Used Stahl 250 Kg for sale (68,560)

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: Hjdpfox A U Ncjx Al Sjl The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: new, Year of construction: 2026, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 800-900 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site Hsdpeng Exasfx Al Sjl - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 600-700 kg (depending on version) Ergonomic operation via safety foot switch Hedpfxjndn Ags Al Sel OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, PROFILE BENDING ATTACHMENT PB20 The PB20 profile bending attachment is the optimal supplement for tube bending on the 3000 and 6000 models. The device can be easily and quickly mounted on the bending shaft without the use of tools. The workpiece is clamped onto the turntable with the clamping device and pulled around the bending tool. With this system, leg lengths to be bent can be accurately measured in conjunction with a length stop and can be bent with repeatable accuracy. TECHNICAL DATA: Hedpfx Aonh R Ekjl Ssl - Bending capacity steel 37: 100 x 10 mm, Ø 20 mm. - Many standard tools available - Special tools possible - Sharp-edged tools with bending radius R2 or 5 mm - round tools R 10 to 25 mm for bends max. 260° optional OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, the mobile bending machine with great performance: The compact, mobile design enables precise and repeatable bending stationary and directly at the installation site up to a tube diameter of 35 mm, CU 42 mm. A powerful three-phase motor and a precision gearbox provide powerful drive. The motor speed is automatically adjusted, resulting in increased return speed and shorter cycle times. Optimum bending accuracy and very high repeatability are achieved by position detection directly on the bending axis. The bending angle is easily and quickly set to 0.5° using pushbuttons. The large LCD display clearly shows the angles. The storage of up to three bending angles enables the rational bending of tubes with different bending results. For transport, the compact unit with accessories can be neatly and safely stored in sturdy transport cases. The "upright tube and rotating tool" principle ensures low space requirements during bending. Sliding shoes are used for thin-walled tubes to enable crease-free bending and to bend bends with the slightest deformations from, for example, stainless steel and copper tubes. Hjdpfxsnfvx Ns Al Sol With the PB20 profile bending attachment, flat, square and round iron can be bent without problems. POSSIBLE APPLICATIONS: - Hydraulic piping - Sample construction - Sanitary and heating construction - Technical data: - Bending capacity Ø 6 to 35 mm, CU Ø 42 mm depending on material. - Bending radius min/max: 36 mm/150 mm - Precise digital bending angle adjustment 0.5°. - Maximum 180º bending result; for special applications Endless operation possible - Hexagonal shaft 40 mm for quick tool change - Safety foot switch with emergency stop function - Alternating current 230 V connection - Weight 29 kg - Frequency converter and three-phase motor - 3 bending angles storable OPTIONAL ACCESSORIES: - Slide shoe holder - double roller holder - Profile bender PB20 - for bending flat and square bars up to max. 80 x 8 mm, round bars up to max. 20 mm - tripod base - machine case - tool case - Small bending device KBV - Special tool according to specification OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, machine/vehicle number: 1018, THE POWERFUL BENDING MACHINE FOR EXTREME USE: The compact bending machine enables precise and repeatable bending up to an outer diameter of 100 mm stationary and directly at the assembly site. Transport is possible with lift trucks or the optional rollers. A powerful three-phase motor and a precision gearbox provide a powerful drive. The machine convinces with its compact and slim design as well as the very free bending range. Optimum bending accuracy is achieved by position detection directly on the bending axis. The bending angle is set easily and quickly via a convenient and menu-driven user interface in 14 languages with touchscreen control, which guarantees even more intuitive operation. For more complex bending tasks, 100 bending programs can be stored, with an angle sequence of max. 8 bends per geometry. The multifunction control allows variable adjustment of the bending speed for forward and backward travel, and a parameterizable overbending function is provided to compensate for material springback.With the help of the four material characteristics, the material is automatically overbent to the required bending angle, thus realizing an exact bending result. The principle of "stationary tube and rotating tool" ensures low space requirements during bending. Sliding shoes are used for thin-walled tubes to achieve a wrinkle-free bending result and to bend bends with minimal deformations from e.g. stainless steel and copper tubes. With the profile bending attachment PB20 flat, square and round bars can be bent without any problems. Extremely small bending radii are made possible with the KBV small bending attachment. POSSIBLE AREAS OF APPLICATION: - Plant engineering - Hydraulic piping - Meander bending - prototyping - Sanitary and heating engineering - shipbuilding TECHNICAL DATA 10000: Bending capacity: up to 100 x 5 mm, 55 mm solid material three-phase current 400 V - Bending radius up to 500 mm - Multifunctional machine control Bending angle adjustment (0,1°) - Maximum bending angle 240 - Safety foot switch with emergency stop - Weight 600 kg OPTIONAL ACCESSORIES: - Adapter system for tools from model series 3000/6000 Hedpfx Alendk N Aj Sol with bending radius from 45 mm, incl. hexagonal shaft 40 mm - Profile bender PB20 - for bending flat and square bars up to max. 100 x 10 mm, round bars up to max. 20 mm - Small bending device KBV - Special tools according to specification - Software adaptations for special tasks OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, THE PRACTICAL HAND BENDING DEVICE: The compact, mobile design allows precise and repeatable bending in the vice. Drive is provided by a screw-in handle. A lockable adjusting ring ensures repeatable bending. The exchange of the plug-in tools is conceivably simple. The principle of "stationary tube and rotating tool" allows bending with the smallest possible footprint. For thin-walled tubes, sliding shoes are used for crease-free bending in order to produce bends with the least possible deformation from, for example, stainless steel and copper tubes. The optional version with a hexagonal mount allows the drive force of the 3000 and 6000 bending systems to be used in addition to the vise. For this purpose, the KBV is simply placed on the bending shaft of the machine. POSSIBLE APPLICATIONS: - Hydraulic piping - prototype construction - Sanitary and heating construction TECHNICAL DATA: - Bending capacity Ø 6 to 18 mm - Manual bending angle limitation - Maximum 180º bending result OPTIONAL ACCESSORIES: - KBV with hexagonal fixture for bending on model 3000 or 6000 - Machine case - Length stop OUR SERVICE FOR YOU ON SITE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site Hodpfx Aljng Amks Sel - Consultation and handling as leasing/financing purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, THE PRECISION 3-ROLL BENDING MACHINE When developing the compact and mobile horizontal bending machine, the focus was clearly set on the production of dimensionally accurate coils such as handrails for spiral staircases. This is the supreme discipline, since two mutually influencing variables (radius and pitch) must be combined in a bend to form a dimensionally accurate geometry. The interaction of tube calculation on the PC, implementation on the bending machine, and control via the measuring equipment with final correction of the bending values ensure accurate bending. By simple and few inputs into the PC tube calculation program, the local printer provides a printout and supports the calculation of all necessary bending and correction data to operate the machine. A new powerful drive concept allows infinitely variable adjustment of the bending speed, requiring only a 230 V (AC) connection. Hardened steel tools as well as hard plastic tools that are gentle on the surface are available for selection. To ensure optimum feed even with tight bending radii, all three bending shafts are driven. The drive concept also proves its worth in tough daily use on the flat, when bending tubes and profiles. Customers of the 4800, 5000 and 6000 bending system have the option of purchasing the roller bending unit without the drive. The roller bending unit with the designation RB43, can be adapted to the bending systems 4800, 5000 and 6000 via the bending shaft. In this case, the machines act as a drive unit. POSSIBLE APPLICATIONS: - Handrails/bottom rails for spiral staircases - Large tubular profile bends - General metal construction TECHNICAL DATA: - Bending capacity Ø 10 to 60 mm - bending radius min: 300 mm at Ø 42,4 mm - Bending direction right and left - Digital bending adjustment for radius and pitch - Safety foot switch with emergency stop function - Maintenance-free robust three-phase motor - Construction site suitable 230 V connection - Weight 280 kg OPTIONAL ACCESSORIES: - Support roller - for stabilization - Lifting roller - to produce controlled slope - MGR - measuring device to determine the correct radius - MGV - measuring device to determine the correct slope based on torsion - MPW - PC calculation program to determine the correct bending values - RB4303 - universal bending tool for profiles up to 60 mm height - Tools for special profiles Hjdpong A R Sjfx Al Sel OUR SERVICE FOR YOU ON SITE: - Welcome to the test production in our house in the demo room - Consultation-information meeting at your site - Consultation and handling as leasing/financing purchase via - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, THE ECONOMICAL MANDREL BENDING MACHINE FOR TIGHT BENDING RADII. For tube dimensions from 20 - 90 mm, this bending system offers solutions for complex geometries with standard radii of 2xD. Depending on material quality and wall thickness ratio, radii of 1.5xD can also be realized suitable for series production. With a tool height of 120 mm, there are also sufficient options for special profiles. The extremely precise and powerful electric drive of the bending axis as well as the stable and rigid construction of the mandrel carrier and the bending arm also contribute to the desired bending result. The plug-in bending tools allow a quick changeover to other tube dimensions. The clamping pressure for the tube clamping can be optimally adjusted. The PLC control (can be expanded as required via USB stick) with data memory and the latest X2X interface can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for a maximum of 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The control system has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. Also available with pneumatic rotation stop or with gear-assisted length and twist positioning. POSSIBLE AREAS OF APPLICATION: - Plant engineering, e.g. chemistry - hydraulic piping - metal construction- prototype construction- pipeline construction TECHNICAL DATA: Bending capacity 7000: Ø 20 to 70 x 5 mmbending capacity 9000: Ø 20 to 90 x 5 mm depending on the material- bending radius min/max: 40 mm/250 mm- Bending radii min: 1.5 x Ø (standard 2 x Ø ) - Multifunction machine control Bending angle adjustment (0,1°) - Mandrel support lengths 3000/4500/6000 mm - Maximum 180º bending result - Weight 1600-3200 kg (depending on version) - Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: - Automatic mandrel lubrication (minimum quantity) - Pneumatic or hydraulic quick chuck - Larger bending radius up to 300 mm - Positioning of the length and twist via automatic brake function or via manual stops by foot switch Hjdpenh R Suefx Al Sjl - Semi-automatic positioning of the length and twist via servo motors - Automatic tool retraction - Pipe calculation software - 10 inch touch screen with integrated tube calculation - Data transfer via cable (LAN), via radio (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing purchase via - the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, machine/vehicle number: 1018, THE MANDREL BENDER WITH MANUEL CLAMPING: This mandrel bending machine with manual eccentric quick clamping for tube fixing enables rational bending. The compact drive unit with the detachable mandrel carrier offers advantages when used at the assembly site. Optimum bending accuracy is achieved by position detection directly on the bending axis. The bending angle is set easily and quickly via a convenient touchscreen control with menu-driven user interface. The comfort control allows two speeds as well as a parameterizable overbending function to compensate for material springback. The bending sequence is significantly shortened by automatic "free travel" at the end of the sheet. For more complex bending tasks, bending programs can be stored with a maximum angle sequence of 50 bends per geometry. An almost unlimited number of programs can be stored on the control or a USB stick, as well as 200 materials. The plug-in bending tools allow rapid conversion to other tube sizes. For difficult geometries, the bending direction of the machine can be changed to right or left bending as standard. The open bending unit allows, for example, the bending of railing frames with only one weld seam. The optional calculation software on the PC determines the cut length for the entire geometry as well as the travel distance, twisting angle and bending angle for each bend. The mandrel retraction is programmable and can be retracted automatically ahead of time when a bending angle is reached. POSSIBLE APPLICATIONS: - Plant engineering, e.g. chemical industry - hydraulic piping - prototyping - Pipeline construction TECHNICAL DATA: - Bending capacity Ø 6 to 50 mm - bending radius min/max: 10 mm/140 mm - Bending radii 2 x D - multifunction machine control bending angle adjustment (0,1°) - mandrel beam lengths 1500/3000/4500/ 6000 mm (special version also longer) - Maximum 180º bending result - Weight 300-500 kg (depending on version) Hjdpfjnfvy Uex Al Sjl Optional accessories: - Automatic mandrel lubrication (minimum quantity) - Digital displacement measurement for length and twist (resolution 0.1 OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, machine/vehicle number: 1018, THE POWERFUL BENDING MACHINE FOR WORKSHOP AND ASSEMBLY. The compact and mobile bending machine enables precise and repeatable bending up to an outer diameter of 60 mm stationary and directly at the assembly site. A powerful three-phase motor and a precision gearbox provide a powerful drive. Optimum bending accuracy is achieved by position detection directly on the bending axis. The bending angle is set quickly and easily via a convenient, menu-driven user interface with touchscreen control, which guarantees even more intuitive operation. For more complex bending tasks, 100 bending programs can be stored, with an angle sequence of max. 8 bends per geometry. The multifunction control allows variable adjustment of the bending speed for forward and backward travel, and a parameterizable overbending function is provided to compensate for material springback. Hsdpeng Ax Sefx Al Sjl With the aid of the four material characteristics, the material is automatically overbent to the required bending angle, thus realizing an exact bending result. The "stationary tube and rotating tool" principle ensures low space requirements during bending. Sliding shoes are used for thin-walled tubes to achieve a wrinkle-free bending result and to bend bends with minimal deformations from e.g. stainless steel and copper tubes. With the PB20 profile bending attachment, flat, square and round bars can be bent without any problems.Extremely small bending radii are made possible with the KBV small bending attachment. POSSIBLE AREAS OF APPLICATION: - Plant engineering- Hydraulic piping - Meander bending- prototyping- Sanitary and heating construction TECHNICAL DATA: Bending capacity 6000S: Ø 6 to 50 x 4 mm alternating current 230 V Bending capacity 6000D: Ø 6 to 60 x 4 mm Bending capacity 6000DS: Ø 6 to 60 x 5 mm three-phase current 400 V Bending capacity 6000D: Ø 6 to 60 x 4 mm three-phase 400 V - Bending radius min/max: 36 mm/280 mm - Optional large bending radii up to 500 mm - Multifunction machine control Bending angle adjustment (0.1°) - Maximum bending angle 240 - Hexagonal shaft 40 mm for quick tool change - Safety foot switch with emergency stop - Weight 110 kg OPTIONAL ACCESSORIES: - Profile bender PB20 - for bending flat and square iron up to max. 100 x 10 mm, round iron up to max. 20 mm - Roller bender RB43 - The RB43 is placed on the 6-edge shaft of the bending axis. By switching over to endless bending, the bending system acts as a drive unit. - Small bending device KBV - Special tool according to specification OUR SERVICE FOR YOU ON SITE: - Welcome to the test production in our house in the demo room - Consultation-information meeting at your site - Consultation and handling as leasing/financing purchase via - Service contracts, maintenance at your site

Condition: used, - Underfloor suction feeder - 2 folding pockets - Counter Hjdpsy Iaczofx Al Sjl - Electric belt delivery Technical data according to the manufacturer: Min. sheet size: 70 x 120 mm Max. sheet size: 320 x 450 mm Paper weight: 40 – 250 g/sqm _____ The depicted second folding unit (2 folding pockets) is not operational; it must be thoroughly overhauled before commissioning!!!

Condition: used, Year of construction: 2002, 4 buckles Knife / pocket / knife Hodpfxjx H Sv Re Al Sol with SB-66 MP.D press stack delivery (with marking device) Very good condition Available at short notice

Condition: used, Year of construction: 2002, Roundpilefeeder RD.2-78 1 station TD-78 6 pockets 2. station TD-66 4 pockets Delivery SBP-M 86.D Glueing device Hodpfsud U D Isx Al Sjl Rear -and front-mounted slitter shafts Gate-fold unit Available: at short term

Condition: used, Year of construction: 1988, Stahl Folder T 49-4 4 buckles 1 blade Hodpfx Aljruu Hzo Sel

Condition: good (used), Collet sleeves, collet, tool holder, tool holder, milling chuck, milling tool, collets -Number of clamping sleeves: 29 pieces -Various sizes: Ø 9-35 mm -6,10,13,14,20,20,20,20,22,24,24,24,26,26,27,28,30,30,30,32,33,3 3,35,35,35,35,35,35 Hjdpfx Ajb A Swkjl Ssl -Cone: 44 to 55 mm -Shaft: Ø 42 mm -Sale: only as a package -Weight: 16 kg

Condition: excellent (used), Forklift tipping container, tipping container, tipping skip, forklift skip, waste tipping container, scrap tipping container -Condition: NEW -Contents: 0.8 m³ -Steel sheet: 3 mm -Mounting: for forklift tines -Max. tine width: 150 mm -with tilting mechanism -Storage: stackable -Corrosion protection: Powder-coated -Dimensions: 1750/750/H870 mm -Quantity: 6 pieces available -Price: per piece -Weight: 180 kg Hsdpfx Aleb A Hupj Sol

Condition: reconditioned (used), Year of construction: 2021, portalkran 2x35 ton 25 or 28 meter spann longer possible Hsdpfxjggggpo Al Sel

Condition: excellent (used), DEMAG / ABUS / STAHL / LIFTKET - travelling trolleys / push trolleys / running wheels / rollers - 24 pieces: 1. Demag Type: U/EU 22 DC - 2200 kg (2 pcs). 2. Stahl - 1000 kg. 3. Abus Type: EF14 - 1400 kg. 4. Liftket Type: HFW500 - 500 kg. 5. Trolley, 2 pcs. 6. Trolley - 5000 kg. 7. Demag - 1350 kg. 8. Abus - 580 kg. 9. Demag Type: EU-RU 5 PK - 1100 kg. 10. Demag Type: EU/RU 22 DK - 2600 kg. Hedpfxey D Tvye Al Sel 11. Trolley, 3 pcs - 1100 kg. 12. Hadef roller - 2000 kg. 13. Running wheels / rollers - 7 pcs.

Condition: like new (used), Steel constructions – 2.50 PLN per kg Hodpfjy H Eu Tsx Al Ssl

Condition: used, We are offering a used drive-through floor scale for sale. TECHNICAL DATA Manufacturer: Kern Model: NFB 600K200LM Weighing range: 600 kg Hodpfxjy Ep The Al Sjl with evaluation unit Weighing surface dimensions: 1,200 x 1,200 mm Platform dimensions: 1,800 x 1,400 mm Readability: 0.2 kg Weight: 235 kg Condition: used PRICES Price: €695.00 net per unit Price: €825.05 gross per unit incl. VAT YOUR CONTACT PERSONS AT OUR COMPANY: Tanja Henkelmann Rainer Nürenberg Oliver Kopp PAYMENT TERMS Payment conditions are to be agreed in case of order. The price is per unit/net price or as stated in the description (plus VAT). Of course, you will receive an invoice showing VAT separately. ABOUT US DLK, based in Nordhorn, trades in new and used products in the fields of warehouse logistics, conveyor technology, steel mezzanine floors, textile warehouses, as well as machinery for commerce, industry, and trades. We continuously offer attractive used equipment from various manufacturers/brands at competitive conditions. If you have any questions, please feel free to contact us. Four wins – The success building blocks of DLK – Warehouse Technology | Levelmaker® | Logistics | Solutions.

Condition: refurbished (used), Used K + G Wetter WW 130mm angle grinder is a reliable and durable device designed for grinding both fresh and slightly frozen products. Perfect for small and medium-sized production plants. All made of stainless steel, which guarantees the highest hygiene at work and ease of maintenance. It has two speeds 11/19kW Plate perforations: 2, 3, 5, 8, 10, 12 mm Manufacturer: K+G Wetter Hsdpfx Ask Tzwljl Sel Model: WW 130 Height: 1950 mm Width: 1400 mm Length: 1500 mm Weight: 800 kg Capacity: 185l l Electric power supply: 400V 50Hz 3N Total power: 11/19kW Throat Diameter: 130 mm

Condition: excellent (used), functionality: fully functional, Year of construction: 1989, machine/vehicle number: GP3180, Technical data: 1x Demag KBK 2 pillar slewing crane, rated load 500KG Rated load at full outreach: 500KG Height: approx. 3.5 + 0.3m column extension Underside of jib: approx. 3.3m Outreach: 3m Hook height: approx. 2.9m Hodpfsy D D Adox Al Sol Total weight: approx. 600KG With Liftket 500KG chain hoist, year 2012 Incl. bolts, cable trolley, trolley drive, end cap, etc. Slewing range 300°, connection 400V 16A Crane is dismantled and immediately available Item location: 75053 Gondelsheim More cranes available, capacities 80–5000Kg, please enquire See photos Shipping by forwarding agent or collection by appointment only

Condition: excellent (used), Year of construction: 1985, machine/vehicle number: 27830/85, (PACKAGE INSERT FOR DRUGS) Paper size range (cm) : max. 36x52 A3+ // min. 8x10 Pockets: 4 Knives: 1 Station: TS36/4J Hodpfx Alorigrpo Ssl Feeder: FT36J Folding unit: KB36

Condition: used, empty load weight: 5,450 kg, maximum load weight: 12,550 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 07/2012, next inspection (TÜV): 04/2026, loading space length: 7,700 mm, loading space width: 2,500 mm, loading space height: 2,300 mm, loading space volume: 44 m³, total length: 7,700 mm, suspension: air, tire size: 385/65 22,5, tire condition: 30 %, color: blue, Year of construction: 2012, front tire size: 385/65 22,5, rear tire size: 385/65 22,5, driver cabin: day cab, Equipment: ABS, tail-lift, truck registration, Reference Number for Inquiries: 408211 Krone, S 24 * Year of Manufacture: 2012 * ABS (Anti-Lock Braking System) * EBS (Electronic Braking System) Hedpjynvzrofx Al Sjl * Tail Lift * Alloy Wheels * Air Suspension * Tandem Trailer * Load Securing Certificate to DIN EN 12642 Code XL * VDI 2700 EN 12195 Compliance * Duo-matic Air Coupling * 15-Pin Connector Plug * Lifting and Lowering Device * Rear Support Legs * Inspections: Main/Emission Inspection valid until 04.2026 * Suspension: Air * Gross Vehicle Weight: 18,000 kg * Unladen Weight: 5,450 kg * Payload: 12,550 kg * Permissible Gross Weight: 18,000 kg * Axle Manufacturer: BPW * Tyre Condition 1st Axle: 30% -- 30% - Tyre Size: 385/65 R22.5 * Tyre Condition 2nd Axle: 30% -- 40% - Tyre Size: 385/65 R22.5 * Tyre Sizes: 385/65 R22.5 * Internal Dimensions: L = 7700 mm, W = 2500 mm, H = 2300 mm * Internal Volume*: 44 m³ * Pallet Spaces: 19 * Trailer Brand: Krone * Body: Ewers Swing-Wall Semi-Trailer * Tail Lift: BÄR BC 2500 – Capacity 2,500 kg Disclaimer: Subject to change, prior sale, and errors excepted. More photos and videos can be found on our website. Our comprehensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Fast, straightforward financing * Application for all (export) documents * Procurement of export / customs license plates * Vehicle reconditioning: new tarpaulins, lettering, painting, etc. * Professional loading & load securing * TÜV inspections, registration service * Transport of commercial vehicles Please contact our trained professionals for further assistance – we are happy to advise you.