Used Rsa Brush Sander 1500/3000 Rpm, for sale (23,413)

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Hedjuxfu Njpfx Anyou Pr...

Condition: used, Compact dust collector, dust extraction system HURRICAN Type Tonga BG32 / ST / 27-3000 Filter system, extraction system, central extraction system, cartridge impulse filter, dust extraction Cartridge filter system, rectangular filter system, central fume extraction system Ideal for plastics, metals, wood, etc. Manufacturer: DAMBAUER GmbH Air and Environmental Technology Brand: HURRICAN Model: Tonga Machine No. 50313000 62187 Year of construction 2014 Nominal volume flow 3000 m³/h Nominal volume flow 50 m³/sec Filter area 27 m² (9 pieces, each with 3 m²) Differential pressure 3699 Pa Extraction connection at the filter inlet Ø 250 mm Extraction diameter max. 355 mm (manufacturer's specification) Exhaust connection at the filter outlet 600 x 600 mm Compressed air connection 5 bar Compressed air requirement 60 standard liters per cleaning impulse Motor power 5.5 kW Hodpfx Aez Db Nijnyju Mains connection 400 Volt, 50 Hz - Filter control via SIEMENS PLC S7-1200, with touch panel - Pneumatic filter cleaning, automatic via control - Control cabinet mounted on the extraction system - 9 filter cartridges, Type 51065081200, Ø 160 mm, length 1180 mm - Maintenance flap for filter replacement - Radial fan installed on the top inside, Type VUVI 500 DF - 2 mobile dust collection containers, each approx. 106 liters (ECO bins) - Firewater connection with sprinkler nozzle in the filter chamber - Electrical wiring diagram available - Silencer on the air outlet side 600 x 600 x 1000 mm Space requirement L x W 1850 x 1500 mm Width with silencer on the air outlet side 2500 mm Overall height 4050 mm Footprint 1080 x 1080 mm Weight 820 kg (manufacturer's specification) Weight 1070 kg (weighed) Very good condition Transport dimensions for horizontal transport: Length 420 cm x Width 190 cm x Height 200 cm Transport weight: 1150 kg

Condition: good (used), machine/vehicle number: 17068, Year of construction: 2022, operating hours: 2,069 h, load capacity: 3,000 kg, lifting height: 4,900 mm, free lift: 1,350 mm, load center: 600 mm, fuel type: electric, mast type: triplex, construction height: 2,250 mm, battery voltage: 28 V, fork length: 1,150 mm, front tire size: 16x7x10,5, rear tire size: 22x10x16, overall weight: 8,610 kg, Equipment: 3rd hydraulic function, 4th hydraulic function, 5140896 Serial Number: 64882 Battery Details: 28V 6EPzS 930 und 20V 6EPzS 930 (aus 2022) Hjdpfxezfd A De Anyou

Condition: good (used), Deburring machine with brushes RSA Duo Deburring Machine Brush diameter 255 mm 2 speeds Hodpezduh Ijfx Anyju Motor power 2.4 / 3.7 kW 1500/3000 rpm

Condition: new, Catalog number: O222 Hsdpfx Aeztap Asnyju ADVANTAGES – grinding length 2600mm – electric table height adjustment – new machine – warranty – CE certificate TECHNICAL DATA table size 2600x800mm table lift 570mm pulley 250mm electric table height adjustment 0.37kW belt speed 18m/sec sanding belt size 120 x 150mm belt length 7050mm engine 3kW exhaust port diameter 120mm weight 400kg PRODUCT FEATURES The Optimat SD 260 long belt sander has been designed for processing smaller and medium-sized elements. The electrically controlled table certainly increases the precision and efficiency of work. Standard equipment: Electric table height adjustment Extraction nozzle User manual Automatic engine braking Protections compliant with standards Ergonomic emergency switch Electronic table stops Net price: PLN 21,000 Net price: EUR 5,000 Net price calculated according to the exchange rate of PLN 4.2/EUR (in case of larger exchange rate fluctuations, the price may change)

Condition: excellent (used), CATALOGUE NUMBER 8021 TECHNICAL DATA Hjdpoztaqasfx Anyju - max. width of the workpiece: 1100 mm - max. height of the workpiece: 150 mm 2 units: 1) grooved rubber roller for calibrating 2) grooved rubber roller - motor power: 11 kW - brake - from above: - split, sliding metal roller - pressure roller - unit - pressure roller - unit - pressure roller - cleaning brush - from below: - 2 sliding metal rollers - conveyor belt - 2 sliding metal rollers (outlet) - new conveyor belt - pneumatic belt oscillation - electric table lifting - stepless feed speed adjustment - feed motor: 1.5 kW - grinding thickness potentiometer - working pressure: 8-10 bar - dust extraction nozzle diameter: 3x165 mm, 1x140 mm - overall dimensions (L/W/H): 1870x1850x2210 mm - weight: 2165 kg ADVANTAGES - Made in Italy, SCM brand - New conveyor belt - 2 units - Grinding thickness potentiometer - Unpainted - Used sanding machine, very good condition Net price: 26900 PLN Net price: 6405 EUR, depending on the exchange rate of 4.20 EUR (Prices may vary due to higher fluctuations)

Condition: new, Year of construction: 2026, functionality: fully functional, load capacity: 3,000 kg, Column Lifting Rotating Device with 3-Ton Capacity Protec Syncrolift Rotating Device/Positioner Double Column, Wireless and Manual Remote Control Column Adjustment with Two Travel Modes Load Capacity 3000 kg, 360° Minimum Working Height: 600 mm Hjdpfxswih Dco Anyou Maximum Working Height 1500 mm Speed 0.5 rpm Clamping Plate Diameter 600 mm Rotation 0.75 kW Torque 5180 N-m 2 to 10-Ton Capacity Available Upon Request

Condition: excellent (used), Year of construction: 2009, Vertical glass washing machine Working height: 1500 mm Open top Glass thickness: 2 - 13 mm Working direction: from right to left Washing machine consists of: - 2 brushes (1 pair), - 2 pcs. of air knives, - 1 stainless steel water tank separated in 3 parts (1 part with water heating), - motorized inlet and outlet conveyors, - outlet conveyor is with inspection lamps. The speed of movement of the conveyor is regulated by inverter Hedpfsy Na Rnjx Anyou Total floor dimensions: L 4900 x W 1500 x H 2650 mm Very good and clean condition Good working order, tested See video As is Available immediately

Condition: used, Year of construction: 1996, functionality: fully functional, machine/vehicle number: S/70032, grinding width: 1,360 mm, power: 49 kW (66.62 HP), height adjustment type: electric, The refurbished automatic wide-belt sanding machine is designed for calibrating and final sanding of solid wood. This model belongs to the higher range of automatic wide-belt sanding machines, characterized by an exceptionally rigid frame, top-quality sanding performance, and versatile applications. Main components: 1. Steel roller – 15 kW 2. Hard rubber roller – 15 kW 3. Mechanically adjustable platen – 11 kW + Brushing/cleaning unit at the outlet (without tooling). Sanding width 1360 mm Working thickness 3 – 160 mm Motorized adjustment of working thickness with LCD display Automatic centering of the feed belt Total maximum power consumption 49.8 kW Conveyor in good condition CE safety standard Hsdpfx Ansz D Ufdoyou Weight approx. 4000 kg

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1998, operating hours: 1,571 h, load capacity: 3,000 kg, fuel type: electric, battery capacity: 240 Ah, battery voltage: 24 V, fork length: 970 mm, front tire type: cushion tires (black), rear tire type: cushion tires (black), overall weight: 664 kg, total length: 1,650 mm, total width: 1,150 mm, fuel: electricity, STILL WAGNER EGU 3000 – Electric low-lift pallet truck TECHNICAL DATA Lifting capacity: 3.000 kg Fork length: 970 mm Drive: Elektro 24V Battery: 24 V 240 Ah v. 1998 Charger: ohne/without Tyres: Bandagen Service weight: 664 kg Hedpfjz Apvdsx Anyju Length: 1.650 mm Width: 1.150 mm Year of manufacture: 1998 Operating hours: 1.571 h Condition: working condition Internal no.: 1308670 Location: 14974 Ludwigsfelde bei Berlin Unilift GmbH & Co. KG – inspected used forklifts from Ludwigsfelde near Berlin.

Condition: excellent (used), Year of construction: 2012, functionality: fully functional, clamping force: 1,500 kN, screw diameter: 50 mm, clearance between the columns: 520 mm, overall weight: 6,500 kg, Clamping force: 150 t Year of manufacture: 2012 Injection shot weight: 359 g Injection unit 800 Screw diameter: 50 mm Specific injection pressure: 2000 bar Injection volume: 392 cm³ Injection shot weight: 359 g Screw L/D ratio: 24 Tool closing unit 1500 Clamping force: 150 t Tool plate dimensions: 695 x 695 mm Hjdpfxsz D U Tnj Anyeu Distance between columns: 520 x 520 mm Tool height: 250...650 mm Opening stroke: 400 mm Maximum plate distance: 650...1050 mm Weight: 6500 kg Dimensions (m) L x W x H: 5.25 x 1.67 x 2.20 m Control system: Selogica Equipment: Hydraulic core 12-zone hot runner system Accumulator Frequency converter Hidrive drive 4 x pneumatic valve

Condition: good (used), electric motor, three-phase motor -Manufacturer: Wap, electric motor type AP 1112M-4 -Power: 4 kW -Speed: 1440 rpm -Shaft: Ø 28 x 60 mm Hsdpfjz D Sruox Anysu -Design: B3 -Protection class: IP 44 -Dimensions: 415/320/H225 mm -Weight: 51.8 kg

Condition: used, For sale: ENORM PRIMO – TOP CONSTANT THICKNESS MACHINE / automatic head positioning Hedpfx Ansz D S Rdoysu Wide-belt calibrating and fine-finishing machine Combined unit: contact roller and pneumatic sanding pad Enormatic Digital thickness display for workpiece thickness Belt drive motor power approx. 9 kW Contact roller pressure adjustable in infinitely variable steps according to grit scale Infeed and outfeed table with roller support Working width 1100 mm Feed rate 2.5 - 15 m/min Machine is WORKSHOP OVERHAULED and in VERY GOOD CONDITION Machine comes from a craft business Available from stock in Lieboch

Condition: used, operating hours: 11,562 h, total height: 1,900 mm, total length: 5,600 mm, total width: 2,000 mm, Empty weight: 8.500 kg Price: On request - Documentation available: No - CE certificate present: No - Operating hours: 11562 Hjdpewp H Efjfx Anyeu - Drive system: Conventional - Power [kW]: 30.0 - Centre height [mm]: 500 - Swing over bed [mm]: 1000 - Distance between centres [mm]: 3000 - Spindle bore [mm]: 105 - Min. spindle speed [rpm]: 2.24 - Max. spindle speed [rpm]: 450 - Transport dimensions: 5600mm x 2000mm x 1900mm (l x w x h) - Transport weight [kg]: 8500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: like new (used), functionality: fully functional, CMU Shear 3000 x 8/10 Model 2E0 6/30 Motorized Backgauge Blade Angle Adjustment Used Machine Hedpfxjy R Diws Anyou Internal Code: SER 63

Condition: good (used), Year of construction: 1999, Ref. -No.: 10365 Manufacturer: MONFORTS Type: KNC 8 S - 3000 Year of construction: 1999 Type of control: CNC-Steuerung Control: MTC K Storage location: Halberstadt Country of origin: Deutschland Machine-No.: 178.05 X stroke: 455 mm Z - stroke: 2850 mm Chuck diameter: 315/400/500 mm Centre Distance: 3000 mm Feed Capacity - Z: 23,9 kN Feed Capacity - X: 11,3 kN Rapid Travel Speed X-Axis: 6,8 m / min Rapid Travel Speed Z-Axis: 4 m / min Circumferential diameter over radial slide: 540 mm Max swing diameter: 830 mm travel of the cross slide: 450 mm Spindle head max. passage for violent material: 88 mm Spindle head max. passage for bare material: 90 mm Tailstock outside diameter of the quill: 125 mm Tailstock maximum quill stroke: 200 mm Tailstock inner cone: MK6 Type hydraulic tank: 15 L. coolant reservoir: 220 L. Coolant tank at chip conveyor: 160 L. Hsdpfezx Nxdsx Anyeu Machine length: 5200 mm Machine width: 2110 mm Machine Height: 1995 mm Weight Of The Machine Ca.: 6,850 (Ohne Späneförderer und Kühlmittelbehäter) t Headstock Spindle Head: DIN 55027 - 11x290 Further information: Additional lubricating oil tank approx. 6l incl. tools Machine is under power and can be inspected by arrangement.

Condition: new, Year of construction: 2026, functionality: fully functional, working width: 600 mm, brushing unit diameter: 150 mm, height adjustment type: electric, working height: 300 mm, power: 5.5 kW (7.48 HP), Brushing machine Houfek Twingo 600 BB 400V/50Hz, 2x5.5 HP (4 kW), width 600 mm Basic equipment: Hodpeu Rnb Nefx Anyju 1.1 Motor 4 kW (5.5 HP) per B-unit 1.2 Tool turning diameter 120-300 mm, working length 600 mm 1.3 Independent height adjustment of the working units 0 - 300 mm 1.4 Fixed table h=900 mm 1.5 Expansion shaft D=40 mm 1.6 Two rubberized pressure rollers on the work unit, height-adjustable 1.7 Electric stroke of the work unit(s) + scale with unit height indicator 1.8 Two feed belt speeds 4.5/9 m/min - replaced by P81 10 1.9 Brush protection cover 1.10 Suction nozzle diameter for unit B and Q D=120 mm 1.11 Machine is not equipped with the tool for 2nd unit 1.12 Voltage 400V/50Hz 1.13 Packed in PE film as standard 1.14 Machine built according to CE power and safety standards Additional equipment installed in this machine: - 2x motor 5.5 kW 7.5 HP - Automatic feed belt centering - Frequency converter for feed belt speed 3 - 15 m/min - Oscillation for one brush unit with the possibility of switching off - 2x return of the main motor (1 unit) (synchronous and counter-rotation possible on both units)

Condition: used, Year of construction: 1984, Working width 1350 mm Number of sanding units x st. Used Machine Year of manufacture: 1984 Condition: fully inspected and serviced Features and Technical Specifications: - Includes a combination unit with a contact roller and grinding shoe - With height-adjustable contact roller for calibration Hedpfx Anjzlbpnsyju - With workpiece-controlled air-cushion pressure shoe - 4-way adjustable grit compensation - With pneumatic belt tensioning device - With a rotating texturing brush on the machine’s outlet side - Sanding width: 1350 mm - Sanding belt length: 1900 mm - Clearance height: 150 mm - Main motor: 15 kW - Feed speed continuously adjustable from 2.5 to 12.5 m/min - With roller table at the infeed - With separate additional texturing brush - With roller table at the outlet - With digital display for the electrically driven workpiece thickness adjustment - With automatic workpiece thickness adjustment - Exhaust ports: 2 x 200 mm - Feed belt is in good condition; has one defect (see photo) Dimensions: approx. 2300 x 2000 x 2300 mm Weight: approx. 2500 kg The photos show the machine as it was upon receipt Availability: immediately Location: Röllbach

Condition: new, 0 ja Working width 3000 (3500) mm 0 ja Ruchser RU-BM-3000 (option: 3500) Wing assembly table ----- Herstellerbeschreibung: Item 1.0 Article 0610000 RU-BM-3000 Sash assembly table, for sashes up to max. 2500 mm height with RU-SH, special screwdriver length 3000 mm, width 1400 mm, inclination of working platform manually adjustable. Usable width 2500 mm Holder for hardware shears or hardware punch. 10 swivel-mounted pendants for hanging the sashes, completely pneumatically foldable for unhindered movement of the sashes on the table surface. Device for scanning the sash fitting length for constant and variable/centered handle fit and any handle fit height for pre-drilled sashes, colour-coded dimension recognition for the fittings. Pendulum height can be set to 50 or 60 mm on one stop. RU-SH, special screwdriver with pneumatic depth cut-off mounted on carriage, safety control, pneumatic height adjustment, screw feeder with automatic switch-off of the filling container manual insertion for a second screw length on the special screwdriver, accessories. RA-8, turret stop for 8 screw levels mounted on the carriage. RA-4 commuter rail manually adjustable in depth against left and right one 4-fold turret stop each. PSF - Pneumatic clamping device for sashes against the lateral stops. Working height adjustable from 900 - 1000 mm. Please specify whether felt, sliding or brush strips should be used as a support. Item 1.1 Article 6315 RU-BM-... adjusted to customer's fitting specification Item 1.2 Article 0500000 Holder adjusted to customer punching press/ shear For mounting a customer-supplied punching press or shear (other manufacturer) on the sash assembly table. Please specify make when ordering !!! ----- Hedpfx Anst Tq Aaoyju Price RU-BM-3000 in the above version ex works: on request! ----- Fitting bearing options for RU-BM-3000: ----- Version with fixed fitting bearing: Price EUR 5.468,00 Article 0630000 RU-BL-30/30 Fixed fitting storage unit Mounted above the leaf assembly table Length 3100 mm, depth 1250 mm, with 3 shelves with 10 compartments each, divided by partitions. Freestanding version: Price EUR 6.017,00 Item 0710000 RU-SBL3000/30 Freestanding storage unit, Length 3100 mm, depth 1250 mm, height 2050 mm, upright frame on the front without supports, 30 compartments, 10 in a row, each divided by partitions and a continuous shelf at the top, size of the compartments: width 280 mm, height 150 mm 4 pcs. Angle supports for corner deflections: Price 609,00 EUR Side length 120x120mm; inclination approx. 3° The front edge of the angles is bent up 5mm to prevent accidental unloading. 2 pieces on the left and 2 pieces on the right under the first shelf of the fitting. ----- Surcharge for RU-BM-3500 ----- Article 0610300 RU-BM-3500 Sash assembly table for sashes up to max. 3000 mm height with RU-SH, special screwdriver length 3500 mm, width 1400 mm, inclination of working platform manually adjustable.usable width approx. 3000 mm Surcharge RU-BM 3500 to RU-BM 3000: EUR 2,811.00 Fitting bearing for RU-BM-3500 (only free-standing possible): Price EUR 6,665.00 Item 0710007 RU-SBL3800/36, free-standing fitting storage Length 3800 mm, depth 1280 mm, height 2060 mm...

Condition: new, Made in Italy Machine manufactured according to DIN 8606 Maximum turning height: 260 mm Turning diameter over bed: 520 mm Turning diameter over slide: 300 mm Distance between centers: 1,500 mm Bed width: 400 mm Spindle bore: 82 mm Spindle nose: Camlock 8" Spindle speeds: (24) 9 - 1600 rpm (Option 11 - 2000 rpm) Motor power: 5.5 kW (Option: 7.5 kW) Feed rate, Z-axis: (93) 0.028 - 6.43 mm/rev Feed rate, X-axis: (93) 0.012 - 2.73 mm/rev Threads, metric: (54) 0.5 - 224 mm Threads, Whitworth: (55) 72 - 1/8 TPI Threads, module: (54) 0.5 - 112 mm Threads, diametral pitch: (54) 64 - 1/4 D.P. Cross slide, WxL: 650 x 230 mm Cross slide travel: 340 mm Top slide, WxL: 350 x 150 mm Top slide travel: 150 mm Tailstock spindle diameter: 85 mm Tailstock spindle travel: 200 mm Tailstock taper: MK 5 Weight: approx. 3,100 kg Equipment: - Tailstock movement with pneumatic assistance - Acceptance test report according to DIN 8605, lathe with increased accuracy - Mechanical dual clutch - Electromagnetic brake - Rapid traverse for X and Z axes - Electrical equipment made of high-quality brand components, e.g. Siemens/Schneider - Lubrication of guide rails via hand pump - Reducing sleeve - 2 fixed centers Hodpfx Ansdvm Eueyeu - All safety devices according to CE standards: Chuck guard with plexiglass pane, secured with microswitches. Tool holder guard with plexiglass pane. Rear splash guard over the entire length. Lead screw and feed screw protection by means of a light curtain (integrated into the emergency stop circuit). Emergency stop button. - Chip tray on wheels - Electric coolant system - Fixed steady rest - Follower steady rest - Operating tools, acceptance test report according to DIN, operating and maintenance manual, complete electrical installation, machine manufactured according to the latest CE standard

Condition: new, Maximum turning height: 250 mm Hsdpfxjgt E Ilj Anyou Turning diameter over slide: 350 mm Turning diameter in the curve: 695 mm Distance between centers: 1500 mm Spindle nose: DIN 55029, cam lock, size 6 Bed width: 305 mm Cross slide travel: 272 mm Top slide travel: 155 mm Spindle bore: 80 mm Speed range, stepless: (3) 30 - 2200 rpm Whitworth threads: (45) 2 - 72 TPI Metric threads: (39) 0.2 - 14 mm Diametral threads: (21) 8 - 44 D.P.I Module threads: (18) 0.3 - 3.5 module Longitudinal feeds: 0.04 - 1.00 mm/rev Cross feeds: 0.02 - 0.50 mm/rev Motor power: 5.5 kW Dimensions L x W x H, approx.: 2900 x 1175 x 2040 mm Weight, approx.: 2,200 kg Features: - Toolmaker's precision - Stepless speed control (3 pre-selected stages) - Finely balanced main spindle - Stable machine bed with hardened and ground guideways - One-piece cast iron base - Adjustable precision tapered roller bearings in the main spindle - Easy-to-operate feed drive with a large feed range, running in a closed oil bath. - Low-maintenance central lubrication system - Removable bridge - CE Equipment: - 3-axis digital display (resolution 0.005 mm) - Frequency inverter - Machine stand with a high splash guard and integrated lighting - Chip tray that can be pulled out to the front - 3-jaw chuck - Fixed steady rest - Traveling steady rest - Micrometer bed stop - Oil cooler - Two emergency stop push buttons and a foot pedal with an electrical braking system - End-switch protected chuck guard, tool holder guard, and cover for the lead and feed screw according to European safety standards CE - Coolant system - Fixed center - Reduction sleeve for the main spindle - Operating tools in a toolbox

Condition: good (used), Year of construction: 2007, operating hours: 52,506 h, functionality: fully functional, punching force: 180 t, sheet thickness (max.): 6 mm, travel distance X-axis: 3,070 mm, travel distance Y-axis: 1,660 mm, punching diameter: 76 mm, workpiece weight (max.): 230 kg, overall weight: 16,000 kg, feed rate X-axis: 90 m/min, feed rate Y-axis: 60 m/min, space requirement width: 6,800 mm, space requirement length: 7,600 mm, space requirement height: 2,500 mm, Equipment: safety light barrier, Special equipment: + MultiShear function + MultiTool function + Brush tables Standard equipment: - Safety light barriers - 3 clamping claws - Rotation of all tools - NC-controlled, digital, maintenance-free three-phase drives - Automatic repositioning - Tool length compensation - Small parts chute 500x500 mm - Punching slug extraction - Tool spray lubrication - Automatic tool change - Programmable punching tool lubrication with 2 containers - Programmable stripper - Network interface RJ34 - 3.5" floppy disk drive - TOPS 2000 graphics programming - Online diagnostics via modem Hedoz En Iuopfx Anyeu - Operating manuals.

Condition: used, Year of construction: 1995, Technical details: sheet width: 1500 mm plate thickness: 1 mm control: Ducter 1500 total power requirement: 2,0 kW CROSS/TRANSVERSE PART PLANT consisting of: Reel straightening machine and shears Shears: - cutting length 1500 mm - sheet thickness approx. 1.0 mm - operation via control panel and foot control - manual operation / automatic - table size 1530 x 400 mm - Rear end stop: adjustment range 1300 mm - Size: LxWxH: 1600 x 2.0 x 1350 mm Straightening system: - stand width 1585mm - Table size 1700 x 700mm with side stop 1x fixed and 1x adjustable (manual) - 2 pcs. infeed rollers, revolving, Ø 50 x 1670mm - Straightening rolls: 2x opposite draw rolls (2x top/2x bottom) both driven, adjustment path 10mm vertical - continuous rollers: 3x top running, manual adjustment 8mm vertical and 4x bottom driven, fixed - Size: LxWxH: 1580 x 2050 x 1260mm Unwinding reel: - manual operation/handling - Spread max. Ø 520mm - Size: LxWxH: 550 x 800 x 1550mm Hedpeu Tp N Dsfx Anyju The machine has a manual counter. accessories: - 1 pc. spare blade (must be regrinded) *

Condition: used, Brushing machine / brush deburrer - make Lindemaier, year 1990, power consumption 7,5 kW, dimension: L:1,0 x W:0,80 x H:1,25m, weight approx. 48 kg - brush size Ø 300 x Ø 50x50mm type K 180 - engine speed 2920 rpm, suction nozzle Ø 180mm - with blow-off device Accessories: approx. 15 spare brushes NEW Hodpou Nu Rnjfx Anysu *

Condition: used, Technical details: welding current: 330A / 50% und 210A / 100% protection class: IP 23 total power requirement: 13,8 kVA Hodpfxju Nxv Is Anyou weight of the machine approx.: 71 kg dimensions of machine: 0,95 x 0,60 x 0,90 m - MIG / MAG / MIG and electrode - cooling method water-cooled AF - insulation class B - power range 3A / 20V to 330A / 34V - wire feeder DS III (wire Ø 0,8 - 1,6mm) optinal possible! Steuerung über Roboterinterface *