Slitter-Rewinder

DCM ATN Leopard LMA

Technical data:

Maximum parent roll width: 1420 mm
Minimum parent roll width: 600 mm
Maximum parent roll diameter: 1500 mm
Maximum parent roll weight: 2500 kg
Maximum unwinding tension (Ø1500 mm): 600 N
Minimum unwinding tension (Ø1000 mm): 40 N
Minimum standard slitting width: 100 mm
Maximum rewinding width: 1400 mm
Maximum rewinding diameter: 1050 mm
Maximum rewinding weight:
• Ø76 mm shaft: 600 kg
• Ø152 mm shaft: 1000 kg
Maximum rewinding tension: 600 N
Maximum production speed: 600 m/min
Power supply: 3 x 400V 50Hz
Installed power: 30 kW
Compressed air: 6 bar, dry
Compressed air: 5–40°C
Noise level: 82 dB(A)
Iodpfjxx Tbcjx Ad Detp
Color: Grey RAL 7035

Materials to be slit:
• Paper-/liner-based packaging laminates.
• Board from 80 to 300 g/m².

Unwind section:
A separate between-centers unwinder, type T9, 1500 mm diameter, including:
• Hydraulic cylinder for lifting parent rolls from the floor.
• Two motors driving the unwind roll, controlled by an ultrasonic diameter sensor and a tension-control dancer roller.
• Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3") cores.
• Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6") cores (mounted on the pneumatic end adapters).
• Floating edge-correction roller.
• Automatic web guiding system, FIFE DP20, with SE26A photoelectric sensor, ±100 mm correction via electric actuator — for controlling sheet edge or continuous printed line.
• Connecting walkway, enabling web threading at floor level while maintaining full access to the slitting station.
• All web path rollers are anodized.
• Safety guarding for operator protection.

Slitting section:
A slitting station with individual pneumatic knives and circular counter-knives:
• Shear cutting performed against the counter-knives.
• Counter-knife shaft driven by an independent motor; counter-knife shaft is pneumatic.
• Pneumatic knife holders mounted on a beam with dovetail guide (TIDLAND) and an air supply manifold for individual activation.
• 10 slitting sets, each including: Individual TIDLAND pneumatic knife holder (25 mm width) and double-bevel circular knife Ø 90/60 mm.
• Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm length.

Web separation section:
• Separator roller, driven by the slitting motor; angle and curvature fully adjustable.

Lay-on roller:
• Lay-on roller made of anodized ground aluminum or polyurethane (depending on processed materials).
• Pressure is adjustable and synchronized with the winding diameter.
• Roller is removable.

Automatic splicing / transverse cutting system:
• Hydraulically operated pivoting arm including a linear transverse knife and backing plate for securing the web to new cores.

Trim extraction system:
• Trim suction unit with two width-adjustable nozzles.
• Turbine enclosed in a sound-insulated cabinet, conveying trim to a central system or container (not included).

Rewinding section:
• Motorized turret (two-position) with two rewinding shafts.
• Rewinding shaft drive via oversized asynchronous motor.
• Hydraulic centering point for the active rewinding roll.
• Two pneumatic expanding shafts Ø76 mm (3”), max load 600 kg each, featuring full-width rubber strips with individual bladders.
• Two pneumatic expanding shafts Ø152 mm (6”), max load 1000 kg each, also equipped with full-width rubber strips and individual bladders.

The listing was translated automatically. Translation errors are possible.