Parallel lathe

1 MAI SPL 1250x6000

Condition: good (used), Year of construction: 2008, turning length: 12,000 mm, spindle motor power: 60,000 W, total height: 3,800 mm, total length: 23,000 mm, total width: 7,600 mm, swing diameter over cross slide: 1,520 mm, turning diameter over bed slide: 1,140 mm, workpiece weight (max.): 20,000 kg, overall weight: 58,000 kg, Equipment: documentation/manual, CNC Lathe Giuseppe Giana - GGH 1100/760 x 12.000 CNC MACH-ID 9439 Make: Giuseppe Giana Type: GGH 1100/760 x 12.000 CNC Control: Siemens 840 D-SL Year: 2008 3 bed way construction Bed width 1100 mm 3 x C-Type Steady rest on lower base with in feed 2 x Fixed steady rest 300 - 800 mm with 5 ton 2 x Chip conveyor 4 Chuck 1000 mm Barafuldi 4 way turret head Isdpfx Aoyl Uh Sepheih Swing over bed Ø: 1520mm Swing over cross slide Ø:1140mm DBC Turning Length: 12000mm Spindle bore: 155mm Spindle power: 60kW Bed width: 1100mm Tailstock spindle Ø: 310Ø Stroke pinole: 300mm Spindle taper: 1:4 taperMk Workpiece weight: 20000 Power: 80A Speeds / ranges: 0-800Rpm Feed rate X-Axis: 0-8000mm/min. Feed rate Z-Axis: 0-8000mm/min. Length: 23000mm Width: 7600mm Height: 3800mm Weight: 58000kg

Condition: used, WEBSTER & BENNETT EV 36” HIGH SPEED VERTICAL BORER MAKE WEBSTER & BENNETT, MADE IN ENGLAND MODEL EV 36” TABLE DIA 915 mm SWING 1168 mm HEIGHT UNDER RAIL 533 - 1016 mm SPEED 13.5 - 300 rpm FEED RATE 0.005-0.250 inch/min MAIN SPEED 40 HP PLUS Iisdpfxsxp Na Nj Aphoh HIGH SPEED TAABLE EV SERIES MACHINE ELEVATING RAIL SAFETY GAURDING SET OF JAWS FULLY FUNCTIONAL GOOD SLIDES

Condition: used, turning diameter 1.600 mm max. swing diameter 1.700 mm control SIEMENS - 840 D Iedpfx Ajvp Shgjpheih faceplate turning speed range 1 - 320 U/min rapid traverse 3.000 mm / min feed range 1 - 3.000 mm/min size of pallet 1.168 mm numbers of pallets 2 main drive 55 kW Vertical turret lathe with cnc | SCHIESS MOWEG - BERTHIEZ TFM 125 has been overhauled by SCHIESS MOWEG (RETROFIT) in 2007. The machine video from the production plant will be shared on request. The machine is in very good condition and was in operation at an aviation company until recently. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: TFM125 | TFM-125

Year of construction: 2010, condition: ready for operation (used), - USED - CNC DOUBLE RAM VERTICAL LATHE MAX ROTATING DIAMETER: 3000 mm Isdpfx Ajyyrh Hjpheih MAX TURNING HEIGHT: 800 mm MAX TURNING DIAMETER: 2800 mm SPINDLE: 1-160 rpm; 71-114 kW; 68500 Nm; 2500 mm X-AXIS TRAVEL: -150+1780 mm Z-AXIS TRAVEL: 900 mm RAPID FEEDS X-Z: 8 - 10 m/min TOOL MAGAZINE: BASKET-TYPE ; TYPE CAPTO C5; 24 POS. POS CONTROL UNIT: SIEMENS 840D MAX ADMITTED LOAD: 15000 Kg WEIGHT: 54000 Kg ACCESSORIES: SWARF CONVEYOR ; TOOL SETTER ; AUTOMATIC DOOR ; HEAD COOLING SYSTEM ; TOUCH PROBE ; PORTABLE HANDWHEEL

Condition: good (used), travel distance X-axis: 12,000 mm, travel distance Y-axis: 7,300 mm, travel distance Z-axis: 3,000 mm, total length: 30,000 mm, table length: 12,000 mm, table width: 4,730 mm, total width: 12,000 mm, total height: 10,475 mm, table load: 250,000 kg, overall weight: 400,000 kg, Make : Waldrich - Siegen - Typ : PF-F-150(1)-530/400 - No. : 11.093/0 - Age : Overhault 2004 ( Euro 2.2 Mil) X Travel : 12.000 - Y Travel : 7.300 - Z Travel : 3.000 - W Travel : 4.000 - Between column : 5.000 - Table width : 4.730 - Table length : 12.000 - Table load : 19 t / mtr. Ca. 250 ton - Table feed : 10.000 mm/min. - W axis : 3.000 mm/min. - T axis : 6.000 mm/min. - Cross adj. milling head : - Vert. adj. cross rail : - Horizontal hydrostatic spindle ram - Milling spindle Ø : 560 - Milling tool taper : iso 60 - C axis feed : 5.000 mm/min. - Milling motor : 90 kW - Spindle speed : 2.500 R/pm - Z axis stroke : 3.000 - Z axis feed : 2.000 mm/min. - Milling Küma Angle head WF2 90 kw- 450 - Milling Küma Uni. UB1D 60 kw - 2400 - Milling Küma Fixed GB1D 90 kw- 2400 - Milling Küma Angle head WF1? - Electric requirement : 3 x 400 V / 50 Hz - Power requirement : 600 kVA / 630 Amp - Capacity 4.000 L coolant true spindle 20/40 Bar Machine is rebuild in 2004 by Schiess Bed – Table assembly group: * Renewal of sliding lining * Grinding of guideway * Renewal of table drive * Direct linear measuring syst. * Hydrostatic Portal and cross rail: * Modification of adjusting spindle trape Zoidal spindle was recplaced with ball screw * Direct linear measuring syst. * New drive motors for relization of higer speed on feed axes of milling support. * New milling support with hydrostatic guideways Electric system: * Complet elctric cabinet switchgear * Complet new wire * Siemens Sinumrik 840 D in 6 axis !! Equipment / parts : * Complet new raumag janich covers * Complet new double chip conveyor * Complet with big tooling packet * Complet with big mounting equipment - Under power in Europe - Free directly - Controlled axis X / Y / Z / W / C / B axis Iodpfxsytrxks Aphjih - Over all height : 10.475 mm - Over all width : 11.934 mm - Over all length : 30.000 mm - Total weight : ca. 400.000 Kg Rebuild in 2004 for EUR 2.200.000 !This CNC Waldrich Portal milling machines was used in the Energie Field for steam turbien case machining. Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: ready for operation (used), functionality: fully functional, turning diameter over cross slide: 550 mm, spindle bore: 77 mm, turning diameter over bed slide: 800 mm, GURUTZPE lathe model Super AT 400/6000, 6,000 mm between points, turning on bed 820 mm, on carriage 550 mm, shaft diameter 76,5 mm, 16 speeds from 9-500rpm, has fixed rear Steady , , has 4 independent claws chuck diameter 800mm, , very good condition in general Ijdpfx Apjwd D Itshjih

Condition: used, Year of construction: 1979, functionality: fully functional, machine/vehicle number: Ob 21882, spindle speed (max.): 700 rpm, feed length X-axis: 15,000 mm, feed length Y-axis: 5,150 mm, feed length Z-axis: 1,600 mm, total width: 6,400 mm, total length: 19,300 mm, total height: 10,370 mm, feed length W-axis: 2,000 mm, spindle diameter: 250 mm, table height: 400 mm, table length: 8,000 mm, table width: 5,665 mm, overall weight: 137,000 kg, year of last overhaul: 2006, grinding spindle motor power: 83,000 W, type of input current: three-phase, We offer for sale a Škoda W250H floor boring machine. This machine is designed for machining heavy and large-sized components for the energy, shipbuilding, metallurgical, mining, and machine production industries. The machine is equipped with a Siemens Sinumerik 840D control system, enabling the execution of demanding boring, drilling, and milling operations. Isdpfx Aszrwq Iephsih Complete technical documentation is available. Upon request, we can provide additional photos, videos, and information regarding the machine's equipment and technical condition. Standard equipment: Tool and measuring instrument storage rack, mounted on the spindle box. Optional equipment: Cooling system with coolant Rotary table 4000x3550 3 x angular heads

Condition: excellent (used), Year of construction: 1970, functionality: fully functional, I am selling this machine, it is connected and can be tested. A video of the machine can be sent via WhatsApp. Diameter over the bed: 1250 mm Diameter over the carriage: 900 mm Iisdpfjxwqk Ejx Apheh Turning length: 6000 mm Workpiece weight between centers: 14,000 kg

Condition: used, Year of construction: 2002, feed length Y-axis: 1,200 mm, feed length Z-axis: 900 mm, Make: Daewoo-Doosan Model: PUMA V-1200M Category: Vertical CNC Turning Center Year of manufacture: 2002 CNC Control: FANUC Series 18-T Machine weight: 23,000 kg Machine dimensions Length: 8,500 mm Width: 4,900 mm Height: 5,650 mm Capacities Maximum turning diameter: Ø 1,600 mm Maximum machining diameter: Ø 1,600 mm Maximum machining height: 1,200 mm Maximum load on spindle: 6,000 kg Main spindle Chuck diameter: Ø 1,200 mm Spindle speed: 2 ÷ 320 rpm Number of ranges: 2 Motor power: 37/45 kW (continuous / 30 min) Powered spindle (RAM) Tool holder: ISO-50 Speed: 15 ÷ 1,500 rpm RAM section: 240 × 240 mm Travels X-axis: 1,200 mm Z-axis: 900 mm C-axis: 360° (minimum resolution 0.001°) Feed rates Rapid traverse X/Z axes: 10,000 mm/min Working feed rate X/Z: 3,000 mm/min Turret Number of stations: 16 Tool holders: BT-50 Drawbar type: 403 P50T-I Maximum tool diameter: Ø 400 mm Maximum tool length: 450 mm Maximum tool weight: 50 kg Maximum tool weight in the magazine: 600 kg Accessories Iisdjziavnopfx Apheh Chip conveyor Coolant tank with washing pumps Spindle line cooler Powered and fixed tool holders Manuals, electrical diagrams, and CE Declaration.

Condition: used, Year of construction: 1971, core drilling diameter max. 50-355 mm bore depth 4000 mm swing diameter 1000 mm centre height 500 mm full boring 18-100 mm main spindle bore 163 mm turning speeds 56-710 U/min workpiece weight 6,3/10 t Tailstock 70-600 mm Drill pipes, guide block, drill head, rolling steady rest, support bearing drill heads, jaws 21- 240 mm, Holder, tools, shelves, cupboards The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. Iiedpfx Apjyt Rz Dsheh We look forward to your visit. Your Markus Hirsch Team