Used Co2 Installation & Cold Room for sale (10,023)

Year of construction: 1991, condition: used, Volume: 15 hl Dedpfow Tml Esx Ad Nscg Periphery: Pump

Year of construction: 1995, condition: used, This filter system may only be used to filter preclarified products that have normal filterable properties in their composition. Max. filtration flow: 400 hl/h continuous Permissible operating pressure: 6 bar Permissible operating temperature: 105 °C Dsdsvcqv Nspfx Ad Nscg Volume: 1456 l Current: 10 A Voltage: 220 V Water: cold water: min. 150 hl/h; hot water (max 65 °C): min. 150 hl/h Compressed air: prepared compressed air: 4 - 6 bar; control air: 5 - 8 bar Weight: 3450 kg Base construction: basic frame with control and measuring components and filter container; cleaning module Features: 98 filter cartridges, 3 piston diaphragm pumps (Dosage), centrifugal pump with frequency converter (WT circuit), various analog and digital sensors (flow, pressure, level, temperature, conductance), various valves, control cabinet

Year of construction: 2001, condition: used, The Pall CFS system is designed as a single unit and can be installed directly in front of the filling line without the need for a buffer system. It is a completely independent process unit consisting of the following components: filter vessel Piping and connections Membrane cleaning system (CIP) integrity check Switchboard The hygienic design, the simple integrity test and the full automation ensure the microbiological safety of the system and usually allow the operation of the filling staff. Cluster filtering groups filter elements into clusters. Each cluster has its own outlet valve. During filtration, all clusters are open. Cleaning, sterilization and integrity testing are performed per cluster. Advantages of the CFS principle; Longer life Integrity testing on site Integrity diagnostics per cluster Special rinsing High specific flow rate Short flush times Constant flow in all candles Minimal water consumption Quick replacement of filter elements Controlled backwash Minimal beer loss High biological safety Constant availability With this filter system only preclarified products may be filtered, which have normally filterable properties in their composition. Max. filtration flow: 400 hl/h continuous Dodpfjvcqx Dsx Ad Necg Permissible operating pressure: 6 bar Permissible operating temperature: 105 °C Volume: 1456 l Current: 10 A Voltage: 220 V Water: cold water: min. 150 hl/h; hot water (max 65 ° C): min. 150 hl/h Compressed air: prepared compressed air: 4 - 6 bar; control air: 5 - 8 bar Length: 1,40 m Width: 1,20 m Height: 1,85 m Weight: 3450 kg Base construction: basic frame with control and measuring components and filter container; cleaning module Features: 98 filter cartridges, 3 piston diaphragm pumps (Dosage), centrifugal pump with frequency converter (WT circuit), various analog and digital sensors (flow, pressure, level, temperature, conductance), various valves, control cabinet

Condition: refurbished (used), Year of construction: 1980, For sale: Kaltenbach cold circular saw – Various versions and models in stock. The machine has been extensively overhauled both technically and visually. Dcsdpfx Ajy Iycbed Neg Gearbox, of course, backlash-free! Type: KKS 400 H Saw blade diameter: 400 mm Motor power: 1.8/2.7 kW Cutting speed: 10/20, 13/26, 15/30 m/min Feed rate: 0 - 1,000 mm/min Rapid approach/return: 1,550 mm/min Maximum working range: 130 mm Square material working range: 120 mm Flat material working range: 305 x 20 mm Round material working range: 130 mm Minimum working range: 10 x 10 mm Miter range: 0° - 90° - 0° Dimensions (LxWxH): 1,080 x 900 x 1,760 mm Weight: 850 kg Inspection/collection in 89558 Böhmenkirch. Shipping available on request. Forklift available for loading.

Condition: refurbished (used), Year of construction: 1980, For sale is a Kaltenbach cold circular saw The machine has been technically and optically refurbished Gearbox naturally free of play! Type: KKS 400 H Saw blade Ø: 400 mm Motor power: 1.8/2.7 kW Cutting speed: 10/20 13/26 15/30 m/min Feed rate: 0 - 1,000 mm/min Fast forward/reverse: 1,550 mm/min Max. working range: 130 mm Working range square material: 120 mm Working range flat material: 305 x 20 mm Working range round material: 130 mm Working range min.: 10 x 10 mm Mitre range: 0° - 90° - 0° Dimensions LxWxH: 1,080 x 900 x 1,760 mm Weight: 850 kg Inspection / collection in 89558 Boehmenkirch Dedpfxey Iybdj Ad Njcg Shipping possible on request Forklift available for loading.

Condition: excellent (used), CTS Temperature Shock Test Chamber TSS-70/350-A Device Data Manufacturer: CTS GmbH Model: TSS-70/350-A Year of manufacture: 10/2017 Version: Temperature Shock Test Chamber Cooling unit: Water-cooled Description Used temperature shock test chamber by CTS. Suitable for shock and temperature cycling tests. For use in industry, research, and quality assurance. Areas of Application - Material testing - Aging tests Dcodpfsy H Hk Aex Ad Nog - Electronics and component testing - Temperature shock tests - Automotive and QA Temperature Ranges Hot chamber: +50 °C to +220 °C Cold chamber: -70 °C to +100 °C Electrical Data 400 V / 3/N / 50 Hz Power: 19.8 kW Current: 46.5 A Connection: CEE 63A Refrigeration System Precooling: R452A, 7.2 kg Cooling stage: R23, 2.8 kg CO₂ equivalent: 15.41 t / 41.59 t Water-cooled Pressure / Protection PS: 25 bar PT: 27.5 bar IP 54 Features - Touchscreen control - Microprocessor controller - Programmable operation - Digital setpoint/actual display - 2-zone system - Transfer cart for rapid specimen transfer - Viewing window - Integrated control cabinet - Cooling water connections Technical Construction - Separate hot and cold chambers - Stainless steel test space - Industrial-grade construction Dimensions External: 2335 x 940 x 1820 mm Handling dimensions: 1990 x 940 x 1652 mm Internal: 410 x 480 x 660 mm Weight Approx. 950 kg Documentation - Declaration of conformity - Test certificates - Operating manual - Circuit and piping diagram - Spare parts list Service before delivery (optional) - Functional check - Refrigerant service - Leak test - Test run with log Condition Used. Cosmetic condition as shown in photos. Scope of Delivery - Test chamber TSS-70/350-A - Documentation (where available) Note Used machine, sale without warranty. Inspection can be arranged upon request. Loading and transport can be organized if required. Subject to prior sale and technical modifications. For any questions, please feel free to contact us.

Condition: used, functionality: fully functional, very robust gearbox, motor 1.0 / 1.8 kW Saw blades: 360 mm Djdsy Iv Hiopfx Ad Necg Slow-running model with 6 cutting speeds: 8 / 10 / 12.5 m/min 16 / 20 / 25 m/min Test cutting at our facility with the following specifications: Cutting capacity at 90 degrees with blade size 360 mm: Round profile: 110 mm Solid round material: 80 mm Flat profile: 200 x 80 mm Weight approx. 560 kg

Condition: new, Year of construction: 2026, 560 mm Dcedpfsy H N Spsx Ad Nog 320 mm 400 mm 950x450 mm 1050x320 mm 25-3600 U/min DIN 69871 SK 40

Condition: new, Year of construction: 2026, 560 mm 320 mm 400 mm 950x450 mm 1050x320 mm 25-3600 U/min SK 40 Dcodoy H N Siepfx Ad Njg

Condition: excellent (used), CTS Type: TSS-70/350-A Water-cooled refrigeration unit For sale is a high-quality temperature shock test chamber from CTS (Clima Temperatur Systeme), model TSS-70/350-A. This unit is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance. Typical applications: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical specifications: Type: TSS-70/350-A Temperature range: Warm chamber: +50°C to +200°C Cold chamber: -70°C to +100°C Electrical data: Connection: 400 V, 3/N, 50 Hz Rated power: approx. 20.4 kW Rated current: approx. 36.5 A Refrigeration system: Refrigerant: R404A / R23 Precooling stage: approx. 6.0 kg Cooling stage: approx. 3.0 kg Water-cooled Features / Equipment: - CTS control panel with touch display - Microprocessor-controlled regulation and monitoring system - Program operation - Digital setpoint and actual value display Dcjdsy Hkgbepfx Ad Njg - 2-zone system (warm and cold chamber) - Automatic transfer basket for shock tests Technical design: - Warm and cold chamber separated - Transfer basket system for rapid temperature change - Test chamber made of stainless steel - Insert shelf / wire rack - Viewing window in door - Water cooling connections available - Integrated control cabinet Dimensions: External dimensions (HxWxD): approx. 2335 x 940 x 1820 mm Installation dimensions (HxWxD): approx. 1990 x 940 x 1652 mm Internal dimensions (HxWxD): approx. 410 x 480 x 660 mm Weight: approx. 950 kg Additional data: Protection class: IP 54 Operating overpressure: approx. 25 bar Test pressure: approx. 27.5 bar For your safety as a buyer, please note the following information! The following points are carried out on the chambers we offer before sale: 1. Functional check and replacement of necessary components 2. If needed, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented test run Condition: used Scope of delivery: see pictures (Specifications subject to change and errors excepted!) We are happy to answer any further questions by phone.

Condition: excellent (used), CTS Type: TSS-70/130 Water-cooled chiller unit For sale is a high-quality thermal shock test chamber manufactured by CTS (Clima Temperatur Systeme), model TSS-70/130. This device is designed for thermal shock testing and is commonly used in industry, research, and quality assurance. Application fields: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical specifications: Type: TSS-70/130 Test volume: 130 liters Temperature range: - Hot chamber: +50°C to +200°C - Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from room temperature to +180°C Cooling rate: approx. 4 K/min from room temperature to -60°C Temperature deviation: ±1 K over time ±2 K spatially Temperature change rate: Max. 100 K/min on average for shock test cycles (without radiant heat) Transfer rate: ≤ 15 min in the range -65°C to +200°C with 10 kg ICs Transfer time: < 10 seconds Dcodsy Hkfdjpfx Ad Njg Electrical data: Connection: 400 V, 3/N, 50 Hz Nominal power: approx. 16.7 kW Nominal current: approx. 26.8 A Site-side fuse: 32 A slow-blow Connection: Cekon 32 Cooling system: Refrigerant: R404A / R23 Water-cooled, low noise, fully hermetic Features and equipment: - CTS control panel - Microprocessor-controlled regulation and monitoring system - Program operation (up to 100 test programs) - Digital setpoint/actual value display - RS232 interface - 2 free switching channels for controlling test objects on-site - Fault alarm with floating contact (rated for up to 30 V-DC, 2 A) - EMC tested Technical design: - Hot and cold chambers - Transport basket with spindle drive - Test chamber / basket made of stainless steel, Material no. 1.4301 - Insert basket made of stainless steel wire - Pipe duct NW 50 with closing plug - Compressed air connection 1/4" male - Pressureless condensate drain R 1/2" internal thread - Safety door lock - Lockable door with window Dimensions as per installation drawing: External dimensions approx.: 2335 x 940 x 1820 mm Entry dimensions approx.: 1990 x 940 x 1652 mm Test chamber dimensions: Height approx. 410 mm, Width approx. 480 mm, Depth approx. 660 mm Window: 300 x 300 mm Further data: Degree of protection: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average power consumption per test cycle: approx. 8 kWh For your assurance as a buyer, the following procedures are performed on all offered chambers beforehand: 1. Function check and replacement of necessary components 2. If required, recharge with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented trial run Condition: used Scope of delivery: see pictures (Specifications subject to change and errors excepted!) If you have further questions, we are happy to assist you by phone.

Condition: excellent (used), CTS Type: TSS-70/130 Water-cooled refrigeration unit For sale is a high-quality thermal shock test chamber by CTS (Clima Temperatur Systeme), model TSS-70/130. This device is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance. Application Areas: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical Specifications: Type: TSS-70/130 Test volume: 130 liters Temperature range: - Hot chamber: +50°C to +200°C - Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from ambient temperature to +180°C Cooling rate: approx. 4 K/min from ambient temperature to -60°C Temperature deviation: - ±1 K over time - ±2 K spatially Temperature change rate: - max. 100 K/min average for shock test mode (no radiant heat) Transfer time between chambers: - ≤ 15 min for -65°C to +200°C with 10 kg ICs Changeover time: - < 10 seconds Electrical Specifications: Connection: 400 V, 3/N, 50 Hz Nominal power: approx. 17.2 kW Nominal current: approx. 29 A Site fuse: 32 A slow-blow Connection: Cekon 32 Refrigeration System: Refrigerant: R404A / R23 Water-cooled, low noise, fully hermetic Features/Equipment: - CTS control panel - Microprocessor-controlled regulation and monitoring system - Programmable operation (up to 100 test programs) - Digital setpoint and actual value display - RS232 interface - 2 free switching channels for external device control - Fault notification via volt-free contact (Loadable up to 30 V DC, 2 A) - EMC tested Technical Construction: - Hot and cold chambers - Transfer basket with spindle drive - Test chamber/transfer basket made of stainless steel (material no. 1.4301) - Stainless steel wire insert basket - Tube port NW 50 with sealing plug - Compressed air connection 1/4" male - Non-pressurized condensate drain R 1/2" female thread - Safety door locking - Lockable door with window Dimensions (according to installation diagram): External dimensions approx.: 2335 x 940 x 1820 mm Installation clearance approx.: 1990 x 940 x 1652 mm Test chamber internal dimensions: height approx. 410 mm, width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Additional Data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh Dsdpfx Aey Hkd Hjd Necg Important information for your safety as a buyer! The following points are performed on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If required, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented test run. Condition: used Scope of delivery: see photos (Specifications subject to change and errors excepted.) For further questions, please feel free to contact us by phone.

Condition: excellent (used), Year of construction: 2021, machine/vehicle number: 381-30-09/21, Dedicated line for cutting ALU profiles. 3-axis line for 90° cutting of short aluminium profiles. Profile dimension: 30 x 15 mm. Cut length: 14 mm. Djdpey Nxh Ssfx Ad Necg

Condition: excellent (used), Year of construction: 2007, BIMAX TA 91 Automatic Circular Saw TECHNICAL DATA Total power requirement, rotary current: 3 x 400 V For pneumatic machines: 3 kW For hydraulic machines: 3 kW Customer-provided mains fuse: 16 A Supply line: 4 x 2.5 mm, 3P + E Air connection: Diameter: 12 mm Supply line: 8 – 10 bar, 40 l/min Operating pressure: 6 bar Spindle drive via three-phase motor: B5-100S Dodpfx Asv I Dmled Necg 4/2-pole, Dahlander circuit: 1420 / 2840 rpm Power: 1.8 / 2.5 kW Saw blade mount: 32 mm Drive pin: 8 mm Pitch circle of drive pin: 45 mm Cutting wheel mount: 22 mm Saw blades: 160 x 1 to 300 x 2 mm Passage range: Round up to 65 mm Square up to 55 x 55 mm Rectangular up to 80 x 50 mm Standard clamping jaw for diameters: 10 – 60 mm Material feed length: 0 – 250 mm Saw weight: 500 kg Hydraulics: 120 kg No liability is assumed for the accuracy, completeness, or timeliness of this information.

Condition: good (used), Year of construction: 2002, Behringer Eisele VA-0-250-NC Circular saw TECHNICAL DATA Sawing range: 90 ° Saw blade diameter: 25 cm Bore: 40 mm Cutting range: 10-75 mm Cutting length: 5-900 mm Speed: 2800 rpm Cutting speeds: 26/52/103/206 SFPM or 0.13/0.26/0.52/1.05 m/s Feed speeds: 0-40 mm/sec NC axis: Yes Dimensions: 190 x 127 x 190 Weight: 1300 kg We assume no liability for the accuracy, completeness and up-to-dateness of the information provided Dedpfevdk A Ejx Ad Nscg

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 107500 € 2031.75 € 360 mm Ø360 x 40 mm 40 - 280 U/Min Dcodpfx Adoy Nnxgj Nsg rund: 20 - 100 mm; quadra 60 mm 10 - 9999 mm 900 mm 15 kW 3400 mm 2675 mm 2750 mm 3450 kg 21,65 kW Mass production in continuous operation is done by BMDO 100 XS when producing cut-off pieces of steel and non-ferrous metals with a material cross-section up to a diameter of 100 mm. BMDO 100 XS is designed to be used with TCT circular saw blade in order to cut solid bars in high speedand excellent precise. It is also suitable for HSS blades to cut tubes. With the Standard 800mm stroke servo feeding and 6 meters automatic loader. BMDO 100 XS is perfect for large-scale production of solid bars. STANDARD ACCESSORIES: automtic loader 6 m motorized roller table 3 mMikrospray Coolant Hydraulic Vice Inverter Control Panel Saw Blade Brush Cover Switch Heavy Duty Gearbox OPTIONAL EQUIPMENT (prices on request): mist filter 6 m roller table

Condition: as good as new (ex-display), functionality: fully functional, Compact and quiet CO2 laser with a maximum marking area of 460 x 305 mm (L x W) and a maximum object height of 145 mm. Possible applications: Ideal for laser engraving and laser cutting of plastics, wood, glass, and other organic materials, as well as coated surfaces. Engrave glass, produce plastic signs, cut, mark, and define crease lines on paper. High-quality construction: The laser engraver features a one-piece aluminum housing and includes professional CAD/CAM software and an RF laser source. Efficient and safe operation: This space-saving laser is equipped with an automatic scanning function, autofocus for automatic vertical adjustment, an integrated control panel, and an illuminated marking table with a wide front loading door. In addition, a built-in air compressor ensures a clean lens, and an exhaust system is integrated. Laser parameters can be stored in a library. Multi-technology software: Centralized management of settings, designs, and results within a single working environment. Equipped with a point-and-shoot function for easy positioning and job setup as well as a print-and-cut function for cutting printed materials. Dimensions: 775 x 725 x 450 mm Marking area: 460 x 305 mm Max. object height: 145 mm Dcedpfx Aey Ia Dxed Neg Max. speed: 2,540 mm/s Laser source: CO2 Power: 40 W Software: Gravostyle software (included)

Condition: reconditioned (used), Year of construction: 2002, functionality: fully functional, travel distance X-axis: 2,500 mm, travel distance Y-axis: 1,600 mm, travel distance Z-axis: 1,200 mm, rapid traverse X-axis: 15 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 15 m/min, feed rate X-axis: 12 m/min, feed rate Y-axis: 12 m/min, feed rate Z-axis: 12 m/min, spindle speed (max.): 3,000 rpm, table width: 1,200 mm, mount diameter: 50 mm, power: 0.028 kW (0.04 HP), SORALUCE TR-25 included installation and commissioning Year of manufacturing: 2002 Dcjdpferp H D Tox Ad Njg Capacities / travel: Axis (X): mm 2.500 Vertical (Y): mm 1.600 Ram (Z): mm 1.200 Table size: Length: mm 2.860 Width: mm 1.200 Painting: RAL 5005 and RAL 7035 Tool taper: ISO 50, DIN 69871 Form AD Main Spindle Drive: Power: 100 % ED KW28 Spindle speed range: Spindle speed: rpm-1 20-3.000 Feeds: X-, Y- und Z-Axis mm/min 2 – 12.000 Max. rapid traverse speed: X-, Y- und Z-Axis mm/min 15.000 Weight: kg 22.200 Heidenhain 426 Heidenhain CNC control 426M with digital drive technology, electronic handwheel HR410 Automatic Milling Head, Diagonal H26 Automatically indexing Soraluce "Diagonal" milling head, type H26 including a long spindle for internal coolant supply. 2.5° division in both joints and speeds up to 3000 rpm. Clamping via Hirth serration in both joints. Repeatability of +/-3 sec. or 0.002mm. FAG spindle bearing with steel balls. Includes air lock. Chip Conveyor Automatic Tool changer: Maximum Tool Diameter: 125 mm Max. Tool Diameter with Adjacent Slots Free: 250 mm Maximum Tool Length: 400 mm Maximum Tool Weight: 20 kg Number of Magazine Slots: 40 Coolant lubrication system internally cooling 3D thermal expansion compensation Splash guard Our product line: RepairFIT RepairFIT is our proven offer for a profitable entry into our product lines. The machines available in this line have been procured by us following a strict selection process and have undergone a thorough examination (Deep-Dive-Check). After intensive cleaning, any detected and obvious defects or errors have been professionally repaired by our expert service team. What does this mean for you? A RepairFIT offer is ideal for you if you're looking for a used machine while also wanting guaranteed process safety. With this option, you receive a high-quality CNC milling machine that is immediately ready for error-free operation. With our professional service technicians, we implement the commissioning in your premises in the shortest possible time. You can start production right away. This is a clear difference from an ordinary used machine purchase. This solution offers you guaranteed process and planning reliability at an attractive fixed price Project Execution: Benefit from our turnkey project execution, which is included in all lines: Our team of experts provides comprehensive support in optimally determining the machine's location, creating a professional layout, and fully integrating it into your manufacturing process. We ensure that your CNC milling machine is expertly installed, commissioned, and precisely aligned according to the manufacturer's specifications! All from a single source, in the end, simply a process-reliable machine that does what it's supposed to do.

Condition: excellent (used), Year of construction: 2021, machine/vehicle number: 376-30-07/21, Dedicated line for cutting aluminium profiles. 6-axis line for cutting long aluminium profiles. Profile dimensions: 160x200 mm. Cutting length: 1500 mm. Dodpfey Nkp Iox Ad Nscg

Condition: good (used), Selling CRATHERN, PERONDI IA630, NA 900. Dcedpfx Aoud Axgjd Nsg

Condition: good (used), Year of construction: 1997, x-travel 600 mm y-travel 450 mm z-travel 400 mm Control Heidenhain 430 ITNC tool taper SK 40 voltage 400 V control voltage 24 V weight of the machine ca. 6 t - Operating hours: 48,690 - Spindle hours: 13,465 - Max. table load: 1,000 kg - Machine weight: 6,000 kg - Includes tool holders – SK40 - Includes all descriptions - Includes programming manual – Heidenhain Dsdpfjwbi A Dsx Ad Nscg - Includes 1 machine vice - Includes clamping claws

Condition: excellent (used), Year of construction: 1966, I sell a circular saw made in Germany. Company Eisele model vms II in good condition Dcedpfx Adevbwfnj Njg

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, saw blade diameter: 400 mm, cutting height (max.): 145 mm, cutting range round steel at 45°: 120 mm, type of input current: AC, Robust cold circular saw with pneumatic workpiece clamping Clamping, sawing, return to initial position, opening in automatic mode Stepless feed rate adjustment Minimum quantity lubrication system + coolant unit Dcodpfx Adoy Httdo Njg Saw blade diameter from 375 to 425 mm Mitre adjustment 45° - 90° - -45° - -30° Cutting capacity with saw blade diameter 400 mm: Flat: 210 x 120 mm Mitre cut: 145 x 120 mm Round: 140 mm diameter Mitre cut: 120 mm Pole-changing three-phase motor for saw blade – circumferential speed 22 + 44 m/min Voltage: 400 V

Condition: ready for operation (used), Year of construction: 2014, This BLM Adige LT8 4kW Co2 was manufactured in 2014. It features a Rofin DC035 3.5kw laser source and is equipped for tube cutting with a 3D cutting head. It handles materials up to 12mm thick and 206mm round, with lengths up to 6500mm. Consider the opportunity to buy this BLM Adige LT8 4kW Co2 tube cutting machine. Contact us for more information about this machine. Additional equipment • Bundleloader: 6.5 meters • Steploader: 6.5 meters • Output with Conveyor Belt: 6.5 meters at the front, 4.5 meters at the back Machine Benefits Technical Machine Benefits • Equipped with a 3d cutting head • Includes options such as weld detection, active focus, active scan, active piercing. • Laser source: rofin dc035 3. 5kw • Last maintenance: 24/6/2025 • Maximum weight: 35 kg/m • Maximum length: 6500mm • Maximum round diameter: 206mm • Maximum square: 200x200mm • Maximum thickness: 12mm Extra Information Dcedpfsx H A Rxex Ad Nsg Machine still under power

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, total width: 4,450 mm, total length: 4,550 mm, total height: 2,360 mm, temperature: 2 °C, We are offering this very well-maintained Viessmann cold storage room, year of manufacture 2017. Dcedpfx Adsyku N Tj Neg Manufacturer: Viessmann Year: 2017 Condition: very good Category ID: 261 Type ID: 1147 Machine type: Cold storage room Internal dimensions: 4.55m (L) x 4.45m (W) x 2.36m (H) Walls made of 80mm sandwich panels Floor made of 80mm sandwich panels Compressors: Tecumseh Silensys Evaporator: Kelvion Refrigerant: R134a The cold storage room was used for storing pharmaceuticals. It is still fully operational. Dismantling must be carried out by the buyer. If you have any questions or need further information, feel free to send us a message or give us a call.