Used Huvema Tryout Press - Hydraulic for sale (24,591)

Condition: used, Pneumohydraulic cylinder TOX Pressotechnik Hydro-pneumatic press, power pack Type: S 04.00.050.12 D No.: 208696.460 Year of manufacture approx. 2000 Pressure capacity: 4.0 tons at 10 bar Pressure capacity: 3.0 tons at 8 bar Pressure capacity: 2.6 tons at 7 bar Pressure capacity: 2.4 tons at 6 bar Pressure capacity: 2.0 ton. at 5 bar Pressure capacity: 1.6 ton. at 4 bar Pressure capacity: 1.2 tons at 3 bar Total stroke: 50 mm Power stroke: 12 mm Piston rod: Ø 30 mm Thread for piston rod: M22 x 2 mm Compressed air requirement: 3 to 10 bar - Electronic oil pressure switch with TOX digital display for force measurement, type 167282 - Height only power pack with piston rod = 610 mm - Height of power pack hydropneumatic cylinder only = 560 mm - Additional base plate 160 x 160 x 20 mm - Plunger plate: Ø 68 mm Space requirement L x W x H: 160 x 160 x 660 mm Rjdpfx Aju D Tz Ujmmeu Weight: 21 kg Very good condition 3 pieces available, price per piece

Condition: used, Single-column hydraulic press MAE type S63SZ SO Redodzp Trjpfx Ammeu . 551277 Year of manufacture approx. 1977 Nominal pressing force: 63 tons Pressing force: 50 tons (practically tested) Throat depth: 320 mm Table area: 850 x 630 mm Ram area: 1050 x 500 mm Ram stroke: 500 mm Max. installation height: approx. 730 mm Table height above floor: 970 mm Hydraulic tank capacity: 600 liters Drive power: 15 kW Power supply: 380 Volt, 50 Hz - Hydraulic draw cushion below the table with bores through the tabletop - Two-hand operation - Electrical control cabinet damaged Required space (L x W x H): 2000 x 1200 x 3420 mm Weight approx. 5 tons The machine is operational, the control cabinet is mechanically damaged. During test run, the machine achieves a pressing force of 50 tons, presumably a pressure relief valve is venting.

Condition: used, Single-column hydraulic press with draw cushion RÖCHER Type REP 100.01 SZ Hydraulic deep-drawing press Machine No. 15.499 Year of manufacture 2003 Pressing force: 100 tons Ram stroke: 500 mm Throat depth: 370 mm Installation height: 600 mm Table surface: 850 x 700 mm with a drop-through hole Ø 150 mm Ram surface: 700 x 600 mm Ram ejector force: 16 tons (160 kN) Ram ejector stroke: 100 mm Ram ejector with internal thread M24 x 1.5 mm Draw cushion force: 40 tons (400 kN) Draw cushion stroke: 200 mm Draw cushion area: 530 x 530 mm Pressure holding time: 0 to 90 sec. Table height above floor: 910 mm Hydraulic operating pressure: max. 300 bar Hydraulic tank capacity: 700 liters Rodpeyupulsfx Ammju Approach speed (rapid traverse): approx. 400 mm/sec. Pressing speed up to 23.8 tons (238 kN): 5 to 68 mm/sec. Pressing speed up to 100 tons (1000 kN): 5 to 16 mm/sec. Return speed: 50 to 400 mm/sec. Main pump drive power: 18.5 kW Auxiliary pump drive power: 4 kW Power supply: 400 Volt, 50 Hz (63 Amps) - Operation and programming via PC 670 touch panel, keyboard and mouse - Machine control via SIEMENS S7-300 PLC system - Ram stroke and press force programmable via control system - Draw cushion with drawing and ejector function - Draw cushion force infinitely adjustable - Ram and draw cushion equipped with direct linear measurement system - Draw cushion can be moved in and out under the press area, for punching work using the drop-through hole - Floor-level installation, draw cushion does not penetrate the floor - Pressure and stroke cutoff - Fixed stop with indirect measurement system - Pressure holding time infinitely programmable - Table with holes for the draw cushion ram rods - Ram with ejector - Knock-out damping - Stroke triggering via two-hand operation, foot switch, hand lever and push button on the control panel - LEUZE light barrier as reach-in protection for safety operation - Front mirror columns on the press table can be shifted laterally - Electrical control cabinet mounted on machine frame - Hydraulic oil cooler with fan motor (oil-air cooling) - Manual central lubrication pump - 2x hose connections for tool tempering or cooling at the ram - Piece counter in the control system - 306 read operating hours - Operating manual, hydraulic diagram, and electrical diagram available Space requirements (L x W x H): 3100 x 1800 x 4160 mm Weight: approx. 13 tons Very good condition, as new

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale Rsdpfx Amevq Rtkomou - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Hydraulic notching machine with adjustable angle SIMASV model AV 220-6PA Serial no.: C1524 Year of manufacture: 1996 Blade length: 220 mm Material thickness (steel): 6 mm Material thickness (stainless steel): 4 mm Table dimensions: 950 x 790 mm Table height: 940 mm Motor power: 3 kW Power supply: 400 Volt, 50 Hz - Operation via push-button or foot switch - Adjustable notching angle from 30° to 140° - Angle adjustment via 2 handwheels (right and left) - Hydraulic clamping for the adjustable blades - Electric foot switch - 2 adjustable stop rails with angle scale - Multiple millimeter scales integrated into the table top - HSS blades newly ground, as new Required space (L x W x H): 1000 x 950 x 1470 mm Weight: 750 kg Rjdpfxsrzfh Hj Ammju Very good condition

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet - 2-hand control panel adjacent - ground level installation Rsdpedzp Tcefx Ammeu - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: good (used), Year of construction: 2007, frame press GOMA PHA 3500 Door Press hydraulic Location Gorzów Wlkp. Conditions of delivery Rjdpfx Aodntc Njmmsu OWN RECEIVING Cost of delivery to be negotiated Startup type to be negotiated Description Comments Working space 3500 x 2300 mm 1000kG (daN) pressure, engine at hydraulic unit 2,2 kW lenght 3500 mm hight 2300 mm weight 2000 kg agrageate hydraulic

Condition: good (used), Year of construction: 1970, pressure 80 t passage width 350 mm stroke 600 mm Rjdpfx Amevwgqromju table dimension - longitudinal 400 mm dimensions of the machine ca. 1400 x 1050 x 2350 m

Condition: used, Year of construction: 2003, functionality: fully functional, machine/vehicle number: 3599, total height: 2,600 mm, total length: 2,200 mm, total width: 2,200 mm, overall weight: 16,300 kg, pressing force: 100 t, passage height: 1,200 mm, passage width: 1,200 mm, Hydraulic press (previously used for lamination of door panels) Pressing area: 1300x1100 mm Press cylinders: 4x D110 mm Maximum pressing force: 1000 kN The machine is currently disassembled and was fully operational until it was taken apart. For an additional charge, two compatible heating plates including control cabinet are also available. Rodjwt Axcspfx Ammsu

Condition: good (used), Manufacturer: WMW Zeulenroda Type: PYE 160 SS Year of manufacture: 1980 Redpswp Nv Hefx Ammou C-frame construction Die height 850 mm Thickness bolster plate 100 mm Throat C side 360 mm Specifications Metric US Standard Capacity 160,000 Table length 1,250 mm Table width 600 mm Ram stroke 500 mm Starting speed 100 mm/min Working speed 10 mm/min Return speed 125 mm/min Power 22.5 kW Dimensions (Estimate) Length: 2,150 mm Width: 1,250 mm Height: 3,600 mm Weight: 7,500 kg Please note: The information on this page has been provided to the best of our knowledge and, where possible, from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not represent a warranty or contract terms. We recommend you check all important details.

Condition: good (used), Make: Ursviken Type: VPF 1000/800-5,0 Control: Siemens Simatic panel Year: 1970 Hydraulic press for fabrication off large componts like dish heads tanks boiler shipyard and steelconstruction Renewed in 2015 with Siemens SIMATIC panel and E-Cabinet Rittal Build in height 2950 mm Maximum die height 1500 mm Movable Table & Piston in X-Ways Large package Die tooling radius 10/20/30/50/60/80/100 Pressing force 210 kg/cm2 Maximum stroke 800 mm Machine 2350 mm placed in ground Specifications Metric US Standard Capacity Kg 1000 Ton Distance between column 5010 mm Table Length 3000 mm Table Width 2000 mm Table Height 550 mm Rodpfx Askvmi Semmsu Ram stroke 1450 mm Approche speed 50 mm/min. Working speed 5 mm/min. Return speed 50 mm/min. Dimensions (Estimate) Length 0 mm Width 0 mm Height 0 mm Weight 0 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 1991, Distance between column:1870mm Rjdswyuqkepfx Ammsu Hight under roof: 1400mm Table Length: 1600mm Length: 3400mm Width: 3400mm Height: 3500mm Weight: 19000kg

Condition: excellent (used), Year of construction: 2006, Table size 3500 x 2500 mm Siemens Simatic OP7 controller Max. work load 80 Ton New price 1 Mil EUR Working force up to 250 Bar Power 30 kW Distance between column:3700mm Hight under roof: 2650mm Table Length: 3500mm Ram stroke: 2100mm Rodjxam Sdjpfx Ammou Approche speed: 80mm/min. Working speed: 8mm/min. Return speed: 50mm/min. Length: 7800mm Width: 5500mm Height: 6510mm Weight: 135000kg

Year of construction: 2002, condition: ready for operation (used), Press force: 1800kN, stroke: 300mm, strip width: 80-400mm, max. coil weight: 3t, system operating pressure: 250bar, pump drive power: 15kW. An inspection on site is possible. Rodey Sncwspfx Ammsu

Condition: used, Double column press - Hydraulic Manufacturer REPKON Model 2000/800 kN Condition used description Pressure 200 t Column width 1600 mm ram stroke - max. 600 mm Installation height 900 mm Table width 1600 mm Rsdpfx Amoudb Hcomeu Table depth 1300 mm Table height 1060 mm ram surface 1600 x 1300 mm T-slots Din 650 / 22H12 Rapid traverse 400 mm/s Return speed 325 mm/s Pressing speed 42 mm/s at 40% mm/sec Pressing speed 20 mm/s at 100% mm/sec Die cushion pressure 800 kN Die cushion stroke 150 mm Die cushion speed to 68/ from 225 mm/sec Conversion year: 2001

Condition: new, functionality: fully functional, power: 11 kW (14.96 HP), pressing force: 30 t, stroke length: 300 mm, table width: 500 mm, table length: 700 mm, clearance between the columns: 400 mm, total width: 2,292 mm, total height: 3,760 mm, Equipment: CE marking, This offer concerns a new machine that is currently still in production. - Control system: SIEMENS S7-1500 - Table specifications: T-slots/holes according to customer requirements Rsdey Rzchspfx Ammju - SIEMENS SIMATIC 9-inch LCD touchscreen - Electrical components from Siemens, Allen Bradley, Phoenix, Sick - Machine painting/finishing to customer specifications available - 1-year warranty on electrical and hydraulic components - 2-year warranty on mechanical equipment and structure

Condition: ready for operation (used), Year of construction: 1998, power: 37 kW (50.31 HP), pressing force: 250 t, stroke length: 150 mm, table width: 900 mm, table length: 1,000 mm, overall weight: 16,000 kg, Very nice and well maintained hydraulic press. 250 tons pressing force. Redpfxsry Trpe Ammeu Approximate dimensions: H: 380 cm. W: 200 cm. L: 200 cm. Weight: 16,000 kg. Can be loaded by crane on collection against payment. Transportation can be arranged. Sold for customers. Location: DK-7600 Struer. Make an appointment for a demonstration.

Condition: good (used), Year of construction: 1993, functionality: fully functional, Hand insertion safety – Pressing force up to 100 kN Throat depth: 210 mm Table size (W x D): approx. 500 x 400 mm Installation height with/without clamping plate: 300 mm Stroke: 100 mm Redpfoy St I Sex Ammsu Total power: 2.5 kW Weight: approx. 2.5 t Oil fill: approx. 150 l Required space (W x D x H): approx. 0.95 x 1.5 x 1.95 m Equipment and delivery scope: Switch-over between travel / pressure Pressure control valve with gauge display Adjustable dwell time Documentation

Condition: good (used), JDS hydraulic press Rjdpfxjiki Ahe Ammju Bed: 505 x 510 mm Dimensions: 140x140x285 cm LxWxH

Condition: new, functionality: fully functional, Year of construction: 2026, input voltage: 400 V, Hydraulic C-Frame Press Our hydraulic C-frame press is a professional machine designed for precise and demanding machining operations. Thanks to its C-frame construction, it provides easy access to the working area, allowing the processing of larger components and convenient handling of material from different sides. Key Features High pressing force – ideal for bending, straightening, pressing, and assembling components. C-frame construction – improved ergonomics and excellent accessibility to the working area. Solid steel frame – ensures durability and safe operation. Precise hydraulic control – smooth adjustment of force and operating speed. Industrial and workshop applications – perfect for both large manufacturing plants and smaller workshops. Thanks to its versatility and robust construction, this press is suitable for many industries, from automotive and metalworking to technical service centers and tool shops. Specifications Pressing force: 250 kN (approx. 25.5 tons) Maximum pressure: 25 MPa Redpfx Ajyr Ek Rjmmju Maximum opening: 500 mm Stroke: 200 mm Table dimensions: 500 × 400 mm Throat depth: 200 mm Downward speed: 10 mm/s Return speed: 14 mm/s Motor power: 3 kW

Condition: new, Year of construction: 2026, machine/vehicle number: PRASA HYDRAULICZNA TYPU C HPW 50 50 TON, functionality: fully functional, input voltage: 400 V, pressing force: 51 t, stroke length: 200 mm, table width: 400 mm, table length: 500 mm, pressing speed: 18 mm/s, Hydraulic C-Frame Press Our hydraulic C-frame press is a professional machine designed for precise and demanding machining operations. Thanks to its C-frame construction, it provides easy access to the working area, allowing the processing of larger components and convenient handling of material from different sides. Key Features High pressing force – ideal for bending, straightening, pressing, and assembling components. C-frame construction – improved ergonomics and excellent accessibility to the working area. Solid steel frame – ensures durability and safe operation. Precise hydraulic control – smooth adjustment of force and operating speed. Industrial and workshop applications – perfect for both large manufacturing plants and smaller workshops. Thanks to its versatility and robust construction, this press is suitable for many industries, from automotive and metalworking to technical service centers and tool shops. Specifications Rsdpfxoyr D R Ne Ammeu Pressing force: 500 kN (approx. 51 tons) Maximum pressure: 25 MPa Maximum opening: 500 mm Stroke: 200 mm Table dimensions: 500 × 400 mm Throat depth: 200 mm Downward speed: 19 mm/s Return speed: 18 mm/s Motor power: 4 kW Delivery to the customer is possible. The delivery cost is determined individually according to the quotation of the transport company. If you are interested in other machines, we encourage you to visit our website.

Condition: new, functionality: fully functional, Year of construction: 2026, input voltage: 400 V, Hydraulic C-Frame Press Our hydraulic C-frame press is a professional machine designed for precise and demanding machining operations. Thanks to its C-frame construction, it provides easy access to the working area, allowing the machining of larger components and convenient handling of materials from different sides. Key Features High pressing force – ideal for bending, straightening, pressing, and assembling components. C-frame construction – improved ergonomics and better access to the working area. Solid steel frame – ensures durability and operational safety. Precise hydraulic control – smooth adjustment of force and operating speed. Industrial and workshop applications – suitable for both large manufacturing plants and smaller workshops. Thanks to its versatility and robust construction, this press is suitable for many industries, from automotive and metalworking to technical service centers and tool shops. Specifications Pressing force: 1000 kN (approx. 102 tons) Maximum pressure: 25 MPa Maximum opening: 600 mm Stroke: 300 mm Table dimensions: 700 × 500 mm Throat depth: 250 mm Downward speed: 11 mm/s Return speed: 25 mm/s Rodeyrr Rkspfx Ammju Motor power: 5.5 kW Delivery to the customer is possible. Shipping cost is calculated individually by the transport company.

Condition: excellent (used), Year of construction: 1988, machine/vehicle number: 119, functionality: fully functional, power: 11 kW (14.96 HP), input voltage: 380 V, input frequency: 50 Hz, pressing force: 30 t, stroke length: 700 mm, table width: 500 mm, table length: 700 mm, clearance between the columns: 680 mm, total length: 2,100 mm, total width: 1,800 mm, total height: 3,500 mm, overall weight: 3,000 kg, Equipment: safety light barrier, Well-maintained 4-column hydraulic press from a facility closure. The machine is fully functional and was in production use until recently. Rsdpfx Aey Sglwjmmju It has been modernized and features an overhauled digital Siemens control system. Additionally, it is equipped with a safety enclosure and SICK brand light curtains. The machine is currently in storage but is available for inspection upon request.

Year of construction: 1961, condition: ready for operation (used), A hydraulic single-column C-frame press Müller is available. Press force: 63t, stroke: 560mm, throat depth: 325mm, installation height: 700mm, table dimensions X/Y: 640mm/640mm, ram surface: 560mm/560mm, machine dimensions X/Y/Z: approx. 2000mm/1200mm/3100mm, weight: approx. 7500kg. The machine has a motor malfunction. An on-site inspection is possible. Rsdpfxoy Rtg Ee Ammju

Condition: used, Year of construction: 1967, total length: 2,000 mm, total width: 1,750 mm, total height: 2,850 mm, Colour: Grey Empty weight: 6.000 kg - Year: 1967 - Documentation available: No - CE certificate present: No - Serial number: 1166 - Drive system: Conventional Redpfox N Sxdjx Ammsu - Press force [ton]: 100 - Max. stroke [mm]: 250 - Table length [mm]: 740 - Table width [mm]: 500 - Ram length [mm]: 250 - Throat depth [mm]: 350 - Transport dimensions: 2000mm x 1750mm x 2850mm (l x w x h) - Transport weight [kg]: 6000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum