Gluing press

Joos HP-S 80

Condition: as good as new (ex-display), Year of construction: 2020, pressing force: 160 t, Hydraulic 160 T double cylinder insertion press Double column press- two cylinder press with 160 T capacity at 250 bar. a) idle speed downward 9,8 mm/sec. b) upward speed up to 15,0 mm/sec. c) table size 1500x600x100 mm, height adjustable d) ram plate, 1500x600x100 mm e) year of construction 12/2020 f) motor power 11 KW g) pump capacity 22 L/minute h) travel limitation by cam switch i) Open height 700 mm j) ram travel 500 mm k) Remote control via two-hand operation l) Pressure setting via rotary control from approx. 30 to 160 T m) Approx. height 2800 mm n) T-slots according to customer requirements o) Weight approx. 4,200 kg p) Oil tank with approx. 200 L volume q) Painting in RAL 5005 ( royal blue ) or according to customer's request. r) For safety reasons the ram plate is painted orange RAL 2009 or signal yellow RAL 1023 s) Assembly, commissioning, instruction can be provided at a separate charge. The travel can be adjusted by cam switches. The ram/table size of the machine shown is 1600x600x100 mm. Ledegz H Dhjpfx Al Toru

Condition: used, MULLER 250t Lsdpfx Aerfxhkjl Toru PRESSURE: 250t STROKE: 550mm TABLE DIMENSIONS: 2500x1400mm

Condition: new, Year of construction: 2018, machine/vehicle number: DF0199 - Rev.00, pressing force: 160 t, pressure:160 t passage width:1200 mm stroke:600 mm Ljdpfx Aodxvfhsl Teru Weight of machine approx.:7 t dimensions:ca. 2400 x 1400 x 3400 mm return capacity:16 t Max Working height:800 mm Return Speed:25 mm/sec pestle plate:1670 x 800 mm table plate:1670 x 800 mm table height over floor:800 mm Oil cooling (electric):1,5 kW (max) Engine Output:18 kW speed of forward flow:10 mm/sec pressure speed:10 mm/sec Travel:600 mm Oil Tank Capacity:300 l

Year of construction: 2012, condition: used, Hounsell down stroke Hydraulic forming press H frame Year 2012 200ton Daylight 750mm Nominal Lsdpof A R Uhsfx Al Tsru Table size W x L 2100mm x 1200mm Max Weight top tool 800kg Max system Pressure 340 bar Ram diameters 110mm Number of Rams 6 Seal Dimensions 110 x 130 x 16 Machine construction fabricated frame Machine weight 95000 kg approx Approach speed 150mm/s Pressing speed 8mm/s Return speed 80-90mm/s Can quote for new hydraulic presses c and h frame

Condition: used, Machine not operational - control system not functioning Available at a special price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Factory No. 300487, Year of Manufacture 2006 Pressing force: 500 tons Distance between columns (front and rear): 2520 mm Table area: 2500 x 2500 mm Ram area: 2500 x 2500 mm Ram stroke: 600 mm Maximum installation height: 600 mm Table height above floor: approx. 900 mm Tank capacity: approx. 1000 liters Ram retraction force: approx. 22 tons Adjustable forward speed: 100-800 mm/s Pressure build-up to 5000 kN: approx. 0.7 sec. Return stroke speed: approx. 300 mm/s Main motor power: 75 kW Lrjdpfx Ajdzqptsl Tou Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - 8-fold flat guide for the ram - Hydraulic ram locking in the top dead center position - Adjacent control cabinet (200 x 50 cm) - Electrical control system SIEMENS PLC S7-314 - Operation via SIEMENS OP 170-B (5.7") - 2-hand control panel located beside the machine - Floor-level installation - Table top 2510 x 2530 x 135 mm (approx. 6700 kg) - Central lubrication system - Operating manual with circuit diagrams Space requirement (L x W x H): 372 x 260 x 460 cm Space requirement for horizontal transport (L x W x H): 460 x 372 x 260 cm Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition.

Condition: new, neu ca. 4 Monate ab Auftragse Italien 172500 € 3260.25 € 300 to 500 mm 1250x1000 mm 600 mm 22 mm/s 2 mm/s 7.5 kW 1750 mm 1500 mm 2800 mm 4-pillar guide ram guide round table and ram with T-slots 2 hand operation Siemens PLC manometer users manual OPTIONS: Light barrier € on Request Siemens touchscreen-control, 50 programsstoreable, for programming: • Upstroke and downstroke quota • Break time in the bottom • time of Decompression • setting pressure of work • Pieces counter • prestop in upstroke and downstroke • setting for movement in manual and in automatic • management of alarms and anomalies € on Request Working hour counter € on Request Stroke counter € on Request Decompression valve € on Request Lodowir Acopfx Al Tsru Oil cooler with decompreission valve € on Request Pressur switch € on Request