Wood chip and pellet boiler – 45–150 kW

KWB Powerfire TDS 150

Year of construction: 2005, condition: ready for operation (used), A Sodick CNC wire EDM machine is available. Travel X/Y/Z: 750mm/500mm/400mm, travel U/V: 770mm/520mm, max. workpiece dimensions X/Y/Z: 1050mm/750mm/400mm, max. workpiece weight: 1500kg, wire diameter range: 0.15mm-0.3mm. Machine dimensions X/Y/Z: approx. 2100mm/2800mm/2350mm, weight: approx. 5300kg. Documentation available. An on-site inspection is possible. Dsdpezi Ei Hefx Acpewd

Year of construction: 1985, condition: ready for operation (used), Travel X/Y/Z: 1300mm/900mm/1000mm, table dimensions X/Y: 2000mm/750mm, max. table load: 5000kg, rapid traverse: 6m/min. Machine dimensions X/Y/Z: approx. 3650mm/2700mm/2700mm, weight: approx. 9000kg, control: Heidenhain TNC 150. Documentation available. An on-site inspection is possible. Dedow Duuqspfx Acpjwd

Condition: good (used), total length: 6,000 mm, total width: 1,650 mm, plate height: 300 mm, Manufacturer: STOLLE Type: CAST IRON... Year of construction: 2004 Specifications Metric US Standard Length 6000 mm Width 1650 mm Height 300 mm Number of T-slots 6 Distance between T-slots / spacing 250 mm T-slot size 27 mm Weight per plate approx. Djdpfxjwpva Es Acpewd 7200 ton Number of matching pieces 4 Dimensions (estimated) Length 6000 mm Width 1650 mm Height 300 mm Weight 7200 kg Please note: The information on this page has been obtained to the best of our knowledge and, where possible, from the manufacturer. The information is provided in good faith, but the accuracy cannot be guaranteed. Accordingly, you will not be given any representation or contract terms. We recommend that you verify all important details.

Condition: refurbished (used), Year of construction: 2011, functionality: fully functional, workpiece weight (max.): 3,000 kg, travel distance X-axis: 800 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 510 mm, total height: 2,875 mm, total length: 2,870 mm, total width: 2,670 mm, workpiece height (max.): 510 mm, workpiece width (max.): 900 mm, workpiece length (max.): 1,450 mm, overall weight: 6,300 kg, GF AgieCharmilles CUT 400 Year of manufacture: 2011 Control system: Charmilles Millenium Dwedpfx Ajzhlvkscpsd Travel ranges (X / Y / Z): 800 x 550 x 510 mm Travel ranges (U / V): 800 x 550 mm Max. conical angle: +/- 30° at a height of 510 mm Integrated Collision Protection (ICP) on all 5 axes Maximum workpiece dimensions: 1450 x 900 x 510 mm Maximum workpiece weight: 3000 kg Cutting speed of 400 mm²/min Best surface finish: Ra 0.2 µm Available wire diameters: 0.20 mm to 0.30 mm Includes option for a large wire spool with 25 kg (K250) Dimensions of the complete system: 2670 x 2870 x 2645 mm Total weight of the system: 6300 kg The machine will be cleaned, completely overhauled, and tested for all functions after order receipt. Optional: - Commissioning of the machine at your location - On-site training - Cooling unit - Transportation - Clamping device set

Condition: used, operating hours: 30,374 h, functionality: fully functional, machine/vehicle number: 000-0059085/3, overall weight: 997 kg, volume flow: 209 m³/h, power: 113.9 kW (154.86 HP), heating capacity: 99 kW (134.60 HP), smoke pipe connection diameter: 200 mm, nominal heat output: 113.9 kW (154.86 HP), space requirement length: 3,140 mm, space requirement height: 2,400 mm, space requirement width: 2,170 mm, temperature: 90 °C, total height: 2,310 mm, total length: 2,040 mm, total width: 860 mm, type of input current: three-phase, exhaust gas temperature (max.): 160 °C, input voltage: 400 V, negative pressure: 15 Pa, nominal power: 99 kW (134.60 HP), tank capacity: 10 l, input current: 13 A, operating pressure: 3 bar, Equipment: documentation/manual, hot water, KWB UNIT USV100 / Multifire – 99 kW biomass boiler Used Austrian boiler with KWB Comfort 3 controls, output modulation, lambda and negative-pressure control, automatic heat exchanger cleaning and ash extraction. Technical data: - Nominal heat output: 99 kW - Minimum output: 27.6 kW - Fuel input: 113.9 kW - Water capacity: 167 litres - Maximum operating pressure: 3.5 bar - Maximum temperature: 90 degrees C - Weight: approximately 997 kg - Flue connection: 200 mm Dwedpfezhh Iisx Acpjd - Operating hours: 30374 h Data plate specifies 6 mm wood pellets. Wood chip operation depends on the installed extraction and conveying equipment. Exact equipment and scope of delivery by arrangement. Located in Mosonmagyaróvár, Hungary. Inspection by appointment. Transport, installation and commissioning by the buyer.

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, Description WE SELL AN VERY GOOD CONDITION 5 AXIS FANUC ROBOCUT YEAR 2015 Machine will come with full tools and full equipment and amm cutting material from stock ready to work, ITS WORKING STILL IN THE TOOL WORKSHOP. The FANUC ROBOCUT ALPHA C600IA wire EDM machine was manufactured in 2015 in Japan. It is a modern Japanese electro erosion wire cutter. The Fanuc Robocut cutter is adapted to the processing of various machine parts, e.g. dies, dies, punches, as well as parts with complex, complicated shapes and materials that are difficult to cut. This model was made to order and, unlike the standard model, has a travel of 410 mm in the Z axis. The new Robocat Alpha C600IA wire cutter currently costs approx 150,000 Euro net from the manufacturer. The cutter presented here was used sporadically in the tool shop for the production of prototypes and is in very good technical condition CONTROL: FANUC series 31i-W MODEL B 5 AXIS WORKING RANGE: X : 600 mm / 900mm/min Y: 400 mm / 900mm/min U: 200 mm / 450mm/min V: 200 mm / 450mm/min Z: 310 mm / 450mm/min MAX WORPIECE WEIGHT: 1000 KG MAX WORKPIECE DIMENSIONS: 1050 x 820 x 400 mm MACHINE POWER SUPLY: 13KVA FREQUENCY: 50 / 60 Hz MACHINE WEIGHT: 3000 KG Djdpfxsydr Ads Acpjwd MACHINE WILL BE WORKING TILL MIDLLE FEBRUARY AND WILL BE RELEASED FROM THE PRODUCTION FOR CUSTOMER WE ORGANIZE DISMANTLING SECURING AND LOADING. ALSO WE CAN OFFER TRANSPORT WORLDWIDE