2-axle chassis

HOMAG

Condition: refurbished (used), Year of construction: 2007, machine/vehicle number: 0-200-03-9040, functionality: fully functional, edge thickness (max.): 20 mm, feed rate X-axis: 18 m/min, year of last overhaul: 2025, The machine underwent a complete overhaul on November 10, 2025, and was fitted with two new adhesive tanks. The machine has been serviced annually; in 2023, the software and computer system were completely replaced. The machine is equipped with the following units: Gluing/pre-coating unit Pressing zone Cutting unit (HL) Milling unit (MFL) Profiling unit (PN) Polishing unit (SM) Gluing system FE-MA-TECH Advanced PUR 2 kg TECHNICAL DETAILS Feed speed: 18 m/min Panel thickness: 10 - 60 mm Edge thickness: 0.3 - 20 mm MACHINE DETAILS Guodpfx Ahezap H Sovsc Gluing system: FE-MA-TECH Advanced PUR 2 kg

Condition: excellent (used), Year of construction: 2018, Specification Length: 4605mm Workpiece Thickness: 40mm Edge Material Roll: 0.4 – 3mm Edge Material Strip: 0.4-3mm Feed Speed 8m/min Joint Trimming Unit 40mm Quick Change Application Unit Gusdpfxezdklcj Ahvoc Magazine for Coiled Material Pneumatic 2 point adjustment Pressure Zone End Trim Unit with Pneumatic Adjustment Pneumatic Adjustment Fine Trim Contour Trimming Unit Pneumatic Adjustment Profile Scraping Unit Glue Joint Scraper Buffers LED Indoor Lighting EasyTouch Control System Manual Central Lubrication Manual Top Pressure Adjustment Roller Top Pressure

Condition: excellent (used), Year of construction: 2018, Specification: Vertical Drill Block with 13 Spindles Horizontal drill block with 4 spindles in the X Horizontal drill block with 2 spindles in the Y Guedjzdki Uepfx Ahvoc Grooving Saw D=100mm Plausibility check 10kw tool change spindle 4 position tool changer Workpiece length max 200-3050mm Workpiece width 70-850mm Workpiece thickness 8-56mm Powertouch screen Woodwop for machine Energy Saving Mode

Condition: ready for operation (used), Year of construction: 2018, cutting length (max.): 4,300 mm, Panel saw manufactured in 2018. This HOMAG PROFI HPP 300 / 43 / 43 features a cutting length of 4,300 mm and a cutting width of approximately 4,250 mm. It has a maximum saw carriage feed speed of 130 m/min and a maximum saw blade diameter of 350 mm. If you are looking to get high-quality panel cutting capabilities, consider the HOMAG PROFI HPP 300 / 43 / 43 machine we have for sale. Contact us for further details. • Cutting width (programmable pusher): approx. 4,250 mm • Max. saw carriage feed speed: 130 m/min (optional up to 150 m/min) • Saw blade projection: 80 mm (optional 95 mm) • Max. saw blade diameter: 350 mm • Main saw blade diameter: 350–380 mm (depending on configuration) • Main saw motor: 11 kW • Scoring saw motor: adjustable, 1.5–2.2 kW • Clamps: 7 units (2-finger design) • Control system: CADMATIC 4.1 / 4.5 or powerTouch (depending on configuration) Gsdozdignopfx Ahvouc • Total connected load: approx. 18.4 kW • Compressed air: 6 bar • CE marking: Yes • Stack height: up to approx. 80 mm (standard) • Extraction capacity requirement: approx. 3,350–5,230 m³/h • Processing: Single panels and stack cuts

Condition: ready for operation (used), Year of construction: 2017, overall weight: 3,800 kg, Edgebander manufactured in 2017. This HOMAG Optimat KDF 440 C features a workpiece thickness capacity of 8 - 60 mm and edge material compatibility of 0.4 - 8 mm. It offers a variable feed speed of 8 - 18 m/min and includes several units for joint trimming, glue application, and corner rounding. If you are looking to get high-quality edge banding capabilities, consider the HOMAG Optimat KDF 440 C machine we have for sale. Contact us for further details. • Condition: Used • Workpiece thickness: 8–60 mm • Edge material: 0.4–8 mm (depending on unit configuration) • Feed speed: 8–18 m/min (variable) • Min. workpiece length: approx. 120 mm • Min. workpiece width: approx. 60 mm • Glue application: EVA hot-melt adhesive; PUR-compatible (optional) • Glue pot: Teflon-coated; quick-change capability • Total connected load: approx. 15–20 kW (depending on configuration) • Compressed air requirement: 6–7 bar • Control system: powerControl / powerTouch • CE marking: Yes • Unit configuration: • Joint trimming unit • Glue application unit • Pressure zone Gusdezdidaopfx Ahvec • End trimming unit • Top/bottom trimming unit • Corner rounding unit • Scraper unit • Buffing unit

Condition: good (used), Year of construction: 2015, machine/vehicle number: 0-200-24-0779, functionality: fully functional, input voltage: 400 V, input current: 55 A, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, total length: 10,825 mm, Used single-sided HOMAG edge-banding machine for straight edges – KAL 370 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2015 EQUIPMENT / SPECIFICATION BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, Guedpfjy A I Sgox Ahvoc - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clockwise, counterclockwise), 2x4kW, rear motor w. jumping function GLUING SECTION V20, consisting of: - QA60 glue application unit, with PTFE-coating (Teflon), with manual quick-adjustment glue gates - pneumatic clamping of glue application in mount - Pre-melter for EVA glue - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - modes: edge rolls, (veneer) strips, solid wood edging - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 4 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK85 horizontal, 2 motors, with straight/chamfer cutting function - Rough trimming 2x1.15 kW, top/bottom - Corner rounding FK11, 2 motors (top/bottom) with various trimming heads, motorised adjustment - Universal trimming unit, (e.g. grooving), 3.5 kW, tiltable, w. electro-pneumatic jumping control - Multi-Profile (radius-) scraping MN11 with automatic positioning by NC-axis (CAN) - Flat scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers) - Buffing unit FP10, top/bottom Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, power: 8 kW (10.88 HP), input voltage: 400 V, input frequency: 50 Hz, Equipment: documentation/manual, OPTIMAT BHX055 Guedpfx Asyvh Dpshvjc

Condition: ready for operation (used), Year of construction: 2018, number of axes: 3, total height: 1,895 mm, total width: 1,980 mm, overall weight: 1,580 kg, spindle motor power: 5,000 W, product length (max.): 2,950 mm, spindle speed (max.): 24,000 rpm, This 3-axis HOMAG WEEKE OPTIMAT BHX 055 was manufactured in 2018. It features a workpiece length capacity of 200 - 3,050 mm and a workpiece width of 70 - 850 mm. The machine includes 13 vertical drilling spindles and 4 horizontal drilling spindles, providing versatile machining capabilities. If you are looking to get high-quality CNC processing capabilities, consider the HOMAG WEEKE OPTIMAT BHX 055 machine we have for sale. Contact us for further details. Used Vertical CNC Machining CenterBrand: HomagType: Optimat BHX055Year of manufacture: 2018Technical data • Vertical CNC drilling and machining center • Workpiece length 200 - 3,050 mm • Workpiece width 70 - 850 mm • Workpiece thickness 12 - 60 mm • Milling spindle 1 unit • Main spindle power 5 kW • Max. speed 18,000-24,000 rpm (depending on configuration) • Tool holder HSK-F63 or ETP25 • Tool changer 4-position magazine • Vertical drilling spindles 13 • Horizontal drilling spindles (X) 4 • Horizontal drilling spindles (Y) 2 • Grooving saw X-direction • Control system Homag powerTouch / Power Control PC 86 • Software WOODWOP 7.x • Total connected load 11.5 kW • Compressed air requirement 7 bar • Machine weight approx. 1,580 kg Gujdpfxszc R Hfj Ahvoc • Footprint (L × W × H) approx. 2,950 × 1,984 × 1,895 mm • CE markingNote:The technical data and descriptions are copies of the original order confirmation. This information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2025, functionality: unexamined, Homag Centateq P110 PROFI BMG110/3115/F/K CNC machining centre (2025) with  Guodpfxozc Rzpo Ahvjc Almig Combi XP15 receiver mounted air compressor (2025) Air Plants Dust Extraction Ltd dust extraction system (2025)

Condition: used, machine/vehicle number: 008585, Type of edging: Thin edge, Thick edge, Solid wood, Veneer Gluing System: EVA Hotmelt, PUR Premilling Unit: yes Corner Rounding Unit: yes Grooving Unit: yes Max feed speed: 25 m/min Maximum panel thickness: 60 mm Operating Units: 8 nr Gedpfx Aey In A Aohvouc