DEMAG Overhead Crane – 16 Tons Capacity – Year 2018

DEMAG

Condition: excellent (used), Year of construction: 2008, Injection Moulding Machine DEMAG System 800/1120-9500 Basic Information Manufacturer: DEMAG Model: System 800/1120-9500 Year of manufacture: 2008 Clamping Unit Clamping force: 8,000 kN Platen dimensions (horizontal × vertical): 1620 × 1500 mm Tie bar spacing (horizontal × vertical): 1120 × 1000 mm Minimum mould height: 500 mm Maximum mould height: 1050 mm Maximum distance between platens: 2080 mm Opening stroke: 1030 mm Ejector stroke: 350 mm Ejector force: 139 kN Maximum mould weight: 7,200 kg Injection Unit Screw diameter: 130 mm Injection volume: 7,300 cm³ Shot weight (PS): 6,640 g Maximum injection pressure: 1,300 bar Screw length: 20 L/D Electrical & Hydraulic Equipment Rated pump motor power: 110 kW Heater power: 79 kW Hydraulic oil tank capacity: 1,300 l Machine Dimensions and Weight Machine dimensions (L × W × H): 12.3 × 2.7 × 2.7 m Machine weight: 33,500 kg Control cabinet weight: 9,700 kg Optional Energy Saving System ESS (Energy Saving Systems) The machine can be equipped with the modern ESS servo drive system, which increases the energy efficiency of hydraulic plastic injection moulding machines. The system controls the operation of the hydraulic pump motor via a frequency inverter, adjusting the motor’s rotational speed to the current demand during the production cycle. As a result, electrical energy is consumed only during the actual machine demand. Key Advantages - Up to 30% reduction in electricity consumption - Servo drive technology for the hydraulic pump - World-class and proven technology used in the plastics processing industry Godeyugctopfx Aafsip - Reduction of energy losses during idle operation - Lower heating of the hydraulic system - Longer service life of hydraulic components - Possibility of installation on existing hydraulic injection moulding machines The ESS system enables a significant reduction in machine operating costs while maintaining full production parameters.

Condition: excellent (used), Year of construction: 2008, DEMAG Injection Moulding Machine System 1500/1500-16000 Basic Data Manufacturer: DEMAG Model: System 1500/1500-16000 Year of manufacture: 2008 Clamping Unit Clamping force: 15,000 kN Dimensions of mounting plates (H × V): 2150 × 1880 mm Clearance between tie bars (H × V): 1500 × 1250 mm Minimum mould height: 700 mm Maximum mould height: 1400 mm Maximum opening stroke: 2900 mm Injection Unit Screw diameter: 145 mm Injection volume: 10,981 cm³ Injection weight (PS): 9,880 g Maximum injection pressure: 1454 bar Electrical and Hydraulic Equipment Rated pump motor power: 165 kW Heater power: 97 kW Machine Dimensions and Weight Net machine weight: 74 t Control cabinet weight: 21 t Total weight: approx. 95 t Dimensions (L × W × H): 14.4 × 3.4 × 2.9 m Service History / Repairs 2010 – new screw with RSP and barrel 2015 – new IBED 2015 – new wiring board 2017 – new motor and pump no. 2 2017 – new injection cylinder rod BS with seals 2017 – replacement of oil cooler circulation pump 2017 – replacement of TeachBox (robot) 2018 – replacement of pumps P1 + P3 (at 65,800 h) 2018 – hydraulic oil change Optional ESS (Energy Saving Systems) The machine can be equipped with a modern ESS servo drive system, which significantly improves energy efficiency in hydraulic plastic injection moulding machines. The system controls the operation of the hydraulic pump motor through a frequency inverter, which adjusts the motor speed to the machine’s actual demand during the production cycle. As a result, electricity is consumed only when it is truly needed. Main Benefits - Up to 30% reduction in energy consumption - Servo drive technology for hydraulic pumps - Global quality and proven technology used in the plastics processing industry - Reduced energy loss during machine idle time - Lower heating of the hydraulic system - Extended service life for the motor and hydraulic components - Option for installation in existing hydraulic injection moulding machines The ESS system allows significant reduction of machine operating costs while maintaining full production performance parameters. Giedpfx Aaoyugalsfep

Condition: good (used), Year of construction: 2011, functionality: fully functional, travel distance Z-axis: 1,500 mm, Equipment: documentation/manual, Number of axis: 3 Reach: 1500 mm Payload: 5 kg X=420mm Y=1200mm Z=1500mm Gsdpjyfhw Hjfx Aafoip c= 0-90 pneumatic

Condition: good (used), functionality: fully functional, Year of construction: 1992, main lifting speed: 12,000 mm/min, fine lifting speed: 2,000 mm/s, -KOM 3160- Offered here is a Demag industrial lifting crane. This crane can lift loads up to 80 kg. In addition to the crane, you will receive the corresponding motor unit including the chain hoist, consisting of the chain and hook block. The dimensions can be found in the last image. The inspection logbook will be provided upon purchase. Type: PM V8 V1 F6 Year of manufacture: 1992 Number of load strands: 1 Main lifting speed (m/min): 12 Fine lifting speed (m/min): 2 kW: 0.2 / 0.03 Giedsxcnmnspfx Aafjp Protection class: IP 54

Condition: good (used), functionality: fully functional, -KOM 3161- Offered here is a Demag lifting crane. The crane can lift up to 80 kg. In addition to the crane, you will receive the corresponding motor unit including the chain hoist, consisting of the chain and hook block. The dimensions are shown in the last picture. You will receive the inspection book upon purchase. Unfortunately, the nameplate of the drive unit is no longer available. Gisdpfx Aoxcnvpeafjp

Condition: refurbished (used), DEMAG DH 316 H12 Gedoytp Ehjpfx Aafoip Load capacity: 3.2 t Hook lift height: 12.0 m

Condition: excellent (used), functionality: fully functional, DEMAG Hoist Unit P400 P600 P1000 total 24 items - Fine travel gear FG - Main hoist motor - Housing - Wire rope drum - Rope guide - Brake good condition, partly top used to like new Gedpev Uvubsfx Aafjip Info: 20,000 DEMAG spare parts and components in stock! demag parts ware house

Condition: new, functionality: fully functional, crane hoist parts for hoist type DH500 / DH1000 Lifting motor KBH140 B4 Lifting motor KBH140 B2/12 Giodsv Uu T Nopfx Aafep Lifting motor KBH160 B4 Lifting motor KBH200 B4 for hoist P-Zug Lifting motor 24/10 K4P Lifting motor 24/14 K4P Lifting motor 28/12 K4P Lifting motor 36/20 K6P Lifting motor 36/24 K6P Fine reduction gear FG08 FG10 Wire rope drums, casing, rope guides Info: We have over 20,000 DEMAG spare parts in stock! Check out my other offers from our warehouse inventory!

Condition: excellent (used), functionality: fully functional, DEMAG P2000 / P1600 25t Main hoist motor 36/24 K6P 36/20 K6P, fine travel FG 35, wire rope guide, rope drum, drum shell, hoisting gearbox Significantly below manufacturer's list price Top condition Also suitable for P1000 / P1200 P600 P400 P200 Giodpfx Aajv Uvvfsfjp Info: We have over 20,000 DEMAG spare parts in stock! Over 20,000 DEMAG spare parts in warehouse! Be sure to check my other offers from stock!

Condition: ready for operation (used), Year of construction: 2013, operating hours: 27,551 h, clamping force: 2,200 kN, total height: 2,100 mm, This SUMITOMO SHI DEMAG IntElect 220/610-750 smart was manufactured in 2013. It's an electrical injection moulding machine known for its precision and efficiency. Ideal for those looking to enhance their production capabilities with reliable technology. Contact us for more information. Additional equipment • Sepro Robot SDR 22 Machine Benefits Technical Machine Benefits • Screw diameter: 45 mm / screw geometry: standard / l/d ratio: 20 / specific injection pressure: 2150 bar / maximum shot volume: 329 cm³ / maximum shot weight: 293 g / injection rate without accumulator: 254 cm³/s Giodpfsx D Hnysx Aafsp • Dosing stroke: 207 mm / maximum nozzle stroke: 450 mm / nozzle immersion depth: 20 mm / nozzle contact force: 58 kn / number of heating zones: 4 / hopper capacity: 50 l / maximum injection speed: 160 mm/s • Holding force: 2420 kn / maximum opening stroke: 550 mm / minimum mold height: 300 mm / maximum mold height: 580 mm / maximum platen distance: 1130 mm • Mold clamping plates (hxv): 880x830 mm / clearance between tie bars (hxv): 610x560 mm / ejector stroke: 150 mm / ejector force: 58 kn • Dry cycle time according to euromap 6 (stroke): 427 mm • Net weight without oil: 10100 kg Dimensions Machine Depth 6460 mm