Used Veb Agitator for sale (790)

Year of construction: 1977, condition: good (used), 2 units of emergency power generators, East Germany (GDR) Engine manufacturer: VEB SKL Magdeburg, GDR Type: 8NVD26 A2 Year of manufacture: 1977 Continuous power: 294 kW Maximum power: 323 kW Displacement: 52.96 liters Compression ratio: 14 Speed: 750 rpm Specific fuel consumption: 224 g/kWh Lrjdpfxeigyt Hj Aa Ror Fuel consumption in 8 hours: 640 liters Boost pressure ratio: 1.38 Charge air temperature after turbocharger: 60°C Generator: Manufacturer: VEM Dessau Type: SSED 509-8a Voltage: 400 volts Electrical power: 330 kVA Power factor (cos. φ): 0.8 Dimensions: Length 4270 mm, Width 1516 mm, Height 2030 mm Total weight approximately 8500 kg per unit !! Further information available only by telephone !!!

Condition: good (used), Item: D-2139-Vaccum Pump-DVI100 Vacuum Pump DVI100, capacity 100 m3, working condition! Ljdpfx Aoh A Hcvoa Rorr

Year of construction: 1975, condition: good (used), functionality: fully functional, drive type: Diesel 130 Kw, Patrol boat from the former GDR, later used by the Berlin Water Police (WSP 1), IFA 6-cylinder diesel engine. Winter-capable, icebreaker rating up to 3 cm thickness, certified for all waters including open sea. Dimensions: 11.90 m length, 2.90 m beam, draft 0.90 m. Top speed: over 30 km/h. Engine: Schönebeck 6-cylinder, 4-stroke diesel, type DM 6 VD 14.5/12-1. According to research, the engine delivers either 170 or 220 HP from 10 L displacement. These engines are known for low fuel consumption: at canal cruising speeds (8–12 km/h), consumption is 6–8 L per hour. Equipment includes signal mast, mast spotlight, boat lighting. Dual helm positions: inside cabin and flybridge. AGM batteries, engine start with 24 V system, 12 V onboard network. Brand new onboard toilet. Electric and manual bilge pumps (automatic/manual operation). Complete overhaul from 2021 to 2023: 5-layer primer and 3-layer antifouling coating. Steel hull, aluminium superstructure. New electrical wiring, new exhaust system, new clutch, engine overhauled, fuel tank serviced, new lines installed, new air filter. Lodpey D Rk Iofx Aa Rjrr Engine starts and runs flawlessly, forward and reverse gear shifts without issues. Some work is still required to complete comfort features. The vessel is suitable as a small tugboat or as a work or fishing boat. Lower helm station: the gauges still need to be installed; required instruments and switches are included.

Condition: used, functionality: fully functional, machine/vehicle number: D20E/8022, Offer Number: D20E/8022 Machinetype: multiple wire drawing machine - dry Info: straight through Make: VEB Type: 8 Block Constr. year: inlet wire diameter: 2,5 mm finished wire diamter: 0,8 mm Ledpjwi Tidjfx Aa Rjrr number of drafts: 8 diameter of capstan: 400 mm speed -meters/sek: 15 m Location: Europe

Condition: used, turning length 600 mm turning diameter over bed 360 mm turning diameter over slide rest 190 mm bed width 295 mm number of spindle speeds 45 - 2240 U/min. spindle bore 33,0 mm tailstock quill taper MT MK 3 feed Längs 0,02-0,8 mm/U feed Quer 0,0125-0,5 mm/U total power requirement 5,5 kW weight of the machine ca. 1900 kg range L-W-H 2050 x 950 x 1280 mm Refurbished and repainted in 2013 Costs around 16.000 euros Furnishing: - WNW NILES 3-jaw chuck Ø 200 mm - Multifix steel holder size B with inserts Lrsdpexaamusfx Aa Rsr - revolving center points - chuck key - Movable tailstock - Operation manual

Condition: used, diameter M5/M64 mm weight / kg Type / 0 different types available: tapping head GB2 - 150 Euro tapping head GB3 - 250 Euro Lrsdpfxsiwpure Aa Rsr tapping head GB5 - 450 Euro

Condition: ready for operation (used), machine/vehicle number: 251, Initial speed: 31.5 rpm Output power: 0.37 kW Electrical connection: 220/380 V Space requirement: 200 x 200 x 490 mm Weight: 15 kg with HEIDENHAIN rotary encoder Lrjdpfxsd Avb Do Aa Rjr

Condition: excellent (used), machine/vehicle number: 043700 001 7, Starting speed: 31.5 rpm Rated power: 0.37 kW Electrical connection: 220/380 V, 1.9/1.1 kW Lsdpfod Avbxex Aa Rerr Space requirement: 200 x 200 x 490 mm Weight: 15 kg with rotary encoder HEIDENHAIN

Condition: excellent (used), functionality: fully functional, WMW Germany GFL-400 x 1000 mm Thread Milling Machine Manufacturer: WMW (Germany) Model: GFL-400 Centre Height: 205 mm Maximum Workpiece Length: 1000 mm Maximum Workpiece Diameter over Cross-Slide: 200 mm Maximum Swing Diameter over Bed: 400 mm Cutter Speeds: 55 rpm to 250 rpm Maximum Cutter Diameter: 100 mm Spindle Bore: 80 mm - Suitable for thread milling, worm milling, and spline milling. Ljdpoytirnofx Aa Rorr - Also capable of gear hobbing and spline hobbing. - Supplied complete with change gears, index plates, arbors, and additional accessories. - The machine is in excellent working condition.

Condition: used, Hand lever shears VEB Scherenbau Nossen type ScDH10 Blade length: 180 mm Sheet thickness: max. 10 mm Flat material: 50x15 mm square solid material: 22x22 mm Round steel: 24 mm Angle steel: 60x7mm T-steel: 60x7mm Lsdpouqrabsfx Aa Rorr on mobile base frame Own weight: approx. 150 kg

Condition: good (used), Year of construction: 1983, machine/vehicle number: 7486, functionality: fully functional, spindle mount: MK 2, total width: 480 mm, total length: 620 mm, total height: 1,295 mm, overall weight: 165 kg, spindle speed (max.): 2,800 rpm, spindle speed (min.): 450 rpm, stroke length: 100 mm, Solid bench drilling machine for individual or series production in good condition (used). Lrsdpjwgfkuofx Aa Rer

Condition: excellent (used), functionality: fully functional, travel distance X-axis: 2,000 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 2,000 mm, table load: 6,000 kg, spindle diameter: 110 mm, spindle speed (min.): 5 rpm, spindle speed (max.): 1,120 rpm, total height: 4,300 mm, total length: 7,200 mm, total width: 4,600 mm, table length: 1,600 mm, table width: 1,400 mm, feed length W-axis: 800 mm, type of input current: AC, spindle stroke: 800 mm, overall weight: 26,000 kg, year of last overhaul: 2020, A Union Gera BFT 110/6 horizontal boring mill is for sale The machine was built around 1980 and was overhauled by us in 2009/2010 and has been in our care since then. The scope of the overhaul includes the following: - Electrical system almost completely renewed - New control cabinet incl. Siemens S7-200 PLC control system - New drive technology Siemens Simodrive 611, feed motors Siemens 1FK7 - Heidenhain TNC 124 line control + electronic handwheel - Heidenhain length measuring systems on X, Y and Z axes - Heidenhein angle measuring device in B-axis (rotary table) - Spindle drive three-phase asynchronous with DC brake electronics - Renewal / overhaul of all hydraulic components - New KGT in X and Y axes - Overhaul of the drive systems of all feed axes - All axles were rescraped - Lubrication systems of axes and headstock overhauled - New bearings and overhaul of the gear components of the headstock For further technical details see photos or on request. Equipment of the machine: - Heidenhain TNC 124 line control + electronic handwheel - Facing slide (U-axis) - Electric tool clamp SK 50 The sale is due to capacity reasons. The machine is fully functional and immediately available. It achieves production accuracies according to the manufacturer's protocol. Technical documentation is available. The machine is fully functional and, by prior arrangement, can be inspected under power. The offer is subject to our terms and conditions of business and delivery. Subject to errors and prior sale. As a warranty is excluded for the purchase of used machines, we recommend that our Lodpfx Asu U Hvwsa Rjrr our customers to inspect the machine before making a purchase. As is customary with used machines, payment is made by bank transfer before delivery of the goods. bank transfer. Dismantling, relocation, installation, commissioning and geometric adjustment at the new location, can be carried out by us on request. We will be happy to submit a separate offer for this. Delivery of the machine to other EU countries is also possible on request.

Condition: used, VEB Polygraph 882/2-18 gathering machine Ledpfxsx Ab Nco Aa Rerr 18 gathering stations Features suction feeding 3-phase power, requiring 2-10 kW of power consumption at 440 V

Condition: used, Used Charles Thompson model CT400 Hastelloy C22 Mobile Agitated Nutsche Filter Dryer Manufacturer: Charles Thompson Limited, UK Model: CT400 Type: Mobile agitated Nutsche filter/dryer Year: 2001 Filter diameter: approx. 400 mm / 15.7 in Filtration area: approx. 0.125 m² / 1.35 ft² Product-contact material: Hastelloy C22 External/jacket: 316L stainless steel Shell design: 3 bar/full vacuum Jacket design: 3 bar/full vacuum Lrsdpfx Aaozun Hls Rsr Design temperature: -30°C to +100°C ASME: Section VIII Div. 1 (1998) + A99 Empty weight: 570 kg / 1,257 lb Agitator: single-blade, approximately 0.75 kW Agitator lift: hydraulic raise/lower Configuration: jacketed vessel on mobile stainless frame/casters.

Condition: like new (used), Year of construction: 2020, functionality: fully functional, tank capacity: 5,000 l, usable tank capacity: 5,000 l, total height: 3,225 mm, outer diameter: 1,756 mm, overall weight: 1,640 kg, wall material: stainless steel, wall thickness: 8 mm, wall structure: single-walled, manhole diameter: 610 mm, manhole location: top, operating temperature: 100 °C, negative pressure: 100,000 Pa, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, sanitary facilities, Brand new, never commissioned. Professionally decommissioned from an INEOS manufacturing facility prior to first use. Manufactured by Able Engineering, this high-specification sanitary 316L stainless steel agitated pressure vessel is suitable for pharmaceutical, cosmetics, personal care, food, beverage and fine chemical applications. Designed for vacuum and low-pressure service and suitable for installation within ATEX-rated environments. Constructed entirely in 316L stainless steel throughout with 8mm shell and dish walls, dished top and bottom heads, heavy duty tubular stainless steel leg supports with bolt-down base plates and load cell arrangement, hygienic internal finish < 0.8 Ra, and full hygienic ferrule fittings throughout conforming to ASME BPE / BS3062. Suitable for CIP. Material: 316L Stainless Steel throughout. Working Volume: 5,000 Litres. Shell ID: 1,740mm. Overall Height: 3,225mm. Shell & Dish Wall Thickness: 8mm. Design Pressure: -1.0 to +0.45 Bar.G. Design Temperature: -10°C to +100°C. Empty Weight: 1,640kg. Design Code: PD5500:2018, Cat.3. PED 2014/68/EU certified. Manufacturer: Able Engineering. Serial Numbers: PXL19635-1, PXL19635-2, PXL19635-3. Factory Tested: September 2020. Fitted with SEW-Eurodrive geared agitator with double mechanical seal, seal pressure pot, and reinforced agitator mounting. Nozzles and fittings include 610mm hinged manway, CIP inlet with dip pipe and TOD clip-on spray fitting, pressure relief valve connection, nitrogen blanketing connection with pressure indicator, Endress & Hauser hygienic thermowell, dual flush polished level switches, load cell arrangement on support legs, lifting lugs, and earthing boss. Three units currently available, all brand new and never commissioned, sourced directly from the same INEOS facility. Tank saddles available on request for either single use or purchase. Please view our other listings for additional sizes and configurations — all stock is brand new, ex-INEOS, and available for immediate inspection and purchase. Lrsdpfxjzhnlzo Aa Ror Original engineering drawings and full nameplate documentation available on request. Inspection welcome by appointment. Loading and transport can be arranged. Tracht Ltd specialise in hygienic process equipment for the food, beverage, cosmetics, pharmaceutical and chemical industries, with practical experience supporting both batch and continuous manufacturing environments. In addition to process vessels, Tracht Ltd supply and install stainless steel mixing vessels, Silverson high-shear mixers, hygienic lobe pumps, hygienic centrifugal pumps, access gantries, and provide full vessel installation and commissioning services. Whether replacing existing equipment or expanding production capacity, Tracht Ltd can specify, supply and install the right equipment for your application. Please contact us for further information or to discuss delivery and installation options.

Condition: used, Used BCD Engineering Ltd stainless steel vertical reactor body. Approximately 4,000 litre nominal capacity. Unit measures approximately 1,800mm diameter x 1,700mm straight side. Has welded dished top and bottom heads. Internal rated 10 bar / full vacuum design pressure at -29 to 200 deg.c. External stainless steel coil jacket rated approximately 324 litre capacity, 6 bar / FV design pressure at -29 to 200 deg.C. Unit includes top mounted stainless steel anchor type agitator but no drive/gearbox currently fitted. Unit mounted on side support lugs. Lodjzimv Iopfx Aa Rjrr

Condition: used, mileage: 490,194 km, power: 375 kW (509.86 HP), first registration: 01/2023, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, color: white, gearing type: automatic, emission class: euro6, Equipment: ABS, air conditioning, navigation system, parking heater, soot filter, Volvo FH 500 Globetrotter XL VEB+ ADR + PTO * German vehicle * EURO 6 E * VEB+ engine brake * Leaf/air suspension * XL cab * I-Park Cool (stationary air conditioning) * Auxiliary heater (parking heater) * 2 beds * Refrigerator * ACC adaptive cruise control * Turn assist system * Emergency brake assist * Roof hatch * Dual fuel tank system * Navigation * Roof and side flaps * Multifunction steering wheel * LED headlights * Dual PTO / power take-off Lrjdpfx Ajy Hn E Ija Rjr * Automatic transmission * Differential lock * Central locking with remote control * ADR/GGVS (hazardous goods equipment) Subject to prior sale and errors excepted! Sale exclusively according to our terms and conditions. Important note: Despite careful verification of all details in our offer, errors may occasionally occur. In some cases, these are caused by data transfer mistakes within the systems of different platform providers. We therefore point out that all information is provided without guarantee and does not constitute a legal claim. Legal notice: This sales advertisement does not constitute an offer as defined by §145 BGB. Rather, it is information intended to facilitate contractual negotiations. The information provided here is non-binding and does not constitute warranted characteristics.

Condition: good (used), total height: 7,500 mm, outer diameter: 2,750 mm, 32000l Insulated stainless steel tank with a side-mount propeller agitator Diameter: 2.75 m Lrodpfx Aozvwlgea Rsr Height: 7.5 m Slightly conical bottom It has legs

Year of construction: 2019, condition: ready for operation (used), A mixing vessel KG Bremen and two stirrers PRG and IKA are available. 1) Mixing vessel KG Bremen, year of manufacture: 2019, max. operating pressure: atmospheric, max. operating temperature: 80°C, volume: 1150L, max. double-jacket operating overpressure: 5bar, max. double-jacket operating temperature: 80°C, material: 1.4301. 2) Precision stirrer PRG R112M-6, year of manufacture: 2004, agitator length: 930mm, impeller diameter: 160mm. 3) Precision stirrer IKA RF 04-T-1085, year of manufacture: 1999, total length: 1100mm, impeller diameter 1/2: 160mm/200mm. An on-site inspection is possible. Ljdpoxhntrofx Aa Rerr

Year of construction: 2002, condition: ready for operation (used), There are three identical agitator tanks available, capacity: 10,000l, operating overpressure inner tank/ jacket: -1 to 6/ 6bar, diameter: 2500mm, height: 3180mm, weight: 10.5t, with motor, gearbox, lantern, barrier pressure system and documentation, the tanks were used for 15 years. Lsdopwh Slepfx Aa Rsrr

Condition: good (used), Used stainless steel mixing vessel with a double jacket Article number: 10492 Last application: Food Volume: approx. 1400 liters Type: Standing on 4 legs Material (in contact with the medium): 1.4301 stainless steel Design: With double jacket Manhole: 1250x420mm hinged cover on both sides Bottom: Curved Top: Hinged cover Operating pressure according to nameplate: ATM Dimensions of the vessel: Outer diameter: 1460mm Cylindrical height: 870mm Overall height: 2040mm Ledpfxsfiguuo Aa Rorr Overall width: 1460mm Height of legs: 560mm Materials: Inside: 1.4301 / AISI304 Exterior parts: 1.4301 / AISI304 Equipment: Double jacket Nameplate: yes Outlet: 70mm Various connections Grid grates Mixer

Year of construction: 2025, condition: new, Brand new stainless steel agitator tank with beam agitator and load cells CILC2000RWS Volume: 2107L Dimensions approx.: Ø 1430mm x cyl. Height 1250mm Total height: approx. 1650mm (plus agitator motor) Material: 1.4301 stainless steel V2A Surface: inside BA (IIId), outside satin finish Lrjdsvtyf Iepfx Aa Rjr Welding seams in the container ground -Standing design on three feet -Top: hinged lid, central crossbar with 2 hinged lid halves with locking function (can be locked in 90° open position) -Metal grates below the hinged lid as protection against soap, screwed, removable -Bottom: conical bottom with central outlet DN50 DIN11851 nozzle -Agitator flange on the top -1x reserve nozzle DN50 DIN11851 on the top with blind cap -Type plate -180° spray head - Weighing cells - Speed control Agitator: Bar agitator Make: Schwarzer Rührtechnik GmbH Type: SRTGMK/1.5-149 Power: 1.5KW Speed: 149RPM Operating voltage: 3PH 400V -Gearbox made by Getriebebau NORD -Solid agitator shaft with sleeve coupling attached to the gear motor, removable -Agitator shaft balanced for concentricity in the speed range -2 2-blade bar agitators Ø 500mm, height adjustable on the agitator shaft, attached via side power screws Grilled and passivated -Stainless steel flange with shaft seal and O-ring seal -MFR converter

Condition: ready for operation (used), Used heatable/coolable pressure vessel with Atex agitator and insulation Last intended use: Pharmaceuticals, cosmetics Article number: 10815 Volume: 5600 liters Type: standing on 4 feet Material (in contact with media): 1.4571 / AISI316 Design: with double jacket and insulation Operating pressure according to nameplate: +1/+3 bar Max. operating temperature: 0/ +150 °C Container dimensions: Manhole: 500mm Outer diameter: 2000mm Lsdpetdgkxofx Aa Rerr Total height: 2870mm Total width: 2250 x 2060mm Cylindrical height: 2000mm Materials: Inside: 1.4571 / AISI316 Outside parts: 1.4301 / AISI304 Facilities: Nameplate: Yes ATEX agitator Power: 22KW Speed: 1465/min Agitator: Propeller 2x spray head Connector

Condition: used, Equipment: type plate available, Electrically heated agitator tank with double jacket and insulation Article number: 10707 Volume: 300 L Type: Vertical, standing on 3 legs Leg height: 220 mm Material (product-contact): V2A stainless steel Design: Electrically heated Operating pressure according to nameplate: ATM (atmospheric) Tank dimensions: Internal diameter: 700 mm External diameter: 950 mm Cylindrical height: 730 mm Total height: 2030 mm Total width: 1120 mm Total length: 1340 mm Equipment: Nameplate: Yes Discharge to floor distance: 415 mm Outlet valve: Ball valve Outlet diameter: DN40 Opening: 235x750 mm Beam agitator Double jacket: 100 L Insulated Lrodpfx Aasw Ic Nie Rjr Control cabinet Foldable lid 1/2

Condition: good (used), Used stainless steel reactor with double jacket, insulation, and agitator Article number: 10257 Last application: Chemical industry Volume: approx. 8000 L Operating pressure: +16/-1 bar Type: Standing on legs Material (in contact with media): 1.4301 / AISI304 Design: Double jacket and insulated Bottom: Klöpper bottom Top: Klöpper bottom Dimensions of the vessel: Vessel inner diameter: 2140 mm Cylindrical height: 1600 mm Overall height: approx. 3820 mm Height of legs: 710 mm Outer diameter: 2200 mm Distance from outlet to bottom: 500 mm Materials: Inside: 1.4301 / AISI 304 Outside: 1.4301 / AISI 304 / Painted steel Equipment: Insulation Double jacket around the cylinder Various connections on the top Dome lid on the top Lrodpfx Aajd Dwmwj Rjr Agitator with double-acting mechanical seal