CPU RAM I/O board

HOMAG

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Table thickness: 60 mm. Thickness of coiled material: 3 mm Release agent application device Sanding unit Gluing unit Edge pressure unit End trimming unit Milling unit Edge rounding unit Edge scraper unit Glue scraper unit Cleaning device Brush unit Control: Homag powerTouch Ppsdoy Icgpspfx Al Sor

Condition: good (used), Year of construction: 1999, machine/vehicle number: 0-200-21-3286, functionality: fully functional, input voltage: 400 V, input current: 56 A, type of input current: three-phase, edge thickness (max.): 20 mm, Equipment: CE marking, Used single-sided HOMAG edge-banding machine for straight edges – KL 79/A20/S2 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the right side. Year of Manufacture: 1999 SPEZIFICATION & EQUIPMENT: Basic machine with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness max. 60 mm - top pressure with compound V-belt, motorized height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - clamping of glue application unit before rear end of workpiece, for even glue application - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clock-wise, counter clock-wise), 2x3.5kW, jumping function GLUING SECTION A20, consisting of: - QA34 glue application unit, on request with PTFE-coating (Teflon) - Pre-melter for EVA glues - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 6 non-driven pressure rollers. POST-PROCESSING SECTION: Pjdpsy H Hzbefx Al Sepr - Snipping (end-trimming) unit HL81, 2 motors, with straight/chamfer cutting function motorised fine-positioning of snipping stop - Pre-milling (rough trimming) 1,5 kW, top/bottom - Corner rounding FK13, 2 motors (top/bottom) with automatic 8-fold tool changer and several exchangeable trimming heads - Profile (radius-) scraping MN11, with auto-revolver positioning - Flat scraping (glue joint) FA10, top/bottom, (version with 3 tracer rollers) - Straight belt sanding unit KS10 - Buffing unit top/bottom ELECTRONIC CONTROL: - HOMATIC NC21 OPERATING SYSTEM

Condition: used, Year of construction: 2021, functionality: fully functional, For Sale: HOMAG SAWTEQ B-200 (HPP200/32/32) — Automatic Panel Saw We are offering a HOMAG SAWTEQ B-200 automatic panel saw, model HPP200/32/32 — a high-precision machine designed for cutting both laminated and unlaminated panels from wood-based materials. Machine highlights The saw features a motor-adjustable pre-scoring unit, a 21" Full HD multitouch display, and HOMAG's CAD MAtic control system with 2D and 3D cut plan visualisation. Positioning is handled by a maintenance-free electromagnetic system with ±0.1 mm accuracy. Remote diagnostics are available via TeleServiceNet. Pjdpsy Huv Tsfx Al Sjpr The saw carriage runs at 1–80 m/min and is driven by a toothed belt and gear system — no lubrication required, no resonance effects, and precise positioning guaranteed. A 10-year warranty is included on the carriage guides. The pressure beam provides identical pressure across the full panel width, eliminating parallelism errors and material damage. The optimised dust extraction keeps emission levels well below prescribed limits. Technical specs Cut length 3,200 mm, cut depth 3,100 mm, blade height 65 mm, working height 920 mm. Main motor 7.5 kW (optional 9.2 kW). Power supply 400 V / 50 Hz. Air pressure required: 6 bar. Included with the machine The sale includes an 11 kW main saw motor (50 Hz), 4 manual stops for pre-laminated pieces, 3 roller elements for the front table, CAD Plan 4 cut optimisation software, pressure beam height control, Slovenian-language documentation and on-screen texts, and packaging. The machine is CE certified, GS tested, and complies with BGI 739-1.

Condition: ready for operation (used), Year of construction: 1996, cutting length (max.): 3,800 mm, Panel saw manufactured in 1996. This HOMAG HPL 11/38/22 features a cutting length and width of 3800 mm, with a lifting table payload of 7 tons. It includes 7 clamps and automatic height control for efficient panel feeding. If you are looking to get high-quality panel cutting capabilities, consider the HOMAG HPL 11/38/22 machine we have for sale. Contact us for further details. Ppjdjy Hr Nkjpfx Al Ssr • Cutting width (program pusher travel): 3800 mm • Clamps: 7 units (with 2 optional additional clamps possible at positions 150/350) • Clamp spacing: 50 / 250 / 450 / 850 / 1550 / 2250 / 3050 mm (measured from angular fence to clamp center) • Air cushion tables (front of machine): • 1x at angular fence: 2810 x 650 mm • 2x: 2160 x 650 mm Additional equipment • Lifting table for batch-wise panel feeding: • Dimensions: 3800 x 2200 mm • Payload: 7 tons • Stacking height (floor level): max 680 mm • Stacking height (in-pit installation): max 880 mm • Automatic height control via control console • Heavy-duty roller conveyors (2x): Type HER 38/22 L, non-driven, longitudinal transport, forklift slots, 18 rollers, height 330 mm, roller Ø 108 mm, spacing 198.5 mm • Roller conveyor drive units (2x): Type 38/22, speed 12 m/min • Stacking station: LIFT-EX Type HAZ Ausf. A for stacking divided formats • Label printing system

Condition: ready for operation (used), Year of construction: 2016, Edgebander manufactured in 2016. This HOMAG KAL 370 features a continuously adjustable feed speed of 18-20 m/min and accommodates workpiece thicknesses from 8 to 60 mm. It includes advanced gluing and trimming units, as well as a comprehensive software package for efficient operation. If you are looking to get high-quality edgebanding capabilities, consider the HOMAG KAL 370 machine we have for sale. Contact us for further details. • Feed speed: Continuously adjustable 18–20 m/min • Fixed stop side: Left • Workpiece thickness: 8–60 mm • Workpiece overhang: 30 mm • Throughput equipment: Pre-installation for Boomerang TFU140 • Feed lock: Available • Feature packages: Future-Paket 5; Foil/High-Gloss Package (bottom) • Infeed features: Sliding carriage; Workpiece alignment at infeed; Workpiece support with roller track; Infeed barrier • Workpiece transport: Transport device; Top pressure • Cleaning/Prep: Release agent spraying unit (top/bottom) • Jointing/Milling: Joint trimming unit; I-System-DIA jointing cutter set WD60; Workpiece pre-heating (up to 60 mm thickness) • Gluing: Gluing unit; Preparation for Airtec activation unit; Adhesive application system; Application units QA60 and PU60; Pressure tank for PU application unit • Magazine/Pressure: Edge magazine; Pressure zone • Spraying: Lubricant spraying unit (top, bottom, side) • Trimming/Milling: Snipping unit HL81 (bevel/straight, 0.8 kW); Pneumatic adjustment for flush/overhang trimming; Pre-milling unit BF10; HM milling cutter set (straight); Form milling unit FK11 • Tooling/Changeover: I-Exchange head system (automatically adjustable/FK); I-DIA radius cutter set (for FK, R=2 mm, Z=4); Standard milling unit SF21; Multi-profile scraper MN21 (automatic); Profile knife set for MN20/21 • Additional units: Joint scraper FA20 BASIC; Automated scanning for joint FA20; Buffing unit FA06 (top/bottom); Powercontrol PC23 Powertouch • Control/Software: Software package WoodCommander; Antenna sequence control; Machine data acquisition and evaluation; Error diagnosis; Teleservicenet-soft • System/Networking: Emergency stop interlock; Network connection (Ethernet); Manual control for setup mode; Language: German • Documentation: On data carrier and paper Ppedpfx Aljy Hrtpe Ssr Additional equipment • Boomerang return system TFU140/20/08-Optimat • Workpiece detection (sensor-based) • Basic outfeed return line • CE for cells (systems)

Condition: ready for operation (used), Year of construction: 2010, number of axes: 4, This 4-axis HOMAG BAZ 211/40K was manufactured in 2010. It features a vacuum clamping system with multiple configurations, a powerful vacuum pump, and a Flex5+ sawing, milling, and drilling aggregate. The machine is equipped with three tool changers and an edge banding package for enhanced processing capabilities. If you are looking to get high-quality CNC wood machining capabilities, consider the HOMAG BAZ 211/40K machine we have for sale. Contact us for further details. • Vacuum clamping system: 8x 120x50 mm (0/90°) K-Table • Rotating vacuum clamping system: 8x 125x75 mm (360°) K-Table • Vacuum pump: Reinforced 100/140 m³/h • Aggregate: Flex5+ sawing, milling, and drilling aggregate for tool changer (WZW) • Tool changers: 3x tool receivers for Flex5+ (WZW) • Edge banding package: Power EDGE 360° for BAZ 211/311 Venture • Edge processing: Workpiece edge blow-off nozzle • Milling/Scraping: Combination flush milling and scraper aggregate (WD 60 mm) • Profile blades: 2x for scraper • Radius cutter head: 2x WPL radius cutter head Ppjdpey Hrr Esfx Al Ser • Material handling: Tool transfer station for B200/300/K • Software: Upgrade to woodWOP 6.0

Condition: good (used), Year of construction: 2006, functionality: fully functional, CNC MACHINING CENTER WITH EDGE BANDING UNIT AND ASSOCIATED POST-PROCESSING AGGREGATES. Technical Data: Working dimensions: + X-axis: 3,050 mm for single setup + X-axis: 900 mm for pendulum operation + Y-axis: Milling up to 1,220 mm with 25 mm tool diameter Edge banding up to 1,220 mm All aggregates up to 1,170 mm Workpiece thickness up to 60 mm with standard clamp 6 workpiece consoles for a tubeless vacuum system 4 workpiece stops in X-direction, integrated into the machine frame, for large workpieces 6 workpiece stops in the X-direction, one each integrated in the console 1 workpiece stop each on the left and right in the Y-direction 4 lifting rails for easy positioning of heavy workpieces LED positioning aid for easy placement of vacuum cups and consoles Aggregate equipment: Milling spindle 11 kW, HSK F63 Speed range 0 - 18,000 rpm Ppjdpey Hrh Tofx Al Ser Liquid cooling C-axis for use with processing units, with torque support and 3-point stabilization 12-position tool changer magazine Drilling head with 17 vertical spindles Spindle pitch 32 mm Air nozzle for cleaning workpiece edges Exchangeable edge banding unit for 360-degree edgebanding work With single-roll magazine With granulate feed Edge thickness up to 3 mm Adapter aggregates: + Horizontal boring head in cross-head design + Lock case milling unit, 2 outlets + 90-degree sawing unit + Swiveling drilling/sawing unit + Combination unit for radius milling / scraper blade Control system: POWERCONTROL with: WOOD WOP AV license WOODWOP

Condition: used, Year of construction: 2007, operating hours: 39,359 h, functionality: fully functional, machine/vehicle number: 0-201-04-0605, Description of the Main Equipment: Clamping table with matrix aluminium construction Vacuum system prepared for 1000 m³/h nesting technology Power Control control panel with PC85 Main spindle 15 kW with vibration sensor C-axis with aggregate interface Interface for FLEX-5 aggregate Ppedpfx Ajyucyzjl Ser Plate-type tool changer with 10 positions Drilling unit: 13 spindles – 9 vertical and 2+2 horizontal spindles Software package for office computer WoodWOP Tools software Maximum positioning speed: 80 m/min in X and Y directions (vector speed: X/Y = 113 m/min) / 30 m/min in Z direction

Condition: ready for operation (used), Year of construction: 2012, workpiece width (max.): 60 mm, product length (max.): 7,845 mm, Edgebander manufactured in 2012. This HOMAG KAL211 Edition 2264 features a working height of 950 mm and accommodates workpiece thicknesses from 8 mm to 60 mm. It includes various units such as a gluing unit, joint trimming unit, and pre-milling unit, enhancing its versatility. If you are looking to get high-quality edge banding capabilities, consider the HOMAG KAL211 Edition 2264 machine we have for sale. Contact us for further details regarding this machine. • Feed speed: 18–25 m/min • Feed speed (max with FK11 unit): 20 m/min • Working height: 950 mm • Pneumatic connection: 6 bar • Total length: 7845 mm • Workpiece width (min): • 60 mm at 12–22 mm thickness • 105 mm at 23–40 mm thickness • Workpiece thickness: 8–60 mm (extended via options • Edge material thickness: • Rolls: 0.3–3 mm • Strips: 0.4–20 mm • Electrical: • Supply voltage: 400 V / 3 Ph / 50 Hz • Total load current: 67 A • Control voltage: 24 V • Control system: powerControl PC22 (Windows XP based) • Software: woodCommander; woodScout (option); Schuler MDE Basic • Aggregates/units: • Separation agent spraying unit (top/bottom) • Joint trimming unit (2 motors, 4 kW each) • Gluing unit A20 with 2 rollers (Quickmelt system) Psdpoy Hi Eisfx Al Sopr • PU65 application unit (exchangeable, Teflon coated) • Preparation for laserTec activation unit • End trimming unit HL84 (0.8 kW) • Pre-milling unit BF10 (1.5 kW) • Multi-profile form milling unit FK11 (manual adjustment) • Profile scraper PN10 • Finish unit (glue joint scraper + buffing unit) • Cleaning agent spraying unit Additional equipment • Automation package (No. 4013): • Automatic adjustment of infeed fence and pressure zone • Electronic height adjustment for the top pressure beam

Condition: excellent (used), Year of construction: 2018, Chassis for edge banding machines Was mounted on Homag Edgeteq S-200, KDF 1130 FC (1100kg). Will certainly also fit other machines, such as Brandt (minor modifications may be necessary) Psdpfow S Dmdex Al Sjpr Length of U-section: approx. 1130mm Overall height incl. castors: approx. 150mm 4 sturdy steel swivel castors with grease fittings 2 locking brakes 2 leveling plates for height adjustment Machine can be demonstrated on site by appointment. We only offer machines that are ready for demonstration in our warehouse, see "more offers from this seller".