VME interface HC010 REV 0.LWL

HOMAG

Condition: used, Year of construction: 2013, HOMAG edge banding line with infeed and outfeed. The machine consists of the following components: Machine configuration: HOMAG edge banding line with infeed and outfeed Infeed table: HOMAG PROFI TBL100/20/25/F FlexLine Edge banding machine: HOMAG PROFI KAL330/7/A3/WZ Panel outfeed: HOMAG ZHR 30/L/125/F TECHNICAL DETAILS Panel length min.: 240 mm Panel length max.: 3,000 mm Panel width min.: 120 mm Panel width max.: 1,200 mm Panel thickness min.: 12 mm Panel thickness max.: 60 mm Edge thickness min.: 0.3 mm Edge thickness max.: 3 mm Gluing system: EVA hot melt Number of processing units: 9 pcs. Number of units in the joining section: 1 pc. Number of units in the edge processing section: 7 pcs. Feed speed max.: 25 m/min Trimming unit Manufacturer / Model: S2 Gksdpfxsz En Axe Afuec Motor power: 3 kW Speed: 9,000 rpm Automatic cycle adjustment: Yes End trimming unit Manufacturer / Model: HL 84 Number of motors: 2 pcs. Motor power: 0.4 kW Speed: 12,000 rpm Working speed max.: 25 m/min Flush trimming unit, top and bottom Manufacturer / Model: BF10 Number of motors: 2 pcs. Motor power: 0.55 kW Speed: 12,000 rpm Corner rounding unit Manufacturer / Model: FK 11 Number of motors: 2 pcs. Working speed max.: 25 m/min Profiling unit Number of motors: 1 pc. CNC positioning: Yes Automatic cycle adjustment: Yes Edge pulling unit Manufacturer / Model: PN20 Glue application unit Manufacturer / Model: FA 11 Scraping unit Manufacturer / Model: FA 11 Number of motors: 2 pcs. Feed speed, infeed max.: 40 m/min Feed speed, outfeed max.: 25 m/min EQUIPMENT FlexLine infeed table Pressure bar with rubber belt Panel stop Overpressure Edge heating lamps Edge magazine with 24 positions Hot melt glue tank Hot melt pre-melter Edge pressing roller unit with 3 pressure rollers CNC positioning of the pressure rollers Spraying device PowerTouch PC23 machine programming software Panel outfeed via transfer roller conveyor Panel transport via motorized conveyor belt Clamping feed system Panel outfeed system, left CE conformity The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing and use of the machine at the destination. External Reference: 7694

Condition: used, Year of construction: 2008, workpiece height (max.): 40 mm, controller model: PowerControl P85, working width: 1,550 mm, working length: 4,175 mm, TECHNICAL DETAILS Working area, X-axis: 4,175 mm Working area, Y-axis: 1,550 mm Maximum workpiece thickness: 40 mm Number of working areas: 2 Traverse speed, X-axis: 80 m/min Traverse speed, Y-axis: 80 m/min Traverse speed, Z-axis: 30 m/min Table system: Beam table with vacuum cups Number of vacuum cup beams: 8 Positioning: CNC-controlled Drilling unit Position: Top Vertical drilling spindles: 20 Horizontal drilling spindles in X-direction: 10 Milling unit Position: Top Controlled axes: 4 + Flex5 Motor power: 15 kW Cooling: Liquid cooling Tool changer: Automatic Sawing unit Position: Top Gksdpfxoz Ekfvs Afusc Tool magazine: 2 slots Tool magazine 1: 18 slots Position of tool magazine 1: Rear of the machine Tool magazine 2: 10 slots Position of tool magazine 2: On the machining head MACHINE DETAILS Control system: PowerControl P85 Machine programming software: WoodWOP 5.0 EQUIPMENT Beam table with vacuum cups 8 vacuum cup beams Vacuum pump Automatic tool changer Liquid cooling PowerControl P85 control system WoodWOP 5.0 machine programming software Note: Tools not included The machine will be sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7350

Condition: used, Year of construction: 2005, feed rate X-axis: 60 m/min, plate length: 2,500 mm, plate width: 1,200 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Maximum plate width: 1,200 mm Maximum plate length: 2,500 mm Minimum plate width: 220 mm Minimum plate length: 250 mm Maximum feed rate: 60 m/min EQUIPMENT 90° transfer conveyor CE safety compliance Gjdpfsz Ekfcex Afuskc The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents, which are for descriptive purposes only. The buyer has the right to inspect the goods before collection and is responsible for the installation, securing, and use of the machine at the destination. External reference: 5981

Condition: used, Year of construction: 2010, controller model: PC85, working width: 1,750 mm, milling spindle speed (max.): 24,000 rpm, working length: 6,000 mm, TECHNICAL DETAILS Machining method: Drilling and milling Number of work areas: 2 Work area X-axis: 6,000 mm Work area Y-axis: 1,750 mm Number of controlled axes: 5 Travel speed X-axis: 80 m/min Travel speed Y-axis: 80 m/min Travel speed Z-axis: 30 m/min Gksdsz Ekb Depfx Afusc Table system: Console work table with vacuum cups Number of vacuum consoles: 10 CNC positioning: Yes Vacuum cups for workpiece clamping: Yes Number of vacuum cups: 40 Drilling unit Number of drilling units: 1 Position of drilling unit: Top Vertical drilling spindles: 20 Horizontal drilling spindles, X-direction: 5 Horizontal drilling spindles, Y-direction: 5 Total drilling spindles: 30 Milling unit Number of milling units: 1 Position of milling unit: Top Controlled axes: 5 Motor power: 12 kW Speed: 24,000 rpm Liquid cooling: Yes Automatic tool changer: Yes Number of tool magazines: 1 Tool positions: 72 MACHINE DETAILS Control: PC85 Programming software: WoodWOP 5.0 Vacuum pumps: 2 Individual output per vacuum pump: 250 m³/h Total connected power: 49 kW EQUIPMENT Console work table with vacuum cups 10 vacuum consoles with CNC positioning 40 vacuum cups for workpiece clamping 2 vacuum pumps Top drilling unit with 30 drilling spindles Top 5-axis milling unit with 12 kW electric motor spindle Liquid cooling Automatic tool changer Tool magazine with 72 tool positions PC85 control WoodWOP 5.0 programming software Automatic chip extraction Safety mats on the front of the machine Safety sensors Fixed safety guards CE conformity The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8167

Condition: used, Year of construction: 2007, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, controller model: PC22, TECHNICAL DETAILS The machine has the following configuration: Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed rate: 25 m/min Gkodpfx Aez Ekbkjfuoc Pressure bar: with rubber belt Panel stop: with CNC positioning Panel infeed alignment system: available Edge application unit Processing interval: automatically time-controlled Motor power: 3 kW Speed: 9,000 rpm Edge processing Edge heating lamps: available Roller magazine: available Hot melt adhesive reservoir: available Hot melt adhesive pre-melter: available Number of pressure rollers: 7 Positioning: CNC-controlled Trimming unit Number of motors: 2 Motor power: 0.8 kW Speed: 12,000 rpm Flush trimming unit, top and bottom Number of motors: 2 Motor power: 1.5 kW Speed: 12,000 rpm Edge rounding unit Manufacturer/Model: FF12 Number of motors: 4 Motor power: 0.4 kW Speed: 12,000 rpm Profile trimming unit Number of motors: 1 Processing interval: automatically time-controlled Motor power: 5 kW Speed: 11,600 rpm Scraping blade unit Manufacturer/Model: PN10 Glue scraping blade unit Brushing unit Number of motors: 2 Spray device: available MACHINE DETAILS Number of processing units in edge processing: 7 Control system: PC22 EQUIPMENT Pressure bar with rubber belt Panel stop with CNC positioning Panel infeed alignment system Edge heating lamps Roller magazine Hot melt adhesive reservoir Hot melt adhesive pre-melter 7 pressure rollers Trimming unit Flush trimming unit, top and bottom Edge rounding unit FF12 Profile trimming unit Scraping blade unit PN10 Glue scraping blade unit Brushing unit with spray device PC22 control The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External Reference: 6042

Condition: used, Year of construction: 2003, machine/vehicle number: 0-34-07-5949, functionality: fully functional, input voltage: 24 V, input current: 48 A, input frequency: 50 Hz, cutting height (max.): 320 mm, cutting width (max.): 60 mm, We offer this used HOMAG Optimat chf 41 circular table saw, year of construction 2002. Manufacturer: HOMAG Model: Optimat chf 41 Construction year: 2002 year Condition: used Category ID: 2094 Type ID: 1612 Machine type: circular table saw Godpfszq Hwhsx Afuekc If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: excellent (used), Year of construction: 2018, used horizontal panel dividing saw Manufacturer: Homag Type: Sawteq B-130 (Optimat HPP130/32/32) Year of manufacture: 2018 Cutting length 3200 mm Cutting width (program slider travel) 3100 mm Roller rail 1 * element, 10-track + 4 single-track Clamps 5 pieces Gksdez R Sgzjpfx Afuoc Air cushion table 3 * 1800 x 500 Central blower 1 piece Technical data: Saw blade overhang 60 mm Saw carriage feed: forward 1-60 m/min, reverse constant 60 m/min Automatic cutting height; pressure beam height control Angular backstop, min. pressure width 0 mm; max. pressure width entire cutting length Main saw motor 5.5 kW with pneumatic saw lift Scoring saw motor 1.1 kW, motorized saw lift, electric adjustment Operating voltage 400 V (+10%/-5%) / 50 Hz Electrical connection value: 10 kW Labeling program with label printer PICA II 103 Power Control CADmatic 4 control system Optimization program CAD-Plan 4 "Single Saw" on the machine

Condition: good (used), Homag BMG 316 L machining center Gksdpfjz R Dm Eox Afujc Working area: 4200 x 1550 mm 8 crossbars, each 1340 mm long 6 loading supports 8 front stops 5 rear stops in the machine base 4 side stops Suction cups: 160 x 155 h 100 mm Suction cups: 125 x 70 h 100 mm LED positioning system for workpieces and suction cups Electro-spindle, 5-axis, 10 kW, 13.5 hp, HSK F63 Liquid cooling Circular tool changer with 18 positions Drilling head with 17 vertical spindles, 7500 rpm 4 horizontal spindles with 125 mm blade, adjustable 0/90° Chip conveyor Tool transfer pick-up Collision control system CAD/CAM interface 2 Busch Mink MM 1144 BV vacuum pumps, 80 m³/h

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 5-axis CNC machining center as a cantilever table design Working area in X = 4375 mm Working area in Y = 1550 mm Working area in Z = 250 mm with 12 kW milling spindle, liquid-cooled 5-axis spindle Homag Drive 5 C+ max. speed 24,000 rpm with torque support Tool holder HSK F-63 18-position disc tool changer 17 drilling spindles, vertical 2 drilling spindles, horizontal in X 2 drilling spindles, horizontal in Y Notch saw, 90° swiveling with LED light strip as positioning aid with 2 vacuum pumps, each 300 m³/h with special workpiece clamping system for small parts with barcode scanner Safety device: bumper with chip conveyor Godpfsz Rrbwsx Afuekc with powerControl PC 85 control system with handheld operating device Software: Homag Woodwop 8.0 WoodScan CollisionControl Space requirement: approx. L x W x H 7650 x 4710 x 2850 mm Availability: approx. July 2027 Location: NRW (North Rhine-Westphalia)

Condition: used, machine/vehicle number: 008690, X axis working area: 3100 mm Y axis working area: 1410 mm Working Table: Pod and Rail Main Electrospindle power: 12 KW Number of controlled axes: 5 axes Godpfszwdkfjx Afuskc Total number of drilling spindles: 18 Total number of tool changer positions: 18