Used Alpha-Pack Gmbh Modell Dedaphs-140S for sale (82,223)

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 530 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible Hsdpfx Anszz Rpceyeu - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Condition: used, Year of construction: 2006, Stamping Press Manufacturer: Schuler Pressen GmbH & Co. KG, Göppingen, Germany Type: SAL 250-1.9 Mark II Serial number: A/260156 (Machine No. 2006-260156) Year of manufacture: 2006 Press force: 2,500 kN (250 tons) Stroke rate: 80–400 strokes/min Hjdpfx Anozil S Ieysu Drive power: 51 kW at 2,000 rpm Ram stroke: 30 mm Ram adjustment: 100 mm Ram lift: 75 mm Installation height (table plate to ram, ram stroke bottom, ram adjustment top): 550 mm Table dimensions: 1,950 x 1,060 mm (as per drawing) Ram face: 1,950 x 800 mm (as per drawing) Compressed air: 5.5 bar Total weight (excl. feed): 48,000 kg Control system: SYS PACO 8000 Sound-insulating enclosure (orange) Strip Feed Unit Manufacturer: Kohler Maschinenbau GmbH, Friesenheim, Germany Type: KRS 18.260/19-2000.2H-BF1 Serial number: 40 871 Year of manufacture: 2006 Connected load: 15.5 kW Supply voltage: 400 V, 50 Hz Decoiler Manufacturer: Kohler Maschinenbau GmbH, Friesenheim, Germany Model: 18 260-1000.2 Serial number: 40 466 Year of manufacture: 1984 Connected load: 8 kW Supply voltage: 380 V, 50 Hz

Condition: as good as new (ex-display), From checkweigher to filling scale Hjdpjhuah Dofx Anyeu The 1-head scale is the most cost-effective solution for semi-automating manual filling processes. With its reproducible accuracy, the filling speed can be significantly increased. Scale features: - Simple operation and cleaning - Low maintenance requirements - Product-contacting parts suitable for food applications (1.4301, NBR) - Operation via a 7" touchscreen - Technical documentation provided by regional partners - Coarse/medium/fine flow control for precise weighing results - Continuously adjustable vibration system - Fully electric operation possible Technical data: - Number of weighing containers: 1 - Volume of weighing container: 4.5 liters - Volume of hopper: 20 liters - Weighing range continuously adjustable between 20 and 3,000 grams - Accuracy: 0.5-3 g, depending on the product - Speed: up to 15 weighings per minute, depending on product, set weight, and desired accuracy - Power: 0.7 kW / 230 V / 50 Hz - Dimensions: 860 mm x 570 mm x 920 mm

Condition: new, capacity up to 600 kg/h power 1,5 (2,0) kW (PS) electric outlet 400V 50Hz (3 phases) fuse 16 A dimensions: length 2 080 mm width 1 030 mm height 1 450 mm insertion resp. discharge height 1 520 mm Hjdsb Nc N Uopfx Anysu weight 295 kg material (frame and juice collection tank) 1.4301 / AISI 304 pressing force 24 to pressing pressure 380 bar juice yield up to 75 % juice discharge connection Ø 30 mm juice discharge height 400 mm suitable for pomaceous and stone fruit scope of delivery: 18 press cloths 80 x 80 cm, 20 press inserts acacia wood 50 x 50 cm

Condition: excellent (used), Year of construction: 2002, machine/vehicle number: Reg Nr. 976, Machine Name: Paddle dryer Used Manufacturer: AVA / Holland Merten GmbH Type: HTK 200 Construction year: 2002 Speed: 107 U/min Pressure range: -1 to 3 bar (drying chamber), 6 bar in the double jacket Material: Stainless steel Driving force: 5,5 KW Model: EExdellCT4 Total content: 235 Liter Hedpfx Aneitcvueyju Parts in contact with product: Stainless steel 1.4571 Gear box: Stirnradgetriebemotor Equipment: Double jacket, mechanical seal, shaft heater Dimensions: L 3400 x W 1100 x H 1500 mm Empty weight: approx. 1600 kg Message: Operating temperature 130°C Design temperature 200°C Internal pressure mixer -1/+3 bar Pressure double jacket +6 bar Accessories: Base frame, Double coat, Mechanical seal, PT100 thermometer, Shaft heating with Maierkopf HWR 225, Sight glass, Technical documentation. Condition: Used very good Price: on request

Condition: used, Year of construction: 2021, functionality: fully functional, machine/vehicle number: 1605269/1, total width: 630 mm, total height: 1,115 mm, total length: 1,010 mm, working width: 460 mm, input voltage: 400 V, type of input current: AC, overall weight: 200 kg, power: 0.37 kW (0.50 HP), roller diameter: 100 mm, passage height: 80 mm, feed rate X-axis: 35 m/min, height adjustment type: mechanical, tank capacity: 2 l, roll width: 450 mm, input frequency: 50 Hz, workpiece height (max.): 80 mm, Equipment: double-sided, For sale is a well-maintained glue and roller application machine from Axel Wirth Maschinen GmbH, type LW 100/450. The machine was manufactured in 2021, has comparatively few operating hours, and is in technically perfect and well-maintained condition. A particular advantage is the adjustable working speed or feed rate (6 - 35 m/min). This allows the machine to be flexibly adapted to different workpieces, materials, and application media. The machine is mounted on a sturdy, mobile base with lockable wheels. As a result, it can be easily moved within the production area and safely positioned at the respective location. A total of two identical machines are available. The stated price applies per machine. An attractive package price is possible if both machines are purchased. The LW 100/450 is suitable for the uniform application of liquid and pasty media onto flat or textured workpieces, for example: - Glue and adhesive - Oil and wax - Stain and primer - Paints and dispersions - Resins and comparable application media Among other materials, wood, solid wood, parquet flooring, chipboard, cork, cardboard, metal, stone, rubber, and insulation materials can be processed. The application quantity can be adjusted via the lateral adjustment devices. The rollers and glue trays can be removed with a few simple steps, making the machine easy to clean. Technical data and equipment Manufacturer: Axel Wirth Maschinen GmbH Type: LW 100/450 Year of manufacture: 2021 Nominal width: 450 mm Working width: approx. 460 mm Passage height: approx. 80 mm Diameter of the application rollers: 100 mm Capacity per glue container: approx. 2.3 liters Drive power: 0.37 kW Adjustable working speed or feed rate Application rollers above and below Separate control cabinet Main switch and emergency stop Mobile base with lockable wheels CE marking Condition: used, well-maintained, and technically perfect Operating hours: comparatively low Inspection and test run are possible after prior appointment. Collection at the Leun location. Shipping by freight forwarder can be organized if required, upon agreement. Hsdjzr H Aaspfx Anyou If you have any questions or are interested, please do not hesitate to contact us. We will be happy to provide further information and photos. Price: €5,900 (negotiable) per machine plus VAT (can be shown). Package price for both machines: on request All information is provided to the best of our knowledge. The sale takes place under the conditions applicable to the seller for used machines.

Condition: like new (used), Year of construction: 2022, functionality: fully functional, total height: 1,770 mm, total width: 600 mm, total length: 617 mm, input voltage: 230 V, type of cooling: air, Equipment: documentation/manual, type plate available, Thanks to the enclosed construction cartridge system, this 3D printer is ideally suited for prototype construction, the dental field, or even for training purposes, as there is no contact with the metal powder – neither during the component preparation nor during the printing process itself. AL3D-METAL 200-100 3D metal printer for additive manufacturing LASER TYPE: Fiber laser Wavelength: 1070 nm Average power: 200 W Operating mode: CW Focus diameter: 50 μm Scanning speed: max. 5 m/s Process parameters: Option to comprehensively influence the process parameters INCLUDES 9 CONSTRUCTION CARTRIDGES: Build volume: r Ø 100 mm; z 60 mm Layer thickness: 10 - 50 μm Achievable component density: > 99 % Hsdpfx Ajzlnh Renyju SOFTWARE AL3D-OS Operation: via 15.6" touchscreen, keyboard, and mouse Connectivity: 1x Ethernet; 2x USB CAD import file format: STL Print preparation: Simple support generation. Slicer integrated into the software.

Condition: like new (used), Year of construction: 2014, operating hours: 10 h, functionality: fully functional, Fiber optic optical inspection system with various endoscopes, as shown in the attached photos. Hedpfsz Dicqjx Anyeu

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, operating hours: 100 h, Gravimetric dosing and mixing system: Mixing system with 5 gravimetric dosing units 5 units: • Gravimetric screw dosing unit • Feeding hopper with pneumatic rotary valve, each with a lid • Screw conveyor for feeding from a big bag, with height-adjustable individual stand 1 unit: • Trough screw for combining and conveying the dosed materials into a transfer container. 5 units: Hjdpjt S Rdusfx Anysu • Big bag feeding station, with a suspension crossbeam to prevent the big bag from collapsing during emptying. • Big bag disc base with discharge aid (vibration drive) Option not included in the price: Control cabinet including control system Delivery EXW

Condition: used, Year of construction: 2013, functionality: fully functional, machine/vehicle number: NS-009-0000-300, type of input current: AC, nominal power at 50% duty cycle: 250 kVA, throat depth: 300 mm, short-circuit current: 50,000 A, input voltage: 400 V, type of cooling: water, total width: 1,000 mm, total length: 1,000 mm, total height: 1,850 mm, overall weight: 1,000 kg, open-circuit voltage: 22 V, Zens Multifunction Resistance Welding Machine 250 kVA MF – 23 kN – 50 kA – Year of Manufacture 2013 For sale is a high-quality Zens multifunction resistance welding machine in a robust industrial design. The system was developed for demanding resistance welding processes and is ideally suited for series production in the automotive, supplier, electrical, and metal industries. The machine operates with modern medium frequency (MF) technology and achieves a welding power of 250 kVA at a 50% duty cycle. The powerful SER medium frequency inverter (700 A) enables a maximum welding current of 50 kA and ensures maximum process stability as well as reproducible welding results. With a maximum welding force of 23 kN and an overhang of 300 mm, the system is suitable for a wide range of resistance welding applications. Hsdpfxjzqucfe Anysu Technical Data Manufacturer: Zens Machine Type: Multifunction Resistance Welding Machine Year of Manufacture: 2013 Welding Power: 250 kVA (Medium Frequency / MF) at 50% duty cycle Max. Welding Current: 50 kA SER Medium Frequency Inverter: 700 A Welding Control: SER-Mega1 Maximum Welding Force: 23 kN Overhang: 300 mm Equipment CE-compliant protective enclosure CE safety light curtain Welding table for welding forces up to 23 kN Pressure compensation tool QSF-M quality assurance system Position measuring system for process monitoring PLC control (Siemens S7) Robust industrial design for continuous industrial operation The combination of powerful medium frequency technology, precise force and position control, and modern PLC and SER welding control ensures high process reliability and consistently reproducible welding results. Thanks to the complete CE safety equipment, the machine can be easily integrated into existing production lines. The system is in good condition and can be inspected and demonstrated at any time by prior appointment.

Year of construction: 2021, condition: like new (used), functionality: fully functional, Component 1: ATM-800 P Tangential Dereeler (2 pieces) Heavy-duty dereeler for controlled unwinding of copper wire coils. • Max. coil diameter: 800 mm • Max. coil width: 300 mm • Pickup hole: Ø52 / Ø56 mm Hjdpfsz Ap R Isx Anyeu • Max. coil weight: 300 kg • Braking force: 100 - 2000 N • Brake torque: 3 - 800 Nm • Max. speed: approx. 5 rpm • PLC control with torque sensor Component 2: HBK-40-S Automatic Taping Machine Professional automatic taping machine for coil and conductor insulation. • Servo-controlled taping head • Operator terminal and display • Integrated X-axis guidance • Electric hysteresis brake • Automatic overlap control via encoder • Suitable for various insulation materials

Condition: used, Turning station RITTAL / E SYS-K System GmbH Automated turner for packaging made from ALU system profile Swivel station with roller conveyor, ALU system profile BOSCH REXROTH Weight of turning device: 730 kg Hedjv Tdkbopfx Anysu As-new condition

Condition: good (used), Year of construction: 2020, functionality: fully functional, total length: 9,000 mm, Adhesive application cell with ABB robot IRB 4600-60/2.05. Included in the adhesive application cell: Robot (weight 425 kg, payload 60 kg, year of manufacture 2020) 7th axis + steel structure (unlike in the images, the axis and steel structure have been extended to approximately 9 m) Adhesive application units Protective fences, etc. Not included: Roller shutter doors Fixturing device (available separately) Detailed drawings available upon request. Hsdpjzz Agmofx Anyou

Year of construction: 2013, operating hours: 7,700 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 12090, This is a recycling extruder with side feeding for materials (flakes, pellets, etc.). The system is supplied with a control cabinet and a double vacuum system. The pelletizing system is missing at the end of the screw – it is not included in the scope of supply. The cylinder ends at the flange. The extruder is supplied without a screw. The frequency inverter for the main motor was replaced with a new unit 3 years ago. Installed power approx.: 474 kW Cooling water requirement approx.: 190 l/min Fresh water consumption approx.: 110 l/h Feeding system: • Diameter of the feeding screw: 200 mm • Drive for the feeding screw: 45 kW, frequency-controlled • Hopper capacity net 7 m³/250 ft³, • Gear motor 3 × 3 kW • 2 sight glasses in the hopper • 2 level indicators Extruder: • Diameter of the extruder screw: 145 mm • L/D ratio: 24 • Heating power: 50 kW • Extruder drive unit 280 kW Vacuum 1: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 11 kW • Vacuum capacity: 225 m³/h Hodpoznz Ezsfx Anyju • Vacuum pressure: 33 mbar Vacuum 2: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 7.5 kW • Vacuum capacity: 190 m³/h • Vacuum pressure: 33 mbar Cylinder: • Cylinder: Bimetal extruder cylinder, • Reinforcement layer 1.8–2.0 mm thick, • Hardness 63–65 HRC Installation conditions: • Voltage: 3 × 400 Volts • Permissible fluctuation max.: +5 % – 5 % • Frequency: 50 Hz Permissible fluctuation max.: +4 % – 4 % • Protective measure: Multiple grounding • Ambient temperature: min. 15 °C, max. 35 °C • Humidity max.: 90 % • Altitude of the installation site: 0 – 1000 m The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is without packaging.

Condition: repair required (used), Year of construction: 2010, operating hours: 7,700 h, functionality: not functional, machine/vehicle number: 15158-10, working range: 4,000 mm, sheet thickness (max.): 12 mm, sheet thickness steel (max.): 12 mm, CNC plasma cutting system BACH ThermoCut 2000 with pipe cutting device, TEKA dust extraction system, and plasma source. Manufacturer: BACH Maschinenfabrik GmbH Type: ThermoCut 2000 Year of construction: 2010 For sale is a used CNC plasma cutting system BACH ThermoCut 2000, including pipe cutting device, plasma source, dust extraction system, and complete piping. The system was used in our machine manufacturing company until recently and is suitable for cutting sheet metal as well as processing pipes. Technical data: Working area: 4,000 x 2,000 mm Plasma source: Thermal Dynamics Ultra-Cut 100 CNC control: myBach Pipe cutting device included Pipe diameter: min. 50 mm max. 320 mm Max. cutting thickness: Mild steel: up to 12 mm Stainless steel: up to 10 mm TEKA filter and dust extraction system included Complete dust extraction piping system included CE marking available Maintenance and condition The system was regularly maintained during its entire service life. Official maintenance by the manufacturer was last performed on August 20, 2013. After that, ongoing maintenance was carried out in-house. Filters of the TEKA dust extraction system were renewed approximately 6 months ago. Cutting torch head was renewed approximately 4 years ago. Cooling water filter is changed regularly, approximately once a year. The operating hour counter of the dust extraction system currently shows approximately 7,700 hours. Since the system was operated exclusively with the dust extraction system running, this value can be used as a good indication of the total operating time of the system. Known defect The system is currently not operational. After consultation with Voortman and Mr. Sobiech from Magma Industries, the cause is likely to be in the cooling circuit of the plasma source. According to the experts, the most likely causes of the fault are: Defective cooling water pump Defective flow sensor Leakage on the suction side of the cooling water system A final fault diagnosis has not yet been carried out. Spare parts for the installed Thermal-Dynamics plasma source are now only available to a limited extent. The machine is therefore explicitly sold as a system requiring repair or for refurbishment. Scope of delivery BACH ThermoCut 2000 CNC system Thermal Dynamics Ultra-Cut 100 plasma source Pipe cutting device TEKA filter and dust extraction system Control panel with controller Dust extraction piping Accessories according to existing equipment Special features ✅ Pipe cutting up to Ø 320 mm ✅ Complete package including dust extraction ✅ Solid industrial machine made in Germany ✅ Easy-to-disassemble gantry design ✅ Also interesting for buyers who already have a suitable plasma source Location Hedpfxezizkyj Anyeu 24161 Altenholz, Germany Price Negotiable €21,900 Inspection possible by appointment. Sale exclusively to commercial businesses, excluding any warranty for defects. Loading / Dismantling The system is offered exclusively for self-dismantling and self-collection. The buyer assumes full responsibility for the dismantling, loading, and removal of the machine at their own cost and risk. To assist with loading, a hall crane with a maximum lifting capacity of 10 tons is available on site. Use of the crane can be arranged in advance. Due to the size and weight of the system, we recommend an inspection before submitting an offer.

Condition: excellent (used), Year of construction: 2016, operating hours: 3,000 h, functionality: fully functional, machine/vehicle number: 565697, type of input current: three-phase, input voltage: 400 V, belt width: 600 mm, conveyor belt width: 600 mm, The Wagner non-ferrous metal separator (NE separator), model 0429 from Wagner Magnete, is one of the manufacturer’s high-performance eddy current separators. Working width: 600 mm. Hjdszl Rfxjpfx Anyou • Throughput: depends on the material and grain size. • Rotor speed: up to 3,000 revolutions per minute. • Belt speed: 0.5 to 2.0 m/s. • Weight: 1.2 tons. • Rotor system: Eccentrically mounted with a high pole-changing frequency. • Rotor drive: 4 kW; belt drive: 1.5 kW. The machine and the associated control panel are included in the delivery. The machine was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner’s expense and can be delivered EXW at a port or in the production facility. The details for optimal transport need to be clarified. The machine price is quoted without packaging on a pallet.

Year of construction: 2013, operating hours: 3,500 h, condition: used, functionality: fully functional, machine/vehicle number: 12400, TSM/tsi oscillating sieve machines are used for the classification, screening, and dust removal of bulk materials from almost all industrial sectors, such as stones and soils, chemicals, mining, pharmaceuticals, feed, and food. The machine for sale has a diameter of 1200 mm and is equipped with 3 sieve decks with mesh sizes of 3 mm, 1.4 mm, and 0.463 mm. In addition, spare sieves with the following dimensions are included: • 16 mm x 1 piece • 15 mm x 1 piece • 0.5 mm x 1 piece • 0.16 mm x 1 piece • 0.9 mm x 1 piece • 0.86 mm x 1 piece The drive has a power of 1.5 kW, 400 VAC, 50 Hz, 1450 RPM. The machine was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. Hodpfx Aezmzbmjnyou The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Condition: new, Year of construction: 2026, The item is generally a project-based product or, depending on availability, available as a demonstration machine. The purpose of the labeller is to fully automatically label a cylindrical product. Description - Machine materials: 1.4301 and anodised aluminium alloy Hjdpfxoq U Siho Anyju - Control via Siemens PLC + HMI - Cylindrical products from Ø20mm to Ø110mm - Accuracy: ± 1 mm (excluding product and label faults) - Technical documentation provided via regional partners Label roll - Inner diameter: 76 mm - Outer diameter:

Year of construction: 2026, condition: new, The equipment is generally considered project stock or, depending on availability, can be offered as a demonstration machine. Application: Accurate dosing of free-flowing products in precise quantities. Hjdpfxoq T R Sbo Anyou Scale Features - Easy operation - Fast and uncomplicated cleaning - Low maintenance requirements - Tool-free assembly and disassembly of all product-contacting format parts - Low maintenance requirements - Corrosion-resistant stainless steel construction (1.4301) - Entire control system integrated within the machine housing - Continuously adjustable vibration system for optimal product flow - High accuracy through combination weighing Technical Data - Number of weighing heads: 10 - Weighing hopper volume: 2.5l - Weighing range: 10 - 1000g / 2,500g - Accuracy: ±0.2-1.5g - Speed: 60 bags/min (depending on product) - Control panel: 7" touchscreen display - Power: 1kW / 230V / 50Hz - Dimensions (LxWxH): 1620mm x 1100mm x 1110mm - Machine weight: 380kg

Year of construction: 2021, operating hours: 300 h, condition: used, functionality: fully functional, machine/vehicle number: I100, Florapower industrial continuous screw-press processing system, manufactured in Germany and commissioned in October 2021. Hedpfx Anezz Nvzsyeu The machine has accumulated less than 300 total operating hours and is in very good, fully operational condition. The system was originally configured for the continuous, solvent-free mechanical processing of dried hemp flowers and the production of hemp/CBD oil. In addition to hemp processing, the Florapower screw-press technology can also be used for the mechanical processing and cold pressing of a broad range of dry oil-bearing seeds and other suitable raw materials. Exact capacity and process parameters depend on the raw material, screw configuration and required final product. The system features: automated raw-material feeding and dosing industrial continuous screw-press technology PLC / touchscreen process control adjustable operating parameters stainless-steel process components continuous mechanical pressing solvent-free processing concept Manufacturer: Florapower GmbH, Germany Year: 2021 Commissioned: October 2021 Operating hours: less than 300 h Condition: very good / fully operational Original machine purchase price: approx. EUR 96,000 excluding installation and transport Total original investment: approx. EUR 110,000 Location: Slovenia, European Union Asking price: EUR 85,000 – negotiable The machine can be inspected and demonstrated under operating conditions by appointment. Detailed photographs, operating videos and additional technical documentation are available for serious buyers. Dismantling, loading and international transport can be agreed separately with the buyer. Reason for sale: change of production focus.

Condition: used, Year of construction: 2022, operating hours: 10 h, functionality: fully functional, machine/vehicle number: NS-009-50Hz-11kN-300, type of input current: AC, nominal power at 50% duty cycle: 160 kVA, throat depth: 300 mm, short-circuit current: 25,000 A, input voltage: 400 V, type of cooling: water, total width: 1,000 mm, total length: 1,000 mm, total height: 1,850 mm, overall weight: 1,000 kg, open-circuit voltage: 15 V, Zens Multifunction Spot Welding Machine 160 kVA – 50 Hz – 11 kN – Year of Manufacture 2022 For sale is a Zens multifunction spot welding machine in a robust industrial design. The machine is designed as a 50 Hz alternating current system and is suitable for various spot welding applications. The machine features an integrated seam welding adapter. The corresponding seam welding heads are not included in the scope of delivery and can be purchased separately. Thanks to the modular design of the machine, it is possible to use different welding tools and applications. Technical Data Manufacturer: Zens Model: NS-009 Machine Designation: Multifunction Spot Welding Machine Year of Manufacture: 2022 Welding Technology: Alternating Current (AC), 50 Hz Welding Power: 160 kVA Duty Cycle: 50% Max. Welding Force: 11 kN Welding Control: SER PLC Control: Siemens CE Safety: 2-Hand Control Seam Welding Adapter: Integrated Equipment Zens Multifunction Spot Welding Machine 50 Hz Alternating Current Technology Integrated Seam Welding Adapter SER Welding Control Siemens PLC Control Device Carrier System with Touchscreen 2-Hand Control as CE Safety Device Modular Machine Design Robust Industrial Design Available Separately The seam welding heads are not included in the machine's selling price and can be purchased separately. The "On Top" water cooling unit is also not included in the machine's selling price and can be purchased separately. Hedpfx Aeztn Sxonyou The machine is in good condition and can be inspected and demonstrated by appointment. Note: Seam welding heads and the "On Top" water cooling unit are available separately and are not part of the machine offer. Subject to technical changes and errors.

Condition: new, Year of construction: 2026, The product is generally a project-specific item or, depending on availability, can be provided as an exhibition machine. Hsdpohtrf Eefx Anyou Produce bags according to the desired format, fill them with the product, and seal them. Description: - Optimal price-performance ratio - Easy operation and cleaning - Low maintenance requirements - Product-contacting parts suitable for food applications (1.4301, NBR) - Control system fully integrated into the packaging machine - Control is performed by a PLC, with a color touch display and intuitive operating software - Quick bag format change without tools - One flat bag format included - Technical documentation provided by regional partners Technical data: - Intermittent heat sealing for heat-sealable films - Film thickness: 0.03 mm to 0.15 mm - Film width: 180-520 mm - Bag dimensions (L x W): 60-350 mm x 70-250 mm - Cycle rate: 15 - 40 bags/min. (depending on the product) - Electrical power: 3.2 kW / 230 V / 50 Hz - Compressed air consumption: 360 l/min at 6 bar - Dimensions (L x W x H): approx. 1700 mm x 1300 mm x 1850 mm - Weight: approx. 500 kg Options: - Additional format sets - Stand-up pouch modification - Printing unit (thermal transfer, hot stamping, inkjet) - Adjustment of height, etc.

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, input voltage: 400 V, input current: 21 A, type of input current: DC, volume flow: 6,045 m³/h, overall weight: 1,100 kg, ALKO ECO JET 60/5 HD extraction unit, without control software. Hjdpfx Aoyrqnzsnysu Dust extraction unit, chip extraction, self-cleaning filter, vacuum-based ALKO ECO JET. The filter is pneumatically cleaned with pulses of compressed air during operation, ensuring high device efficiency. It is ideally suited for all types of dry dust generated in various technological processes. Filter bags can be replaced according to specific requirements and intended use.

Condition: like new (used), Year of construction: 2021, operating hours: 3,006 h, functionality: fully functional, machine/vehicle number: 00161215-02.18, type of input current: three-phase, total height: 1,150 mm, total width: 1,200 mm, total length: 1,030 mm, input voltage: 400 V, overall weight: 910 kg, type of cooling: water, electrical fuse: 16 A, laser power: 900 W, input frequency: 50 Hz, laser wavelength: 1,070 nm, travel distance X-axis: 320 mm, travel distance Y-axis: 330 mm, travel distance Z-axis: 370 mm, Equipment: head guard, We are selling a laser welding machine in excellent condition. Hodjzw Eu Sepfx Anyou

Year of construction: 1992, condition: used, functionality: fully functional, machine/vehicle number: 029.700, Painting/drying booth from Luft- und Trockentechnik GmbH, type KSP 6-BT, manufactured in 1992. The system is suitable for painting and drying workpieces and features an integrated exhaust/extraction system. Technical data: Hsdpsz D Evysfx Anyeu Manufacturer: Luft- und Trockentechnik GmbH Type: KSP 6-BT Year of manufacture: 1992 Manufacturer's number: 029.700 Usable volume: approx. 72 m³ Total volume: approx. 81 m³ Minimum exhaust air volume flow: 1,440 m³/h Maximum permissible oven temperature: 90 °C Maximum solvent quantity: 4,302 g/oven load The painting booth has dimensions of 6 x 4 meters. The system includes an exhaust duct with extraction via the roof. In addition, a suspension/transport system is located in the ceiling area, to which workpieces or painting racks can be attached and moved through the work area. Dismantling will be carried out by the buyer.