Pipes - and profiles

IDE Kabelkanal Werkzeuge

Condition: good (used), Year of construction: 2010, product length: 600mm - 1300mm Lhelhcdwsm Dqk Us Ded product width: 185mm - 400mm

Year of construction: 2025, Condition: new, machine/vehicle number: 30632, IDE-o/c 12002675 SINGLE SCREW CO-EXTRUDER MEB 30/5x25D (picture similar, here shown MEB H20/5x25D) Lhslju Tgriehcdw Djd - NEW machine from IDE-stock program - international size 1-30-25 - mobile on 4 swivel castors - manual height adjustment +300/-100 mm via threaded spindle - control cabinet integrated in the frame * incl. connection cable 5m long, 32 A CEE - control via PLC Control 20/4 with 7" touch panel * drive on/off * display screw speed * display motor load * heating on/off/lowering value * set value either via touch display or digital potentiometer - emergency stop button on the control cabinet - AC parallel shaft helical geared motor 5.2 kW air-cooled, in Z-design - screw speed max. 88 rpm - screw back pressure max. 300 bar (temporarily 350 bar) - one-piece cylinder (nitrided) with water-cooled feed zone - 3 cylinder heating zones with 3 cooling fans - material hopper, 6 liter volume, fix mounted on barrel - die connection M22x1,5 screw Ø 30 mm x 25 D - Screw for processing PVC-F - screw design acc. to drawing 1258060 - output range 1.5 to 8.0 kg/h, depending on tool back pressure - nitrided and polished, with integrated screw tip - screw take-out to the front (in extrusion direction) 4 additional heating zones - display in extruder control - sockets CEE 230V, temperature probe FeCuNi Typ L - 1 additional heating zone with heater band for union nut - 1 additional heating zone for heating hose (without heating hose) - 2 die heating zones, without heating element (as spare) melt pressure and temperature measurement - combination probe ½"-20UNF-2B, cable pluggable - pre-warning 250 bar / shutdown 300 bar - visualization in ME Control 20/4 extruder control

Condition: good (used), Year of construction: 2001, - Manufacturer: IDE - Type: 45/4 - Year of manufacture: 2001 - Monovis Ø45mm 25LD - Right-hand analog control - Screw profile: PVC - 4 heating zones on cylinder Lhelhcsuhpiyedw Djd - 4 tool heating zones - Motor power: 8.5kW - Up to 60kg/h Good overall condition, very clean machine

Condition: used, Weld beveller, weld bevel former, weld seam preparation, weld bevel forming machine, edge milling machine, edge milling machine, mobile milling machine Lhjlhcjd Nzgvjdw Dod -Edge milling: 0 - 3 mm -Drive: 0.45 kW -Angle: adjustable -Dimensions: 485/345/H250 mm -Weight: 18.2 kg

Year of construction: 2025, Condition: new, machine/vehicle number: 30630, IDE-o/c 12002673 SINGLE SCREW CO-EXTRUDER MEB 20/5x25D - NEW machine from IDE-stock program - mobile on 4 swivel castors - manual height adjustment +300/-100 mm via threaded spindle - control cabinet integrated in the frame - control via PLC Control 20/4 * operation via 5.7" touch panel * screw on/off * screw speed * screw speed display * display motor load * heating on/off/lowering value - emergency stop button on the control cabinet - incl. connection cable 5 m long with CEE plug 32 A - AC parallel shaft helical geared motor 2.6 kW air-cooled, in Z-design Ljlhceu Tgrpodw Dohd - screw speed max. 92 rpm - screw back pressure max. 300 bar (temporarily 350 bar) - one-piece cylinder (nitrided) with water-cooled feed zone * integrated pressure disc for overpressure protection - 2 cylinder heating zones with 2 cooling fans - die connection M22x1,5 with union nut - 1 additional heating zone with heating band for union nut - 1 additional heating zone for heating hose (without heating hose) - material hopper, 6 liter capacity, fixed on cylinder - 1 additional socket SCHUKO 16A for hopper conveyor screw Ø 20 mm x 25 D - Screw for processing PVC-F - output range 0.5 to 5.0 kg/h, depending on tool back pressure - nitrided and polished, with integrated screw tip

Year of construction: 2002, operating hours: 73,587 h, Condition: ready for operation (used), machine/vehicle number: 300, CO-EXTRUDER MEB 38/2 x 25 D - used machine, function tested, ready to use -Chassis with swivelling device and height adjustment - DC drive 5,2 kW - Screw speed approx. 60 min-1 - 1-part cylinder, made of nitrided steel incl. water-cooled inlet zone - 4 cylinder heating/cooling zones with 4 air blowers - 1 connection flange heating zone with controller, switching element and heating element - 1 mould heating zones without heating element - Feed hopper made of V2A * Capacity approx. 12 litres * Sliding mechanism Mould connection - flange system IDE, incl. thread M 30 x1,5 Control cabinet / electrics - permanently attached to the base frame * incl. circuit for bridging short-term power failures Compact control mini ME Control /3 * Mounted in portable housing with 3 m connection cable to the control cabinet - Screw on/off - Screw speed via digital potentiometer - Screw speed display Lhelhsu Tgrcocdw Djd - Motor load display - Heating on/off/lowering value 1x screw Ø 38mm x 25 D - 3 zone screw for processing PVC - Nitrided and polished - Screw tip suitable for mould connection

Year of construction: 2001, operating hours: 55,378 h, Condition: ready for operation (used), machine/vehicle number: 15, SINGLE SCREW EXTRUDER ME90/4 x 25 D - used machine, checked and ready for operation Lhslhcsu Tgqxsdw Ded - open frame construction with spur gearing and directly flange motor - DC-drive 50 kW - screw speed max. 38 rpm - 1-part cylinder, smooth with water-cooled entryzone - 6 heating and cooling zones - 1 flangeheating zone - 5 die heating zones, without heater - die connection incl. heater band - electrical cabinet mounted on operation side * incl. short interruption device 0,5 sec. - additional Sockets * 1 CEE-socket 5-pole 400V, 32A * 2 Schuko-socket 230V, 16A - temperature controller type KS40, with self-optimisation - operation panel swivelling - melt pressure and -temperature measuring incl. 2 probes 1/2" - 20 UNF - hopper 100L with 3-pos. svievel mechanism - incl. screw for processing PVC-U granule * nitrided , polished and hollow bored - incl. screw tip tempering system * incl. oil tempering unt

Year of construction: 2013, Condition: ready for operation (used), machine/vehicle number: 248, CALIBRATION UNIT ME16/6.2 - used machine (IDE-Technikum), checked and ready for operation Ljlhcdju Tgrvjw Dshd - mounting platform 3950mm x 700mm - motorized length adjustment 500mm - motorized height adjustment 875 - 1025mm - manuell cross adjustment, 50mm - 2 vacuum pumps - 2 manifold with each: * 20 water connections 1/2" * 20 vacuum connections 1/2"

Year of construction: 1996, Condition: ready for operation (used), machine/vehicle number: 455, HAUL-OFF UNIT ME 30/4 - used machine, checke and ready for operation - 2 DC drives 1,1 kW each - haul-off speed up to 50,0 m/min - contact length approx. 800 mm - pneumtic clamping * weight compansation for upper haul-off carrier * compansation tank for pressurized air - 2 haul-off belts 75 mm wide - protection cover mit Folding door, endschaltergesichert, Lholhcdweu Tgr Nj Dod * without inlet protection tunnel - control panel with 12 m connection cable - incl. short interruption device

Year of construction: 1992, Condition: ready for operation (used), machine/vehicle number: 154, CALIBRATION UNIT ME16/6.2 - used machine (IDE-Technikum), checked and ready for operation - base frame 3,0m long - mounting platform 2500mm - manuelle length adjustment, with handwheel - manuelle height adjustment, with ratchet - manuell cross adjustment, with hand wheel - 2 vacuum pumps - 2 manifold with each: * 10 water connections 1/2" * 10 vacuum connections 1/2" Lholhcou Tgr Asdw Djd

Condition: used, Year of construction: 1999, Functionality: fully functional, machine/vehicle number: 90, PUNCHING UNIT ME 41/2 - Used machine, function-tested - Frame l x w 1000 x 600 mm - Height adjustment with spindle - Travelling distance approx. 25 mm, pneumatically supported - pneumatically operated - Punching force 1,800 N / at 6 bar - Punching stroke length 10 mm - Punching sequence max. 150 strokes/min - Trigger pulse electrical - Without punching tool - Protective panelling with hinged door Limit-switch protected, without infeed/outfeed protection channel - Removable waste container Lhjlhcdotx Awusw Ded Length measurement - with contact roller and holder for punching step 64 mm - with contact roller /0 20.38 mm with one switching cam

Condition: used, Year of construction: 2004, Functionality: fully functional, machine/vehicle number: 756, PUNCHING UNIT ME 40/6.3 - Used machine, function-tested - Working principle pneumohydraulic - Travelling distance: 200 mm, pneumatically supported - Punching force 24 KN at 6 bar - Punching/power stroke: 50/12 mm Ljlhjtx A Akocdw Dohd (power pack S4.50.12D) - Punching sequence max. strokes/min.: 40 (depending on profile and speed) - End position monitoring by limit switch - Installation dimensions for punching tool: (w x h x l) 180 x 138 x 225 mm - Protective panelling with hinged door, limit switch protected - Without inlet/outlet protection channel - For mounting a column guide frame 350x 250x 250 mm * without column guide frame - without punching tool - incl. sequence control for external punching release (24V signal, potential-free required)

Year of construction: 1996, Condition: used, Functionality: fully functional, machine/vehicle number: 465, HAUL-OFF UNIT ME 30/4 - used machine, function-tested - Driven by 2 GS motors 0.8 kW each - Pull-off speed 0.5 to 10 m/min - Pull-off force max. 4,500 N - Caterpillar clamping pneumatic, weight compensation of the upper crawler carrier, Equalising tank for the compressed air supply - 2 transport chains 75 mm wide, 23 mm high, hardness approx. 70 Shore A profiled for roller shutter standard profile (smooth segments possible) Lhelhcdjtx Axrsw Ded - Protective panelling, limit switch protected - Control panel with approx. 12 m connection cable - Fixed extrusion height 1100 mm Central chain lubrication

Condition: used, Functionality: fully functional, machine/vehicle number: 460, Year of construction: 1997, EXTRUDER ME 45/3x25D - used machine, function tested - DC drive 14 kW - Screw speed 8-85 min-1 - Cylinder, one-piece, with water-cooled feed zone - 4 cylinder heating/cooling zones with 4 air blowers - 1 flange heating zone, incl. heater band - 3 mould heating zones, without heating elements - Three-point temperature controller type KS 40 with digital display, self-optimisation and error message - die connection in special design with external thread M 85 x 2, designed for melt pressure and temperature temperature measurement Mass pressure and temperature measurement - complete with 2 separate measuring probes - digital display units - incl. 2 blanking plugs Hopper - capacity approx. 60 litres - swivelling mechanism 1 Screw ø 45 mm x 25 D - 3-zone screw for processing Lhelotx Av Rohcdw Dod Polyamide as per drawing 22501850 - Output capacity approx. 8-35 kg/h (depending on mould design) - Nitrided, polished and hollow drilled - Screw tip suitable for mould connection

Year of construction: 2007, Condition: good (used), Description Brand Eco Refrigerazione Model IDE 43B10 ED ID 555804 Status Active Lhelhcjdxwrpjdw Ded Price 1.300 € + VAT Year of manufacture 2007 Location Oradea (RO) Industrial dual discharge unit cooler Eco IDE 43B10 ED manufactured in 2007, recommended for applications in large cold rooms and refrigerated storerooms. Maximum airflow: 12300 m3/h, air throw: 2 x 14 m, heat exchange surface (int./ext.): 83 m2, 3 fans (450 mm), electronic defrost (1500W). Lowest temperature: -35oC. ExWorks. Price is negotiable. Technical inspection can be organized at least 24 hrs before the due date We speak English. Wir sprechen Deutsch. Hablamos Español. Beszélünk magyarul. Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervam dreptul la greseli, modificari si vanzare prealabila.

Condition: ready for operation (used), Year of construction: 2004, Functionality: fully functional, machine/vehicle number: FH.FNJF-00296 / 1224402827, paper weight (min.): 40 g/m², paper weight (max.): 250 g/m², paper width (min.): 150 mm, paper width (max.): 780 mm, paper height (min.): 180 mm, paper height (max.): 1,200 mm, No reserve price - guaranteed sale at the highest bid! TECHNICAL DETAILS Lslsv Imuxjhcdw Dohd Maximum paper format: 780 x 1,200 mm Minimum paper format: approx. 150 x 180 mm Paper weight: 40 - 250 g/m² Maximum mechanical speed: up to 230 m/min Folding types: parallel fold, zigzag fold, altar fold, window fold, etc. EQUIPMENT - 6 folding pockets for versatile folding types - 1 blade for additional folding options - Heidelberg PFH-82 pallet feeder for continuous sheet feed - Steel vertical sheet delivery SBP 66.D-MKE for precise sheet placement - Automatic settings for quick job changes - Touchscreen operation for easy control

Condition: excellent (used), Year of construction: 2022, Max. sheet format: 66 x 128 cm (RFH) 66 x 104 cm (FFH, PFH) Min. sheet format: 14 x 18 cm / 20 x 18 cm with double suction wheel Max. folding speed: 230 m/min in parallel folding Pockets: 6 Knives: 2 Operating hours: 2423 h Equipment / Additional information: Feeder PFH-66 Pocket folder BUH-66, 1st station Cross folding machine CUH-66 Lhslhcdwsv Stcke Dsd

Condition: used, General SKU: 204U042 Location: Barneveld Make: Werner&pfleiderer Type: ZSK70F175E .: 231783 Ljlhcdjv Aikxsw Dehd Sizes Screw diameter: 70mm Main Features Motor: 108KW L/D: 23 Specified Features - Double screw extruder Material: Nichrome2.4869 Double screw extruder: ✔ Screw diameter: 70mm L/D: 23 Co-rotating: ✔ Water cooling: ✔ AC-motor: ✔108kW,330Volt,1500rpm With variable speed drive: frequencycontroller Screw speed: 198rpm Exchangeable segments: ✔(notincluded) Information Year of construction: 1996(gearbox2017) With switchgear: ✔ Sizes switchgear: 1,25x0,7x2,15m Total height: 1,7m Floorspace: 4,6x2m Weight: 6400kg Extra Specifications: inlet:142x130mm -thereare2screwshaftspresent-noscrewsegmentspresent-noextruderhe adpresent What you can expect from Foeth: all our machines are in working condition, and at a reduced price compared to new. They are ready for shipping to any destination worldwide. You are welcome to inspect our machines in Barneveld, The Netherlands. Please visit our Foeth website for more information about this machine.

Condition: excellent (used), Year of construction: 2014, Functionality: fully functional, working range: 3,100 mm, working width: 1,500 mm, table length: 3,100 mm, For sale: 1 used plasma cutting machine Manufacturer: Air Liquide Type: Plasmatome 20B YEAR OF MANUFACTURE: 2014 Table size: 3.1000 x 1.500mm Burns up to 20mm mild steel Ljlhcstnc Sfedw Dehd Incl. documentation, very well maintained condition. Machine can be inspected in our warehouse in 09599 Freiberg.

Condition: used, machine/vehicle number: 005449, Position 1: Panel Tipper MORBIDELLI-FLEXA 912+FLEXA 902 Lhjlhcdwsuyp Ddo Dod Position 2: CNC for Flexible Drilling MORBIDELLI-FLEXA 912+FLEXA 902

Condition: ready for operation (used), Heidenhain EXE-PLATINE 3-axis .: 257 411 01 , :6972758 as per photo, used, normal signs of use, 100% functional, scope of delivery as per photos Lholoi Eainjhcdw Ded

Condition: excellent (used), Functionality: fully functional, Heidelberg Versafire / Ricoh C7200x + Prinect controller + Finisher Lhelhov Sbkcscdw Djd +DOHCF + 5th Colour

Condition: good (used), turning diameter over bed slide: 600 mm, turning length: 3,000 mm, overall weight: 3,850 kg, Turning diameter over support: 370 mm Max. working travel of the bottom slide: approx. 350 mm Lolhcev Sazaedw Dshd Max. working path of the top slide: approx. 125 mm Speed range: 18-900 rpm Main spindle with camlock spindle head size 8 Machine dimensions approx. (LxWxH): 5,500 x 1,400 x 1,500 mm

Condition: good (used), Year of construction: 2011, max. size 37 x 52 cm age 2011 Ljlhcdwjv R Ulwo Dohd Onpress Center (CP-Tronic) Alcolor film dampenings cooling unit Baldwin BasicLiner incl. BalControl automatic washing devices EasyPlate dry sprayer PowderStar + version shown totalizer: approx. 39 mill. impressions Delivery time: immediately

Condition: excellent (used), CATALOGUE NUMBER 6059 TECHNICAL DATA - number of horizontal spindles 2×20 pieces - number of vertical spindles 1×20 pieces - spacing of extreme spindles 610mm - spacing between spindles 32mm - feed cylinder stroke 60mm - max. length of processed element 3400mm - adjustment of horizontal spindles up/down, front/back - adjustment of vertical spindles right/left - possibility of working on each drilling device separately - right-left drills, mounted on a thread (screwed in) - 3 pneumatic clamps - engine power 4×1.85kW - air demand 6-8 bar - dimensions length/width/height 4600x1180x2200mm - weight approx. 1500kg Ljlhcdwegq I I Ee Djhd Net price: 15900 PLN Net price: 3740 euros depending on the price, 4.25 euros (Prices may vary with higher fluctuations)