Archiveo Sp zo.o

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Hodpfezdn H Rox Ac Nefh Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), year of last overhaul: 2025, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Hodpfjzdny Rsx Ac Njfh Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2025, volume flow: 410 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. Hfsdpfx Ajzdnxgsc Nsh The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2005, operating hours: 24,500 h, functionality: fully functional, Manufacturer Avermann Typ AVOS 1810S-90/100 Year of construction 2005 Hours of operation 23,100 h Quantity of pressed bales 16,163 piece Press power main press 100 tons Specific press capacity 121,2 N/cm² Feed channel 1,000 x 1,800 mm Capacity per cycle time 1,35 cm³ Theoretic cycle time 12,5 sec. Bale size 1,100 x 750 mm Driving motor 2 x 45 kW Connected load 130 kW Tying system 5 fold vertical, full automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 12,2 tons/h bulk weight of 50 kg/cbm approx. 16,0 tons/h bulk weight of 100 kg/cbm approx. 23,2 tons/h Bale weight 500 up to 800 kg, depends on material and bale length Volume hydraulic oil tank 2,000 l SPS controller (manuf., type) Siemens SIMATIC S7-300 Transport dimensions only baler 11.200 x 2.355 x 2.700 mm (without feeding chute) Machine weight baler approx. 24,5 tons Hfedpfxjzc Rhvo Ac Nsh Accessories: ruffler and special press ram

Condition: good (used), Year of construction: 2015, operating hours: 1,932 h, functionality: fully functional, Bale press Presto CC 50 M, year of manufacture 2015, with lifting and tilting device. Technical data: Manufacturer: Presto Type: CC 50 M Hfjdpfszc Hz Ejx Ac Noh Year of manufacture: 2015 Operating hours: 1932 Pressing force: 50 t Cycle time: 52 s Drive power: 7.5 kW Feed opening: 1030 x 1100 mm Feed volume: 0.85 m³ Tying: 3-wire, manually Throughput at a bulk density of: 35 kg/m³ - 1.3 t 60 kg/m³ - 1.7 t 100 kg/m³ - 2.2 t Bale dimensions: 750 x 1100 mm Bale weight: 300 kg Dimensions: 4705 x 1680 x 2540 mm (L x W x H) Machine weight: approx. 4000 kg Materials: Paper, cardboard, film The operating manual is available in German. Note: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video on our website or our YouTube channel. Please note: All technical data refers to the manufacturer's specifications. We assume no liability for the information provided or any errors. This offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Baler Presto CC 40 M, Year of manufacture: 2017 Technical Specifications: Manufacturer: Presto Model: CC 40 M Year of manufacture: 2017 Pressing force: 40 t Cycle time: 34 s Drive power: 15 kW Feed opening: 1080 x 1100 mm Feed volume: 0.85 m³ Binding: 4-fold, polyester strapping, manual Hjdpfxjzc Hy Ue Ac Njfh Throughput rate at bulk density of: 35 kg/m³ - 1.8 t/h 60 kg/m³ - 2.5 t/h 100 kg/m³ - 3.1 t/h Bale size: 750 x 1100 mm Bale weight: 400 kg Dimensions: 3650 x 1590 x 2010 mm (LxWxH) Machine weight: approx. 3,800 kg Materials: Paper, cardboard, film The baler is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Operating instructions and CE declaration are available. Note: Channel discharge is fully automatic and regulated. Please note: All technical data is based on the manufacturer's information. We do not accept liability for the information provided or any possible errors. This offer is non-binding, subject to prior sale, and may be revoked at any time. Inspections are possible by appointment. Sale is ex-works, prepayment required, without warranty or guarantee.

Condition: good (used), Year of construction: 2019, functionality: fully functional, Bale press Dixi 80 SLD, year of manufacture 2019, with lifting/tilting device Manufacturer: Dixi Type: Dixi 80 SLD Year of manufacture: 2019 Drive power: 11 kW, 400 V / 32 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Press cycle: approx. 35 s Capacity: approx. 1000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. This offer is non-binding, subject to prior sale, and can be revoked at any time. Hjdezc Hyuspfx Ac Nofh Inspections are possible by appointment. The sale is made against advance payment, ex works, without warranty.

Condition: ready for operation (used), Year of construction: 1994, Brand: HSM Model: 155 VL Hodpfszc Hhxsx Ac Nefh Year of construction: 1994 Pressing force: 157 kN Voltage: 400 Max. bale weight: 250 kg Bale dimensions: 110 x 70 x 95 cm Machine weight: 950 kg Machine dimensions: 144 x 100 x 234 cm Feed opening dimensions: 110 x 59 cm

Condition: good (used), Year of construction: 2012, functionality: fully functional, Strautmann bale press, type BaleTainer, pressing force 60 t, year of manufacture 2012 Technical data: Manufacturer: Strautmann Umwelttechnik Type: BaleTainer Year of manufacture: 2012 Pressing force 60 t Total connected power 30 kW Bale dimensions 1,100 x 1,100 x 800 mm (W x D x H), 3 straps Bale weight up to 400 kg (3 straps) Binding: 4-fold vertical Dimensions: 5,348 x 2,113 x 2,752 mm (L x W x H) Weight approx. 7,280 kg Materials: Paper, cardboard, PET bottles, film Note: The press is in good working order and has been inspected and tested. A video can be found on our website or YouTube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any errors that may occur. The offer is subject to change, subject to prior sale, and may be withdrawn at any time. Inspections are possible by arrangement. Hfodpfx Ajzcuz Tec Nsh The sale is made against advance payment, ex works, without any warranty.

Condition: ready for operation (used), Year of construction: 2015, Make: HSM Model: V-press 860 plus Year of manufacture: 2015 Press force: 418 kN Voltage: 400 Max. bale weight: 480 kg (depending on the material) Bale dimensions: 120 x 120 x 78 cm Machine weight: 2083 kg Machine dimensions: 180 cm x 125 cm x 298.5 cm Feed opening dimensions: 120 cm x 65 cm Hfsdpfx Acezcrhks Neh Video of the machine in operation available upon request. Fast delivery possible.

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Equipment: documentation/manual, HSM HL 7009 Re / Li horizontal baler. The machine is in very good condition and regularly serviced by an authorized service center. This baler is designed for larger waste disposal projects in retail outlets and small and medium-sized central warehouses. Bales from the HL 7009 model have a cross-section of 1100 x 1100 mm and, with a bale length of 1200 mm, can weigh up to 600 kg, ensuring optimal utilization of the truck's payload. Pressing force: 700 kN Specific pressing force: 58 N/cm² Drive power: 10.5 kW Voltage / frequency: 400 V / 50 Hz Idle capacity (theor.): 42.97 m³/h Loading opening width x length: 890 x 1020 mm Hsdpfjzck Uiox Ac Nofh Bale width x height x length: 1100 x 1100 x 1200 mm Total length x width x height: 5366 x 2525 x 2559 mm Bale weight: 600 kg

Condition: ready for operation (used), Year of construction: 2009, Well-maintained PRESTO HPK 50 BSK automatic horizontal baler in fully operational condition. The machine has been in continuous industrial use and has been regularly serviced and professionally maintained throughout its lifetime. It was recently dismantled from operation due to plant modifications and is ready for transport and immediate recommissioning. Suitable for baling: Cardboard (OCC) Paper Mixed recyclables Plastic films PET bottles Packaging waste The HPK 50 BSK is a compact and reliable industrial baler designed for medium to high throughput operations. Its large feed opening allows efficient loading by conveyor, wheel loader or excavator. The fully automatic wire tying system ensures consistent bale quality and low operating costs. The PRESTO HPK series is well known throughout Europe for durability, simple maintenance and reliable operation. Hjdpfx Aozcdrnjc Nefh Pressing force: 50 t Motor power: 22 kW Power requirement: 400 V / 80 A Feed opening: 1,250 x 1,050 mm Bale dimensions: 1,100 x 700 mm Bale weight: up to approx. 500 kg depending on material Cycle time: approx. 22 sec Throughput: up to 5–10 t/h depending on material density Fully automatic 4-wire tying Machine dimensions: approx. 6,820 x 1,950 x 2,160 mm Machine weight: approx. 8.75 t

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, pressing force: 48 t, bale length: 1,200 mm, bale width: 750 mm, bale height: 1,100 mm, bale weight: 550 kg, Equipment: documentation/manual, Automatic baler HSM VK 4812 The machine is maintained in perfect condition. The total operating hours are only 1950, and it has processed just 1314 bales of material. The machine was regularly serviced and has operated indoors in a warehouse since new. The baler has worked almost exclusively with non-abrasive material – textile offcuts. Key advantages of the unit: - Actual throughput: 6–13 t/h - Optimal continuous operation: 6–10 t/h - Very fast cycle time → ideal for use with conveyor lines - Significantly superior to the 15–22 kW version when processing a high material stream Technical data: Pressing force: 480 kN (≈ 48 tons) Motor power: 30 kW Connected load: approx. 32 kW Power supply: 3 × 400 V / 50 Hz Hfsdpfx Ajzb H E Uoc Neh Specific pressing force: 58.2 N/cm² Volumetric throughput: up to 332 m³/h Practical weight throughput: approx. 6 t/h (20 kg/m³) approx. 13 t/h (50 kg/m³) Theoretical (maximum) throughput: up to 16.6 t/h at 50 kg/m³ Idle cycle time: approx. 11.2 s Bale dimensions: 1100 × 750 × 600–1200 mm Bale weight: up to approx. 550 kg Pressing channel: 1100 × 750 mm Filling opening: approx. 1020 × 1250 mm We also have other balers in stock. Transport costs depend on weight, volume, and most importantly, distance. When making inquiries, please provide the following details: Delivery address (postal code and town/city name). For further details and transport options please contact us by phone, as additional arrangements require direct contact. Our contact details are available in the seller's legal information. We sell and export worldwide; thanks to our extensive warehouse capacity, we can flexibly and quickly supply larger quantities as well. We issue intra-community invoices – VAT-free. Opening hours: Mon–Fri: 08:00–16:00 Sat: closed

Condition: good (used), Year of construction: 1990, Roll compactor, Bergmann – used: Price ex works: only €950 (net) Manufacturer: Bergmann Type: PS 8100E Year of manufacture: 1990 Serial number: 05 3658 2845/90 Pressing pressure: to Weight: 750 kg 400V, 5.5 kW Hodpfx Acezbygrj Njfh Condition: good Available: from Q4/2026 Location: Hamburg Efficient waste compaction: A special steel drum enables effective collection, shredding and compaction of the waste, reducing its volume up to ninefold. Continuous filling: The machine allows for continuous filling by all users. The feed shaft can also remain open during the working process, which facilitates and accelerates waste compaction.

Condition: good (used), Year of construction: 1999, Baling presses, HSM, 30-ton pressing force – used: Price ex works: only €2,950 (net) Manufacturer: HSM Type: 225.1 VL Year of manufacture: 1999 Machine number: 6124.834. N Serial number: 200014505 Pressing force: 30 tons 400V, 5.5kW Hjdpjzbygfofx Ac Nsfh Condition: good Available: from Q4/2026 Location: Hamburg

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Hfjdpfx Aszbxwisc Neh Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 60 t, Equipment: documentation/manual, Used HSM V-Press 1160 Plus vertical press from 2015. The device is regularly serviced by an authorized service center. The press is fully functional and in very good technical and technical condition. Crushing force: 594 kN Voltage / required: 400 V / 50 Hz Hjdpfjzbrxgsx Ac Njfh Width x height of the loading opening: 1195 x 650 mm Bale length x width x height: 1200 x 1100 x 1200 mm Width x height x height of the machine: 1780 x 1568 x 2985 mm Machine weight: 2403 kg Pressed material: foil, mixed paper, cardboard, cutting machine waste Freight costs depend on the weight, volume and above all on the distance, the following information is relevant for inquiries: Delivery address (postcode and name of the town), but further details require a telephone call, so we ask you to inquire about transport costs and other delivery modalities to contact us by phone. Our contact details can be found under the legal information of the seller. We sell and export worldwide, due to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-community invoices - excluding VAT. Opening hours Mon-Fri: 8 a.m.-4 p.m. sat .: closed

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Hsdpfx Acozaqyme Nofh Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request. Transportation is also possible.

Condition: excellent (used), Year of construction: 2015, Equipment: documentation/manual, HSM HL 4010 Re / Li horizontal baler. Equipped with a loading tipper for the basket. Manufactured in 2015. Very good condition - regularly serviced by an authorized service center. Ready for use. Available for binding with wire, string, or polypropylene tape. Semi-automatic baler system with a 40-ton pressure for economical volume reduction of residual (recyclable) materials in industry and retail: Cardboard Tetra packs Films Hfodpfxozaqlce Ac Neh Foams PET bottles Insulation mats and other compressible materials. Press force: 400 kN Transport width: 1,767 m Transport height: 2,489 m Transport length: 5,573 m Weight: 4,500 kg Drive power: 7.5 kW Bale weight (depending on material): 300-350 kg Bale length x width x height: 750 x 1200 x 750

Condition: ready for operation (used), Year of construction: 2013, Brand: HSM Type: V-Press 1160 plus Year of manufacture: 2013 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Hodpfxsy Uimvj Ac Nofh Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feeding opening dimensions: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, pressing force: 48 t, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 450 kg, Equipment: documentation/manual, HSM VK 4812 P Year of production: 2017 Fully automatic baler. The device has service and maintenance work by an authorized HSM service with a branch in Germany. Press after significant service work - details after direct contact. The baler comes complete with a ramp for ejection of finished bales and stands for binding wires. Pressing force: 480 kN Drive power: 18 kW Voltage / frequency: 400 V / 50 Hz Capacity at 50 kg/m³: 10.2 t/h Bale width x height x length: 1100 x 750 x 600 - 1200 mm Total length x width x height: 6661 x 3994 x 2583 Machine weight: 10.2 t Compressed material: foil, mixed paper, cardboard, die-cutter waste Bale tying: 4-fold with wire We also have other presses in stock. Transport costs depend on weight, volume and, above all, distance, the following information is important for inquiries: Delivery address (postal code and city name), but further details require telephone contact, so please inquire about transport costs and other delivery methods to contact us contact us by phone. Our contact details can be found in the seller's legal information. Hfsdpfx Acsy Udzhs Noh We sell and export worldwide, and thanks to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-Community invoices - without VAT. opening hours Mon-Fri: 8:00-16:00 Sat: closed

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 80 t, bale weight: 600 kg, Equipment: documentation/manual, DIXI 80 SLD horizontal press Hedsy Udwpjpfx Ac Nofh Semi-automatic press system with 80 tons of pressure for economical volume reduction of residual materials (recyclable) in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulating mats and other compressible materials. Pressure force : 80 t Electrical connection : 400 V 50 Hz; 11 kW; D-32 A (option: K-32 A) Cycle – average approx. : 35 sec Length approx. : 4,320 mm (without lifting device and pallet) Width approx. : 1,830 mm Height approx. : 2,620 mm (with hopper) Loading opening (WxD) – housing : 1,040 x 1,110 mm Bale dimensions : 1,120 x 1,120 x 1,200 mm Bale weight approx. : 500 – 600 kg Tying 4 manual, wires with quick-release eyelets Machine weight approx. 8,000 kg (without bale)

Condition: used, functionality: fully functional, Main Technical Specifications Machine Hodoy Uddispfx Ac Nofh Model: COMDEC LV 50-40 PFT horizontal baling press Pressing force: 50 tons Horizontal hydraulic baler for cardboard, paper and industrial waste Electrical data Power supply: 380 V / 3 phase / 90 A Hydraulic motors: 2 × 22 kW hydraulic pump motors Conveyor pump motor Hydraulic system Hydraulic main cylinder: 180 / 150 × 2000 mm Hydraulic pressure control system with oil cooling and filtration Oil tank with pressure and return filters Machine dimensions Total machine length: approx. 8,394 mm Width: approx. 1,920 mm Height: approx. 3,104 mm Functional equipment Automatic wire tying system Bale length control system Hydraulic wire twisting unit Automatic bale ejection system Conveyor control cabinet and electrical automation system Noise level Working noise level below 70 dBA

Condition: excellent (used), Year of construction: 2016, bale weight: 480 kg, For sale: HSM HL 4809I baling press. Hjdpfxoy T Iqdo Ac Nsfh

Condition: used, Year of construction: 2021, functionality: fully functional, For sale: HSM 7009st baler and conveyor belt. Hfedpfx Aey T Inpjc Nsh