Used Engel Engel Duo 3550/550 Tech for sale (8,279)

Condition: good (used), Year of construction: 2002, _Engel ES 750/200 HL_ Clamping force: 200 t Year of manufacture: 2002 Control system: CC 100 Screw diameter: 50 mm Screw type: GF Min. mold height: 250 mm Max. opening stroke: 700 mm Max. platen distance: 950 mm Ejector stroke: 150 mm Tie-bar spacing (H × V): 820 × 750 mm Platen size: 500 × 570 mm Itjdpjzr U Hmofx Aayok Quick clamp: Yes Needle shut-off: Yes Extras: Water battery extended for adapter plate

Condition: ready for operation (used), Year of construction: 1997, operating hours: 113,881 h, functionality: unexamined, machine/vehicle number: 32833, total length: 6,500 mm, total width: 2,000 mm, total height: 2,200 mm, overall weight: 11,500 kg, For sale is a used machine from a site closure. Sale is made with the exclusion of any warranty for defects. Iedpfx Aozl S Rpeaystk The machine has not been inspected but was in working order until the end.

Condition: excellent (used), Year of construction: 2013, KRAUSS-MAFFEI KM 550-4300 GX injection molding machine Year of manufacture: 2013 Control system: MC6 Clamping system: hydraulic-mechanical, two-platen Injection unit: 4300 Design and control Hydraulic-mechanical two-platen clamping system with 4 pressure pads on the fixed platen and 4 adjustment units on the moving platen. PV – injection unit adjustment. MC6 control system with a color TFT monitor, integrated control panel, and USB data storage. Itedpfx Aajzvm Dloyek Plasticizing unit Complete plasticizing unit for thermoplastics with abrasion protection. Screw diameter: 90 mm Backflow valve: yes Nozzle: open Clamping unit Clamping force: 5500 kN / 550 t Mold opening force – pressure pads: 385 kN Platen dimensions (H × V): 1430 × 1350 mm Distance between columns (H × V): 1040 × 910 mm Maximum mold opening stroke: 1350 mm Minimum/maximum mold height: 400–950 mm Maximum distance between platens: 1750 mm Ejector stroke: 250 mm Ejector force front / rear: 95 / 49 kN Injection unit 4300 Screw diameter: 90 mm Ls/D ratio: 20:1 Maximum injection pressure: 1839 bar Injection volume: 2290 cm³ Injection weight for PS: 2084 g Injection rate: 636 cm³/s Screw speed: 195 rpm Nozzle clamping force: 129 kN Electrical and hydraulic equipment Rated motor power: 90 kW Installed heater power: 44 kW Number of cylinder heating zones: 7 Dry cycle time / stroke according to EUROMAP 6: 2.8 s / 728 mm Dry cycle time / stroke according to KraussMaffei standards: 2.5 s / 520 mm Oil tank capacity: 1180 l Dimensions and weight Machine dimensions (L × W × H): 8.08 × 2.80 × 2.39 m Net weight with control cabinet: 25.0 t

Condition: good (used), Year of construction: 2014, DIP TECH GlassJet NOVO digital printer: Print resolution: 720 dpi Ink color: black, similar to etching, white and other spot colors Maximum glass size: 2200x1200 mm (width x height) Minimum glass size: 400 x 400 mm Glass thickness: 2-19mm Print speed: up to 30 m2/h (in the context of 8 print heads for one color) Number of required operators: one Itsdpoiukuuofx Aayek Overall dimensions: 2,500 x 4,700 x 2,000 mm (width x length x height) Image format: All common image file formats including: PDF, PS, EPS, TIff, BMP, JPEG Ambient temperature 18-25 degrees Celsius Power supply: Single-phase 400VAC x 16A 50/60 Hz

Condition: like new (used), Year of construction: 2025, rotary table diameter: 1,000 mm, Equipment: rotational speed infinitely variable, - Horizontal load capacity: 1200 kg - Vertical load capacity: 600 kg Iedszcyxqspfx Aaystk - Table dimensions: 1000 mm - Electrically tiltable - Wireless remote control - Digital display - Documentation - 400V

Condition: repair required (used), Year of construction: 1999, operating hours: 33,400 h, functionality: limited functionality, machine/vehicle number: 70185/300/99, screw diameter: 45 mm, injection pressure: 2,038 bar, total length: 7,200 mm, total width: 2,000 mm, total height: 2,500 mm, overall weight: 22,000 kg, For sale is an ENGEL ES650/330/300 TL injection molding machine in a C-frame design. The machine is ideal for repair, modernization, or as a source of spare parts. Technical data: Manufacturer: ENGEL Type: ES650/330/300 TL Year of manufacture: 1999 Machine number: 70185-300-99 Clamping force: 3,000 kN Design: C-frame 1 horizontal injection unit Ijdpjzrngyofx Aaystk Screw diameter: 45 mm Injection volume: 292 cc Injection pressure: 2,038 bar Max. injection temperature: 450 °C Min. tool mounting height: 400 mm Max. distance between mounting platens: 1,300 mm Ejector stroke: 200 mm 3 hydraulic core pulls Dimensions and weight: Length: 7.20 m Width: 2.00 m Height: 2.50 m Total weight: approx. 22,000 kg Connection values: Pump drive power: 37 kW + 11 kW Heating power: 15.3 kW + 9.2 kW Fuse rating: 250 A Condition The machine is generally functional but requires repair or maintenance. An inspection of the machine is strongly recommended. Further information on the condition can be provided upon request. Sale Location: [Insert location] Inspection possible by appointment Sale from the location Please contact us for further information, images, or to arrange an inspection.

Condition: used, Year of construction: 2015, Lot consists of: (1) Injection molding machine, Handling: Sepro Robotique | SR SUCCESS11 S3 Trans | 2014 Temperature control: HB Therm | Miscellaneous: 1x Protective Enclosure 1x Handling system 1x Conveyor belt Technical Details: Max. stroke (mm): 175.0 Measuring system: Incremental encoder Clamping system: Toggle (KH) Clamp force (kN): 1000 Injection servo: No Screw diameter (mm): 40.0 Screw speed (rpm): 420 Heating zones: 4 Itsdpsy N R N Uofx Aayjk Heating power zone 1 (kW): 4.23 Heating power zone 2 (kW): 3.00 Heating power zone 3 (kW): 3.00 Heating power zone 4 (kW): 3.00 Temperature control: J-type thermocouple Pressure sensor type: Diaphragm

Condition: like new (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: M134377I2WA, turning diameter: 300 mm, spindle speed (max.): 5,000 rpm, rotational speed (max.): 2,500 rpm, workpiece weight (max.): 30 kg, total height: 3,300 mm, total length: 2,200 mm, total width: 3,400 mm, overall weight: 9,600 kg, Equipment: documentation/manual, rotational speed infinitely variable, Fully automated Hwacheon Hi-TECH CNC lathe with WEKAL portal system including robot Ijdpfx Aajzhltceyjtk Base: Hwacheon Hi-TECH 450BL YSMC (Siemens) Year of manufacture 2024 | Like new | Manufacturer's warranty until 03/26/2027 | Immediately available Highlights ✓ Year of manufacture 2024 ✓ Automatic door drive ✓ Like new condition ✓ Robot interface ✓ Fully functional ✓ Travel monitoring ✓ Manufacturer's warranty until 03/26/2027 ✓ High-pressure coolant system ✓ Siemens SINUMERIK with ShopTurn ✓ Oil/emulsion mist filter ✓ DXF reader integrated ✓ Fully automatic WEKAL portal system ✓ Y-axis ±60 mm ✓ WEKAL WRB roller conveyor ✓ Counter spindle 4,000 rpm ✓ Robot gripper module ✓ Driven tools up to 5,000 rpm ✓ Complete documentation ✓ Torque upgrade ✓ Ongoing maintenance with records Complete automated production cell The system is designed for the automated machining of round stock. Workpiece range: • Diameter 50–300 mm • Workpiece weight up to 30 kg The WEKAL automation system handles the loading and unloading of workpieces and enables economical operation with minimal manual intervention. WEKAL WPA portal system • 2-axis portal system • X-beam 7,000 mm • X-travel approx. 5,500 mm • Z-travel approx. 1,800 mm • Conveyor length WRB roller conveyor 10,000 mm • 20 workpiece carriers • Robot gripper module with quick-change system Machine equipment • Siemens ShopTurn • ProfiNet • Touchscreen • DXF reader • Network drive management • Geared spindle 22/18.5 kW • 2,500 rpm • Y-axis ±60 mm • Counter spindle • Driven tools 5,000 rpm • Torque upgrade • High-pressure cooling • Oil mist extraction • Chuck flushing • Chuck blow-out • Travel monitoring • Automatic door drive • Robot interface Documentation and condition The system is in like-new and fully functional condition. • Complete documentation available • Ongoing maintenance including records • Manufacturer's warranty until 03/26/2027 • Available in the short term The system can be inspected while powered on. Training and instruction are possible. Programming and setup of your components are possible. Sale ex works. Buyer organizes disassembly, loading, and transport.

Condition: excellent (used), Year of construction: 2013, Engel Victory 330H/80V/160 combi Ecodrive / Production line with the Sepro SR S5-25 S3 Trans robot / Operating hours: approx. 18,000 h in automatic mode Year of construction: 2013 Injection unit: Screw diameter: 30 mm Injection weight: approx. 100 g Injection pressure: 2385 bar Dosing volume: 113 ccm Clamping unit: Clamping force: 160 t Itodpfezc Nywjx Aayek Distance between tie bars: 0x0 mm Size of the clamping plates: 750x750 mm Ejector: hydraulic Clamping unit: hydraulic Control: CC 200 - touch screen Additional equipment: 2K injection molding machine with rotary table and robot Tie-bar-less machine, hybrid: energy-saving, high-speed and very quiet Very good technical condition Operating hours: approx. 18,000 h in automatic mode Total number of operating hours: 24,312 h Euromap 67 Robot interface Air valve x 5 Hydraulic core pull x 5 Control unit with hot runners x 16 Reinforced injection units - bimetal Main motors - 2 x servo motor controlled with inverter Proportional valves on injection units - precise spraying Screw diameter in the vertical injection unit: ⌀22 mm - approx. 28 g/hp It is possible to purchase a turntable Robot Sepro SR S5-25 S3 Trans Year of construction: 2013 3-axis robot: 3 axes are driven by servomotors (electric): X, Y, Z (telescopic) Travel distances in axes approx.: X-2000, Y-1000, Z-1500 Automatic axis lubrication Touch control panel The safety package for robots Robot with adapter and protective housing Purchase of the robot for an additional charge Dimensions Weight: 8700 kg Length/width/height: 5.35x1.76x3.42 m All offered machines are started by our service technicians before sale. It is possible to obtain a video of technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: good (used), Year of construction: 2013, Ref. no.: 18494 Manufacturer: ENGEL Type: Victory 50-200 Spex Year of construction: 2013 Clamping unit Clamping force: 50 ton Opening stroke: 400 mm Mould height min.: 200 mm Opening width: 600 mm Platen size (h x v): 500 X 450 mm Injection unit Screw diameter: 25 mm Injection volume: 69 cm³ Shot weight: 62 g Injection pressure: 2400 bar Measurements and weight Dimensions: 3,4 x 1,3 x 1,8 m Machine weight: 2900 kg Additional information & extras Core pull: 1 pcs Further information: ENGEL ENGEL Victory 50 SPEX (2013) – Tie-Barless Injection Moulding Machine For sale is a high-quality ENGEL Victory 50 SPEX injection moulding machine from 2013. Featuring tie-barless technology and a special SPEX configuration, this machine is ideal for precise and flexible production. Key Advantages: Tie-barless design → maximum mould accessibility SPEX special configuration → optimized for specific applications High precision & repeatability Energy-efficient operation Compact design → space-saving Automation-ready (robot interface possible) Iedpfx Ajxzq Sksayjtk Applications: Automotive industry Electronics Medical parts Technical plastic components 👉 Machine in good working condition. Inspection possible upon request.

Condition: good (used), Year of construction: 2019, Schulte Lagertechnik Pallet Racking – Starter Bay Manufacturer: Schulte Lagertechnik Rack type: Starter bay Upright type: S610-M18 Total length: 2700 mm Rack height: 4500 mm Rack depth: 1100 mm Clear bay width: 2700 mm Beam type: LNS-Duo 110 x 50 x 2700 mm Number of storage levels: 4 (incl. floor level) Number of bays: 3 Max. beam load: 2580 kg Max. bay load: 8200 kg Pallet spaces: 12 Scope of delivery: 02 x Schulte pallet rack uprights 4500 x 1100 mm (blue) 06 x Schulte pallet rack beams 2700 x 110 x 50 mm, 2580 kg (orange), incl. locking pins Your partner for safe warehouse logistics: assembly, disassembly & rack inspection An efficient warehouse is the backbone of your success. We ensure that your racking systems are professionally installed and meet all safety standards. Ijdezrlkvopfx Aayetk As experts in warehouse technology, we offer a comprehensive one-stop service: Assembly & Disassembly Whether for new installations, reconfiguration, or warehouse decommissioning, we handle the professional assembly and dismantling of your systems: - Pallet racks (heavy-duty & standard) - Shelving units for small parts and archives - Mezzanine floors for optimal space utilization Rack Testing & Inspection (DIN EN 15635) Safety is a legal requirement. We conduct the annual expert inspection (in accordance with DGUV Rule 108-007): - Inspection for deformation and damage. - Checks of locking pins and load capacity signs. - Preparation of a legally compliant inspection report, including an inspection sticker. “Everything from a single source: We would be happy to offer you suitable bank financing for your project.” komplett-konzept.leasingo.de You can find more items—both new and used—in our shop! International shipping costs available upon request!

Condition: good (used), Year of construction: 2001, Ref. no.: 18092 Manufacturer: ENGEL Type: ES 1350H 200W / 300HL-2F Year of construction: 2001 Clamping unit Clamping force: 300 ton Opening stroke: 855 mm Platen size (h x v): 1050 x 650 mm Injection unit Screw diameter: 60 +35 mm Injection volume: 735 +135 cm³ Shot weight: 662 + 122 g Injection pressure: 1834 +1620 bar Measurements and weight Itsdpswm Iy Eofx Aayok Dimensions: 7,75 x 2,35 x 2,6 m Machine weight: 24780 kg Further information: ENGEL ES 1350H200W/300HL-2F — 2K Injection Moulding Machine This machine from the prestigious Austrian manufacturer ENGEL, built in 2001, features a clamping force of 300 tonnes and a true 2K L-configuration in horizontal layout. Motor and Hydraulic System The machine is equipped with a powerful electric motor coupled to a high-pressure hydraulic pump group. The electric motor continuously drives the hydraulic pump, providing pressurised oil flow throughout the entire system. This pressurised oil feeds the clamping cylinder, the injection pistons of both units, and the ejector system. The thick red hydraulic hoses visible behind Unit B carry this high-pressure oil flow — both units are supplied via independent hydraulic circuits, allowing Unit A and Unit B to operate simultaneously without influencing each other. Operating Principle The two independent injection units are positioned at 90° to each other — in an L-shape. The mould is locked with 300 tonnes of clamping force. Unit A injects the primary material into the mould at 1834 bar. Immediately afterwards, Unit B injects the second material or colour from a 90° angle into the same mould at 1620 bar. The two materials bond at a molecular level inside the mould, cooling is completed and the ejectors push out the finished 2K part as a single piece. No gluing, screwing or assembly is required — two materials emerge as one single part in a single cycle. Applications Automotive interior and exterior trim parts, large technical plastic components, parts combining a rigid body with a soft grip surface, two-colour large-surface parts.

Condition: excellent (used), Year of construction: 2016, Clamping force (kN): 1600 Opening stroke (mm): 460 Mould height (min–max) (mm): 250 – 600 Platen size (mm): 760 × 760 Tie bar distance (mm): 520 × 520 Ejector stroke / force (mm / kN): 150 / 40 Dry cycle time (sec): 1.4 – 320 Ijdoyyz Ddepfx Aayotk Screw diameter (mm): 30 Screw stroke (mm): 160 Shot volume (cm³): 113 Screw speed (rpm): 420 L/D ratio (3 zones): 23.6 / 20.0 Plasticizing capacity (g/sec): 15 / 22 L/D ratio (barrel): -29 Plasticizing capacity (barrel) (g/sec): -29 Injection flow (cm³/sec): 157 / 214 Injection pressure (bar): 2400 / 2000 Nozzle stroke / force (mm / kN): 225 / 28 Drive / Power Pump motor power (kW): 16.91 Working hours 13.227 h Type: Multicomponent Drive: Electric Possible to buy with Viper robot

Year of construction: 2014, operating hours: 12,583 h, condition: used, functionality: fully functional, machine/vehicle number: VKARC1310E0000007, The Stonefex 3000 stone separator reliably and efficiently removes stones and inert objects from biomass. The input product is typically a biomass fraction, such as that obtained from a screen, for example, the woody part of green waste, an intermediate fraction after compost screening, or wood chips. Itsdpszt I Rujfx Aayek

Condition: new, Extraction capacity of filter unit at spigot*: 3550 m³/h (free-eye) Total power consumption*: 0.88 kW Operating voltage: 400 V, 50/60 Hz,3Ph+PE Noise level*: 73 db(A) Dimensions L/W/H in mm: L 1283 / W 1020 /H 595 Colour: RAL 7035 Itodpfxjh Rdyps Aayjk Weight: 170 kg Manufacturer: ISI Industrieprodukte GmbH *Depending on filter equipment Special voltage or special colour on request Application: Extraction of oil mist and smoke, for small to very large machine workrooms (oil mist separator). Your advantages of the ELBARON series: - 18 unit variants available - Direct from the manufacturer - ISI-TRONIC as standard (digitalised filter control) - Electronically controlled EC fan as standard - Speed and air flow rate adjustable - Simplex (single-stage) or duplex (two-stage) available - Wide range of air flow rates available - Adaptable to pollutant load and air performance requirements - Large range of mounting and connection accessories - Quality Made in Germany We have developed the ELBARON® filter series for use in machining operations with pure oil or for separating oil mist and smoke. For many years now, the digital electrostatic air filters of the ELBARON® series have been among the most efficient filter units on the market and are in use worldwide. Our filter units are already digitalised as standard and can be controlled, for example, using a laptop. The ELBARON® unit series comprises 18 unit variants and can be optimally designed for your application in terms of size and performance. ELBARON® units impress with their long service life and absolute functional reliability. Our electrostatic filter cells are dimensioned in such a way that the best possible filter efficiencies, service lives and trouble-free operation are achieved under economic aspects.

Year of construction: 2005, condition: used, functionality: unexamined, machine/vehicle number: X-1802, Used Andor Ixon DV885JCS-VP microscope camera in a case. Manufacturer: Andor Technology Itsdpfx Aszgtnfoayek Model: (Ixon) DV885JCS-VP Includes software, power supply, connection cables, and system PCBs.

Year of construction: 2021, condition: excellent (used), 2021 Versa Tech Enterprise Soundproof Welding Room/Acoustic Welding Enclosure Consisting of: 1. 1st Enclosure 3 Twin Door Soundproof Welding/Assembly Booths Dimensions (2) W3,000 x D4,000 x H2,700mm & W4,000 x D4,000 x H2,700mm With Donaldson Torit Extraction Unit Dimension W1,399 x D1,284mm. 2. 2nd Enclosure 2 Assembly Soundproof Booths Dimensions W4,800 x D4,000 x H2,700mm & W2,800 x D4,000 x H2,700mm With Donaldson Torit Extraction Unit Dimension W1,399 x D1,284mm. 3. 3rd Enclosure 2 Soundproof Welding/Assembly Booths Dimensions W2,500 x D2,500 x H2,700mm & W4,200 x D2,500 x H2,700mm With Donaldson Torit Extraction Unit Dimension W1,399 x D1,284mm. Iedpfx Aaszk Dw Eoyetk 4. 4th Enclosure 3 Twin Door Soundproof Welding Booths Dimensions (2) W2,000 x D2,500 x H2,700mm & W3,000 x D2,500 x H2,700mm With Donaldson Torit Extraction Unit Dimension W1,319 x D1,284mm. 5. 5th Enclosure 6 Twin Door Soundproof Welding Booths Dimensions (5) W2,000 x D2,500 x H2,700mm & W3,000 x D2,500 x H2,700mm With Donaldson Torit Extraction Unit Dimension W1,119 x D1,284mm. Please see document attached for more details.

Condition: excellent (used), Year of construction: 2009, Engel e-max 440/180 / All-electric injection moulding machine Year of manufacture: 2009 Injection unit: Screw diameter: 40 mm Shot weight: approx. 199 g Injection pressure: 1950 bar Shot volume: 220 cm³ Clamping unit: Clamping force: 180 t Itjdpfozc Nz Iex Aayok Tie bar distance: 520 x 520 mm Platen size: 760 x 775 mm Ejector: electric Clamping system: toggle lever Control system: CC 200 - touchscreen Additional equipment: Machine in very good technical condition, operated in a clean production environment All-electric machine: high-speed, energy-saving, and very quiet Euromap 67 interface Robot interface 3 x air valves Hardened injection unit - bimetallic Parallel movements Central lubrication Automatic mould height adjustment Kistler sensor - mould pressure control Original mould crane Dimensions: Weight: 7,200 kg Length/Width/Height: 5.87 x 1.42 x 2.00 m All machines offered are started and tested by our service technicians prior to sale. It is possible to receive a video of the technical tests carried out on the selected machine, or to participate in live technical demonstrations at our company in Łódź. Price: On request

Condition: good (used), Year of construction: 2013, Clamping Force: 60 tons (600 kN) Injection Unit Orientation: Vertical Ijdswp E Hzjpfx Aaystk Rotary Table: Included Screw Diameter: 25 mm Shot Size: Around 4.4 oz (125 g) Injection Pressure: Up to 210 bar Injection Speed: Approximately 139 mm/s Mould Opening Stroke: 305 mm Ejector Stroke: 106 mm

Condition: excellent (used), Year of construction: 2016, Machine designation: VC 330H/200V/80 Combi Clamping unit: Clamping force: 80 tons Opening stroke: 458 mm Ejector stroke: 100 mm Ejector force: 39.8 kN Injection unit 1: Screw diameter: 25 / 30 / 35 / 40 mm Max. swept volume: 79 / / 154 / 201 cm³ Screw speed max: 400 / 425 / 400 / 320 rpm Screw speed max current: 425 rpm Injection rate: 67 / 97 / 132 / 172 cm³/s Injection rate increased: 50 / 71 / 97 / 127 cm³/s Specific injection pressure: 2401 / 2181 / 1595 / 1225 bar Specific injection pressure increased: bar Nozzle stroke: 500 mm Itedpfx Aoyyzzvjayjk Nozzle contact pressure: 48.9 kN Injection unit 2: Screw diameter: 15 / 18 / 22 / 25 mm Max. swept volume: 18 / 25 / 99 / 49 cm³ Screw speed max: 480 / 480 / 480 / 480 rpm Screw speed max current: 480 rpm Injection rate: 37 / 54 / 149 / 104 cm³/s Injection rate increased: 28 / 40 / 98 / 77 cm³/s Specific injection pressure: 2200 / 2200 / 1451 / 1230 bar Specific injection pressure increased: bar Nozzle stroke: 380 mm Nozzle contact pressure: 40.7 kN Type: Multicomponent Drive: Hydraulic

Condition: ready for operation (used), Year of construction: 2015, operating hours: 5,159 h, spindle motor power: 7,500 W, spindle speed (max.): 6,000 rpm, overall weight: 4,200 kg, total width: 1,900 mm, total height: 1,900 mm, bar diameter (max.): 100 mm, travel distance X-axis: 150 mm, travel distance Y-axis: 385 mm, controller manufacturer: MITSUBISHI, product length (max.): 3,500 mm, number of axes: 7, This 7-axis Quick-Tech I-42U was manufactured in 2015. It features a maximum bar diameter of 42 mm and a maximum machining length of 250 mm. The machine is equipped with a powerful spindle speed of 6000 rpm and includes an automatic bar feeder. If you are looking to get high-quality turning capabilities, consider the Quick-Tech I-42U swiss type turning machine we have for sale. Contact us for further details. • Control • Mitsubishi M720 CNC • 15" color LCD display • Door with LED indicators • Operational signaling and automatic alarm switch • Built-in communication/interface with bar feeder • CE mark • Guide/manual • Main spindle • Bearing diameter: 100.0 mm • Max bar dia.: 42 mm • Max machining length: 250.0 mm • Collet: DIN-173E42B • Spindle nose: A2-5 • Spindle bore: 44.0 mm • C axis: 0.001° • Counter spindle • Max bar dia.: 42 mm • Max machining length: 100 mm • Collet: DIN-173E-42B • Spindle nose: A2-5 • Speed: 4000 rpm • Power: 3.7 kW • C1 axis: 0.001° • Travels and axes • X: 150.0 mm | Y: 385.0 mm | Z: 250.0 mm | B: 360° Isdpszcwxnofx Aayetk • X1: 400.0 mm | Y1: 400.0 mm | Z1: 300.0 mm • Servo motors (X, Y, Z, X1, Y1, Z1): Mitsubishi AC Servo, 1.5 kW each • Indexing from tool position: 0.3 s • Tool change time (cut/cut): 0.6 s • Tool head (main) • Combined type • Tools: 6 external, 5 internal • External tool size: 20.0 × 20.0 mm • Max internal tool: ER20 / 20.0 mm • Driven tools (main) • B axis with 12 driven tools • Power: Mitsubishi AC Servo, 15 kW • Speed: 4000 rpm • Max tool size: ER-20 • Max drilling dia.: 12 mm • Max thread: M10 × 1.5 • Tool head (counter) • Combined type • Tools: 5 external, 9 internal • External tool size: 20.0 × 20.0 mm • Max internal tool: ER20 / 20.0 mm • Driven tools (counter) • Number: 6 (3 axial, 3 radial) • Power: Mitsubishi AC Servo, 1.5 kW • Speed: 4000 rpm • Max tool size: ER-20 • Max drilling dia.: 12 mm • Max thread: M10 × 1.5 • Hydraulic system • Hydraulic motor: 0.75 kW • Max system pressure: 50 kg/cm3 • Lubrication system • Lubrication motor: 25 W • Tank capacity: 2 l • Cooling system • Coolant tank: 200 l • Coolant motor: 1/4 HP • Coolant pressure: 2.5 MPa • Length: 2900 mm (3500 mm including chip conveyor, which is part of the machine) • Standard equipment included • Basic equipment with tools • Tool holder and collet set • Automatic lubrication • Chip remover/chip conveyor (integrated, per dimensions note) • Workpiece removal (shovel) – if integrated • 15" color LCD display • Operational signaling and automatic alarm switch • Guide/manual • Door with LED indicators Additional equipment • Automatic bar feeder, 1200 mm length • Workpiece removal conveyor • Workpiece removal shovel (if provided as an external unit) • Transformer 380–440 V, 60/50 Hz Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: used, Year of construction: 2019, functionality: fully functional, Flexographic printing machine Rotary Print 260 from 2019, Tech-Wash 8 UV colours Manual colour registration Web guiding control One die-cutting station Web width: 250 mm Max. roll diameter on unwinder: 1000 mm Max. roll diameter on rewinder: 1000 mm Iedjxrdb Hjpfx Aayetk Max. roll diameter (matrix) on rewinder: 500 mm Machine working speed up to 120 m/min depending on material type Units for web-turning, peel-off, lamination included Comes with 10 anilox rolls, 7 sets of printing cylinders, and 7 magnetic cylinders. Machine is 100% operational and in continuous use.

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, overall weight: 4,400 kg, Equipped with Iemca Boss 545 barfeed and Mitsubishi M700 Control - the lathe has always operated with oil, in regular working order (bearings and ball screws of the X1/Z1 axes and 2 drives have just been replaced). Itedpfxjynt U Ae Aaysk

Condition: excellent (used), Year of construction: 2006, operating hours: 33,107 h, functionality: fully functional, clamping force: 1,300 kN, screw diameter: 25 mm, displacement volume: 79 cm³, injection pressure: 2,398 bar, ejector force: 6,100 N, ejector stroke: 100 mm, opening stroke: 606 mm, plate length: 750 mm, plate width: 850 mm, overall weight: 10,600 kg, Equipment: documentation/manual, ENGEL V 330H/80V/130 Combi Cleanroom – 2-component injection molding machine, manufactured in 2006. The machine comes from pharmaceutical production and is designed for cleanroom applications. Iodjt A Ui Aspfx Aayjtk Technical data: • 33,107 operating hours • Screw diameter 25/22 mm • Machine weight 10,600 kg Available additional equipment: • GEKU SR 500 ST robot • Safety cage • Rotary table • Conveyor belt Location: Schwaigern, Germany. Further technical documentation and an inspection can be arranged.

Condition: new, Year of construction: 2023, operating hours: 1 h, functionality: fully functional, Equipment: rotational speed infinitely variable, BE 2500 Liter Steel Enamel Reactor Agitated Tank, condition unused CRYOLOCK® 2-stage agitator, enamel color blue, conductive enamel layer, support ring construction. Nominal capacity: 2500 liters, total volume: 3500 liters. Heating/cooling via double jacket. Double jacket capacity: 430 liters Operating pressure in the vessel: -1/+4 bar, double jacket: -1/+8 bar, operating temperature: -30/+160 °C, bottom outlet valve. Total weight approx. 3800 kg Manufactured according to AD-2000 Ed. 2012 Drive motor and gearbox ATEX certified, gearbox infinitely adjustable. Technical details are available on request. Please contact us for a written quotation. Dismantling, packaging, and loading onto a truck will be organized and supervised by Cycron GmbH. We therefore guarantee highly professional execution of all work. For further questions or to contact us, please feel free to reach out at any time, we look forward to hearing from you. Iodsyfg Azopfx Aayetk Cycron GmbH, Switzerland