Shredeer for plastic 45kw

Year of construction: 2003, operating hours: 10,600 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 6094, Equipment: centralized greasing system, Spare parts donor! TECHNICAL DETAILS Coarse screen deck: 120/150 Fine screen deck: 10/25 Kdjdpfxoyzznls Afdsk MACHINE DETAILS Generator voltage: 400 V / 50 Hz Weight: 20,000 kg Engine operating hours: approx. 10,600 h EQUIPMENT Trailer Hopper Magnetic drum for mid-size fraction conveyor Magnetic drum for oversize fraction conveyor Clip-on chute Hydraulic rear support Direct connection Central lubrication system Generator 50 mm drawbar eye Note: The engine starts but shuts off again after a while. Presumably there is a fuel issue. The generator produces power. The machine is currently not roadworthy as it has been stationary for a long time. Road registration is currently not possible.

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C Kedpfx Afowp Rqfjdsdk • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, cutting range round steel at 90°: 400 mm, cutting length (max.): 760 mm, working height: 720 mm, saw band length: 5,920 mm, TECHNICAL DETAILS Saw band dimensions: 5,920 x 41 x 1.3 mm Cutting speed: steplessly adjustable (1:7) Working range (round): max. 400 mm Working range (square): 400 x 370 mm Cutting length (single stroke): 10 - 760 mm Cutting length (multiple strokes): max. 9,999.9 mm Working height: 720 mm Clamping force: 3,600 N Minimum finished part length: 10 mm (35 mm vertical) Kjdpfx Asyzn Hbjfdedk Note: Dismantling and loading can be offered by the seller at an additional cost. Roller conveyor is not included.

Condition: ready for operation (used), Year of construction: 2007, operating hours: 19,357 h, functionality: fully functional, spindle speed (max.): 12,000 rpm, travel distance X-axis: 800 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 510 mm, controller model: Fanuc Series 31i-Model A5, TECHNICAL DETAILS X-axis travel: 800 mm Y-axis travel: 520 mm Z-axis travel: 510 mm Milling spindle: 12,000 rpm Tool holder: Capto C6 Rapid traverse: 60 m/min MACHINE DETAILS Kdsdpfxoyw I Htj Afdek Control: Fanuc Series 31i-Model A5 Chain tool magazine: 48 positions Additional magazine: 90 positions Operating hours Total operating hours: approx. 48,974 h Machining time: 19,357 h EQUIPMENT Coolant system Chip conveyor Note: Clara extraction unit is not included in the scope of delivery.

Condition: excellent (used), Year of construction: 2003, working width: 215 mm, welding power (max.): 750 kVA, Complete Mesh welding/Lattice girder factory Kdodpfx Afsqy Ek Asdsk Factory consists : - Mesh welding line SCHLATTER PG 24 , Semi- automatic , Year - 2002 - Lattice Girder Line SMEI , Full automatic , Year - 2003 - Straightening and cutting machines 1x Wafios R4 2 x VITARI NR16 1X VITARI NR10 - Cold drawing line SMEI , Input wire max.10mm, Speed - 4m/sec. - But welding achine SMEI - Wire sharpener SMEI

Condition: not inspected (used), Year of construction: 2000, operating hours: 8,523 h, functionality: unexamined, travel distance X-axis: 1,000 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 500 mm, spindle speed (max.): 10,000 rpm, number of slots in tool magazine: 22, No reserve price – guaranteed sale to the highest bidder! Kodpfx Afoyn Nwtsdsdk Bidding obligates the buyer to collect the machine on time, either between 11.05.2026 and 13.05.2026 or between 18.05.2026 and 21.05.2026! TECHNICAL DETAILS Travel distance X: 1,000 mm Travel distance Y: 500 mm Travel distance Z: 500 mm Table dimensions: 1,150 x 490 mm Number of tool positions in the magazine: 22 Spindle taper: SK 40 (DIN 69871-A40) Max. spindle speed: 10,000 rpm MACHINE DETAILS Control: HEIDENHAIN TNC 426 Dimensions & Weight Dimensions (L x W x H): 4,500 x 3,500 x 2,700 mm Weight: 4,200 kg Operating Hours Automatic operation: 8,523 h Control on-time: 71,860 h EQUIPMENT Technical documentation Spare parts (as shown in the pictures) Note: Only a 7.5t truck can turn around on the company premises. It is recommended to send a smaller truck for collection.

Condition: not inspected (used), Year of construction: 2001, functionality: unexamined, machine/vehicle number: 822441, travel distance X-axis: 1,020 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 600 mm, controller model: HEIDENHAIN TNC 410 PA, spindle speed (max.): 6,000 rpm, No reserve price - guaranteed sale to the highest bidder! By placing a bid, you are obliged to collect the item on time, either between 11.05.2026 and 13.05.2026 or between 18.05.2026 and 21.05.2026! TECHNICAL DETAILS Travel distances Travel X: 1,020 mm Travel Y: 510 mm Travel Z: 600 mm Spindle speed range: 40–6,000 rpm Drive power: 13 kW Spindle taper: BT 40 Number of tool stations in the tool changer: 22 Rapid traverse X and Y axes: 40 m/min Rapid traverse Z axis: 30 m/min Ksdpfeyn Nvvjx Afdodk Work table Length: 1,150 mm Width: 490 mm MACHINE DETAILS Control system: HEIDENHAIN TNC 410 PA Dimensions & Weight Dimensions (L x W x H): 2,800 x 2,400 x 2,400 mm Weight: 4,800 kg EQUIPMENT 3D probe Note: The machine vices mounted on the work table and the tool holders, including the tools installed in the tool magazine and spindle, are not included in the scope of sale and delivery. The oil mist extractor, which may be visible in the photos, is also not included in the scope of sale and delivery.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. Kdedpfx Afefz U S Esdok All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Condition: not inspected (used), functionality: unexamined, No minimum price – guaranteed sale to the highest bidder! Bidding commits you to timely collection, either between 11/05/2026 and 13/05/2026 or between 18/05/2026 and 21/05/2026! TECHNICAL DETAILS Contents: - Mounted vice (jaw width: 150 mm) - Belt sander (Manufacturer: FERM, belt width: 100 mm, disc diameter: 150 mm) - Clamping jaws - Dies - Tap sets MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 3000 x 1100 x 1200 mm Weight: 350 kg Note: The sale does not include the drill press or tapping arm currently on the workbench. External reference: Pieper – Lot 67 Kdsdpfx Afjyn Ibwsdok

Condition: not inspected (used), functionality: unexamined, throat depth: 1,200 mm, machine/vehicle number: 94023588, No minimum price – guaranteed sale to the highest bidder! Kdsdpfjyn H Rdsx Afdok Placing a bid obligates you to collect the item on time, either between 11.05.2026 and 13.05.2026 or between 18.05.2026 and 21.05.2026! TECHNICAL DETAILS Reach: 1200 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 1200 x 1000 x 700 mm Machine weight: 80 kg External reference: Pieper - Lot 68

Condition: ready for operation (used), Year of construction: 2002, There are zwei identical vertical bag filling machines available, weight: 1.1t. Kdjdpfx Asnfvxzjfdjk

Condition: not inspected (used), functionality: unexamined, plate length: 630 mm, plate width: 630 mm, No reserve price – guaranteed sale to the highest bidder! Kdjdpoyn H Hljfx Afdek Placing a bid obligates you to collect the item on time, either between 11.05.2026 and 13.05.2026 or between 18.05.2026 and 21.05.2026! TECHNICAL DETAILS Plate dimensions: 630 mm x 630 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 630 x 630 x 950 mm Weight: 150 kg External reference: Pieper - Lot 75

Condition: not inspected (used), functionality: unexamined, plate length: 630 mm, plate width: 630 mm, No minimum price – guaranteed sale to the highest bidder! Placing a bid obligates you to timely collection either between 11/05/2026 and 13/05/2026 or between 18/05/2026 and 21/05/2026! TECHNICAL DETAILS Plate dimensions: 630 mm x 630 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 630 x 630 x 920 mm Weight: 100 kg External reference: Pieper - Lot 103 Kdjdpfxjyn Hwqs Afdsk

Condition: ready for operation (used), Including Ascending Conveyor SBM 45 and Counting Machine ZMR 3/ 3-130. Kjdpfx Aehncwisfdsdk

Condition: not inspected (used), functionality: unexamined, No minimum price – guaranteed sale to the highest bidder! Submitting a bid obligates you to collect within the specified period, either between 11.05.2026 and 13.05.2026 or between 18.05.2026 and 21.05.2026! TECHNICAL DETAILS Available in different sizes MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 800 x 600 x 50 mm Weight: 30 kg Kedsyn Hq Repfx Afdodk External reference: Pieper - Lot 125