimum length of 1100mm. The machine was built in 1988 and was completely overhauled in 2012. The machine was converted for polishing and then only polished around 10,000 parts. The machine was no longer used after that. During the general overhaul, the motors, bearings and the entire control cabinet with the frequency converters were completely replaced. The machine can be used for both wet grinding and polishing. Bodpfjtmqi Dox Alzolp Wastewater treatment including pumps is not yet available. We can retrofit these for you according to customer requirements. The transport systems (roller conveyors) between the grinding stations must also be retrofitted to suit your workpieces. The machine can process pipe diameters from 10mm to 160mm. The grinding motors / polishing motors have an output of 7,5kW per station. The system can be viewed by appointment in our warehouse in D-63128 Dietzenbach.

Condition: new, Year of construction: 2026, width of the strips 50.0 mm band length 940 mm band speed 3.0 - 22 m/min turning speeds 1450 U/min tube diameter 10.0 - 114 mm radius 180 ° total power requirement 4.75 kW weight of the machine ca. 265 kg range L-W-H 1000 x 750 x 1300 mm Furnishing: - stationary pipe belt grinders - Automatic material feed with separate drive motor - Replacement sanding belts - Stepless speed adjustment - Manual adjustment of tube tension - Polish bent pipes up to 180" (angle). - Manual work possible without feed Bledoxaaxqjpfx Alzsp - CE mark / declaration of conformity

Condition: used, Year of construction: 1972, functionality: fully functional, machine/vehicle number: D08U/8378, Offer Number: D08U/8378 Bjdpfx Alew Nhv Dezslp Machinetype: straightening and cutting machine Info: flying shears Make: WAFIOS Type: RF6 Constr. year: 1972 diameter range: 8-16 mm cutting length: 520-6000 mm speed - meters/min: 25-75 diameter range: 8-14 mm Location: Outside of Europe

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 23087A, SPECIFICATION Maximum grinding surface 140 x 300mm Distance between column and wheel axis 300mm Max.distance between table and wheel 280mm Rapid feed per turn of handwheel 2mm Micrometric feed by small handle 0.01mm Size of cup wheel 2.2kW Wheel speed 2840rpm Approximate weight 400kg MACHINE EQUIPPED WITH 260mm x 140mm x75mm (thickness) magnetic chuck Coolant system Guarding Bledpfovntgusx Alzsp

Condition: used, Year of construction: 2000, Capacity: 250 ton V – Ring nominal force: 30 - 125 ton Counter ram nominal force: 30 - 125 ton Ram stroke: 64 - 67 mm Table surface area : 560 x 600 mm Slide area: 560 x 560 Bjdpfjzwfqajx Alzelp Number of strokes: 80 s.p.m. Weight of machine approx.: 14.000 kg Standard configuration Maximum material thickness: 10 mm Extended machine accessories including roller feedincluding waste-cutting shears Automation Straightening unit, model RLM 25-SMaterial width 50–250 mmMaterial thickness 6–10 mmNumber of straightening rollers: 5Diameter of straightening rollers: 88 mm Decoiler USM 2000 AS Coil weight: 2 tonnesCoil outer diameter: approx. 1,500 mmCoil inner diameter: approx. 508 mmMaterial width: 50–250 mm

Condition: used, Straightener & polishing machine WRPT2, manufactured by KIESERLING Bars diameter : 10 - 35 mm Bars length : 3 - 6 m Scope of delivery includes : 1. Infeed pinch-roll with - Motorised bottom roller - Vulkollan upper roller 2. WRPT2 straightening machines, made KIESERLING with - 2-roller straightener with upper roller height adjustment and upper/lower angle adjustment - Two geared motors with cardan shaft drive - Infeed guide - Side guide support - 1 set of side guides 3. Outfeed pinch-roll with - Motorised bottom roller - Vulkollan upper roller 4 Electric control panel with manual movement buttons Bars diameter: 10 - 35 mm Bljdpoymcm Eofx Alzep Bars length: 3 - 6 m

Year of construction: 2003, condition: good (used), functionality: fully functional, machine/vehicle number: 03234, 6 Brush ( 3 pairs) descaling machine for steel wire size 5.5mm - 16.0 mm max (low carbon) Brush pairs arranged in a 60 degree offset for maximum effect. A very clean looking machine. Bjdpfx Aex R Uzdslzslp On site viewing and inspection recommended

Condition: ready for operation (used), functionality: fully functional, DESCRIPTION OF MACHINE INCLUDED A LOT BELTS A Löser abrasive belt grinding machine offers the most flexible grinding / linishing on the market today. The combination of basic machine plus a variety of contact arms and attachments offers dozens of possible applications for many different purposes. There are over 20 standard attachments available for this machine allowing it to be used for centerless grinding, internal polishing, grinding of hollow bodies and small radius and turbine blade finishing to name but a few. Fields of application of these abrasive belt grinding machines include: *Foundries *Medical engineering *Aircraft industry *Vehicle construction *Mechanical engineering *Specifications Abrasive belt grinding machine, type KS 350 *Grinding belt length 3000-4000 mm *Grinding belt width 5 - 75 mm Loser KS 350 Belt design features:: Bedpfswxrnwex Alzslp *Drive motor 4 kW (standard design) with fitted variable speed inverter drive *Drive wheels of 100 - 280 mm diameters = 3 - 46 mtr./sec. belt speed *Mechanical belt tensioning *In case of a belt break the drive is immediately disconnected. Therefore, the risk of an accident is eliminated. *Contact disks of 50 - 400 mm diameters, with a wide choice of grinding attachments for any kind of surface finishing * DC injection breaking unit fitted. *Maintenance-free, dust-proof contact disk bearing with permanent lubrication, contact disk change in less than 1 minute. *LÖSER abrasive belt grinding machines open up new fields of application for belt linishers that in the past could not be processed with normal belt grinders. *When using 3 to 4 m long grinding belts, the 3-contact wheel system ensures the constant and optimal belt speed no matter which contact disk diameter is being used. *Driven by the motor pully, the three pully system allows the belt which is constantly tensioned a higher degree of torque at the same motor rating. *When working with Scoth-Brite disks or belts or with felt polishing belts, the drive can be infinitely adjusted even for speeds as low as 3 mtr. /sec. Due to the advantages offered by the 3-contact point system, any required surface finishing is possible using contact disks from 50 to 400 mm, contact rolls or contact rollers from 15 to 50 mm, contact belts of 6 or 30 mm width, polishing brushes, polishing disks and polishing belts.