Used Kg Wetter Angle Grinder for sale (67,465)

Condition: good (used), Year of construction: 2011, operating hours: 40,000 h, functionality: fully functional, pressing force: 88 t, filling opening width: 990 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, overall weight: 23,000 kg, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 643 m³/h, Good day, We hereby offer, subject to prior sale, a used baler including conveyor belt, wire tying stations, and bale chute from the manufacturer HSM GmbH + Co. KG, model VK 8818 FU. Ljdpfoymmtcsx Am Noaa The following technical specifications were taken from the manufacturer's operating manual and brochures; we do not assume any liability for the correctness or completeness of this information. Manufacturer: HSM GmbH + Co. KG, Germany Model: VK 8818 FU Year of manufacture: 2011 Operating hours: approx. 40,000 hours as of July 2025 Main press force: 880 kN Specific press force: 107 N/cm² Feed opening dimensions: 990 x 1,800 mm Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Tying: 5-fold horizontal, fully automatic Baler dimensions (set up): 12,130 x 4,800 x 3,270 mm (L x W x H) Overall installation dimensions with conveyor system: 14,000 x 23,000 x 7,745 mm (L x W x H) Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The press is in good condition and will be replaced with a new, larger press in May/June 2026. Until then, the machine can be inspected in operation with material. We would be pleased if this baler is of interest to you. Your Mertens & Frowein GmbH service team

Year of construction: 2019, condition: ready for operation (used), A mixing vessel KG Bremen and two stirrers PRG and IKA are available. 1) Mixing vessel KG Bremen, year of manufacture: 2019, max. operating pressure: atmospheric, max. operating temperature: 80°C, volume: 1150L, max. double-jacket operating overpressure: 5bar, max. double-jacket operating temperature: 80°C, material: 1.4301. 2) Precision stirrer PRG R112M-6, year of manufacture: 2004, agitator length: 930mm, impeller diameter: 160mm. 3) Precision stirrer IKA RF 04-T-1085, year of manufacture: 1999, total length: 1100mm, impeller diameter 1/2: 160mm/200mm. An on-site inspection is possible. Laedpfx Amjxhntro Nea

Condition: like new (used), functionality: not functional, load capacity: 6,500 kg, Load capacity 6500 kg Please note: Arm diameter adjustable from 1880 mm to 4550 mm (swivel-out) Laedjx Thucjpfx Am Noa Space-saving and continuously adjustable, the extension arms can be locked in place Speed continuously adjustable from 0.001 to 5 rpm Motor power 3 kW Torque 15000 Nm Height 800 mm Maximum current transmission 2000 A Weight 4700 kg with hand and double-foot remote control CE certificate, declaration of conformity, documentation, circuit diagram with original 2016 quotation invoice Current new price approx. €28,000

Condition: excellent (used), For sale: professional cutter and drill bit sharpener, model PP U3. Condition: very good, complete unit ready for operation. Included in the set: • Set of grinding wheels • Adjustable angular tool holder • Workshop lamp with flexible arm • Keys and clamping elements Specifications: Lajdpfx Aexdh Hqjm Noa • For sharpening cylindrical and spiral end mills • For sharpening step and cylindrical drills • Wheel linear speed up to 35 meters per second • Maximum noise level: 66 dB • Machine weight: 41 kg Solid, stable construction—ideal for precise tool machining. A reliable solution for tool rooms, CNC workshops, and machine shops.

Condition: used, Year of construction: 2015, Recycling system for recovering and separating plastic and rubber products from textile reinforcements, such as various types of rubber hoses, PVC, tarpaulins, banners and other plastic materials in which textile reinforcement occurs. The system cooperates with a granulation group and a separation system. Hourly capacity: 50 - 80 kg/h Infeed dimensions: 270 x 120 mm + fi 80 mm Blade length: 3x2 + 2x2 Rotor diameter: 250 mm Lodpfxewpkw Ej Am Njaa Cutting length: 600 mm Engine power: 22 kW Dimensions: 3200 x 3000 mm Height: 2500 mm Weight: 1000 kg Year of production: 2015 Technical condition: used machine, all engines in working order. No top cap with dimensions: 400x300 mm used for loading the product. Full and original technical documentation available. .

Condition: used, Year of construction: 2000, machine/vehicle number: P18096N, functionality: fully functional, pressing force: 20 t, stroke length: 160 mm, total height: 2,150 mm, overall weight: 180 kg, Good day, We hereby offer you, without obligation, a used workshop press from Rodcraft, model WP 20F. Manufacturer: Rodcraft Pneumatic Tools GmbH & Co. KG Model: WP 20 F Year of manufacture: 2000 Machine No.: P18096N Hydraulic stroke: 160 mm Pressing force: 20 t Machine dimensions: 2150 x 960 x 660 mm Transport dimensions: 2150 x 980 x 750 mm Machine weight: 180 kg Note: Ljdoygm N Djpfx Am Nsaa The above technical data has been taken from the manufacturer’s brochures or other sources, for which we cannot guarantee the accuracy or completeness. Scope of delivery: 1 unit used workshop press Rodcraft, type WP 20F Application area and condition: The machine was occasionally used in an industrial metalworking shop for pressing out bearings, etc. The machine is fully functional and in good condition. We would be pleased if this machine is of interest to you. Your service team at Mertens & Frowein GmbH

Condition: excellent (used), Bezel (28388) Lasdpfx Amemkfd So Nja SPH 360 mm Weight 37 kg Dimensions, see drawing

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, power: 9.7 kW (13.19 HP), Technical data cardboard shredder: Manufacturer Presto GmbH & Co. KG Ledpfxou Tha Ij Am Noaa Type PZA Year of construction 2007 Throughput volume 130 m³/hour Speed 37/9 rpm Motor power 7,5 / 2,2 kW Electrical connection 32 A Dimensions shredder inside 1,490 x 1,320 x 530 mm (L x W x H) Dimensions shredder outside without cover 2,308 x 1,320 x 685 mm (l x w x h) Machine weight 0,45 tons Use of the systems: The PZA cardboard shredder was in use in a Dutch logistics centre to pre-shred loose, erected cardboard boxes from the returns department and then press them into bales. The cartons were fed manually onto the infeed conveyor and transported directly to the cardboard shredder by a sliding belt conveyor and shredded. The pre-shredded cardboard boxes were then transported over hundreds of metres to the baler where they were pressed. Scope of delivery: 1 piece Presto cardboard shredder (2-shaft shredder) type PZA Comments: The cardboard shredder was an elementary part of the disposal line and therefore good maintained to ensure high availability of the returns department. The machine is in good condition and ready for immediate use. The price is per piece exw. our warehouse in Siddeburen, the Netherlands. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: fully functional, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Ljdpeu Thh Eofx Am Nsaa Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating instructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2003, condition: good (used), functionality: fully functional, machine/vehicle number: 03234, 6 Brush ( 3 pairs) descaling machine for steel wire size 5.5mm - 16.0 mm max (low carbon) Brush pairs arranged in a 60 degree offset for maximum effect. A very clean looking machine. On site viewing and inspection recommended Lajdpfxsx R Uzds Am Nsa

Condition: excellent (used), KOLBE MWE52 MIXER GRINDER Will produce up to 1700 kg/h of product Laedpfx Amjx Swxbe Noa

Condition: excellent (used), Heavy duty wooden pallets with 3 skids Laodpfx Ajl Uvv Tem Nja accessible from 4 sides length 1680 mm width 1250 mm board thickness 45 mm weight 82,5 kg several available

Condition: used, Year of construction: 1979, machine/vehicle number: Res BS, Demag PK2 Chain Hoist Crane Lifting Unit 250kg / 500kg Approx. 40 units available!!! 250kg / 0.25t rated load / lifting capacity – single fall – 500.- 500kg / 0.5t rated load / lifting capacity – double fall – 600.- With 2 lifting speeds, lifting height approx. 3-4m Complete with pendant control and load hook Total weight approx. 40kg, 380V 50Hz connection Ljdpfsvzkylsx Am Njaa Top condition, fully functional. Not a worn or used device! Connect and start operating. Comes from ongoing operations Item location: 75053 Gondelsheim See pictures

Condition: good (used), Year of construction: 2024, Welding turntable KT 300 Load horizontal 300 KG, tilted 150 KG Power consumption 220V, 50 Hz table diameter 450mm height 500mm Tilt range stepless via crank gear motor 0 - 90°. speed 0,3 - 2,5 rpm Laedpfx Aebvk I Ejm Nsa Incl. foot remote control Surcharge: Quick release - jaw chuck diameter 300mm, 450.-€

Condition: new, Year of construction: 2024, load capacity: 300 kg, Equipment: foot remote control, rotational speed infinitely variable, Protec KT 300 H welding turntable, 170/400 special version Horizontal load 300 kg, tilted 150 kg Power consumption 220 V, 50 Hz Table diameter 450mm Lsdpsvbrqxofx Am Njaa Hollow shaft diameter 170mm Table height 500mm Welding current transmission 400 A Quick-action chuck diameter 300mm, surcharge 550.-€ Quick-action chuck diameter 400mm, surcharge 750.-€ Crank gear motor 0 - 90° stepless adjustment Infinitely variable speed 0.01 to approx. 5 rpm. incl. foot remote control Digital display with welding time limiter (if required)

Condition: new, Year of construction: 2025, functionality: fully functional, load capacity: 1,000 kg, table load: 1,000 kg, 3-axis turning and tilting positioner with 1000 kg load capacity, clamping plate diameter 0.65 meters Height adjustment 1000 - 1500 mm Suitable for welding, assembly, processing, etc. With its stable and robust construction, flexible positioning via three axes including overhead, and user-friendly operation, it facilitates welding, assembly, and handling of large workpieces. Optimal positioning of the workpiece improves welding quality and allows higher specified loads in any position. Thanks to the endless rotation of the two rotary axes and additional height adjustment, all workpiece positions (including overhead) are possible. Turntable speed infinitely adjustable from 0.1 to 1.0 rpm. With wireless remote control Rotation range 360° infinite Swivel range 360° infinite Lift: 1000 - 1500 mm Laedpfexbh Dqox Am Nea Arm outreach radius: 1 meter

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Lajdpfx Aox A U Ncsm Nsa Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: reconditioned (used), Year of construction: 2014, operating hours: 5,612 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total height: 2,800 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), volume flow: 332 m³/h, Technical information baler: Lodpfxovtpq He Am Nsaa Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,612 hours, stand August 2025 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press was partially overhauled and tested in our workshop, see photos and our function video. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: used, Year of construction: 2018, functionality: fully functional, volume flow: 10.2 m³/h, input voltage: 230 V, USED VACUUM PUMP Technical data Max. pumping speed 50 Hz (mbar) 8.9 m3/h Max. pumping speed 60 Hz (cfm) 6.0 cfm Ultimate vacuum 2 x 10-3 mbar / 1.5 x 10-3 torr Ultimate vacumm with gas ballast 1 x 10-2 mbar / 0.75 x 10-2 torr Ultimate partial vacuum without gas ballast 4 x 10-4 mbar / 3 x 10-4 torr Water vapor tolerance 40 mbar / 30 torr Number of stages 2 Permissible ambient temperature range (operation) 15 - 40 °C Laedew Rqx Dopfx Am Nja Permissible ambient temperature range (storage) -10 - 60 °C Max. outlet pressure (abs.) 1.1 bar Oil capacity min./max. 0.45 / 0.85 l Inlet connection small flange KF DN 25 Outlet connection small flange KF DN 25 Rated motor power 0.30 kW Rated speed 50/60 Hz 1500/1800 min-1 Protection class IEC 60529 IP 40 Dimensions (L x W x H) 503 mm x 156 mm x 240 mm Weight 24.8 kg Noise (sound pressure level) in dBA at 50 Hz or 1500 rpm/62% (VARIO)/1500 rpm (VARIO-SP)/12500 Upm (VACUU·PURE®) - 52 dBA NRTL certification - No

Condition: new, Year of construction: 2025, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 600-700 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: Lsdpfx Amendn Agj Noaa - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2026, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Laedpfx Aeng Exaem Nea Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 800-900 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Year of construction: 2008, condition: good (used), Machine type: Finishing machine Manufacturer: Supfina Grieshaber GmbH & Co. KG Model: 622/1 Serial number: 760001 Year of manufacture: 2008 Available immediately Ex site for self disassembly Lasdpfx Amslrt Sao Nsa Optionally we can offer dismantling and loading

Condition: good (used), Year of construction: 1973, machine/vehicle number: 73040, Embossing press Baier GEBA 1/F, installation height 90 mm, pressure capacity 800 kg, working size 10cm x 14 cm, built in 1973, machine number 73040, in good condition, immediately available If you are interested, we would be happy to inform you about other machines in our company. You are welcome to view the machine in our company by prior appointment. Laedpfx Asvt Rpqjm Nsa

Condition: excellent (used), Year of construction: 2006, operating hours: 1 h, functionality: fully functional, K+G Wetter VCM 120 STL Condition like new, used only few times to try. The blades are never sharpened, in factory installed. Everything works. Laedpfx Asxpwc Som Nsa Machine length 2400 mm Machine width 2250 mm Machine height 1780 mm Machine weight 1650 kg Bowl Volume 120 liters

Year of construction: 2025, condition: new, Maintenance-friendly dedusting system specially developed for aggressive sandblasting dusts with pre-chamber impact separator, complete Ljdjlxyhfjpfx Am Nsaa essentially consisting of: a) 1 cartridge dry filter, type PF 1.4.B62.00 5000m³/h (other sizes available) each consisting of a stable, vacuum-tight 3 mm sheet steel housing, divided into the raw gas chamber with filter cartridges, filter pre-chamber impact separator and clean gas chamber with filter cleaning by means of compressed air, each with separate Easy Open maintenance door. Dust collection hopper with slotted valve for dust disposal using big bags. Solenoid valve control with differential pressure display for optimum adjustment of the filter cartridges - cleaning. Maintenance doors as swing doors Maintenance easy.