Oldach-Maschinen

Year of construction: 2023, condition: used, Used Machine Year of Manufacture: 2023 Features and Technical Specifications: - Stationary, oil-lubricated 2-cylinder piston compressor - Two-stage compression - V-belt drive - Intercooler and aftercooler - Condor pressure switch - Motor protection and safety valve - Tank pressure gauge - Check valve and relief valve Hnsdpozy Dzisfx Ac Aet - Condensate drain valve - Additional connection fittings with blind plugs - Rubber vibration dampers - Manhole opening for tank inspection - Tank compliant with AD-2000 regulations - Suction capacity: 660 l/min - Effective flow rate: 520 l/min - Maximum operating pressure: 10 bar - Motor power: 4.0 kW / 5.5 PS - Power connection: 400 V / 50 Hz - Start type: Direct start - Speed: 1,025 rpm - Vertical, internally coated 270-liter compressed air tank - Air outlet: 3/4-inch female thread with shut-off valve - Sound pressure level: 78 dB(A) - Dimensions: 750 × 705 × 1,800 mm - Weight: approx. 170 kg

Condition: used, Technical specifications: Tank capacity: 500 L Flow rate: 950 l/min Max. pressure: 10 bar Number of pistons: 2 x 2 Power supply: 400 V Engine speed: 2800 rpm Engine power: 2 x 5.5 kW Overall dimensions: Hnedpfxjzvmris Ac Ajt Length: 2100 mm Width: 600 mm Height: 1300 mm

Condition: used, Technical specifications: Tank capacity: 500 l Max. pressure: 10 bar Hsdpfxjzvmmge Ac Aent Number of cylinders: 2 x 2 cylinders Power supply: 400 V Engine speed: 1400 rpm Engine power: 2 x 4 kW Overall dimensions: Length: 3100 mm Width: 650 mm Height: 1300 mm

Year of construction: 2018, condition: used, Compressor system Manufacturer: Atlas Copco Type: GA15VSD+FF Year of manufacture: 2018 Technical data Note: Hodpfszu Al Ajx Ac Asnt The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is not binding.

Year of construction: 2018, condition: used, Compressor with refrigerant dryer Manufacturer: Boge Type: S 111-4 Year of manufacture: 2018 Hnsdszu Alvspfx Ac Ajt Technical data - Volume flow: 17.10 m³/min - Final compression pressure: 10 bar - Motor speed: 1490 min-1 - Motor power: 110 + 3 kW Refrigerant dryer Manufacturer: Boge Type: DS220 Year of manufacture: 2017 Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 2018, condition: used, Screw compressor Manufacturer: Renner Type: RS132D Year of manufacture: 2018 Technical data - Main drive motor: direct drive of the compressor stages via a shaft coupling - Oil filter / thermostat unit: regulates the cooling of the compressor oil and filters it - Oil-injected compressor stage: compressed air generation - Suction regulator: regulates the amount of air drawn in by the compressor - Control cabinet: controls and regulates the compressor system - Suction air filter: filters the air drawn in - Radial fans: generate cooling air for the oil and compressed air coolers - Compressed air outlet: connection point for an external compressed air network - Minimum pressure retaining valve: maintains a minimum system pressure for oil supply, separates network / system pressure - Fine oil separator with oil suction line, sight glasses, and check valve: oil separation via air-oil filter cartridges, return of separated oil from the compressed air - Safety valve: relieves pressure in case of overpressure - Oil filler plug with oil level monitoring: electronic oil level monitoring - Oil drain: drains the oil reservoir - Compressed air / oil combined cooler: cools the compressed air and the compressor oil - Control system: RENNERtronic - Integrated standby heater Compressor - Counterclockwise rotation (without gearbox) / Clockwise rotation (with gearbox) Suction regulator The suction regulator is mounted directly on the screw compressor. It regulates the volume flow of air drawn in by the screw compressor through the suction filter. Operating principle of the suction regulator: The suction regulator has only one main valve. This valve operates as a stepless control valve as well as a tightly closing shut-off valve. In full-load operation, the suction cross-section is fully open with minimal pressure drop. In part-load operation, the suction cross-section is automatically regulated by limiting the stroke and adjusted to the actual air requirement. When the system is stopped, this valve quickly and automatically closes the entire suction cross-section completely. The multiple functions of the regulator are initiated by only one control unit. Minimum pressure retaining valve The minimum pressure valve is located at the compressed air inlet of the air aftercooler. It performs two functions: 1) As a pressure retaining valve, it prevents the pressure from dropping below a minimum overpressure of 4.5 bar when there is no back pressure. This pressure is necessary to ensure the oil supply to the compressor. At the same time, this minimum overpressure is required for good oil separation. 2) As a check valve, it prevents the backflow of compressed air from the compressed air network or the pressure vessel into the compressor system. This allows the separator vessel to be completely relieved when the system is shut down. The valve operates automatically. Adjustment of the minimum pressure valve may only be carried out by personnel authorized by the manufacturer! Hnodjzu Aibepfx Ac Aet Suction air filter The suction air filter is installed in the housing and connected to the suction regulator via a ventilation hose. The micro-dry filter with a fineness of 10 μm is used to filter the suction air. The filter can be cleaned several times before it needs to be replaced. Use only original replacement filters! Pressure transmitter The pressure transmitter, used in all systems with electronic control (RENNERtronic / -Plus), is connected to the compressed air outlet (network press

Year of construction: 2011, condition: used, Compressor system Manufacturer: Atlas Copco Type: GX11FF Year of manufacture: 2011 Hnodpfx Acozuz E Is Aot Technical data Note: The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is not binding.

Year of construction: 2013, condition: used, This machine is offered for sale on behalf of a customer. Viewing is available by prior arrangement. Please contact us through the platform's messaging system for further information and the relevant technical contact details. For inquiries: Zoltán Utasi Plus 36 30 205 7380 • Press table dimensions:ca. 3450 mm long × 1450 mm wide. • Bonding area (electrode area): 3000 mm long × 1300 mm wide. • Maximum workpiece thickness: 130 mm. • The top pressure is provided by 8 hydraulic cylinders with Ø50 mm bore, arranged in two rows. • Side pressure is provided by 24 hydraulic cylinders with Ø50 mm bore, arranged in one row at 144 mm centers. This cylinder arrangement is required to achieve maximum pressure over the entire 130 mm glue line thickness and 3450 mm length. • Side pressure is continuously adjustable. • Recommended side pressure: o Softwood: 18–20 kp/cm² o Hardwood: 20–23 kp/cm² • The hydraulic power unit is equipped with a variable-displacement axial piston pump. • Maximum hydraulic pressure: 200 bar. • The PP sheet covering the press table is replaceable. It protects the expensive aluminum electrode from wear and significantly reduces cleaning time. • The press is suitable for producing laminated timber panels up to 6000 mm long in two pressing cycles. • Motorized loading table with a usable length of 3000 mm, providing easy material handling. • The loading table is equipped with rollers spaced at 250 mm intervals. • The loading table incorporates 4 transverse chain conveyors. During transverse material transfer, their upper level is raised to the roller level by 6 pneumatic cylinders. • The guide rails and drive for the transfer carriage are located above the loading table. • The steel unloading table has a length of 3000 mm. • The unloading table is equipped with rollers spaced at 300 mm intervals. • Material flow is from left to right. The loading table is located on the left side of the press, while the unloading table is located on the right side. • The conveyor-type glue applicator is positioned before the loading table. Conveyor width: 250 mm. Infeed section: 1500 mm long. Outfeed section: 3500 mm long. The glue applicator includes a removable glue reservoir. • A limit switch is installed at the end of the conveyor to prevent workpieces from falling off. • A movable roller table is positioned before the conveyor for applying adhesive to long workpieces. • RF Generator and Electrical Specifications • The integrated 30 kW radio-frequency (RF) generator is capable of curing approximately 2 m² of glued surface per minute when using PVA adhesive and timber with a moisture content of 6–8%. • The RF generator is easily tuned using an adjustable vacuum capacitor. • Power supply: 3 × 400 V, approximately 45 A. • The anode main switch and the control system main switch are located at the front of the press for easy access. Press Control, Monitoring, Operating Cycles and Safety Features • The control panel includes an anode current meter, grid current meter, glue curing timer, cycle indicator lights, press control buttons, fault indicator lamps, and an audible alarm. • The press closes in manual mode using a two-hand safety control system. Hedpfozn N Ecex Ac Ajnt • Equipped with an emergency stop safety system. • The press door includes an alignment cycle to assist in positioning the timber before pressing. Specifications are provided for information only.

Year of construction: 2022, condition: used, Second-hand machine Hedpfxezk Nrze Ac Ajnt Year of manufacture: 2022 Condition: as new, very few operating hours, not used in production Features and technical specifications: - Compact screw compressor with variable speed control and innovative LOGIN control system - With tank and refrigerated dryer - Maximum pressure: 10 bar - Effective delivery rate: 1,050 l/min - Motor power: 7.5 kW - Noise level: 62 dB(A) - Connection: 1/2 - Tank capacity: 270 litres (AD2000) - Frequency-controlled - Electronic control - Oil heat exchanger - Compressed air receiver, hot-dip galvanised inside and out - Drive transmission: Direct coupling - Starting method: Star-delta - Compliant with AD 2000: yes Dimensions: 1,200 × 650 × 1,540 mm Weight: 295 kg Availability: at short notice Storage location: Röllbach

Year of construction: 2009, condition: used, Second-hand machine Environmentally friendly thanks to the use of R404A Energy savings thanks to a rotary refrigerant compressor (20–30% more efficient than (compared to a conventional piston) intelligent drainage system Max. operating pressure: 13 bar compressed air output 5,200 l/min 7,312 m²/hour Motor power 1.58 kW, 230 V Max. inlet temperature 55 °C Dimensions: 557 x 460 x 789 mm Hodpfozk Nrhox Ac Aent Availability: at short notice Storage location: Röllbach

Year of construction: 2015, condition: used, Used Machine Year of Manufacture: 2015 with refrigerated dryer Features and Technical Specifications: - Pressure: 10 bar - Suction capacity: 660 l/min - Speed: 1025 rpm - Tank volume: 270 l - Noise level: 78 dB(A) - Effective flow rate: 520 l/min - Air outlet: 3/4"i - Drive power: 4 kW - Air intake capacity: 660 (l/min) - Drive type: V-belt - Tank design: vertical - Power (kW): 4.0 - Voltage (V): 400 V - Starting method: Direct-on-line (DOL) - Compression type: 2-stage - Dimensions: 750x705x1800 mm - Weight: 170 kg With DK 985 Eco refrigeration dryer: - Airflow at pressure dew point 3 °C: 600 l/min - Power consumption: 0.3 kW - Pressure drop: 0.25 bar - Voltage: 230 V - With automatic condensate drain - Dimensions: 325 x 263 x 745 mm Hodpfx Aozk Nqksc Aent - Weight: 25 kg Availability: available shortly Storage location: DE-63934 Röllbach

Condition: ready for operation (used), Year of construction: 2020, functionality: fully functional, Auction of two Kaeser screw compressors, one Kaeser refrigeration dryer, and one compressed air tank! Screw compressor Kaeser SK 22 Year of manufacture: 2020 Screw compressor Kaeser SK 19 Year of manufacture: 1995 Hjdpfjzktnysx Ac Aent Refrigeration dryer Kaeser TB 26 Year of manufacture: 2016 Compressed air tank Volume: 500 l Year of manufacture: 1986

Condition: good (used), Year of construction: 1992, functionality: fully functional, 1 x screw compressor Make RF 10 YD Hsdpfx Acszgc Sge Aent Year of manufacture: 1992 with refrigerant dryer Renner RKT CQ 0065 Year of manufacture: 2017 + receiver tank OKS 500 liters / max. 11 bar Year of manufacture: 1998 Technical data: max. pressure 10 bar Power: 7.5 kW Air flow rate: 930 l/min Operating noise: 70 dB (A) The system can be inspected while it is running.

Condition: good (used), Year of construction: 2002, functionality: fully functional, overall weight: 700 kg, The 30 kW screw compressor has been disassembled and is ready for shipment. Hedpszb Dq Iofx Ac Ajnt

Year of construction: 2018, condition: like new (used), Atlas Copco GA 5 FF screw compressor including refrigerant dryer. Motor & Performance: • Rated power, main motor: 5.5 kW (7.5 HP) • Motor efficiency: Typically IE3 (protection class IP55) • Voltage / Frequency: 400 V / 50 Hz (3 phases) • Starting method: Star-delta Pressure and Flow Rate: 7.5 bar 15.0 l/s (900 l/min) ~54.0 m3/h 8.5 bar 13.2 l/s (792 l/min) ~47.5 m3/h 10 bar 12.5 l/s (750 l/min) ~45.0 m3/h 13 bar 8.4 l/s (504 l/min) ~30.2 m3/h Tank capacity: 270 l Integrated refrigerant dryer: • Pressure dew point: +3 °C • Additional power consumption: approx. 0.22 kW • Condensate drain: Electronic, loss-free Hnodpsy T Ibvofx Ac Aet Noise Level & Environment • Sound level: 60 to 63 dB(A) (very quiet due to complete encapsulation, installation directly at the workstation is possible) • Permissible ambient temperature: +1 °C to +46 °C Dimensions & Weight: • Length x Width x Height: approx. 1500 mm x 730 mm x 1710 mm • Weight: approx. 360 kg Control: • Type: Elektronikon Operating hours: 1170 h Year of manufacture: 2018 Price: 5000.-

Condition: ready for operation (used), functionality: fully functional, motor power 5,5kW Hnedpfx Ajy N N R Dec Aot tank capacity 300l capacity 35m3/h max pressure 8bar connection 380V

Condition: ready for operation (used), functionality: fully functional, motor power 11kW Hodpfjy N N Rwex Ac Asnt working pressure 10bar capacity 1,59m3/min

Condition: new, Walter Technic Compressor Model: SKTG 5.5 PP Kombo Dryer, Hnodpfxey Nlwte Ac Ast Automatic condensate drain, Tank: 500 litres, Pressure: 10 bar, Capacity: 700 litres per minute, Weight: 505 kg.

Condition: used, Year of construction: 2016, Suction capacity approx. 850 l/min Filling capacity approx. 680 l/min Compressed air tank 10 bar Tank capacity Tank capacity 2 x 100 l Tank surface galvanized Mounted on safety base plate Including refrigerated dryer, fine filter, automatic condensate drain Hnsdpfx Acjy Ifmre Ast

Condition: new, Falke Technik Compressor Model: FKTG 5.5P COMBO Dryer, Automatic condensate drain, Tank: 500 litres, Pressure: 10 bar, Capacity: 700 litres per minute, Weight: 420 kg. Hnedpfxsy H Ipys Ac Aet

Condition: used, Screw Compressor SCHNEIDER AM B7.5 10 – used – ----- Technical Specifications ----- Max. pressure: 10 bar Motor: 7.5 kW Air delivery at 10 bar: 1,000 l/min Weight: 250 kg Operating hours: 6,922 h Load hours: 2,083 h Year of manufacture: 2017 Hodey Dp Swjpfx Ac Asnt

Year of construction: 2018, condition: ready for operation (used), Comp Air screw compressor incl. refrigeration dryer Comp Air screw compressor L 06 Hnodpfx Aoy Amknjc Ajt 5.5 kW Year of manufacture: 2018 10 bar Delivery rate: 0.67 m³/h Refrigeration dryer PT 9

Year of construction: 2026, condition: used, New display machine! Stationary piston compressor with refrigerant dryer, condensate drain, oil-water separator and pre-/fine filter. The universal solution with belt drive and high-quality features. Especially suitable for craftsmen. These compressors are used where compressed air quality, durability, and efficiency are essential. Long service life thanks to two-stage high-performance units with low speed, specially machined cast cylinders for minimal oil consumption and extended lifespan, high-performance valves, optimum cooling via large fan wheel, motor with overload protection, easy condensate drainage using the standard-mounted 1/2" ball valve, standard equipped with Condor pressure switch and manometer, mounted as standard on a safety pallet with anti-vibration mounts. Hedpfxjyw Thvs Ac Asnt Technical data: Suction capacity 650 l/min, output capacity 520 l/min, max. pressure 10 bar, tank volume 270 l, cylinders/stages 2/2, speed 920 min-1, motor power 4 kW / 400 V, weight approx. 197 kg Location: Rieth

Year of construction: 2009, condition: used, Used, top condition, low operating hours Manufacturer: Kaeser Model: Mobil 450 Year of manufacture: 2009 Machine no.: 1781 CE type approved Motor: 2.4 kW, 380V Piston compressor Air output: 450 l/min. Max. operating pressure: 10 bar Mobile With pressure vessel Capacity: 90 litres Max. permissible pressure: 11 bar New price approx. €2,000.00 Hodpfx Acjyr Sk Rj Asnt Required floor space approx. 1300x500x900 mm Total connected load approx. 2.4 kW Location: 97447 Gerolzhofen, loaded free on truck, unpacked Delivery in current condition as inspected, without warranty or liability.

Condition: like new (used), Year of construction: 2013, functionality: fully functional, Vertical piston compressor with sound-dampening hood, DK 600Eco UNM STS 660-10-270 - Year of manufacture: 2013 - With mounted refrigeration dryer, 660 l intake capacity, 520 l delivery rate Hnedpfx Acsypkr Uj Aet - 10 bar - Weight 245 kg - Sound-dampening hood - Condensate drain 4 kW, 400 Volt - Width 960 mm, Depth 740 mm, Height 1905 mm - Noise level 69 dB (A) - Very few operating hours - ABSOLUTELY LIKE NEW - TÜV inspection valid until August 2026, with corresponding inspection certificates Transportation available for an extra charge!