Used Weingarten Automatic Punching Press - Double Column for sale (45,025)

Condition: as good as new (ex-display), Year of construction: 2023, pressing force: 120 t, table length: 600 mm, table width: 600 mm, Here are the technical data of the offered machine: Technical data + information: HB 2021-A-188, oil hydraulic double column press 120 T bottom piston heating press. - idle speed up to 40 mm/sec - Opening speed up to 40 mm/sec - Starting press speed 5-15 mm/sec - Table size/heating plate size 600 × 600 mm - ram size/heating plate size 600 × 600 mm - 2 heating plates, electrically heated, up to 250 degrees - as OPTION - total size approx. 2000 × 1000 × 2800 mm height - Oil temperature control - Automatic lubrication - Free positioning of the ram - SICK/LEUTZE light barriers 14,1 mm on front side - Circuit oil cooling - Pressure holding valve 0 to 1800 sec. - Rear monitored door - Pressure adjustment from 30 T to 120 T - Travel limitation either by pressure or position - Programming set-up mode, single stroke (adjustable via rotary switch) - Control panel permanently installed in cabinet wall - Two-hand operation - Machine body double painted - Signal light: red: alarm, yellow baking phase, green: ready - Heating plates with electric heating rods, up to max. 250 degrees - Assembly, commissioning, instruction against separate charge Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 1,600 kN Free ripping force max. 200 kN Pressure build-up time closed die steel to steel Max. 8 sec. Dimensions Max. Opening width per compartment 200 mm Stroke and min. opening per compartment 400/200 mm Table height above floor, without heating pl. 850 mm Height above floor (overall height) approx. 2.800 mm Hall height min. 3,500 mm Parallel deviation at 20 °C +/- 0.1 mm Deflection Determined at max. clamping force with 70 % occupancy ≤ 0.2 mm/m Total weight of the press without operating materials approx. 9 to Accessories: 4 HEATING PLATES 500 × 400 mm, max. heating capacity Equipped with temperature sensor 300 degrees Speeds Fast closing with 15 mm sec. Pressing speed 10 mm sec. Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 8 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 240 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH gear pump approx. 48 L/min Oil volume approx. HLP 46 MW 300 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Automatic pressure readjustment after 5 % pressure loss Pressure stabilization for up to 1800 sec. Ksdpfx Aek S Dt Tjg Aodu Electrical system Main supply 400 V AC Control voltage Hydraulic pumps 24 V DC 24 V DC Frequency 50 Hz Connection hydraulic main motor 15 kW Total connection approx. without heating plates 19 kW ##### If the press does not exactly meet your requirements, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Our great strength is special machine construction and press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Condition: used, Single-Column Eccentric Press RASTER ZEULENRODA Type PDA 100 Year of manufacture: 1995 Pressing force: 100 tons Throat depth: approx. 360 mm Table size: 1200 x 710 mm Ram area: 900 x 500 mm Table opening: 400 x 120 mm Stroke adjustment: 6 to 82 mm Ram adjustment: 100 mm Installation height, max. stroke, ram Top Dead Center (TDC): max. 469 mm Installation height, max. stroke, ram Bottom Dead Center (BDC): max. 387 mm Strokes per minute: 50-200 s.p.m. Main drive motor power: 18.5 kW Power supply: 400 Volt, 50 Hz - Hydraulically actuated multiple-disc wet clutch and spring-loaded safety brake - Infinitely variable drive via PIV gearbox with inching mode for automatic stroke adjustment and setup operations - Hydraulic overload protection in the ram - Press force and process monitoring via UNIDOR APS - Pneumatic, steplessly adjustable ram weight compensation - Roller feeder MABU WE16, 160 x 3 mm, programmable feed length - Central grease lubrication - Operating manual and documentation for the press Included: Roller feed unit MABU Type WE16 Ksdpfsx U Eiasx Ag Aedu Strip width: 160 mm Strip thickness: max. 3 mm Strip cross-section: max. 300 mm² Roller diameter: 63 mm Strip speed: 40 m/min - Adjacent feeder control MABU Space requirements for eccentric press L x W x H: 270 x 240 x 350 cm Weight of the press: 13.5 tons

Year of construction: 1992, condition: ready for operation (used), Max. ram force: 1600kN, length: 3170mm, width: 2500mm, height: 5080mm, weight: 23t, with documentation. Kdedpfxslc N Rys Ag Aeu

Condition: ready for operation (used), Two mechanical large-format double-column eccentric punching presses Rhodes (UK) are available. Press force: 350t, table dimensions X/Y: 1750mm/920mm, ram dimensions X/Y: 1550mm/615mm, ram stroke: 101mm, ram adjustment: 100mm, stroke rate: 50 strokes/min, max. installation height: 483mm, side opening X/Y: 630mm/380mm, table height: 933mm, weight: approx. 43000kg. Documentation available. On-site inspection is possible. Ksdpeyfv I Tsfx Ag Ajdu

Year of construction: 1997, condition: excellent (used), functionality: fully functional, machine/vehicle number: 697/2, Equipment: 4th hydraulic function, Hounsell Engineering 50 Tonne 4-Column Hydraulic Press – 1997 We are pleased to offer this Hounsell Engineering Ltd (UK) 50-tonne 4-column hydraulic press, manufactured in 1997. A substantial, British-built industrial hydraulic press with heavy-duty construction, previously used in a production environment and now available for sale due to surplus requirements. Suitable for a wide range of pressing, forming, assembly, fabrication, maintenance and general engineering applications. Machine specification: Kdjdpfsz Ib R Isx Ag Aou Manufacturer: Hounsell Engineering Ltd, UK Type: 4-Column Hydraulic Press Rated capacity: 50 tonnes Year of manufacture: 1997 Machine / Serial No.: 697/2 Stroke: 200 mm System pressure: 250 bar Pump motor: 5.5 kW Electrical supply: 415 V Control voltage: 110 V Hydraulic fluid: Texaco HD 32 Construction: Heavy-duty industrial steel Condition: Very good used condition The press was in service prior to removal and is being offered for sale as surplus equipment. With a rated capacity of 50 tonnes, the machine is capable of generating approximately 500 kN of compressive force, making it suitable for a broad range of industrial and workshop applications. Condition & Inspection The machine is offered in good used condition. Prospective purchasers are welcome and encouraged to inspect the press before purchase to satisfy themselves as to its condition, specification and suitability for their intended application. Sold as seen. No warranty is given or implied. Collection & Loading Location: Kent, England, UK Collection only due to the size and weight of the machine. Loading assistance may be available by prior arrangement. Further photographs and information can be provided, including serial plate details, overall dimensions, weight and loading arrangements. A good opportunity to acquire a substantial 50-tonne industrial hydraulic press at considerably below the cost of a comparable new machine. Please contact via the links within for further details, photographs, or to arrange an inspection. Many Thanks, Search terms: Hounsell Hydraulic Press, 50 Tonne Press, 4 Column Press, Hydraulic Workshop Press, Industrial Press, Engineering Machinery, Pressing Machine, Forming Press, Manufacturing Equipment, Fabrication Machinery.

Condition: used, Pressure total: 800 ton Ram stroke: 700 mm Slide adjustment: 500 mm Shut height (stroke down, adjustment up): 1350 mm Free frontal opening L-R: 3550 mm Table surface area : 3500 x 2000 mm Slide area: 3500 x 2000 mm Die cushion capacity in table: 150 ton Die cushion stroke: 200 mm Die cushion pad area: 2700 x 1500 mm Number of strokes: 7 - 21 s.p.m. Ejector in ram: 60 ton Ejector stroke in ram: 150 mm Required power: kW Height over floor approx.: 8600 mm Ksdpfx Agsz Hi Rgs Ajdu Weight of machine approx.: 250 ton Standard configuration LINK DRIVE

Year of construction: 1974, condition: used, Offered are two Weingarten single-column eccentric presses. 1) Weingarten AR 125 single-column eccentric press, delivered: 1970, pressing force: 125t, max. sheet thickness: 13mm, stroke rate: 44/66strokes/min, ram stroke: 20-120mm, ram adjustment: 100mm. 2) Weingarten AR 125 single-column eccentric press, delivered: 1974, pressing force: 125t, stroke rate: 42/62strokes/min, ram stroke: 20-120mm, ram adjustment: 100mm. Inspection possible by arrangement. Kdedpoz S Iupsfx Ag Aou

Condition: used, Single-column – Eccentric press PELS - RICHTER, type PEKR 125 Machine no. 20684, year of manufacture 1967 Pressing force: 125 tons Reach: 430 mm Table size: 1100 x 750 mm Ram surface: 890 x 650 mm Table opening: Ø 400 mm Stroke adjustment: 6 to 115 mm Ram adjustment: 100 mm Installation height for maximum stroke at the top: max. 450 mm Kedpfxefim Thj Ag Asdu Arbor hole: Ø 50 mm Stroke rate: 60 strokes/min Table height above floor: 900 mm Motor power: 7.5 kW Power connection: 380 volts, 50 Hz - Overload protection by shear plate in the ram - Compressed air coupling-brake combination DESCH - Ram weight balancing cylinder - Manual ram adjustment - Two-hand operation - Cam indexing mechanism - Central grease lubrication system Vögele - Stroke counter Space requirement L x W x H: 2300 x 1450 x 3030 mm Weight: approx. 10 tons Good condition

Condition: used, Year of construction: 1990, pressure 500 t distance between columns 1220 mm stroke 600 mm distance table/ram, max. stroke up, adjustment up 1000 mm table surface area 1600 x 1200 mm pressure of drawing cushion in table 320 t stroke of drawing cushion in table 150 mm drawing cushion surface in table 750 x 625 mm pressure of drawing cushion in ram 180 t stroke of drawing cushion in ram 100 mm drawing cushion area in ram 750 x 625 mm ram surface 1600 x 1200 mm table height over floor 800 mm speed down 665 mm/s speed up 530 mm/s Kdjdpfx Agezrpqts Aju working speed 34 - 100 mm/s quantity of oil 2000 l power requirement 180,0 kW weight 40,0 t Dimensions (WxDxH) 3,2 x 2,4 x 7,5 m Depth of foundation pit 4,1 m Height above floor 5,55 m YOM 1975 - Overhaul 1990 with oil-hydraulic drive, hydraulic drawing cushion in table and ram

Condition: used, Year of construction: 2002, machine/vehicle number: 10857, Pressure total: 315 ton Stroke: 1100 mm Daylight: 2200 mm Table surface area : 2500 x 1000 mm Slide area: 2500 x 1000 mm Die weight at the ram max.: 6000 kg Approach speed: 600 mm / sec Kedpfxevmfzbj Ag Aedu Working speed: 32 - 230 mm / sec Return speed: 600 mm / sec Required power: 158 kW Weight of machine approx.: 44 ton Height over floor approx.: 6175 mm Automation

Condition: like new (used), Year of construction: 2019, pressing force: 400 t, pressure:400 t Kdjdpfx Aofh Izmjg Aeu stroke:900 mm Table dimensions:1200 x 1200 mm Deep-Drawing Pillow:150 t travel away deep-drawing pillow:280 mm Daylight Opening:1100 mm

Condition: used, Double-column Hydraulic Press SCHÖN Type SH 25 Machine No. 2440 Year of manufacture: 1979 Press force: 25 tons Column spacing: 630 mm Lateral passage between columns: 120 mm Table area: 580 x 320 mm Ram area: 360 x 220 mm Clamping pin hole: Ø 40 mm Maximum ram stroke: 100 mm Maximum installation height: 270 mm Kedpfx Agjyz Dr To Asdu Table height above floor: 900 mm Motor power: 7.5 kW Power supply: 380 Volt, 50 Hz - Main cylinder overhauled in 2025 - SICK LUV 206 safety light curtain - Two-hand control - Stroke counter - Rapid stroke and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Press force regulation - Press time extension 1–10 s (pressure holding time) - No operating manual and no wiring diagrams Required space (L x W x H): 1450 x 1100 x 2200 mm Weight: 1200 kg In good condition

Condition: used, Year of construction: 1977, Pressure total: 800 ton Ram stroke: 700 mm Slide adjustment: 600 mm Shut height (stroke down, adjustment up): 1500 mm Free frontal opening L-R: 3800 mm Free lateral opening F-B: 1450 x 1100 mm Table surface area : 3500 x 1900 mm Slide area: 3500 x 1900 mm Die cushion capacity in table: 150 ton Die cushion stroke: 250 mm Die cushion pad area: 2780 x 1570 mm Number of strokes: 7 - 18 s.p.m. Required power: 120 kW Kedpfxoyxmuls Ag Asdu Height over floor approx.: 9510 mm Weight of machine approx.: 260 ton

Condition: used, Year of construction: 1993, pressure 630 KN distance between columns 800 mm Kdjdoyutwkspfx Ag Aou stroke 150 mm table surface area 720x550 mm ram surface 720x520 mm dayligth 420 mm rapid drop speed 394 mm/sec working feed 71/17 mm/sec return speed 390 mm/sec adjustment movement of the stroke 120 mm total power requirement 15 kW Cutting impact dampening The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Double-column hydraulic press SCHÖN Type SH 25 Kdsdpow A Amrjfx Ag Aou Machine no.: 4453 Year of manufacture: 1999 Pressing force: 25 tons Column width: 500 mm Lateral column clearance: 120 mm Table surface: 440 x 320 mm Table opening: Ø 175 mm Ram surface: 360 x 220 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 100 mm Max. installation height: 270 mm Table height above floor: 900 mm Motor power: 7.5 kW Connection voltage: 380 V, 50 Hz Equipment: - Safety light curtain SICK, type FGS 300-11 - Two-hand operation - Stroke counter - Rapid and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Pressing force regulation - Adjustable pressing time 1–10 s (pressure holding time) - Adjustable return stroke speed - Blow-off device electrically pre-wired, without air valve - Manual hydraulic tool safety, adjustable via handwheel Dimensions (L x W x H): 1300 x 1200 x 2200 mm Weight: approx. 1200 kg Good condition

Condition: excellent (used), Year of construction: 2016, Specifications Manufacturer: IMV Model: DM125 Year: 2016 Condition: Used Stock number: 0396 Ram force: 1,250 t Number of press points: 2 Drive: Eccentric with stroke adjustment Ram stroke: 250–400 mm Strokes/min: 5–35 Vertical daylight below bolster, CBRA: 1,150 mm Table dimensions: 4,500 x 2,000 mm Ram dimensions: 4,500 x 2,000 mm Side column window: 2,600 mm Kdedpfxoyw Uf Ae Ag Aou Max. front column window: 4,900 mm Transfer cart: 2 units present Main motor power: 290 kW Press weight: 310,000 kg

Condition: excellent (used), Year of construction: 2001, Manufacturer: ROVETTA Model: S4-800 Year: 2001 Condition: Used Stock number: 0392 Builder: Rovetta Slide force: 800 tons Number of driving points: 4 Slide stroke: 700 mm Slide adjustment: 350 mm Strokes per minute: 10-24 Die height (low stroke, high slide adjustment): 1,100 mm Usable distance between front posts: 4,200 mm Bolster table size: 4,000 x 2,000 mm Slide dimensions: 4,000 x 2,000 mm Movable table height: 600 mm Side window size: 3,400 x 1,900 mm Number of cushions: 1 Blankholder cushion - total force: 150 tons Kodpfsyq Tdpsx Ag Asdu Lower blankholder cushion stroke: 250 mm Lower blankholder working area: 1,500 x 1,000 mm.

Condition: used, Year of construction: 1980, Technical details: Kdedju Nfhdepfx Ag Aeu pressure: ca. 100 t distance between columns: 500 mm throat: bis Mitte Stößel / up to center ram: 350 mm dayligth: 450+100 mm min. ram stroke: 26 mm max. ram stroke: 152 mm ram adjustment: möglich/possible mm ram surface area: 550 x 400 mm clamping table: 1020 x 710 mm total power requirement: 10 kW weight of the machine ca.: ca.7 t space requirement approx.:: L:2,0 x B:1,7 x H:3,2 m WITHOUT drawing cushion Can be demonstrated in idle run. i.D. *

Condition: used, Year of construction: 1980, pressure 20 t distance between columns 450 mm stroke 100 mm table surface area 440x320 mm ram surface Ø140 mm hole in the table Ø50 mm table height 900 mm tool hole in ram Ø40 mm total power requirement 3 kW Kdjdovnwd Dopfx Ag Asu weight of the machine ca. 2 t dimensions of the machine ca. BxTxH 1400x1200x2200 mm

Condition: used, Year of construction: 1989, Pressure total: 1400 ton Stroke: 950 mm Daylight: 2000 mm Table surface area : 3600 x 2500 mm Slide area: 3600 x 2500 mm Die cushion capacity in table: 400 ton Die cushion stroke: 500 mm Die cushion pad area: 3060 x 1860 mm Approach speed: 400 mm / sec Kdodjuqdi Uspfx Ag Asu Working speed: 40 / 80 mm / sec Return speed: 400 mm / sec Oil volume: 5000 l Required power: 450 kW Weight of machine approx.: 240 ton Standard configuration with hydraulic tool clamps on the ram

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Complete line as shown on photos. Excellent condition. Ksdpjz D Tdfjfx Ag Aodu Force 200 t Table 1800 x 1000 mm Number of cycles per 1 min Machine dimensions 2700 x 2000 x 4400 mm Machine weight 28000 kg

Condition: excellent (used), Year of construction: 2001, Manufacturer: ROVETTA Model: S4-1500 Link Drive Year: 2001 Condition: Used Stock number: 0391 Manufacturer: Rovetta Number of strokes: 4 Ram force: 1500 tons Ram stroke: 763 mm Kjdpfx Aoyq Tdiog Aedu Ram adjustment: 400 mm Daylight (bottom dead center, ram up): 1,200 mm Distance between front uprights: 5,700 mm Die bed dimensions: 5,500 x 2,500 mm Ram dimensions: 5,500 x 2,500 mm Moving table height: 600 mm Side window size: 3,400 x 1,900 mm Main motor power: 319 kW Blankholder (total force): 150 tons Blankholder stroke: 250 mm Blankholder working area: 2,000 x 1,200 mm Strokes per minute: 8-24

Condition: ready for operation (used), functionality: fully functional, FOR SALE: BRUDERER BSTA 60 High-Speed Stamping Press Kedpfx Agoxz Ugxs Ajdu With Automatic Strip Feeder BBV 300/200 600 kN | 100–800 spm | Fully automatic | Top-tier Swiss quality Technical Highlights: Nominal force: 600 kN Stroke rate: 100–800 strokes per minute Max. feed length: 200 mm. Year: Unknown (No ID Plate) / Tested under power: 2025 Drive power: 30 Hp Control voltage: 24V AC Power connection: 440VAC / 50Hz Adjustable stroke: 20 / 25 / 31 / 38 / 45 /51 / 58 / 64 / 70 / 76 mm Shut/Ram height adjustment: 80 mm Working Dimensions: Max tool installation width: 620 mm Strip pass width: up to 320 mm Ram area: 800 × 500 mm Table area: 620 × 680 mm Max strip width: 300 mm Max feeding pitch: 200 mm Max material thickness: 6 mm Feeding angle: 180 Deg Machine Dimensions: Machine footprint (L × W × H): 2210 × 2075 × 2190 mm Weight (approx.): 8,000 kg Equipment Includes: Feeder BBV 300 – fully synchronized mechanical strip feeder system Integrated control cabinet Pneumatic clutch and brake Adjustable stroke and shut height Compressed air connection: 6–10 bar Oil cooling unit included Ready for integration with peripheral systems Machine in excellent technical and visual condition Fully tested Immediate availability from Europe Worldwide shipping available Contact us today for pricing and further technical details. Let us help you upgrade your production line with Swiss precision engineering.

Condition: used, Year of construction: 1984, pressure 10 t distance between columns 500 mm stroke 200 mm total power requirement 10 kW Kdjdpfx Agst Hwwdj Asu weight of the machine ca. 4.500 kg dimensions of the machine ca. m

Condition: used, Double-column hydraulic press SCHÖN Type UTE/B 50 Machine No. 5509 Year of manufacture: 1971 Pressing force: 50 tons Column span: 550 mm Column clearance (side): 150 mm Table size: 480 x 380 mm T-slot width in machine table: 18 mm Table opening: Ø 70 mm Ram area: 490 x 280 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 150 mm Max. installation height: 390 mm Table height above floor: 890 mm Rapid approach speed: approx. 130 mm/sec Working speed: approx. 20 mm/sec Kedpfxev Srfwj Ag Ajdu Return speed: approx. 130 mm/sec Motor power: 4 kW Power supply: 380 Volt, 50 Hz - Stepless pressing force adjustment - Rapid and working stroke - Pressure or stroke-dependent stroke limitation - Adjustable pressure holding time, press time extension 0.5–6 s - Mechanically adjustable hard stop via handwheel on ram - SICK light barrier, Type LVU - Stroke counter - Double column guide on ram Space requirement (L x W x H): 1100 mm x 1050 mm x 2320 mm Weight: approx. 1.5 tons Good condition