Used Scherer Vdz 80 for sale (16,932)

Condition: good (used), Your contact person in our home: Mr: André evening Mr: Marcel Brahms Mr: Simon blank We offer you a used pallet rack beam on the manufacturer's Hovuma for sale. Technical specifications of the pallet shelf traverse: Shelf system: Hovuma Included in the scope of delivery: Nwedpfjd Ht T Dsx Ag Dof 01 x pallet shelf beams, used Material color: Green Finish: Floor - / head traverse INP-profile: 80 x 42 mm cage: 2 hooks Clearance: 2,880 mm maximum load per pair of traverse 1,600 kg, at gleichm. distributed load 02 x used locking pins, Execution: compl. zinc-plated To secure the beam against unintentional lifting Our services at a glance: (Prices on request) Installation, construction our general conditions of erection are to be observed Shelf testing Shelf inspection according to DIN EN 15635 carried out according to the Requirements of BGR 234 Visual inspection for all shelf systems Delivery with our own fleet of vehicles (without discharge)

Condition: good (used), Year of construction: 2004, more pieces industrial gas burners Oilon GP-80 H + double GasMultiBloc Dungs MB ZRDLE 420 B01 S20 +Dungs FRS 520 OILON GP-80 H Capacity: 350-1000KW established in 2005 Nedpfx Ascvkaleg Dewf Voltage: 230 / 400V 50HZ 2KW ip20 The controller LFL1.322 GAS drueck: min 20mbar / max 360mbar 62 kg Monoblock burner cast aluminum Electronic control panel is a signal diagram showing the different stages of combustion and alarms, allows you to keep constantly under control in the proper burner operation Flame type QRA2 Software relay LFL1.322 Gas train with an appropriate adapter is set on the side of the burner Adjustable burner flange Damper actuators Connect quick connector for the power cord Automatic termination of the air when the burner is switched off Seat and gas safety valves The reduction of the gas pressure regulator The differential air pressure switch Controller minimum gas pressure Luc overall control.

Condition: good (used), Year of construction: 1982, functionality: fully functional, Precision high-speed lathe make FEINBAU Machine No. 4891 Type PM1-FZB Year of manufacture 1982 Technical data : . Nwsdpfxoyfib To Ag Djf Maximum turning length 90 mm Swing diameter over bed 220 mm Swing diameter over support 110 mm Center distance 160 mm Bore 23 mm Drive motor 0.65 / 1 / 1.3 kW Space requirement , length x width 1.6 x 0.8 x 1.2 m Scope of delivery : Collet chuck device for collets : K23 DIN 6341 Collets Hand lever cross support with adjustable stops Hand lever boring vise, with 2 x MK1 holders and stops . .. Ongoing purchase of used German machines without NC or CNC control .

Condition: refurbished (used), battery capacity: 375 Ah, battery voltage: 48 V, total height: 625 mm, total length: 827 mm, total width: 411 mm, Tested forklift battery for your forklift - 48V 3PZS 375Ah - DIN A + 1-year warranty Nedswzvtijpfx Ag Dowf + Includes Aquamatik watering system + Includes end connectors & REMA 320 plug (other plug types can be installed on request) + Capacity: min. 90-100% (C5 capacity test protocol included with delivery) + Year of manufacture: 2024 Dimensions: Length: 827 mm Width: 411 mm Height: 625 mm Weight: approx. 560 kg Suitable for the following models and others: Linde E 16 - 386-00 Linde E 18 - 386-02 - side battery change Linde P 50 Z LONG - 368-00 Linde P 60 - Linde P 60 - side battery change Linde P 60 Z - 126-00 Linde P 80 - Linde P 80 - side battery change LInde T 30 R - 143-00 Linde W - side battery change Still LTX 70 Still R 06-06 Jungheinrich EZS 570 Crown RT 3000 Crown SC 1013 Crown SC 1016 Crown SC 3013 Crown SC 3210 Crown SC 3210-1.3 Crown SC 5310-1.3 Crown SCT 6010 Nissan AS2N1L13Q OM-Pimespo-Fiat XE 12 Simai TE80IXB Common battery sizes available – please enquire. Transport available.

Condition: excellent (used), For sale: a set of professional SK40 AD/B 6×80 tool holders according to DIN 69871 standard. The holders are in good technical condition, complete – some fitted with VHM/HSS drills of various diameters. Shank diameter: Ø6 mm Length: 80 mm Clamping type: SK40, DIN 69871 AD/B standard Condition: used, fully functional, visible signs of use (discoloration from heat). Ideal for CNC machining centers, milling machines, and precision drill presses. Nodpfxexcx Uvs Ag Djwf

Condition: good (used), safety switch, safety switch, protective grille switch -Manufacturer: Euchner, Safety Switch from vertical lathe Scherer VDZ 80 DS -Type: TZ1LEO24SR11 Nwedpfjvun Adox Ag Def .: 070828 -Technical data: see photo type plate -Dimensions: 175/110/55 mm -Weight: 1.7 kg

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, input voltage: 400 V, pressing force: 80 t, stroke length: 290 mm, operating speed: 90 mm/s, table height: 950 mm, throat depth: 1,000 mm, total length: 3,450 mm, total width: 1,820 mm, total height: 2,510 mm, overall weight: 6,800 kg, controller manufacturer: Safan, controller model: TS1, working width: 2,550 mm, bending force (max.): 80 t, back gauge travel distance R-axis: 150 mm, back gauge travel distance Z-axis: 1,000 mm, distance between stands: 2,700 mm, installation height: 1,050 mm, warranty duration: 3 months, control type: CNC control, actuation type: electric, Equipment: documentation/manual, emergency stop, foot remote control, safety light barrier, SAFAN E-Brake Press Brakes are a series of machines equipped with electric drives. Lenze servo motors, controlled by inverters from the same manufacturer, enable fast and reliable system performance over many operating hours. Additionally, the machine only consumes electrical energy during the downward stroke of the ram. The upward movement of the ram is achieved by the force of springs. During standby, the energy consumption is minimal, as there is no hydraulic pump motor maintaining pressure, unlike hydraulic press brakes. Power consumption is estimated to be up to 70% lower than with conventional hydraulic press brakes. Nwjdpfxjut S E Ne Ag Djf SAFAN E-Brake Servo-Electric Press Brake Force: 800 kN (80 tons) CNC Controlled Axes: Y1-Y2-X-R-Z1-Z2 Ram Stroke: 290 mm Open Height (Daylight): 590 mm Upper Beam Approach Speed: 90 mm/s Upper Beam Accuracy: +/- 0.01 mm Maximum Backgauge Finger Speed: 350 mm/s Maximum Backgauge Range (third reference point, X-axis): 1000 mm Hydraulic Upper Tool Clamping: WILA Connected Load: 11 kW Machine Weight: 6,350 kg Machine Width: 3,450 mm Machine Depth: 1,820 mm Machine Height: 2,510 mm Power Supply: 3/N/PE 50Hz – 400/230V Servo-electric drive (no hydraulic system) Drive transmission via belts

Condition: new, Year of construction: 2025, Manual operation with our ultrasonic cleaning technology, analogue control panel and temperature control via a digital thermostat Optional functions can be added to the PRO series. We have volumes from 60 to 7,500 L to meet all requirements. Tank capacity: 110L Außenmasse:1970x670x970mm Nodpfxof Hqavo Ag Dswf Useful dimensions grate:550x350x250mm Ultrasonic frequency: 40kHz Ultrasonic power:1000W

Condition: good (used), Year of construction: 2003, Parts cleaning device, IBS, – used - : Price per unit: €350 (net) Manufacturer: IBS Scherer GmbH Nwjdsx El A Uopfx Ag Def Model: Type F2 Year of manufacture: 2003 Serial number: 44675 Power connection: 1/N/PE 230V, 50Hz Rated power consumption: 18W, 0.2A Load capacity: 60 kg Width: 800 mm Net weight: 50 kg Drum size: 50-litre drum Frame material: sheet steel Height: 1125 mm Cleaning medium: special cleaner Cleaning tank width: 790 mm Cleaning tank depth: 540 mm Condition: good Available: immediately Location: Warehouse Frankenberg / Saxony

Year of construction: 1979, condition: not inspected (used), Feinbau lathe, automatic lathe PM1 HUC S -WKG 1269- Offered here is a lathe from the company Feinbau. Technical data: Manufacturer: Scherer-Feinbau Type: PM1-HUC-S Year of manufacture: 1979 Workpiece holder: hydraulic collet chuck Workpiece ejector: pneumatic Nwsdpfx Agshg Nl Ej Djf cross slide: 100mm feed path longitudinal slide: 80mm feed path feed type: hydraulic type of control: relay control Spindeldrehzahlen: 1400/2000/2800 total power: 4kW weight: 1000kg space requirement: 2000 x 1500mm

Year of construction: 1981, condition: not inspected (used), Feinbau Precision lathe S1-So/KA 40 -WKG 986- Offered here is a fully automatic precision lathe from Feinbau. Technical data: Manufacturer: Feinbau Type: S1- So/KA 40 Year of manufacture: 1981 center height: 134mm Swing over bed: 272mm Max. turning length: 200mm Chuck: Ø 110mm (3jaws) quill feed: 140mm (tailstock) Usage: The machine is suitable for boring or reaming cylindrical turned parts. Nwodpfx Ashg Nm Reg Dsf Accessories: Loading magazine for cylindrical turned parts 28mm Ø 40mm long. loading device Internal cooling device

Condition: used, machine/vehicle number: 1001, WP-UC 80 stainless steel bowl on stanchions for the UC 80 AC mixer Top condition Nwodpfx Ajc Upuqsg Dof

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, travel distance X-axis: 320 mm, travel distance Z-axis: 1,220 mm, spindle speed (max.): 5,500 rpm, turning diameter: 250 mm, turning height: 1,250 mm, TECHNICAL DETAILS Turning diameter: 250 mm Swing diameter: 280 mm Turning height: 1,250 mm X-axis travel: 320 mm Z-axis travel: 1,220 mm Chuck diameter: 250 mm Spindle speed: 5,500 rpm Diameter of front bearing: 130 mm Spindle bore: 65 mm Control Control system: Siemens Sinumerik MACHINE DETAILS Total power requirement: 80 kW Nwedowymvfepfx Ag Djf Weight Machine weight: approx. 17 t

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, Machine body, internal pipe system, switch cabinet and wash basket in stainless steel - Electronically controlled basket drive - level control - lid lock - Removable filter plate - weekly timer function Oil skimmer version WE AM version for additional manual cleaning - Lid with viewing window, lighting and gauntlet gloves - Low pressure pump 3- 6 bar with Brush washing device and hand gun - Compressed air blow-off gun High pressure unit 160 bar for AM version Nsdpfxof A Nquo Ag Dewf permanently installed on the machine side

Condition: used, 🧰 Product Features • Condition: Used item, see photos • Colour: grey • Material: metal • External dimensions: 124 x 83.5 x 97 cm • Load capacity: 1000 kg • Stack load: 5000 kg • Weight: 78 kg • Front side: foldable • Base: sheet metal floor with wooden insert Nedevb T Ewjpfx Ag Djwf 💰 Price €99 net, excl. VAT • Quantity discount: on request • Shipping costs: Europe-wide on request • Delivery time: Immediately available • Inspection and collection: by appointment at any time Over 5000 linear metres of pallet racking from numerous manufacturers constantly in stock (Subject to changes and errors in technical data, specifications and prices, as well as prior sale! See our terms and conditions, all prices excl. VAT ex warehouse.)

Condition: excellent (used), functionality: fully functional, bar length: 1,615 mm, bar diameter (max.): 80 mm, reverse speed: 1,000 mm/s, overall weight: 580 kg, workpiece weight (max.): 250 kg, The bar feeder was purchased in 2019 and was connected to a DMG Mori NLX 2500 / 700. The bar feeder was hardly used. TECHNICAL DETAILS Connector: Harting Material Cross-Sections Round: 5 to 80 mm Square: 5 to 50 mm Hexagonal: 5 to 60 mm Bar Lengths Bar length: 500 to 1,615 mm Short bar length: 90 to 500 mm Performance Data Magazine capacity: 250 kg Bar changeover time: 30 s Feed rate: 0 to 500 mm/s Return speed: 1,000 mm/s MACHINE DETAILS Nwjdjy A Rlpepfx Ag Dsf Connection voltage: 230/400 V Control voltage: 24 V Power consumption: 2 kW Dimensions & Weight Weight: 580 kg Bar pusher travel: max. 1,710 mm Loading axis height: 905 to 1,252 mm EQUIPMENT Short bar kit Handheld control unit Remote control Safety covering Fixed protective grilles

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram Nwedpfx Aox A U Ncjg Dsf o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: new, Year of construction: 2025, functionality: fully functional, turning diameter over cross slide: 650 mm, spindle bore: 106 mm, turning length: 2,130 mm, turning diameter: 650 mm, quill stroke: 150 mm, quill diameter: 100 mm, rapid traverse X-axis: 13 m/min, rapid traverse Z-axis: 13 m/min, spindle speed (min.): 30 rpm, spindle speed (max.): 1,600 rpm, center height over cross slide: 410 mm, feed rate X-axis: 2 m/min, feed rate Z-axis: 13 m/min, total length: 4,290 mm, total width: 2,553 mm, total height: 2,375 mm, type of input current: three-phase, spindle motor power: 11,000 W, overall weight: 5,200 kg, rotational speed (min.): 30 rpm, rotational speed (max.): 1,600 rpm, torque: 1,050 Nm, controller manufacturer: Milltronics, controller model: 9000 DGI, input voltage: 400 V, drill spindle diameter: 106 mm, nominal power (apparent): 20 kVA, number of spindles: 1, spindle nose: A1-11, tailstock quill diameter: 100 mm, tailstock quill mount: MK 5, tailstock quill stroke: 150 mm, number of slots in tool magazine: 8, Equipment: rotational speed infinitely variable, LIST PRICE of the machine: EUR 119,500.00!!!!! The machine is immediately available and NEW. Delivery of the machine in overseas packaging from our warehouse. (Transport of the machine at the buyer’s expense) Operating materials to be provided by the buyer. Commissioning and training by Milltronics: EUR 5,000.00 Leasing possible (subject to creditworthiness) Machine Details: • CNC control Milltronics 9000-DGI • 15" LCD color touchscreen • Ethernet interface • USB interface • Productivity software, DSA, MSV, bidirectional turning cycle, 9000-DGI Desktop • Connection for external keyboard • Electronic handwheels for manual operation, teaching, or automatic sequences • Custom macros available • Override potentiometers for axes and spindle • Spindle load monitoring • Key switch to lock EDIT function • Lights to indicate operating status • Additional “M” function with CNC wait channel • Constant cutting speed • Rigid tapping • Spindle speed 30 – 1,600 rpm • Spindle motor 18 / 11 kW, 2-stage electronic gearbox • Spindle nose type A1-11 • Tool turret with 8 positions 25 mm • One axial tool holder for standard tools 25 mm x 25 mm • One tool holder for boring bars 38 mm • Automatic lubrication system • Full enclosure with sliding doors • Coolant system with pump • CE certification • Instruction manual, spare parts list and circuit diagrams in digital format • Operating manual and maintenance manual in digital format • Transformer for standard industrial power supply 400 volts, 3 phase • Lifting brackets for crane transport Nwodey Hqhfepfx Ag Dsf Optional accessories: Manual 3-jaw chuck 300 mm Hydraulic tailstock quill (only in combination with hydraulic chuck) Hydraulic 3-jaw chuck with hydraulic unit (diameter 300 mm – bore 70 mm) Fixed steady rest with rollers, range 20 – 200 mm Fixed steady rest with rollers, range 180 – 410 mm Travelling steady rest with brass pads, range 20 mm - 200 mm 38 mm boring bar holder for turret 25 mm axial tool holder Hinged belt chip conveyor instead of drawers Programming manual in paper format Machine manual in paper format Foot mat with Milltronics logo

Condition: used, Year of construction: 2001, Amada HFE 80-25 SL Hydraulic Press Brake. S/No. VO11137 (2001), Remanufactured JTES 2018 Nwodpjy D Rhyofx Ag Djf Location: These lots are located in Yeovil, UK. Please Note: There are no loading facilities on site, dismantling and loading will be at the cost of the purchaser.

Condition: used, Year of construction: 2022, Bystronic Xpress 80/2100 Hydraulic Press Brake. S/No. Xpress 22334EU (10/2022), Max Press Force 800KN, Max Working Length 2100mm, Max Stroke 200mm, Machine Weight 6000kg Location: These lots are located in Yeovil, UK. Please Note: There are no loading facilities on site, dismantling and loading will be at the cost of the purchaser. Nwodpsy D Rbaofx Ag Def

Condition: new, The double-sided cantilever rack by BLT, with a height of 315 cm, is ideally suited for storing medium-weight long goods such as profiles, pipes, and bars in warehouses, workshops, or craft businesses. With an approximate rack length of 5.12 m, a usable depth of around 80 cm, and a total of 5 levels per side including the base level, this cantilever rack offers clearly arranged and easily accessible storage space for long and bulky items on both sides. Each cantilever arm can support up to 500 kg, and each upright can handle up to 1,800 kg per side. The bolt-on cantilever arms with deflectors ensure robust and practical use in day-to-day operations. Made in Germany. Freight within Germany already included, plus VAT. Product details: Nedpfx Agjy Hirps Dswf - Rack type: Double-sided cantilever rack - Height: approx. 315 cm - Length: approx. 5.12 m - Total depth: approx. 174 cm - Bay width: approx. 128 cm - Cantilever arms: approx. 80 cm usable length (IPE80) - Usable depth of base level: approx. 80 cm - Load per arm: max. 500 kg (with even load distribution) - Load per upright: max. 1,800 kg per side (without base level, with even load distribution) - Levels per side: base + 4 storage levels (5 levels per side total) - Design: Double-sided, bolt-on cantilever arms with deflectors - Upright profile: IPE140 - Cantilever arm profile: IPE80 - Colour finish: RAL 7016 - Manufacturing: Made in Germany - Delivery: Freight within Germany included, plus VAT Scope of delivery: - 5 × uprights made from IPE140, height approx. 3,150 mm - 40 × cantilever arms, approx. 80 cm length, made from IPE80 - Including mounting hardware - Including heavy-duty anchors for floor fixing Advantages of the BLT cantilever rack: - Ideal for storing medium-weight profiles, pipes, and bars - Double-sided design for storage space accessible from both sides - Bolt-on cantilever arms with deflectors - 5 levels per side, including base, for optimal use of storage space - Up to 500 kg load capacity per arm and up to 1,800 kg per upright per side - Secure floor anchoring with supplied heavy-duty anchors - Made in Germany - Freight within Germany included Delivery: - Freight within Germany included - Delivery includes mounting hardware - Secure floor anchoring with supplied heavy-duty anchors Enquiries & custom planning: Take advantage of our personal consultation for your individual storage solution. Inform us of your required dimensions, stored goods, and available space. Our experienced consultants are happy to provide you with a non-binding offer featuring custom planning and structural calculation for your bespoke cantilever racking system. Use our enquiry list or contact us directly by phone. Together, we will plan your tailor-made racking system.

Condition: new, Year of construction: 2022, 28.55 rm. Wide span shelving 80 cm deep , Workshop shelving , Storage shelving , Large shelving , Manual storage , Shelving , Small parts storage Data : - Height : approx. 200 cm - Depth : approx. 80 cm - Length : approx. 28.55 running meters Shelf offer consisting of: - 16 x frame approx. 200 x 80 cm, disassembled. - 90 x crossbar approx. 185 cm. - 45 x support shelf approx. 184.5 x 79.5 cm. - 90 x beam / load distributor. - Incl. safety pins - Model : BLT , Type WR20/80 - Load: 400 kg shelf load, with evenly distributed load. - Levels: 3 x storage levels. - Chipboard, natural. - Uprights blue. - Galvanized beam - New from stock. - other quantities available! We can pre-assemble the frames for a small surcharge of 6€/net per piece. Nwsdpfx Aey Hibwjg Def -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 2887,00 € net plus legally valid VAT. You will receive an invoice with VAT shown. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, Year of construction: 2022, 13.35 rm. Wide span shelving 80 cm deep , Workshop shelving , Storage shelving , Large shelving , Manual storage , Shelving , Small parts storage Data : - Height : approx. 200 cm - Depth : approx. 80 cm - Length : approx. 13.35 running meters Shelf offer consisting of: - 08 x frame approx. 200 x 80 cm, disassembled. - 56 x traverse approx. 185 cm. - 28 x support shelf approx. 184.5 x 79.5 cm. Njdpfsy Hibqsx Ag Djwf - 56 x beam / load distributor. - Incl. safety pins - Model : BLT , Type WR20/80 - Load: 400 kg shelf load, with evenly distributed load. - Levels: 4 x storage levels. - Chipboard, natural. - Uprights blue. - Galvanized beam - New from stock. - other quantities available! We can pre-assemble the frames for a small surcharge of 6€/net per piece. -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 1724,00 € net plus legally valid VAT. You will receive an invoice with VAT shown. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, Year of construction: 2022, 57 running meters Wide span shelving 80 cm deep , Workshop shelving , Storage shelving , Large shelving , Manual storage , Shelving , Small parts storage , Data : - H : approx. 200 cm - D : approx. 80 cm - L : approx. 57 running meters Shelf offer consisting of: - 031 x frame approx. 200 x 80 cm, disassembled. - 240 x traverse approx. 185 cm. - 120 x support shelf approx. 184.5 x 79.5 cm. - 240 x joist / load distributor. - Incl. safety pins - Model : BLT , Type WR20/80 - Load: 400 kg shelf load, with evenly distributed load. - Levels: 4 x storage levels. Nwodoy Hia Hepfx Ag Dof - Chipboard, natural. - Uprights blue. - Galvanized beam - New from stock. - other quantities available! We can pre-assemble the frames for a small surcharge of 6€/net per piece. -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 7267,00 € net plus legally valid VAT. You will receive an invoice with VAT shown. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, Year of construction: 2022, 57 running meters Wide span shelving 80 cm deep , Workshop shelving , Storage shelving , Large shelving , Manual storage , Shelving , Small parts storage Data : - Height : approx. 200 cm - Depth : approx. 80 cm - Length : approx. 57 running meters Shelf offer consisting of: - 031 x frame approx. 200 x 80 cm, disassembled. - 180 x traverse approx. 185 cm. - 090 x support shelf approx. 184.5 x 79.5 cm. - 180 x joist / load distributor. - Incl. safety pins - Model : BLT , Type WR20/80 - Load: 400 kg shelf load, with evenly distributed load. Nwedpfxjy Hiayj Ag Djf - Levels: 3 x storage levels. - Chipboard, natural. - Uprights blue. - Galvanized beam - New from stock. - other quantities available! We can pre-assemble the frames for a small surcharge of 6€/net per piece. -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 5737,00 € net plus legally valid VAT. You will receive an invoice with VAT shown. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.