Used Hidralmac Phc for sale (21)

Condition: used, Year of construction: 2016, machine/vehicle number: 4303, pressure:500 t passage width:2100 x 1500 mm stroke:1000 mm total power requirement:62 kW weight of the machine ca.:39 t dimensions:5100 x 2800 x 4040 mm return capacity:40 t Main cylinder:2 Stück column diameter:Hauptzylinder 360 mm Table dimensions:2100 x 1500 with T-Nute mm Ram size:2100 x 1500 mm table height over floor:850 mm pre-running speed:300 mm/sec return speed:300 (bei 20T Stößelgewicht) mm/sec Pressure Speed:200T = 28 mm/sec Helhsdyynveccqmonl Oil Tank Capacity:ca. 1000 l Auxiliary cylinder:2 Stück column diameter:Hilfszylinder 120 mm Total size Table Tops:ca. 2750 x 1600 mm Total size of plunger plates:ca. 2750 x 1600 mm Pressure Speed:300T = 20 mm/sec Pressure Speed:500T = 6 mm/sec Retract force of the plunger:40 t Tension of the control chain:24 V voltage:400 V Frequency:50 Hz Axial piston pump (REXROTH/Bosch A4VSO125):290 lt/min Daylight Opening:1500 mm Hydraulic block:REXROTH pressure control:über PLC (Mindestdruck 50T) Cylinder:4 x ?90 x 70 mm stroke length max.:300 über PLC einstellbar mm Outejection speed forward:95 mm/sec. Outejection speed return:240 mm/sec. Capacity:4 x 15T bei 250 bar t Pressure setting:über Monitor von 50-500T t Pressure constant posture:0-900 sec Hydraulics tank:2000 l Siemens Control System:S7 300 Storage capacity:200 Programme Electronics from German manufacturers:SIEMENS/MÖLLER Tax desk:auf Schwenkarm Light sensors sick:1500 auf der Vorderseite mm

Condition: as good as new (ex-display), Year of construction: 2015, pressure:63 t table length:700 mm table width:1000 mm Hjlhoffamqoccqmjnl weight of the machine ca.:ca. 9 t dimensions of the machine ca.:4500 x 4300 x 2700 m :1 Stück stroke length max.:1200 mm daylight dimension : table/slide up:1200 mm table height:700 mm :um 1200 mm :um 45 Grad :um 170 Grad :1250 x 1000 mm table load:5 t :25 mm/sec pre-running speed:95 mm/sec return speed:80 mm/sec work speed:von 0 bis 10 mm/sec.

Condition: new, Year of construction: 2017, machine/vehicle number: DF0152, pressure:80 t stroke:500 mm total power requirement:12 kW weight of the machine ca.:5,1 t Controll:Zweihandbedienung cylinder:1 work height max.:800 mm working area:800 x 800 mm Table dimensions:800 x 800 mm pestle plate:2800 x 1300 mm table height:800 mm pre-running speed:9,8 mm/sec work speed:9,8 mm/min return speed:18 mm/sec :700 mm Column-Diameter:75 mm :10 kW main drive:WEG 15 kW pump:REXROTH, Parker elektronische Axialkolbenpumpe kW :25 (bei280bar) t :200 mm :30 mm :80 mm/sek. :REXROTH/Parker :REXROTH/Parker :300 L :ca. 250 L :über PLC (Mindestdruck 10 to :zur Ölabkühlung ? mit Elektroventilator Holsfxyh Hohccqmsnl :manuell, über Schmiernippel oder Kartuschen :SIEMENS / MOELLER :auf Schwenkarm :automatisch über 2 Handbetrieb mit Schlüsselschalter, manuell über Bedienpult im Einrichtbetrieb :Zweihandbedienung beweglich, :zur Datenübertragung :Siemens für Fernwartung :zur Hublängeneinstellung :0 ? 10 sec. Oil tank capacity:150 l :800 mm lang, vorne und hinten, 300 mm unten diagonal

Condition: as good as new (ex-display), Year of construction: 2016, pressure:160 t stroke:600 mm total power requirement:7,5 kW weight of the machine ca.:7 t draw back pressure:16 t :1 Stück Column-Diameter:160 mm dayligth:800 mm table surface area:1200 x 800 mm :400 mm Hnslsfxyi Iohccqmjl table height:850 mm table load:5 t pre-running speed:1 bis 9,8 mm/sec return speed:1 bis 9,8 mm/sec quantity of oil:220 l

Condition: as good as new (ex-display), Year of construction: 2017, machine/vehicle number: DF0052, pressure:200 t distance between columns:1200x1000 mm stroke:600 mm total power requirement:32,5 kW weight of the machine ca.:20,5 t dimensions of the machine ca.:4000x2600x5000 m draw back pressure:20 t Helefxyirohccqmsnl Master cylinder:1 Stück voltage:400 V frequency:50 Hz :24 V :BOSCH/REXROTH dayligth:800 mm :1200x1000 mit T-Nuten nach Kundenwunsch DIN 650-22 mm work height max.:1100 mm pre-running speed:170 mm/sec return speed:150 mm/sec Speed printing phase:15 mm/sek. Hydraulic block:REXROTH demand for oil:500 l pressure control:über PLC (Mindestdruck 20t) Oil Cooling:elektrisch :220 (im Schaltschrank) V memory:200 Programme :über Monitor von 20-200 t Controll:Zweihandbedienung beweglich :2-10 mm/sec :0-10 sec

Condition: as good as new (ex-display), Year of construction: 2015, machine/vehicle number: 4293, pressure:40 t Hjlhedxrqxeccqmenl table length:1000 mm table width:700 mm daylight opening:1200 mm No. of Cylinders:1 St. stroke length max.:1200 mm table height over floor:700 mm table extendable:1200 mm Speed of table:25 mm/sec Table tilting:45 Grad table load:5 t Fold-down upper tool:170 Grad :1250 x 1000 mm :95 mm/sec speed of return flow:80 mm/sec working speed:0 - 10 / 10 - 155 mm/sec dimensions:4300 x 2700 x 4500 mm total weight:8,5 t Monitor Siemens:9 Zoll :1200 mm

Condition: new, Year of construction: 2017, machine/vehicle number: DF0149, pressure:2x 75 / 150 t passage width:2050 x 965 mm stroke:800 mm total power requirement:Hauptmotor 22 kW weight of the machine ca.:6,5 t dimensions of the machine ca.:1500 x 1025 m :150 mm :150 mm :72 mm :2 kW :870 x 350 x 150 mm :1500 x 600 x 150 mm :1500 x 1025 x 75 mm :1500 x 1025 x 150 mm :120 mm :80 mm :350 l demand for oil:320 l Hjlhced Aftpecqmonl :350 mm max. open height:1600 mm :15-0 mm/sec :100 mm/sec :2050 x 965 mm :6 mm :0,5 mm

Condition: used, machine/vehicle number: DF0139, pressure:30 t passage width:1000x1000 mm stroke:800 mm total power requirement:3 kW weight of the machine ca.:5 t dimensions of the machine ca.:3360x1300x1360 mm return capacity:3 t column diameter:75 mm Hjlhccqofxykhomonl traversing speed:bis 200 mm/sec. :0-10 mm/s :200 mm/sec table height over floor:900 mm distance table - lower edge of ram:1000 mm :126 mm diameter of piston:71 mm

Year of construction: 2017, Condition: used, pressure:500 t passage width:1300x800 mm stroke:600 mm weight of the machine ca.:18 t dimensions of the machine ca.:2400 x 2400 x 5500 m draw back pressure:50 t Controll:Zweihandbedienung Holsd E Irmohccqmenl cylinder:1 Stück motor:50 kw Oil Cooling:elektrisch column diameter:200 mm work height max.:700 mm Table dimensions:1900 x 800 mm table height over floor:1000 mm pestle plate:1300 x 800 mm pre-running speed:150 mm/sec work speed:5-10 mm/sec. return speed:150 mm/sec :1500 l quantity of oil:1400 l

Condition: used, Year of construction: 2015, machine/vehicle number: A2536805, pressure:40 t stroke:250 mm return capacity:6,3 t motor:5,5 kw Max Working height:450 mm :90 mm/sec. :10 mm/sec. Holhccefxyhfsqmsnl spindle stroke:250 mm pestle plate:500 x 200 mm table plate:600 x 650 mit T-Nuten mm Table cut-out:200 x 170 mm table height:850 mm :200 l

Condition: used, machine/vehicle number: 4396, pressure:200 t distance between columns:1200x1000 mm Holhccefxyh Aeqmonl stroke:600 mm total power requirement:32,5 kW weight of the machine ca.:20,5 t draw back pressure:20 t :1 Stück voltage:400 V frequency:50 Hz :24 V :Rexroth/Bosch dayligth:800 mm working area:1200x1000 mm :1200x1000 mm work height max.:1100 mm :170 mm/sek. :150 mm/sek. :15 mm/sek. quantity of oil:500 l :220 V memory:200 Programme :20-200 über Monitor t :5-170 mm/sec. :0-10 sec :2-10 mm/sec :750x950 mm :300 mm :5-50 t :2-80 mm/sec :1000 kg

Condition: like new (used), Year of construction: 2016, passage width 2500 mm Hnolhein Et Nsccqmel stroke 900 mm Total power requirement 62 kW machine weight approx. 27,5 t dimensions L x W x H approx. 3950 x 2200 x 4850 mm retraction force 40 t Main cylinder 2 pieces column diameter 220 mm installation height 1300 mm table size 2500 x 1600 mm ram size 3100 x 16000 mm table height above floor approx. 900 mm forward speed 200 mm/sec return speed 200 mm/sec working speed 5 - 15 mm/sec oil tank 1500 l oil quantity 1200 l pressure control adjustable from up to 50 - 400 t thermoforming cushion 1400 x 800 mm thermoforming unit capacity 30 - 60 t deep drawing cushion stroke 250 mm thermoforming cushion speed 5 - 80 mm/sec robust machine body with solid welded construction low maintenance and reliable piston rod with induction hardening and chrome plating T-slots according to customer requirements, if not specified 22mm according to DIN CE certificate manufactured according to EU standards operating instructions, technical documentation, documentation in German language engineering steel LCG ASTM A36 T-slots in table and ram according to DIN 650-22 Travel control adjustable via monitor Light sensors front + rear: Sick 1300mm Hydraulic components Bosch Rexroth Monitor Siemens 12 inch Electrical control box for wall mounting Interior of the press illuminated with LEDs Hydraulic block monitored by safety PLC Energy control system: Reduction of the idle consumption of the pump to approx. 2 kw Remote control for remote maintenance Two-hand operation on movable stand Further information: Pressure build-up up to 400 T within max. 4 seconds after closing the die. Left side of the press closed by door 1000 x 800 mm with cross bars Ø 20 mm Right side of the press closed by door 1000 x 800 mm with cross bars Ø 20 mm Operation of the press can be manual, semi-automatic or fully automatic

Condition: like new (used), Year of construction: 2022, machine/vehicle number: DF0147, Pressure: 150 t Total power requirement: 20 kW Machine weight approx.: 11.5 t space requirement approx.: 8800 x 1800 x 2200 mm pressure setting infinitely variable via rotary control : 15-150 t cylinder diameter : 100 mm pressing speed (infinitely variable via joystick) : 0-9,9 mm/s servo motor : 2 kW cooling unit : 1 kW Oil tank (under press table): 350 l Oil cooling (electric): 1 kW (max) Profile straightening press 150 T with two pressure cylinders. The straightening machine is prepared for the particular type of material by interchangeable rounded spacer elements. The replacement of the 10 inserts is done manually by simply pushing them into the holding grooves. The scope of delivery includes basic equipment for one profile. The program for the respective profile is then called up on the monitor. The monitor shows the ideal line and, in addition, an ascending and descending millimeter scale with 0.5 mm lines. The profile to be straightened is now placed on the left side of the table, pushed against a holder and clamped with a quick-clamping device. Both the holder and the quick-clamping device are mounted on a clamping plate for quick adjustment. This clamping plate moves on a linear guide from left to right and vice versa. Transport is by a chain drive and a servo motor. The movement is triggered by a joystick on the control panel. Hnslefxygwjhccqmsl After the profile has been clamped, the operator moves the clamping platen into the press using the joystick. The travel speed is up to 100 mm per second, but can be continuously adjusted down to 10 mm per second. To do this, it is sufficient to pull the lever of the control system slightly less. A high-resolution camera now shows the profile in the press. The operator sees exactly the deviation from the ideal line. Depending on the need, he now pushes or pulls the profile to the desired accuracy. He then continues to move slowly through the press, seeing in detail on the monitor whether the profile is now straight. Depending on the need, he can now move the profile forwards or backwards and readjust it. After the profile has been straightened, it moves out of the press on the right and can be removed. If desired, the clamping platen now moves back to the loading position on the left or it is now loaded from the right to save time. The press may only be operated under the following conditions: Perm. ambient temperature: 5-60 °C Permissible relative humidity: at 20°C - 90%, at 40°C - 50% Height of the installation site NN: + 1000 m Perm. fluctuations E-mains: +/- 10%.

Condition: used, Year of construction: 2015, machine/vehicle number: 4273, pressure:110 t table length:1200 mm table width:1000 mm stroke max.:1150 mm dimensions:4200 x 2400 x 4800 mm draw back pressure:11 t stroke max.:1150 mm weight:16 t stroke of the table:1200 mm swivable table::45 Grad table load:12 t table speed:25 mm/sec table speed:10 mm/sec power capacity:23 kW voltage:400 V control voltage:24 V DC frequency:50 Hz work speed:0 - 10 mm/sec. :130 mm/sec :195 mm/sec. Colour:Grau 7035 RAL Colour:Orange 2009 RAL Colour:Dunkelgrau 7021 RAL Oil tank capacity:400 l Hnelhccqed Ap Ugsmsl Recommended oil:DIN HLP / ISO VG 46

Condition: as good as new (ex-display), Year of construction: 2022, machine/vehicle number: NEBR-4397, Here are the technical data of the offered machine: If the press does not exactly match your requirement profile, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! ##### Technical details Pressure 15 t Technology stroke 160 mm Machine weight approx. 330 kg oil tank 10 l robust machine body with solid welded construction, manufactured according to DIN 8651 ##### Additional information low-maintenance and reliable due to robust technology cylinder with induction hardening and chrome plating steel quality: engineering steel LCG ASTM A36 4 support feet with M30 holes for floor mounting ##### Equipment 1.5 T rotating mandrel attachment, mechanical, with locking, toothed shaft and brake and 220 mm travel hydraulic hand pump with max. 15T pressure and 160 mm travel, with return spring back wall projection to the center of the tool holder 280 mm mounting table swivels 180 degrees to the right with 60 mm bore in the center, M 12 T-slots Clearance height between swivel table and slide/turning mandrel guide 450 mm Passage height up to additional table, insertable, 650 and 800 mm Additional table with center hole, 60 mm, insertable, T-slots M12, size 270x200 mm Height of the base with two inserts for additional table 750 mm on the cylinder a pressure plate, hardened, diameter 10 mm bigger than cylinder in the cylinder head tool holder M 30 Pump lever moves from top to bottom Oil tank for 10 L hydraulic oil AW 46 Painting of the machine body: Blue, RAL 5012, pressure paint Painting of the attachments: Anthracite, RAL 7021 hydraulic single-column combination press as a special machine 15 tons, manual (C-press, hydraulic press, hydraulic press) ##### Are you looking for a custom-fit machine? Hnolhcefhcc Iecqmsl Contact us for an individual offer. Our hydraulic presses are manufactured according to German machinery directives, as well as European machinery directives (Directive 2006/42/EC), EC standards and EU safety regulations. Furthermore our presses exceed the Canadian and European safety requirements, because they correspond in all points to the national Brazilian safety guideline NR 12, which is based on these. Our great strength is the special machine construction and the press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Year of construction: 2020, Condition: reconditioned (used), machine/vehicle number: DF0317, pressure:400 t passage width:600 mm stroke:400 mm Weight of machine approx.:14 t dimensions:2380 x 1680 x 3580 mm Engine Output:36 kW Max Working height:750 mm Approaching Speed max. :10 mm/sec Pressure Speed:10 mm/sec column diameter:230 mm Return Capacity:40 t speed rapid traverse:25 mm/sec Travel:500 mm Oil Tank Capacity:600 l Oil Cooling:1,5 kW :6 m Monitor:WEG 12 Zoll :6800 ? Hslhod E Irheccqmsnl :4200 ? Speed increase to 80 mm/sec.:19000 ? every additional meter conveyor belt:850 ? Faster Version with approach and working speed at 60mm/sec ist available on request. Price (excl. options): 117.500,--

Year of construction: 2020, Condition: like new (used), pressure:150 t stroke:500 mm Weight of machine approx.:ca. 8,5 t dimensions:1200x1800x3100 mm Engine Output:10 kW Max Working height:1000 mm Approaching Speed max. :9,9 mm/sec Pressure Speed:100t = 9,9 bis 0 mm/sec Table height above ground level (approx.):1000 mm :Schmiernippel column diameter:230 verchromt mm Return Speed:25 mm/sec :500 l demand for oil:ca 400 l Maintenance Balcony:5800 ? :3900 ? :2800 ? :4800 ? :29000 ? :8200 ? Faster Version with approach and working speed at 60mm/sec ist available on request. Price (excl. options): 117.500,-- Hjlhsdxvfijccqmenl

Condition: like new (used), Year of construction: 2015, operating hours: 350 h, Technical details Pressure 110 t Technology passage width 1200 x 1000 mm stroke 1200 mm Machine weight approx. 12 t space requirement approx. 4500 x 4300 x 2700 mm Main cylinder 1 piece Installation height ( distance table to ram plate ) 1200 mm table height 700 mm table extendable by 1200 mm table tiltable by 45 degrees upper tool tiltable by 180 degrees Table rotatable by 180 degrees table load max. 10 t travel speed of the table 25 mm/sec forward speed 195 mm/sec return speed 130 mm/sec Working speed adjustable from 0 to 10 mm/sec. Table area between columns 1250 x 1000 mm Motors WEG Accessories Painting structure RAL 7035 (light gray) Additional information Painting cladding, doors, maintenance balcony RAL 1021 (Yellow) Painting accessories RAL 7021 (dark gray) Columns and cylinders are made of tool steel SAE 1045 (identical with German standard C45) columns and cylinders are outside induction hardened and chrome-plated robust machine body with solid welded construction thanks to high quality components of German manufacturers low maintenance and reliable maintenance balcony with marine ladder entire range of motion secured by SICK light barriers secured table moves forward out of the machine and straightens up upright by 45 degrees on request. Control cabinet to the left of the machine Monitor control with 200 memory locations REMOTE function for remote maintenance German documentation CE certificate Control SIEMENS Equipment Screen 9" SIEMENS Hydraulics from REXROTH/PARKER Light sensors SICK Pressure, speed, travel adjustable via monitor control ram plate can be folded down hydraulically, moves up to approx. 180 degrees Interior lighting Cylinder with induction hardening and chrome cladding Hneleh A Icmohccqmsl Operator panel on swivel arm Two-hand operation on movable stand USB interface for data transfer It is suitable also for the production of small series, which it moves with up to 200 mm/second. The table moves completely outwards, where it straightens up to 70 degrees if desired. The ram plate folds outward by up to 170 degrees. The machine weighs 16 T and can move molds weighing up to 8 T.

Condition: new, Year of construction: 2019, pressure:275 t distance between columns:3000 mm total power requirement:30 kW weight of the machine ca.:40 t draw back pressure:27 t pump capacity:Axialpumpe mit Proportionalventil :6000 mm :max. 3000 mm Table dimensions:6000 x 3000 mm table height over floor:700 mm distance between table / ram:1100 mm :450 l traversing speed:auf X und Y, 30-33 mm/sec. down speed:2-10 mm/sec :2-50 mm/sec. Hjlofxyigjhccqmenl Cylinder hub:900 mm Cylinder diameter:440 mm Stestle extension:200 / 200 mm / Ø :40 mm Siemens Control System:S7 1200 Monitor Siemens 9":Touch Panel Tax desk:tragbar

Condition: new, pressure:400 t distance between columns:3400 mm stroke:500 mm total power requirement:55 kW weight of the machine ca.:49 t draw back pressure:26 t pump capacity:131 Lt./min dimensions:7.900 x 5.500 x 4.300 mm :5000 mm :2800 mm table height over floor:700 mm distance between table / ram:1000 mm :700 l traversing speed:0-33 mm/sec. down speed:0-10 mm/sec :0-25 mm/sec. Helhccofhcc Rsqmenl

Condition: as good as new (ex-display), Year of construction: 2016, We offer an immediately available Hydraulic spotting press with 40 tons pressure. Due to a change of warehouse location, this press is offered at a very competitive price. Pressure 40 t Table length 1000 mm table width 700 mm Machine weight approx. 9 t space requirement approx. 4000 x 4400 x 1800 mm stroke length 1050 mm installation height 1200 mm table rotatable 180 degrees table load max. 5 t forward speed 100 mm/sec return speed 100 mm/sec Hslhcehtm E Nscqmjnl working speed adjustable from 0 to 10 mm/sec. Main cylinder 1 piece table extendable for 1050 mm table tiltable 50 degrees upper tool tiltable 180 degrees Traversing speed of the table 25 mm/sec Pressure, travel and speed adjustable via monitor- control adjustable robust machine body with solid welded construction, manufactured according to DIN 8651 low maintenance and reliable due to robust technology maintenance balcony with marine ladder entire range of motion secured by Sick light barriers Table moves out of the machine to the front and straightens up by 45 degrees on request. Control cabinet to the left of the machine Monitor control with 200 memory locations REMOTE function for remote maintenance Operating manual, technical documents, documentation in German language CE certificate monitor SIEMENS 9" Motors from WEG Hydraulics from Bosch Rexroth Interior lighting Operator panel on swivel arm Two-hand operation on movable stand USB interface for data transfer Siemens control system Light sensors Sick 1250 mm ram plate can be folded down hydraulically, moves up to approx. 175 degrees Columns and cylinders are made of SAE 1045 tool steel (identical to German standard C 45) and are induction hardened and chrome plated on the outside. The linear measuring rod informs the control system of the position of the ram in each case. The travel distance, the upper stop point and the changeover point at which the press is to switch from idle to working speed, as well as the end position to be approached, can be entered easily and quickly via the monitor control. The working speed can be set in 1 mm/sec increments from 0 to 10 sec and in 10 mm increments from 10 to 155 mm. The control monitors the secured areas, all hydraulics and the pump. The control system is housed in a separate control cabinet. The actual press operation is carried out via a control panel mounted on a swivel arm, which reduces the distances involved.