Used Autefa Cross-Layer for sale (5,046)

Condition: ready for operation (used), Year of construction: 1992, A dismantled Autefa compensating stacker is available. Working width: 3000mm, working speed: 60m/min. On-site inspection is possible. Nedpfx Aswwvw Tsc Ujlf

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Nljdpfx Ajzp H R Eoc Uof Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: used, Year of construction: 1986, functionality: fully functional, AUTEFA Bale Press LIFT BOX - semi-automatic bale press - 2-chamber system - pre-press - final press - automatic TITAN strapping machine - control unit renewed in 2015 Nlodpfx Acsytb Sge Uef - hydraulics completely renewed in 2018 - condenser new in 2012 - fork bale removal trolley - transport segments (roller conveyors) - turntable - roller conveyor scale - roller conveyor lift table - packaging material - bale size WxLxH 1250x750x1100 mm - bale weight approx. 330 kg - daily throughput 25-30 t System available 2x (price per unit) Please note that disassembly, packing, and shipping/collection must be carried out by the buyer.

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm Nedpfefv Hphjx Ac Uelf angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Year of construction: 2009, condition: good (used), Technical Data: Format: min 145 x 200 mm; max 300 x 430 mm Stack height: max 50-300 mm Stack weight: max 18 kg Nodpfx Acsnab Uds Ujlf Speed for strapped / film wrapped bundles: max 36 bundles/min Speed for loose bundles (only with Blocking Unit!): max 24 bundles/min Palletizing height (incl. pallet): max 1600 mm Description: Palletizing of strapped, film wrapped or loose (product permitting!!) bundles. With blocking unit for stable bundles. Infeed with turning device for variable rows which are combined to a layer. Each finished layer is then placed onto the pallet. Includes pallet conveying and empty pallet terminal. Equipment: Palletizer: · Simple palletizer (one line) · Product orientation at infeed palletizer (standard): längs Blocking unit: · Model: VB 95 · Serial Number: 446 · Infeed with flying cross (turning device) for bundles · Right hand palletizer (palletizing to the right of the infeed) Slip sheet dispenser: Empty pallet dispenser: · Model: PT · Serial Number: 246 Pallet conveying: · Pallet width (max): 1.000 mm · 2 additional buffer positions for full pallets: · Configuration of pallet conveying gerade All technical data is for information purposes only! Although the technical information is mostly taken from manufacturers documents, no guarantee can be given for correctness due to e.g. undocumented changes of the equipment. By no means are these values intended to be binding or part of the contract.

Condition: good (used), Description/configuration: Palletizing of strapped, film wrapped or loose (product permitting!!) bundles. With blocking unit for stable bundles. Infeed with turning device for variable rows which are combined to a layer. Each finished layer is then placed onto the pallet. Includes pallet conveying and empty pallet terminal. Layout available min format product: 145 mm x 200 mm max format product: 300 mm x 430 mm max stack height: 50-300 mm max stack weight: 18 kg max speed for strapped / film wrapped bundles: up to 36 bundles/min max speed for loose bundles (only with Blocking Unit!): up to 24 bundles/min max palletizing height (incl. pallet): ~1600 mm Simple palletizer (one line) Low bundle infeed Nedpshrmlgsfx Ac Uolf Infeed height: ~870 mm Product orientation at infeed palletizer (standard): Spine to the side Blocking unit in front of infeed (model): VB 95 Reference-# blocking unit: 26180X.30 Serial Number blocking unit: 136 Infeed with flying cross (turning device) for bundles Infeed with emergency delivery for bundles (straight out) Left hand palletizer (palletizing to the left of the infeed) With slip sheet dispenser Empty pallet dispenser (model): PT 80 Reference-# empty pallet dispenser (pallet terminal): 26180X.40 Serial number empty pallet dispenser (pallet terminal): 78 Includes pallet conveying, reference-no: 26180X.50 Conveying for a pallet width of 800 & 1000 mm Pallet conveying elevated Height of pallet conveying: ~300 mm Configuration of pallet conveying: straight Optional equipment: additional infeed conveyors (as shown on layout) Over all length equipment: ~5600 mm Over all width equipment: ~5000 mm Over all height equipment: ~3400 mm Input Power: ~7 KVA, 50/60 Hz, 3 ~ Voltage: 400 V 3Ph N, PE, 50 Hz Air requirement: 0,35 Nm3/min 6 bar Weight: ~4000 kg Equipment at warehouse Helmstedt, airports: Hannover (~1 hr), Berlin (~2 hrs) Condition: as is

Condition: good (used), Description/configuration: Palletizing of strapped, film wrapped or loose (product permitting!!) bundles. With blocking unit for stable bundles. Infeed with turning device for variable rows which are combined to a layer. Each finished layer is then placed onto the pallet. Includes pallet conveying and empty pallet terminal. Layout available min format product: 145 mm x 200 mm max format product: 300 mm x 430 mm max stack height: 50-300 mm max stack weight: 18 kg Nlsdpfx Ajhrmlcec Uef max speed for strapped / film wrapped bundles: up to 36 bundles/min max speed for loose bundles (only with Blocking Unit!): up to 24 bundles/min max palletizing height (incl. pallet): ~1600 mm Simple palletizer (one line) Low bundle infeed Infeed height: ~870 mm Product orientation at infeed palletizer (standard): Spine to the side / längs Blocking unit in front of infeed (model): VB 95 Reference-# blocking unit: 26150X.30 Serial Number blocking unit: 75 Infeed with flying cross (turning device) for bundles Serial Number turning device: DK 5 Infeed with emergency delivery for bundles (straight out) Right hand palletizer (palletizing to the right of the infeed) With slip sheet dispenser Empty pallet dispenser (model): PT 80 Reference-# empty pallet dispenser (pallet terminal): 26150X.40 Serial number empty pallet dispenser (pallet terminal): 53 Includes pallet conveying, reference-no: 26150X.50 Conveying for a pallet width of 800 mm Pallet conveying mounted on floor Configuration of pallet conveying: straight Optional equipment: additional infeed conveyors (as shown on layout) Over all length equipment: ~5600 mm Over all width equipment: ~5000 mm Over all height equipment: ~3400 mm Input Power: ~7 KVA, 50/60 Hz, 3 ~ Voltage: 400 V 3Ph N, PE, 50 Hz Air requirement: 0,35 Nm3/min 6 bar Weight: ~4000 kg Equipment at warehouse Helmstedt, airports: Hannover (~1 hr), Berlin (~2 hrs) Condition: as is

Condition: good (used), Description/configuration: Palletizing of strapped, film wrapped or loose (product permitting!!) bundles. Infeed with blocking unit & turning device. The palletizer builds single rows of bundles which are combined to a layer. Each finished layer is then placed onto the pallet. Includes pallet conveying and empty pallet terminal. Layout available min format product: 145 mm x 200 mm max format product: 300 mm x 430 mm max stack height: 50-300 mm max stack weight: 18 kg max speed for strapped / film wrapped bundles: up to 36 bundles/min max speed for loose bundles (only with Blocking Unit!): up to 24 bundles/min max palletizing height (incl. pallet): ~1600 mm Simple palletizer (one line) Low infeed Infeed height: ~870 mm Product orientation at infeed palletizer (standard): Spine to the side Blocking unit in front of infeed (model): VB 95 Reference-# blocking unit: 26001X.30 Serial Number blocking unit: 152 Infeed with flying cross (turning device) for bundles Infeed with emergency delivery for bundles (straight out) Right hand palletizer (palletizing to the right of the infeed) With Slip sheet dispenser Empty pallet dispenser (model): PT Reference-# empty pallet dispenser (pallet terminal): 26001X.40 Includes pallet conveying, reference-no: 26001X.50 Conveying for a pallet width of 800 & 1000 mm Pallet conveying mounted on floor Configuration of pallet conveying: straight Optional equipment: additional infeed conveyors (as shown on layout) Over all length equipment: ~5600 mm Over all width equipment: ~5000 mm Over all height equipment: ~3400 mm Input Power: ~7 KVA, 50/60 Hz, 3 ~ Voltage: 400 V 3Ph N, PE, 50 Hz Air requirement: 0,35 Nm3/min 6 bar Weight: ~4000 kg Color: Blue Equipment at warehouse Helmstedt, airports: Hannover (~1 hr), Berlin (~2 hrs) Njdpfohrigqox Ac Uolf Condition: as is Machine available: upon request

Condition: good (used), Description/configuration: Palletizing of strapped, film wrapped or loose (product permitting!!) bundles. With blocking unit for stable bundles. Infeed with turning device for variable rows which are combined to a layer. Each finished layer is then placed onto the pallet. Includes pallet conveying and empty pallet terminal. Layout available min format product: 145 mm x 200 mm max format product: 300 mm x 430 mm max stack height: 50-300 mm max stack weight: 18 kg max speed for strapped / film wrapped bundles: up to 36 bundles/min max speed for loose bundles (only with Blocking Unit!): up to 24 bundles/min max palletizing height (incl. pallet): ~1600 mm Simple palletizer (one line) Low bundle infeed Infeed height: ~870 mm Product orientation at infeed palletizer (standard): Spine to the side Blocking unit in front of infeed (model): VB 95 Reference-# blocking unit: 26027.30 Serial Number blocking unit: 147 Infeed with flying cross (turning device) for bundles Infeed with emergency delivery for bundles (straight out) Left hand palletizer (palletizing to the left of the infeed) With slip sheet dispenser Empty pallet dispenser (model): PT Reference-# empty pallet dispenser (pallet terminal): 26027.40 Serial number empty pallet dispenser (pallet terminal): 132 Includes pallet conveying, reference-no: 26027.50 Conveying for a pallet width of 800 & 1000 mm Pallet conveying elevated Height of pallet conveying: ~300 mm Configuration of pallet conveying: straight Optional equipment: additional infeed conveyors (as shown on layout) Over all length equipment: ~5600 mm Over all width equipment: ~5000 mm Over all height equipment: ~3400 mm Input Power: ~7 KVA, 50/60 Hz, 3 ~ Nlodpfjhrmk Rox Ac Ujf Voltage: 400 V 3Ph N, PE, 50 Hz Air requirement: 0,35 Nm3/min 6 bar Weight: ~4000 kg Equipment at warehouse Helmstedt, airports: Hannover (~1 hr), Berlin (~2 hrs) Condition: as is Machine available: upon request

Condition: good (used), Description/configuration: Palletizing of strapped, film wrapped or loose (product permitting!!) bundles. With blocking unit for stable bundles. Infeed with turning device for variable rows which are combined to a layer. Each finished layer is then placed onto the pallet. Includes pallet conveying and empty pallet terminal. Layout available Nlsdpfxehrmk Ue Ac Usf min format product: 145 mm x 200 mm max format product: 300 mm x 430 mm max stack height: 50-300 mm max stack weight: 18 kg max speed for strapped / film wrapped bundles: up to 36 bundles/min max speed for loose bundles (only with Blocking Unit!): up to 24 bundles/min max palletizing height (incl. pallet): ~1600 mm Simple palletizer (one line) Low bundle infeed Infeed height: ~870 mm Product orientation at infeed palletizer (standard): straight Blocking unit in front of infeed (model): VB 95 Reference-# blocking unit: 26046.30 Serial Number blocking unit: 147 Infeed with flying cross (turning device) for bundles Infeed with emergency delivery for bundles (straight out) Right hand palletizer (palletizing to the right of the infeed) With slip sheet dispenser Empty pallet dispenser (model): PT Reference-# empty pallet dispenser (pallet terminal): 26046.40 Includes pallet conveying, reference-no: 26046.50 Conveying for a pallet width of 800 & 1000 mm Pallet conveying elevated Height of pallet conveying: ~300 mm Configuration of pallet conveying: straight Optional equipment: additional infeed conveyors (as shown on layout) Over all length equipment: ~5600 mm Over all width equipment: ~5000 mm Over all height equipment: ~3400 mm Input Power: ~7 KVA, 50/60 Hz, 3 ~ Voltage: 400 V 3Ph N, PE, 50 Hz Air requirement: 0,35 Nm3/min 6 bar Weight: ~4000 kg Equipment at warehouse Helmstedt, airports: Hannover (~1 hr), Berlin (~2 hrs) Condition: as is Machine available: upon request

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, For sale is an R. Beck multi-level gluing press in a robust industrial design. This machine is ideally suited for efficient carcass, frame, and panel construction, as well as for a wide range of gluing applications in carpentry and furniture making. The 5 independently operated press levels allow for the simultaneous processing of multiple workpieces, resulting in high productivity. Technical data: Nodpfozm Slvsx Ac Uolf Manufacturer: R. Beck Maschinenbau Year of manufacture: 1997 Usable length: 2,000 mm 5 press levels Operating pressure: 6 bar CE version Machine no.: 270 Equipment: Pneumatic multi-level gluing press 5 press levels, individually selectable Pneumatic pressing Multiple clamping cylinders per level Even pressure distribution Control panel with individual control of the press levels Mobile base frame Robust industrial design Ideal for carcass, frame, and panel gluing Application areas: Furniture manufacturing Carpentry Joinery Carcass gluing Frame gluing Panel gluing Series production Condition: The machine is in used, well-maintained condition with the usual signs of wear and tear consistent with its age. Thanks to its robust construction, it is ideally suited for professional use in crafts and industry. Inspection and test run are possible at any time by appointment. Transport is possible for an additional charge! The machine will be inspected before sale. For used machines manufactured in 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sale, and changes are subject to change. All information is without guarantee.

Condition: repair required (used), functionality: limited functionality, machine/vehicle number: 2003645, Year of construction: 2013, operating hours: 11,961 h, load capacity: 9,000 kg, lifting height: 4,500 mm, free lift: 580 mm, load center: 1,050 mm, fuel type: electric, mast type: mono, motor manufacturer: Hubtex, battery manufacturer: Heppecke, battery model: Nass-Batterie Aquamatic EUW, battery capacity: 465 Ah, battery voltage: 48 V, battery weight: 731 kg, fork carriage width: 200 mm, fork length: 2,100 mm, ground clearance: 75 mm, turning radius (outer): 2,650 mm, front tire type: polyurethane tires (non-marking), rear tire type: polyurethane tires (non-marking), rear tire size: 343X114, empty load weight: 4,335 kg, total length: 3,638 mm, total width: 1,650 mm, color: orange, Equipment: CE marking, UVV, head guard, Special design: see documents – product specification + EC declaration of conformity. Drive and steering motor requires repair. Spare parts package. Nljdpfszwpp Hex Ac Uof

Condition: used, Year of construction: 2010, functionality: fully functional, machine/vehicle number: 467334, Manufacture year 2010 Machine specifications: - Push infeed, max. length 6300 mm - Automatic length measuring and chalk reader - Cutting width 40 – 420 mm - Cutting height 15 – 170 mm - Min. cross section 20 x 10 mm - Max. cross section 270 x 170 / 410 x 30 mm - Motor 13.5 kW - Total electrical load approx. 22 kW -Operating pressure approx. 8 bar - Saw blade diameter 630 mm / bore 30 mm Consisting of: 1. Cross chain infeed system 8 pc. chain transport with 3 latch rows 2. Push infeed system with liftable pusher Infeed length 6300 mm, length detecting and chalk reader 3. OptiCom Direct controller 4. Opticut cross cut saw unit S90 XL With side pusher and waste gate Nlsdsypvdijpfx Ac Ujf 5. Outfeed transport belt

Condition: used, Year of construction: 2018, N = tilting brake motor with 5 kW. Saw blade diameter 520 mm, bore 50 mm. Cutting height 200 mm. Cutting length 420 mm. Saw blade tilted to 45°: cutting height 140 mm. With machine stand and hand crank for tilt adjustment. Hydraulic feed brake for ZS 200 and ZS 200N; a coolant emulsion is used as the hydraulic medium. 5-meter long infeed roller conveyor mounted on the right: RO-ST60, 5.0 m long. Mounting side: right. Heavy-duty design, steel rollers with a diameter of 60 mm, roller spacing 200 mm, roller width 400 mm, 4 support feet, and connecting piece. 5-meter long measuring length roller conveyor mounted on the left: RLH-ST60, 5.0 m long. Mounting side: left. Length stop/roller conveyor, heavy-duty design, stop slide adjustable from the workstation via a handwheel, electronic-digital dimension display, stop slide pneumatically lockable, stop flap foldable to the rear, with steel rollers with a diameter of 60 mm, roller spacing 200 mm, roller width 400 mm, with 4 support feet and connecting piece. Overall length: 5.7 m. Location: Nattheim. Nljdjzwm Ndopfx Ac Uef

Condition: used, Year of construction: 2013, functionality: fully functional, One side scanner for sorting or optimization: Width: 30-200mm High: 13-50mm Njdjv Tlgdspfx Ac Uolf Length: 2-6m Possible to detect: Knots, wood structure, cracks, end cracks, color variations etc. Scanning speed: up to 200m/min Possible to scan different profiles

Condition: used, Year of construction: 1999, functionality: fully functional, cutting height (max.): 100 mm, cutting width (max.): 2,500 mm, saw blade diameter: 400 mm, height adjustment type: mechanical, Equipment: saw blade guard, Double-blade panel saw, Eima Type 122 Nledpfx Acjzwkrve Uef Cutting width, min/max: 210-2500 mm Cutting depth: 2500 mm Maximum blade diameter: 400 mm Cutting height: ~100 mm Motor power: 2 x 4.4 kW Electronic cutting width adjustment

Condition: new, Year of construction: 2024, operating hours: 15 h, functionality: fully functional, total height: 2,545 mm, total width: 2,700 mm, total length: 7,510 mm, type of input current: three-phase, overall weight: 8,500 kg, input voltage: 400 V, pressure: 6 bar, power: 55 kW (74.78 HP), Application area: Paper and film processing Specialty papers (e.g. package inserts, labels, lightweight printing papers) Plastic films (e.g. sensitive or scratch-prone materials) Technology / Features: Contactless sheet transport using AirStream (air conveyance) Very high format flexibility and rapid job changes High cutting and register accuracy Gentle material handling, even with very light substrates Performance data (typical): Speed: up to approx. 400 m/min Substrate weights: approx. 30–300 g/m² paper Cut lengths: approx. 400–1,060 mm (optionally larger) Strengths: Ideal for small batch sizes and frequent format changes Nedpfx Acsy Egdte Uelf High production speed with consistently good quality Reduced waste rate and excellent stack quality Compact design and easy integration into existing lines Inspection and test run possible by arrangement Assembly and disassembly can be arranged by the manufacturer Warranty provided by the manufacturer

Condition: used, Year of construction: 2005, total height: 1,750 mm, total length: 1,350 mm, total width: 1,350 mm, Colour: Grey Weight: 415 kg Optimization cross-cut saw Stromab TR 500 Nsdpfx Aewq U Dxoc Ujlf Matrix 4 4000 Year of construction 2005 Engine power 10 hp Auto push-up system Inkjet printer - Year: 2005 - Documentation available: No - CE certificate present: No - Serial number: 250143 - Main motor power [kW]: 7.5 - Max. saw width [mm]: 375 - Arbor saw blade diameter [mm]: 30 - Input table length [mm]: 4300 - Output table length [mm]: 2000 - Transport dimensions: 1350mm x 1350mm x 1750mm (l x w x h) - Transport weight [kg]: 415kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, power: 4.4 kW (5.98 HP), cutting height (max.): 6,000 mm, saw blade diameter: 500 mm, tilt adjustment saw blade: 90 °, rotational speed (max.): 2,800 rpm, On sale Pertici saw that is no more required. wo headed automatic saw for cutting aluminium profiles. Saw blade diameter: 500 mm Max cutting lenght: 6000mm Min cutting lenght: cca 330 mm Engine power: two three-phase motors, each one 2,2 kW (summary4,4 kW), 2800 rpm Head tilt: 90-45° Nedpfxeztc Dcj Ac Uolf Year of production : 2016 Price: 9300€ The machine can be seen in Rugvica, Croatia (nearby Zagreb).

Year of construction: 1990, condition: ready for operation (used), A complete nonwoven fabric production line including peripheral equipment and a complete pre-blending line is available. 1) Pre-blending line with carding opener Houget Duesberg Bosson, year of construction: 1972, working width: 1500mm, drum: 1, worker-stripper pairs: 3, doffer: 1, feed rollers: 2, total line dimensions X/Y/Z: approx. 11000mm/1800mm/3100mm, operating hours: approx. 16414h, including feed table and bale opener. 2) Filling chute Spinnbau Bremen, year of construction: 1989, machine dimensions X/Y/Z: approx. 4000mm/2600mm/6250mm. 3) Weighing conveyor with vibrating chute Protec. 4) Card Hergeth, year of construction: 1990, working width: 2500mm, feed rollers: 2, feed roller diameter: 94mm, licker-in roller diameter: 413mm/550mm, worker-stripper roller diameter: 219mm/123mm, transfer roller diameter: 550mm, main cylinder diameter: 1500mm, doffer diameter: 850mm, compaction roller diameter: 260mm, pressure roller diameter: 2500mm. 5) Crosslapper Autefa Topliner CL 4000/4002 - WebMax, year of construction: 2006, min. fineness range: 0.7dtex, fiber types: chemical/natural/regenerated/blends, max. web weight: 100g/m², max. web weight with crosslapper: 5000g/m², max. laying width: 3500mm, working width: 2500mm, max. laying speed: 130m/min, lapper lift: 100mm, machine dimensions X/Y/Z: approx. 3850mm/8800mm/2200mm. 6) Drafting unit, working width: 2500mm, machine dimensions X/Y/Z: approx. 1600mm/3650mm/1650mm. 7) Double needle loom Dilo CBF 31/HVSL 31, year of construction: 2007, max. working width: 3100mm, stroke frequency: 1375/min, needle beam stroke: 60mm, horizontal beam stroke range: 0mm-6mm, number of needles per 1m working width: approx. 15430, machine dimensions X/Y/Z: approx. 3350mm/5150mm/4500mm, weight: approx. 38000kg. 8) Web accumulator Suchy WOB 3200, storage volume: 40m³, web weight range: 50g-2000g/m², max. working speed: 40m/min, max. production speed: 20m/min, working width range: 1000mm/3000mm, roller top width: 3200mm, machine dimensions X/Y/Z: approx. 4300mm/5050mm/5300mm. 9) Slitting unit Suchy, year of construction: 2006, weight: approx. 250kg. 10) Climbing roll winder, winding roller diameter: 350mm, min. winding diameter: 3inch, max. winding diameter: 1500mm. 11) Edge trimmer Hepp-Schwamborn. 12) X-ray measuring device Protagon Q6. This is a complete and automated nonwoven fabric production line starting from fiber bales. Documentation available. An on-site inspection is possible. Expected to be available from the end of March 2026. Nledpfxsymfc Aj Ac Uof

Condition: ready for operation (used), Year of construction: 2016, functionality: fully functional, We offer for sale a high-quality WEINIG Dimter OptiCut S 50 optimizing cross-cut saw, a reliable and precise solution for automated wood cutting and defect optimization. The machine is designed for efficient processing of solid wood, ensuring high productivity, accuracy, and material optimization. Key Features & Benefits Manufacturer: WEINIG Dimter GmbH & Co. KG (Germany) Model: OptiCut S 50 Year of manufacture: 2016 Optimizing cross-cut technology for maximum yield Automatic defect detection and cutting optimization Ideal for joinery workshops, sawmills, and industrial wood processing Technical Specifications General Voltage: 400 V Frequency: 50 Hz Machine No.: 6978.14 Material Dimensions Max. workpiece length: up to approx. 6,300 mm Width: approx. 20 – 300 mm Thickness: approx. 10 – 120 mm Max. workpiece weight: approx. 60 kg Cutting Performance Minimum cutting length: approx. 10 mm High-speed cross-cut optimization for defect removal and yield maximization Machine Configuration Feeding System Infeed table approx. 6.3 m Automatic width detection (up to 290 mm) Laser photocell for defect recognition Automatic optimization and ejection of defects Basic Machine OptiCut S 50 unit Motor power: approx. 7.5 kW Side pressure device with rollers Outfeed System Outfeed table approx. 2.4 m Control System WEINIG OptiCom Pro control unit Extraction & Utilities Air consumption: approx. 150 Nl/min Extraction speed: min. 30 m/s Electrical total connection: approx. 9 kW Advantages Precise and efficient cutting with minimal waste Automated process reduces manual labor Proven WEINIG quality – durable and reliable Suitable for continuous industrial use Nlsdpfx Aezgr Nbjc Usf Additional Information Made in Germany CE certified Well-maintained industrial machine

Condition: excellent (used), Year of construction: 2022, operating hours: 5,000 h, functionality: fully functional, OptiCut S 50+ optimizing saw Nlodpfx Acozkbmde Uef - Feeding system with transverse conveyors and automatic pusher - Outfeed conveyor belt with 2 zones, including ejectors and tables, one of which is foldable - Saw motor: 7.5 kW - Boards/planks up to 5 meters long can be fed into the machine. - Maximum cutting cross-section: 270 x 100 mm Additional technical information and a video are available upon request.

Condition: used, Grecon Dimter Opticut 704 Optimizing Saw An optimizing saw for demanding applications. A continuous chain transport system with a flexible upper clamping device, from the measuring station to the saw, ensures safe transport of wood that is tapering, twisted, heavily rough after sanding, and prone to splitting. A servomotor with a planetary gearbox provides very high acceleration due to its low moment of inertia. Nedpfjzvyk Ssx Ac Uolf Waste is blown to the side in the cutting area. Thanks to its special design with an aluminum casting and a pneumatically controlled saw swing, very short cutting times are possible. The output is approximately 12,000–17,000 running meters per shift, with maximum cross-sections of the material being processed ranging from 100 × 100 mm to 30 × 250 mm.

Condition: used, Hüllhorst double miter saw in good, used condition. Nedpfx Acezpfk Rj Uslf The miter angle cannot be adjusted on this machine. Year of manufacture unknown. The double miter saw has been used reliably for many years in the production of moldings and is still connected to the power supply. The machine is being sold as part of the liquidation of our carpentry business. Collection price – delivery possible upon request. The sale is made excluding any warranty for defects. Liability for intent, gross negligence, and damages resulting from injury to life, limb, or health remains unaffected. Claims for defects that have been fraudulently concealed also remain unaffected. An inspection of the machine is possible by arrangement.

Condition: used, Year of construction: 2010, - Perfect for surface finishing - Constant working height - Q/L/Q Fine/cross-sanding machine Manufacturer: Weber Type: KSF-3-1350 Year of manufacture: 2010 Technical data - Equipped with 3 sanding belts for high-quality fine, veneer, and high-gloss sanding. - With a constant working height Machine frame - Heavy-duty steel welded construction for mounting 3 sanding units - Constant inlet height of 900 mm Nodpszuzctsfx Ac Uelf - Control and sanding belt change side on the inlet side, on the left - Stepless feed speed of 3-18 m/min, frequency-controlled. - Vacuum version of the conveyor belt / with 1 vacuum blower 5.5 kW, and a vacuum channel up to the upper edge of the machine Unit 1: Cross-belt unit - Pressure pad belt with felt and graphite for long service life - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Unit 2: CBF combination unit - One grooved rubber contact roller 0 130 mm, rubber hardness 60 Shore - One cross-running flap band with separate drive 4.0 kw - ISA segmented pressure bar system with 11 mm workpiece detection and 22 mm pressure pad width (counter-rotating) - Workpiece-controlled oscillating sanding belt blowing device Unit 3: Cross-belt unit - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Operator terminal SIEMENS" MP 377 12" Multi-Panel - Graphical user guidance via 12" color display - Program memory with 300 programs - Setting of all parameters via program WEBER i-Touch control - One rotary knob for navigating through the most important functions WEBER AWDM - Automatic thickness adjustment at the machine inlet with start switch Overthickness - Selector switch at the machine inlet with the following functions: - Automatic lifting of the contact roller and the segmented pressure bars - Feed stop ISA/ISD control - High-resolution workpiece detection in a 22 mm grid - Free loading of complex part shapes - Multiple loading with a small lateral distance - Sanding intensity individually adjustable at all edges - Sanding pressure adjustable via program ISA segmented pressure bar system (Unit 2) - Pressure pad movable in the longitudinal and transverse direction ISD segmented pressure bar system (Unit 1+3) As ISA, but additionally with - Separate adjustable pressure for the edge area (higher or lower) - Optionally only on the outer edge or outer and inner edges - Longitudinal and transverse edges or only longitudinal edges can be adjusted Workpiece blowing device - with WEBER ES system - Energy-saving, workpiece-controlled workpiece cleaning with single slider control WANDRES-Micro-Cleaning (single brush version) - Power sword brush with integrated micro-humidification of the linear brush (for optimal paint dust removal) Technical data - Working width: 1350 mm - Drive Unit 1 (frequency-controlled-Eco-Drive): 15.0 kW - Drive Unit 2 (frequency-controlled-Eco-Drive): 20.0 kW - Drive Unit 3 (frequency-controlled-Eco-Drive): 15.0 kW - Drive CBF: 3.0 kW - Drive vacuum blower: 5.5 kW - Drive feed (frequency-controlled): 3.0 kW - Drive height adjustment (frequency-controlled): 0.75 kW - Sanding belt speed (frequency-controlled): approx. 3-20 m/s - Sanding belt dimensions cross belts (W x L): 2x150x5100 mm - Sanding belt dimensions wide belt (W x L): 1370x2620 mm - Workpiece thickness (min./max.): 4-140 mm - Working height (constant): 900 mm - S