TOOL CHANGE MOTOR

HOMAG

Condition: ready for operation (used), Year of construction: 2008, machine/vehicle number: 0-250-23-0021, functionality: fully functional, workpiece length (max.): 2,500 mm, workpiece width (max.): 1,000 mm, workpiece height (max.): 80 mm, feed rate X-axis: 138 m/min, feed rate Y-axis: 80 m/min, Submission of a bid obligates timely collection by 15.06.2026! TECHNICAL DETAILS X-axis speed: 138 m/min Y-axis speed: 80 m/min Z-axis speed: 50 m/min Workpiece length: 300–2,500 mm Workpiece width: 100–1,000 mm Workpiece height: 4–80 mm MACHINE DETAILS Control system: power control PC 85 T Dimensions (L x W x H): 6,500 × 2,300 × 2,700 mm Electrics: 3 × 415 V / 50 Hz Power consumption: 19.5 kW Fuse: 50 A Pneumatics: min. 7 bar Air consumption: 2,500 NL/min Extraction connection: 2 × 280 mm Gjdpfx Aey Sad Holmsbl Extraction capacity: min. 4,450 m³/h

Condition: used, Year of construction: 2007, power: 43 kW (58.46 HP), cutting height (max.): 90 mm, cutting width (max.): 1,200 mm, cutting length (max.): 5,600 mm, feed rate X-axis: 40 m/min, The machine comes from a business liquidation. Inspection under power is possible! TECHNICAL DETAILS Maximum panel width: 1,200 mm Maximum panel length: 5,600 mm Minimum panel width: 150 mm Minimum panel length: 250 mm Minimum panel height: 8 mm Maximum panel height: 90 mm Maximum feed speed: 40 m/min The machine is configured as follows: Number of processing units: 4 Unit 1: Double cutter, top and bottom Motor power: 11 kW Speed: 7,090 rpm Unit 2: Scoring unit Gedpfx Asy R S I Uolmebl Motor power: 2.2 kW Speed: 6,920 rpm Unit 3: Milling unit Motor power: 8 kW Speed: 7,090 rpm Unit 4: Milling unit Design type: on rear table Motor power: 2.2 kW Speed: 6,920 rpm MACHINE DETAILS Control system: WINDOWS Machine programming software: POWER CONTROL PC22 Total connected load: 43 kW EQUIPMENT Top pressure unit Additional guide for workpieces Rubber conveyor belt NC positioning system The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. External reference: 8448

Condition: used, Year of construction: 2007, travel distance X-axis: 6,000 mm, travel distance Y-axis: 3,000 mm, number of slots in tool magazine: 10, controller model: POWER CONTROL PC85, spindle speed (max.): 24,000 rpm, The machine originates from a business closure. Inspections under power are possible! TECHNICAL DETAILS Travel range X-axis: 6,000 mm Travel range Y-axis: 3,000 mm Working area X-axis: 5,600 mm Working area Y-axis: 1,200 mm Rapid traverse X-axis: 80 m/min Rapid traverse Y-axis: 80 m/min Rapid traverse Z-axis: 30 m/min Milling spindles: 2 Main electrospindle power: 11 kW Spindle speed: 24,000 rpm Total number of tool changer positions: 10 MACHINE DETAILS Type of operation: Milling Control system: POWER CONTROL PC85 Machine programming software: WOODWOP 5.0 Number of controlled axes: 4 Vacuum cups: 32 Individual vacuum pump capacity: 120 + 80 m³/h Number of pumps: 2 Total installed power: 27 kW EQUIPMENT Vacuum loading Motorized transfer system Automatic panel loading system Automatic panel stacking system Gedoy R Swiepfx Almsbl Liquid cooling system CE marking Protective structure for operating units with safety sensors Protective netting on the machine Chip conveyor for waste removal The machine is being sold and delivered in its actual and legal condition ("as seen and approved") based on the photographic documentation and technical/commercial documents of descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 8457

Condition: used, Year of construction: 2002, travel distance X-axis: 10,500 mm, travel distance Y-axis: 2,700 mm, number of slots in tool magazine: 24, controller model: POWER CONTROL PC83, milling spindle speed (max.): 18,000 rpm, The machine comes from a business closure. Inspection under power is possible! TECHNICAL DETAILS Travel path X-axis: 10,500 mm Travel path Y-axis: 2,700 mm Working area X-axis: 5,600 mm Working area Y-axis: 1,200 mm Speed X-axis: 80 m/min Speed Y-axis: 80 m/min Speed Z-axis: 30 m/min Main electrospindle power: 12 kW Number of milling spindles: 2 Spindle motor output: 12 kW Spindle speed: 18,000 rpm Number of controlled axes: 4 Number of tools in the changer: 24 Number of tool magazine positions: 12 (2 magazines) Maximum panel thickness: 40 mm Minimum panel thickness: 10 mm MACHINE DETAILS Type of machining: Edge processing, Milling Control system: POWER CONTROL PC83 Programming software: WOODWOP 5.0 Total installed power: 51 kW Number of work zones: 1 Number of rails: 5 Number of vacuum cups: 10 Number of vacuum pumps: 2 Capacity per pump: 120 m³/h EQUIPMENT Worktable: Pod and rail Positioning via NC Automatic panel loading system: vacuum loading system Gsdpfey R Si Sox Almsbl Automatic panel stacking system Vacuum pump Liquid cooling system Gluing unit with hot melt pre-melter Edgeband magazine Tool magazine at rear of machine Protective structure for operating units with safety sensors Protective net attached to the machine Safety system: front safety mats Waste chip conveyor The machine is sold and delivered in its current technical and legal condition ("as seen and approved"), based on photographic documentation and technical/commercial documents of descriptive character. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operating the machine at the destination. External reference: 8458

Condition: used, Year of construction: 2007, workpiece height (max.): 60 mm, edge thickness (max.): 35 mm, feed rate X-axis: 40 m/min, controller model: POWER CONTROL PC22", The machine comes from a company closure. Inspections under power are possible! TECHNICAL DETAILS Number of working units: 11 Maximum feed speed: 40 m/min Maximum panel thickness: 60 mm Minimum panel height: 16 mm Minimum panel width: 85 mm Minimum edge thickness: 0.3 mm Maximum edge thickness: 35 mm Pressure system: Rubber belt Workpiece support guides NC-controlled positioning Panel infeed alignment system The machine is configured as follows: PRE-MILLING / MILLING UNITS Number of pre-milling / milling units: 2 Unit 1: Pre-milling unit Motor power: 4.5 kW Speed: 5,860 rpm Automatic, time-controlled engagement Unit 2: End trimming unit Motor power: 1.8 kW Automatic tool change GLUING AND EDGE FEEDING Number of edge rollers: 68 Number of pressure rollers: 14 (1 x 7 + 1 x 7) Lamps for pre-heating the panel edge Pre-melter for PUR adhesive Gedpfx Alsy R R T Nomsbl Gluing system Adhesive pot for PUR glue NC-controlled positioning EDGE PROCESSING UNITS Number of edge processing units: 8 Unit 1: End trimming unit Number of motors: 2 Motor power: 0.22 kW Speed: 10,350 rpm NC-controlled positioning Unit 2: Top and bottom flush trimming unit Number of motors: 2 Motor power: 0.55 kW Speed: 11,400 rpm Unit 3: Corner rounding unit Number of motors: 2 Motor power: 0.4 kW Speed: 10,980 rpm Automatic tool change NC-controlled positioning Automatic, time-controlled engagement Unit 4: Scraper unit NC-controlled positioning Unit 5: Glue joint scraper unit Unit 6: Buffing unit Number of motors: 4 Motor power: 0.25 kW Speed: 1,390 rpm Automatic, time-controlled engagement Unit 7: Buffing unit Number of motors: 1 Motor power: 0.30 kW Speed: 3,000 rpm Unit 8: Buffing unit Number of motors: 2 Motor power: 0.18 kW Speed: 1,370 rpm MACHINE DETAILS Control system: WINDOWS XP Machine programming software: POWER CONTROL PC22 The machine is sold and delivered in its actual and legal condition (“as seen and agreed”) based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and is responsible for the installation, securing, and use of the machine at the destination. External reference: 8453

Condition: good (used), Year of construction: 2007, 1. Loading BARGSTEDT O TSH200 / D / 30/12 2. The first HOMAG OPTIMAT KFL 525 / M1 / ​​C machine 3. HOMAG OPTIMAT TDL 510 / C turntable Gedpfx Ajik H Egelmobl 4. Drug machine machine HOMAG OPTIMAT KFL 526 / M2 / C 5. HOMAG OPTIMAT TDL 510 / C turntable 6. WANDRES THE BRUSH 7. Unloading BARGSTEDT O TSH200 / D / 30/12 The machine is in constant use Machine immediately

Condition: good (used), Year of construction: 2003, machine/vehicle number: 0-201-22-4227, functionality: limited functionality, workpiece length (max.): 4,800 mm, workpiece height (max.): 80 mm, number of slots in tool magazine: 18, spindle motor power: 7,500 W, number of spindles: 2, rapid traverse Z-axis: 30 m/min, rapid traverse X-axis: 80 m/min, rapid traverse Y-axis: 80 m/min, spindle speed (max.): 18,000 rpm, spindle speed (min.): 18,000 rpm, Equipment: rotational speed infinitely variable, Main spindle equipped with C axis and extension for Flex 5 aggregate. Working area X: 4800 mm. Working area Y: 1300 mm. Working area Z: 80 mm. 8 consoles. 1 vacuum pump. 18-position travelling tool changer. Tool holder HSK 63. Adapter - horizontal boring head with 4 fixed spindles. Boring head with 17 spindles. Additional spindle with collet chuck. Measuring probe. Central automatic oil lubrication. Lifting rails for console table. Godpfx Alsxdxa Ismjbl

Condition: like new (used), Year of construction: 2022, functionality: fully functional, HOMAG EDGETEQ S-500 (OPTIMAT KAL 375/16/V25) Year of manufacture: 2022 Serial number: Excellent condition – used only for demonstration and sample production. Machine has been professionally maintained and is immediately available for inspection in Slovenia. Technical data and equipment: Continuously adjustable feed speed: 16–25 m/min Workpiece thickness: 8–60 mm Fixed fence on the left-hand side Working height adjustable Pre-installation for LOOPTEQ O-200/O-300 return system Feed lock system Workpiece alignment at infeed with roller support Top pressure unit Gsdsxwuryjpfx Almjbl Sizing package with DIA joint trimming cutter set WD40 Gluing package with preheating up to 60 mm thickness Adhesive application system with emptying function Edge magazine with two vertical roll holders Pressure zone PERFORMANCE2 package End trimming unit PK25 Rough trimming unit BF10 (I-HM straight cutter set) Profile trimming unit FF32 top/bottom WD60 with FLEXTRIM quick-change system (2 radii) Multi-scraper MN21 automatic with profile knife set Cleaning agent spraying unit Glue joint scraper FA20 BASIC Buffing unit FP10 top and bottom PowerControl PC23 PowerTouch control system TAPIO Ready Ethernet network connection Wired manual control for setup operation Software package WOODCOMMANDER with MMR data logging, ToolManager, speed adjustment for track control, and full diagnostic functions Documentation in Slovenian (digital and paper format) Remote service enabled

Condition: used, Year of construction: 2005, machine/vehicle number: 0-201-10-2035, functionality: fully functional, operating hours: 31,690 h, table load: 500 kg, Main technical data: Model: BOF 611 / 34 / 13 / 2R — CNC machining center with 3 working axes Gedow Ilvfepfx Almebl Spindle power: 15 kW, HSK 63 system Working dimensions: X axis: 3,740 mm (single table mode) / 1,830 mm (pendulum operation) Y axis: 1,550 mm Z axis: 300 mm Material feeding options: - Gantry feeder (HOMAG OPTIMAT) - Double work table — allows alternate or parallel operation Additional features: Tool changer: 12 positions Control and software: Flex5 interface and WoodWOP (e.g., version 6.0) for CNC programming Weight and construction: Weight: approx. 25,000 lb (~11,340 kg) Dual matrix table system (each 5 × 6 ft) Summary: The HOMAG Optimat BOF 611 is an advanced CNC machining center for woodworking, equipped with a powerful 15 kW HSK 63 spindle and three controlled axes. Ideal for precise milling, drilling, and large-format workpiece machining, with automated feeder (not included) and a dual table system for increased productivity. Buyer requirements: - Dismantle and prepare the machine for transport - Load the machine onto a truck - Arrange transportation from the seller’s location to the buyer’s location - Organize transport insurance if required The machine can be viewed under power/in current (working) conditions. It is still in daily use. For visits or a video call, please contact us.

Condition: excellent (used), Year of construction: 2011, 5-axis working center in very good condition. Technical data will be updated soon. Gbodpfjx Ur Iiex Almol