Bed Type Milling Machine - Universal

KEKEISEN UBF400/15

Condition: good (used), travel distance X-axis: 12,000 mm, travel distance Y-axis: 7,300 mm, travel distance Z-axis: 3,000 mm, total length: 30,000 mm, table length: 12,000 mm, table width: 4,730 mm, total width: 12,000 mm, total height: 10,475 mm, table load: 250,000 kg, overall weight: 400,000 kg, Make : Waldrich - Siegen - Typ : PF-F-150(1)-530/400 - No. : 11.093/0 - Age : Overhault 2004 ( Euro 2.2 Mil) X Travel : 12.000 - Y Travel : 7.300 - Z Travel : 3.000 - W Travel : 4.000 - Between column : 5.000 - Table width : 4.730 - Table length : 12.000 - Table load : 19 t / mtr. Ca. 250 ton - Table feed : 10.000 mm/min. - W axis : 3.000 mm/min. - T axis : 6.000 mm/min. - Cross adj. milling head : - Vert. adj. cross rail : - Horizontal hydrostatic spindle ram - Milling spindle Ø : 560 - Milling tool taper : iso 60 - C axis feed : 5.000 mm/min. - Milling motor : 90 kW - Spindle speed : 2.500 R/pm - Z axis stroke : 3.000 - Z axis feed : 2.000 mm/min. - Milling Küma Angle head WF2 90 kw- 450 - Milling Küma Uni. UB1D 60 kw - 2400 - Milling Küma Fixed GB1D 90 kw- 2400 - Milling Küma Angle head WF1? - Electric requirement : 3 x 400 V / 50 Hz - Power requirement : 600 kVA / 630 Amp - Capacity 4.000 L coolant true spindle 20/40 Bar Machine is rebuild in 2004 by Schiess Bed – Table assembly group: * Renewal of sliding lining * Grinding of guideway * Renewal of table drive * Direct linear measuring syst. Nedoytrxkspfx Ac Dolh * Hydrostatic Portal and cross rail: * Modification of adjusting spindle trape Zoidal spindle was recplaced with ball screw * Direct linear measuring syst. * New drive motors for relization of higer speed on feed axes of milling support. * New milling support with hydrostatic guideways Electric system: * Complet elctric cabinet switchgear * Complet new wire * Siemens Sinumrik 840 D in 6 axis !! Equipment / parts : * Complet new raumag janich covers * Complet new double chip conveyor * Complet with big tooling packet * Complet with big mounting equipment - Under power in Europe - Free directly - Controlled axis X / Y / Z / W / C / B axis - Over all height : 10.475 mm - Over all width : 11.934 mm - Over all length : 30.000 mm - Total weight : ca. 400.000 Kg Rebuild in 2004 for EUR 2.200.000 !This CNC Waldrich Portal milling machines was used in the Energie Field for steam turbien case machining. Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2013, x-travel 30000 mm y-travel 3600 mm z-travel 1900 mm Control Heidenhain type TNC 530 i turning speeds 4000 U/min conus taper DIN 69871+AD mm Feed 10000 mm/min spindle drive 46 kW Rapid movement 25000 mm/min chip conveyor 2 St. Plate area 31000x2500 mm total power requirement 85 kW Nlsdpjyqtnnsfx Ac Djh Soraluce No. 5619 Load hours 9332 On-time hours 27960 Panel array consists of: 1 panel 7000x2500 mm 4 panels 6000x2500 mm Optional: 4x clamping angles Tool package Clamping table The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Year of construction: 1990, condition: ready for operation (used), A CNC universal milling and drilling center SHW is available. Travel X/Y/Z: 6000mm/2100mm/1500mm, milling head swivel: 180°, rapid traverse X/Y/Z: 8m/min, speed: 4500rpm, spindle power: 31.5kW, machine dimensions X/Y/Z: approx. 11000mm/9000mm/6000mm, weight: approx. 44000kg. Documentation available. On-site inspection is possible. Nljdpfxjuh Azie Ac Dsh

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, Double Column Milling M/C - Gantry Type Brand: FOREST-LINE ALBERT / Type: MODUMILL 300G / Year of construction: 1999 Extensive modernizations in 2008 and 2021 ! Nlodpfxszfbi Io Ac Dsh Machine with interchangeable vertical and horizontal milling heads with automatic indexing. The machine can be inspected by appointment. Very well-kept, continuously maintained condition! TECHNICAL DATA: - CNC Control: SINUMERIK 840D - Travels X/Y/Z: 11.450 / 3.500 / 1.250 mm Cross-section of the Z-axis slider: 360 x 360 mm - Gantry passage: 3.000 - Height below vertical spindle: 1.400 mm - Working clamping width: 2.500 mm - Fixed table dimensions: 5.000 x 2.500 mm - Longitudinal pallet system EQUIPMENT: - Tool changer (chain magazine): 80-positions - Cooling through the spindle centre - 2 chip conveyors - Gantry panelling - Touch probe, Brand: RENISHAW - Electronic hand wheel - Remote diagnosis - Tool management and wear management - CE marking Electrical connection values: - Total power requirement: 130 kVA - External dimensions of the machine: 22,6 x 8,0 x 6,3 m There is no guarantee for correctness and completeness of the technical details and accessoires. - Subject to prior sale - Detailed technical data sheet and information on equipment available on request.

Condition: ready for operation (used), Year of construction: 1970, functionality: fully functional, machine/vehicle number: 50052, Year of manufacture: 1970 Serial number: 50 052 The machine was overhauled in 2007. GENERAL CHARACTERISTICS OF THE MACHINE The machine features a fixed gantry with a moving table. The gantry is equipped with a height-adjustable crossbeam, which can be fitted with one or two vertical spindles in the VF 120 version. The gantry can also be fitted with one or two side-mounted (horizontal) VF 160 headstocks. The clamping surface consists of two interconnected clamping tables, which can also be used individually when disconnected (only one table can be operated at a time). Clamping Table: Dimensions of one table: 1,600 x 3,000 mm Total length of connected tables: 7,000 mm Nodpoxxwy Aefx Ac Dslh Clamping surface of connected tables: 6,500 mm Clamping T-slots (width x pitch x number): 28 mm x 160 mm x 9 pcs Table height from base: 900 mm Travel of one table: 3,000 mm (connected tables: 6,500 mm) Table feed rate: 20 – 2,000 mm/min Rapid traverse: 4,000 mm/min Gantry with height-adjustable crossbeam: Clearance between side columns: 2,020 mm Crossbeam height adjustment: 110 - 1,685 mm Crossbeam feed rate: 1,450 mm/min VF 160 Horizontal Headstock: Taper: ISO 60 Motor power: 30 kW Speed range: 15 – 710 rpm Feed rate: 10 – 2,000 mm/min Number of speeds: 16 VF 120 Vertical Headstock: Taper: ISO 50 Motor power: 18 kW Speed range: 28 – 910 rpm Number of speeds: 16 Overall machine dimensions (L x W x H): 14,780 mm x 5,650 mm x 4,800 mm

Condition: used, Year of construction: 2002, machine/vehicle number: 6243, travel distance X-axis: 5,000 mm, travel distance Y-axis: 2,100 mm, travel distance Z-axis: 1,500 mm, Equipment: documentation/manual, Base machine / travel ranges: X-axis machine stand 5,000 mm, Y-axis spindle head slide 2,100 mm, Z-axis spindle head 1,500 mm. Machine stand: Compact, torsion-resistant welded construction with hardened flat guide rails and telescopic steel covers to protect against chips and coolant. Spindle head slide: Cast iron design with hydraulic weight compensation, guided by combined roller/plain bearing guides. Machine bed: Flat bed design with approximately 1,200 mm guide rail width and roller compact guides for high precision. Automatic universal milling head: CNC-swiveling milling head arbor 340 x 1°, Hirth gearing approximately 125 kN; milling head 180 x 1°, approximately 100 kN; milling spindle with hydromechanical tool quick-change system, clamping force approximately 25 kN; tool holder SK 50, DIN 69871. Main drive: 37 kW at 100% ED, 53 kW at 40% ED; externally ventilated AC motor, 2-stage gearbox with automatic changeover; speed 22–4,000 1/min. Feed drives: Digital AC individual drives; X/Y: 2–12,000 mm/min, Z: 2–15,000 mm/min. Control system / measuring systems: Central operation via Heidenhain TNC 430 M. Direct, non-contact linear measuring systems. Optional: Heidenhain iTNC 530. Electrical system: EN 60204 / VBG 4, 400/230 V ±10%, 3 phases, 50 Hz, 24 V control voltage; connected load approximately 80 kVA. Control cabinet IP54, main motor IP55. Lubrication: Main gearbox / milling head drive oil circulation lubrication; main spindle grease long-life lubrication; guides / ball screws pulse central lubrication. Coolant: Internal / external coolant supply with paper band filter. Max. 50 l/min at 10 bar or 47 l/min at 16 bar; tank 500 l. Coolant / air changeover. Oil cooler for temperature stabilization and increased manufacturing accuracy. Leveling system: Electromechanical, via 2 vertical ball screws with separate drives, measuring systems, and CNC axes. Working platform: Moves in the X direction, with CNC control panel; electrically secured door with viewing window. Pick-up station: Njdpfx Ajz Dvycec Dslh 10 tools; max. tool weight 25 kg, length 400 mm, Ø 125 mm, with free adjacent slots Ø 250 mm. Clamping plate: 3,500 x 3,000 mm; T-slots 22 H12 DIN 650, spacing 250 mm; clamping surface accuracy class 1 DIN 876. CNC rotary table: Clamping surface 1,250 x 1,600 mm / Ø 1,800 mm; Hirth division 360 x 1°; 6 longitudinal slots 22 H12, 2 positioning slots 22 H7; T-slot spacing 160 mm; centering bushing Ø100 H7 x 20 mm; max. 5 1/min; tilting moment 85,000 Nm; tangential moment 120,000 Nm; table load max. 11,500 kg. Additional equipment: Oriented spindle holder 360 x 1°; hinged band chip conveyor for X=5,000 mm, feed width approximately 350 mm, discharge height approximately 1,250 mm; 3D touch probe; electronic handwheel HR 410 for 3 axes; pendulum machining for 2 work areas with monitored safety areas; manually adjustable splash guard. Collision monitoring: Brankamp CMS with piezoelectric strain gauge; if the process limit is exceeded, the axes are braked and the machine is switched off. Painting: Machine / control cabinet RAL 7035, milling head / spindle head RAL 5021; DD structured paint, semi-gloss, oil and alkali resistant. Power connection: 400 V, 3 phases, 50 Hz, 80 kVA, 160 A slow-blow; compressed air 4–6 bar, connection G 1/4. CE-relevant environmental protection to be provided on-site; adapter plates for chip / coolant return are not included. Coordinate information: Y 730.0124. Documentation: Operating manual SHW-UF6L and Heidenhain TNC

Condition: used, Year of construction: 2001, x-travel 8000 mm Nodpeyqt Izjfx Ac Djlh y-travel 1000 mm z-travel 1250 mm dividing head CNC control Fagor type 8025 CNC clamping plate 1500x3000 mm clamping plate 1500x4000 mm clamping plate 1500x4000 mm 4-axis controlled sub-machine Handwheel The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: excellent (used), Year of construction: 2010, operating hours: 9,416 h, functionality: fully functional, feed length X-axis: 535 mm, feed rate Z-axis: 3,845 m/min, turning diameter over cross slide: 630 mm, turning diameter: 950 mm, turning diameter over top slide: 630 mm, spindle bore: 254 mm, spindle speed (max.): 630 rpm, total height: 1,850 mm, total width: 2,105 mm, Hankook Protec 9NC Hollow Spindle Oil Country Lathe Model: Protec 9NC Nledpfxez S Nc Uj Ac Djh Control: Fanuc 21i-TB Year: 2010 Spindle Bore: 254mm Capacity: 950 x 4000mm Swing Over Cross Slide: 630mm Spindle Speeds: To 630 RPM (2 Ranges) Main Motor: 37 KW Machine With: Double 4 Jaw Manual Chucks (front or rear) Duplomatic 8 Station Turret 2 x Fixed Steadies

Condition: used, Year of construction: 2002, x-travel 16300 mm y-travel 2600 mm z-travel 1600 mm Control Heidenhain type TNC 430 tool taper ISO 50 spindle turning speed range 22-4000 U/min feed in x - axis 36000 mm/min feed in y - axis 24000 mm/min feed range Z-direction 24000 mm/min main drive motor 37 kW Tool changer 90 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. Nlodpfxsyq Swus Ac Dsh We look forward to your visit. Your Markus Hirsch Team