Used Bale Press With 70 Tons Of Pressing Force for sale (33,141)

Condition: ready for operation (used), Pressing force: approx. 700 kN (approx. 70 tons) Motor power: approx. 11 kW Power supply: 3 × 400 V / 50 Hz Single bale weight: up to approx. 600 kg Bale dimensions: approx. 1100 × 1100 × 1200 mm Machine dimensions: approx. 5.9 m in length, 2.5 m in width, approx. 2.6 m in height Machine weight: approx. 7 tons Cycle time: approx. 45–47 s Construction features large feed opening for cardboard possibility of automatic feeding (e.g., via conveyor) manual wire tying (4 wires) pallet lock and hydraulic doors for bale removal Advantages of this press large bales = fewer transports high pressing force Nwsdera Dddspfx Acfsh suitable for continuous operation Available production years: 2018–2020

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Nodszbxwiepfx Acfjwh Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, year of last overhaul: 2025, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Njdezbxvlopfx Acfjwh Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: refurbished (used), Year of construction: 2017, functionality: fully functional, overall weight: 120,000 kg, total height: 5,600 mm, pressing force: 1,250 t, air pressure: 6 bar, distance between side stands: 1,200 mm, distance between stands: 1,400 mm, stroke length: 500 mm, table length: 1,850 mm, table width: 1,600 mm, Straight-sided eccentric press ERFURT type PKZe 1250 Nsdpjubyrxefx Acfjwh Superb working condition, after full, professional overhaul. After - newer used. Specification: Capacity: 1250 ton force Slide stroke: 500 mm Slide adjustment: 215 mm Maximum shut height between bolster plate and slide (stroke down, adjustment up): 860 mm Bed area (width x depth): 1600x1850 Slide area (width x depth): 1300x1400 mm Opening in the bed (width x depth): 1100x1100 mm Main motor rating: 90 kW at 1478 RPM Ram adjusting motor rate: 7.5 kW at 1450 RPM Number of single strokes: 8 min-1 Cushion capacity: 200 ton force Cushion stroke: 200 mm Height above floor: 7900 mm Press weight: 130 000 kg.

Condition: new, Year of construction: 2025, pressing force: 200 t, stroke length: 800 mm, table width: 1,000 mm, table length: 1,000 mm, clearance between the columns: 1,000 mm, retraction force: 70 t, operating pressure: 250 bar, Equipment: documentation/manual, safety light barrier, CRONOSSTECH 200 / 70 TON FOUR-COLUMN HYDRAULIC DEEP DRAWING PRESS General Description The CRONOSSTECH 200 / 70 ton four-column hydraulic deep drawing press is a high-rigidity, four-column hydraulic press designed for metal forming, deep drawing, and precision pressing applications. The St52 grade welded steel frame is subjected to stress relief via vibration, ensuring high parallelism and perpendicularity tolerances are maintained over extended operation. The ram and blank holder (pot) systems are operated independently, with stroke and pressure settings precisely adjustable via touchscreen control panel. Equipped with REXROTH or PARKER hydraulic components, an IE3 class motor, and PLC-controlled structure, the system offers high efficiency and reliable operation. An automatic lubrication system and electronic filter contamination alerts minimize maintenance requirements. With its 200 / 70 ton capacity, this model provides an ideal industrial solution for medium and heavy-duty metal forming, deep drawing, and die applications. Key Advantages - Rigid four-column press frame - Independent stroke and tonnage adjustment for ram and blank holder - Full control via touchscreen panel - High precision and repeatability - Long-lasting, low-maintenance design Applications - Metal forming operations - Deep drawing applications - Die trial and production lines - Auxiliary pressing operations ⚙️ STANDARD AND TECHNICAL SPECIFICATIONS TYPE: Four-column FRAME MATERIAL: St52 – ERDEMIR grade COLUMN SHAFT DIAMETER: Ø 90 mm – 4 pcs, induction hardened and chrome plated SLIDE BEARING: Bronze Zr14 CAPACITY (RAM): 200 Ton CAPACITY (BLANK HOLDER): 70 Ton DISTANCE BETWEEN COLUMNS: 1000 × 1000 mm PARALLELISM TOLERANCE: 120 micron/meter PERPENDICULARITY TOLERANCE: 60 micron/meter STROKE (RAM): 800 mm STROKE (BLANK HOLDER): 200 mm MIN. OPENING HEIGHT: 100 mm MAX. OPENING HEIGHT: 900 mm WELDING STRESS RELIEF: By vibration WELDING PROCEDURE: WPQR & WPS with TURK-AK accreditation – EN ISO 15614-1:2017 (EN ISO 14731) MAX. WORKING PRESSURE: 250 Bar TOTAL MOTOR POWER: 22 kW – IE3 MAIN PUMP: 36 cm³ – REXROTH or PARKER MOVING TABLE FAST DESCENT: 150 mm/sec FORMING SPEED: 12 mm/sec RETURN SPEED: 170 mm/sec BLANK HOLDER FORWARD SPEED: 30 mm/sec MAIN CYLINDER BORE: Ø 320 mm – Ck45 BLANK HOLDER CYLINDER BORE: Ø 190 mm – Ck45 AUXILIARY SPEED-UP CYLINDERS: 2 units PRESS APPROX. DIMENSIONS: 4000 × 1450 × 1450 mm LOWER TABLE HEIGHT FROM FLOOR: 1300 mm MAIN CHARGE VALVE: NG 125 HYDRAULIC UNIT: REXROTH or PARKER COOLING SYSTEM: EMMEGI – CIESSE – PARKER OFF-LINE FILTRATION: REXROTH or PARKER PLC: DELTA TOUCHSCREEN PANEL: DELTA 7” Nwjdjx N Umqopfx Acfjh CONTROL COMPONENTS: SIEMENS – SCHNEIDER APPROX. WEIGHT: 14.5 Ton Production Note This machine is manufactured by CRONOSSTECH in Turkey.

Condition: new, Year of construction: 2025, pressing force: 200 t, stroke length: 800 mm, table width: 1,000 mm, table length: 1,200 mm, retraction force: 70 t, operating pressure: 250 bar, Equipment: documentation/manual, safety light barrier, CRONOSSTECH CHSP 200/70 H-Type Hydraulic Deep Drawing (Flanging) Press – 8 Slideways General Description The CRONOSSTECH CHSP series H-type hydraulic deep drawing presses are designed with a double-acting working principle to ensure controlled material flow in sheet metal forming, deep drawing, and flanging applications. The 8-slideway H-frame construction provides maximum rigidity during pressing operations, maintaining parallelism and perpendicularity tolerances consistently throughout the stroke. The CHSP 200/70 model, featuring a 200-ton main ram and a 70-ton lower blank holder (pot) capacity, is engineered for medium-to-high tonnage deep drawing and flanging processes. The frame structure undergoes vibratory stress relief for long-lasting and reliable performance. ⚙️ Standard Equipment - Steel construction, H-frame press body with 8 slideways - Vibratory stress-relieved frame - Bronze Zr14 slideway bearings - Welding processes verified by TÜRK-AK accredited WPQR and WPS certificates (EN ISO 15614-1:2017 / EN ISO 14731 compliant) - Design and manufacturing in accordance with CE standards - PLC-controlled hydraulic system - 7” DELTA touchscreen panel - Adjustable ram and pot stroke control - Adjustable ram and pot tonnage (pressure) control - Automatic lubrication system - Electronically monitored filter contamination warning - On-screen monitoring of hydraulic unit oil temperature and system status - Cooling system - Off-line filtration - Safety interlock systems for operator protection - SIEMENS – SCHNEIDER switchgear components 📐 Technical Specifications – CHSP 200/70 Type: Steel construction, H-frame with 8 slideways Frame Material: St52 – ERDEMIR Slideway Bearings: Bronze Zr14 Capacity (Ram): 200 tons Capacity (Pot): 70 tons Movable Table Dimensions: 1000 × 1200 mm Fixed Table Dimensions: 1000 × 1200 mm Parallelism Tolerance: 120 microns/meter Perpendicularity Tolerance: 60 microns/meter Ram Stroke: 800 mm Pot Stroke: 300 mm Min. Daylight: 100 mm Max. Daylight: 900 mm Weld Stress Relief: Vibratory stress relief Welding Application: WPQR and WPS certified by TÜRK-AK according to EN ISO 15614-1:2017 (Supervised by certified "welding coordination engineers" as per EN ISO 14731) Max. Working Pressure: 250 Bar Total Motor Power: 22 kW – IE3 Main Pump: 32 cm³ – REXROTH or PARKER Movable Table Rapid Down Speed: 150 mm/s Movable Table Drawing Speed: 12 mm/s Nodpfjx N T U Tjx Acfewh Movable Table Return Speed: 170 mm/s Pot Table Forward Speed: 30 mm/s Main Cylinder Bore: Ø320 mm – Ck45 Pot Cylinder Bore: Ø190 mm – Ck45 Auxiliary Acceleration Cylinders: 2 Units Approx. Height of Press: 3800 mm Approx. Width of Press: 2950 mm Approx. Depth of Press: 2200 mm Distance from Floor to Lower Table: 1350 mm Pre-fill Valve: NG 125 Hydraulic Unit: REXROTH or PARKER Cooling System: EMMEGI – CIESSE – PARKER Off-line Filtration: REXROTH or PARKER Linear Position Scale: NOVATECHNIK or TURCK PLC: DELTA Touchscreen Panel: DELTA 7” Switchgear: SIEMENS – SCHNEIDER Approximate Weight: 13.5 tons Production Note This machine is manufactured by CRONOSSTECH in Turkey.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Nsdpfxsy S Rqws Acfewh Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. Nwodezdn H Repfx Acfoh We accept no liability for the technical specifications or any errors.

Condition: good (used), Screw bookbinding press 40×30 with base Nwodezdat Repfx Acfoh The machine is fully operational and ready for operation. Format: 400×300 mm Pressure: 3 tons Made in Germany.

Condition: good (used), Bookbinding press with tapping block Nwjdezdatqepfx Acfeh The machine is fully operational and ready for use. Approximate format: 480 x 330 mm 3-ton pressure

Condition: excellent (used), Year of construction: 1989, functionality: fully functional, WE OFFER AN BEAUTIFULL CONDITION DEEP DRAWN PRESS 160 TON WITH BACK FORCE BOTTOM 70 TON MACHINE WAS BUILD ON ORDER MACHINE WAS USED ONLY A COUPLE TIMES PER YEAR FOR SOME SMALL PARTS. CONDITION IS EXCELLENT . NEWER RUN A PRODUCTION. WE CAN ALSO DELIVER MACHINE FOR A CUSTOMER TABLE SIZE: 1030 X 630 Nwjdpfx Acevxbn Usfeh OPEN GAP: 740 MM TOTAL WEIGHT APPROX 8000KG DIMENSION 1500 X 1500 X 4000

Condition: used, Year of construction: 2012, operating hours: 53,154 h, functionality: fully functional, pressing force: 120 t, filling opening width: 1,800 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 730 mm, total width: 4,700 mm, total height: 4,600 mm, total length: 13,100 mm, overall weight: 28,000 kg, warranty duration: 12 months, Equipment: documentation/manual, For sale is a bale press, model "EP 1000 V5 H3," manufactured in 2012, featuring both horizontal and vertical tying mechanisms. The pictures show the machine in its assembled state. It is currently located at our facility in Lathen. The press is sold without a conveyor belt. Prior to delivery, the machine will be completely overhauled and technically refurbished by our qualified technicians. Our goal is to provide you with a reliable and immediately operational machine that meets the requirements of daily operation. The overhaul includes, among other things, the following services: • Disassembly and inspection of relevant machine components • Evaluation of all wear-related components • Replacement or refurbishment of worn parts • Inspection and repair of the press ram and associated guide elements • Inspection and, if necessary, replacement of wear plates, sliding guides, and bearing points • Inspection of the press channel and restoration of the required tolerances • Overhaul of hydraulic components, including cylinders, valve technology, and hydraulic hoses • Replacement of seals, wear parts, and fasteners Njdpjzggd Tefx Acfowh • Inspection of electrical components and safety devices • Inspection and readjustment of the tying mechanism • Cleaning, assembly, and commissioning of the overhauled system • Performance of functional and load tests after completion of the work Through this comprehensive overhaul, you will receive a technically inspected machine with high operational reliability and a long service life. We would be happy to provide you with further information, photos, or a customized offer. If you are interested, please do not hesitate to contact us.

Condition: used, Year of construction: 2010, operating hours: 4,054 h, functionality: fully functional, pressing force: 90 t, filling opening width: 1,450 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 730 mm, total width: 2,500 mm, total height: 3,850 mm, total length: 12,000 mm, overall weight: 23,000 kg, warranty duration: 12 months, power: 90 kW (122.37 HP), Equipment: documentation/manual, For sale is a baling press, model "EP 6100 V5", manufactured in 2010. Prior to delivery, the machine will be completely overhauled and technically refurbished by our qualified personnel. Our goal is to provide you with a reliable and immediately operational machine that meets the requirements of daily operations. The overhaul includes, but is not limited to, the following services: • Disassembly and inspection of relevant machine components • Assessment of all wear-related components • Replacement or refurbishment of worn parts • Inspection and repair of the press ram and associated guide elements • Inspection and, if necessary, replacement of wear plates, sliding guides, and bearing points • Inspection of the press channel and restoration of the required tolerances • Overhaul of hydraulic components, including cylinders, valve technology, and hydraulic hoses • Replacement of seals, wear parts, and connecting elements • Inspection of electrical components and safety devices Nwedpfxszggans Acfoh • Inspection and readjustment of the bale tying mechanism • Cleaning, assembly, and commissioning of the overhauled machine • Performance of functional and load tests after completion of the work Thanks to the comprehensive overhaul, you will receive a technically inspected machine with high operational reliability and a long service life. We will be happy to provide you with further information, photos, or a customized offer. If you are interested, we look forward to hearing from you.

Condition: used, Year of construction: 2009, functionality: fully functional, pressing force: 60 t, filling opening width: 1,000 mm, filling opening length: 1,450 mm, bale length: 1,800 mm, bale width: 1,100 mm, bale height: 750 mm, total width: 2,500 mm, total height: 3,500 mm, total length: 9,255 mm, overall weight: 14,000 kg, warranty duration: 12 months, transport height: 2,587 mm, transport width: 2,500 mm, transport length: 6,645 mm, Equipment: documentation/manual, For sale is a bale press, model EP 6000 V5, manufactured in 2009. Before delivery, the machine will be completely overhauled and technically refurbished by our qualified personnel. Our goal is to provide you with a reliable and immediately operational machine that meets the demands of daily operation. The overhaul includes, among other things, the following services: • Disassembly and inspection of relevant machine components Nodjzgf Hgspfx Acfowh • Evaluation of all wear-relevant components • Replacement or refurbishment of worn parts • Inspection and repair of the press ram and associated guide elements • Inspection and, if necessary, replacement of wear plates, sliding guides, and bearing points • Inspection of the press channel and restoration of the required tolerances • Overhaul of the hydraulic components, including cylinders, valve technology, and hydraulic hoses • Replacement of seals, wear parts, and connecting elements • Inspection of the electrical components and safety devices • Inspection and readjustment of the bale tying device • Cleaning, assembly, and commissioning of the overhauled system • Performance of functional and load tests after completion of the work Thanks to the comprehensive overhaul, you will receive a technically inspected machine with high operational reliability and a long service life. We would be happy to provide you with further information, photos, or a customized offer. If you are interested, we look forward to hearing from you.

Condition: good (used), Year of construction: 2015, functionality: fully functional, Baling press Dixi 60 SLD, year of manufacture 2015 Manufacturer: Dixi Type: Dixi 60 SLD Year of manufacture: 2015 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-fold, manual Nwjdpfxozgvbue Acfoh Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine weight: approx. 5,420 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. The operating manual and CE declaration are available. We will be happy to answer any questions you may have about the machine by telephone from Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available for you from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and for any errors. The offer is subject to change, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment ex works, without warranty.

Condition: good (used), Year of construction: 2016, operating hours: 1,060 h, functionality: fully functional, Baling press Dixi 80 SLD, with lifting/tilting device, semi-automatic, year of manufacture 2016 Manufacturer: Dixi Type: Dixi 80 SLD Year of manufacture: 2016 Operating hours: 1030 Drive power: 11 kW, 400 V / 23 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Pressing cycle: approx. 35 s Nsdpey Ni Shjfx Acfewh Capacity: approx. 1000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 3-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film Note: The press is in very good condition. It has been inspected and tested at our facility in 28816 Stuhr. The video can be found on our website or our YouTube channel. The hydraulic hoses should be replaced. We will gladly answer any questions you have about the machine by phone from Monday to Thursday from 08:00 to 14:00. On Friday, we are available to you from 08:00 to 13:00. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without warranty.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Bale press Dixi 80 SLD, with lifting/tilting device, semi-automatic, year of manufacture 2017 Manufacturer: Dixi Type: Dixi 80 SLD Year of manufacture: 2017 Drive power: 11 kW, 400 V / 21 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Pressing cycle: approx. 35 s Nwsdpfjy Ni I Ajx Acfoh Capacity: approx. 1,000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. We will be happy to answer any questions you may have about the machine by telephone from Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2013, functionality: fully functional, Baling press Dixi 60 SLS, year of manufacture 2013 Technical data: Manufacturer: Dixi Year of manufacture: 2013 Pressing force: 60 t Drive power: 11 kW, 23 A Feed opening: 990 x 1110 mm (W x L) Bale dimensions: 1100 x 800 x 1200 mm Bale weight: approx. 370-450 kg Tying: 3-fold manual Machine dimensions: approx. 4870 x 2100 x 2150 mm (L x W x H) Weight: approx. 5220 kg Materials: Paper, cardboard, film The press is in good, fully functional condition and has been inspected and tested by us. You can find the video on our website or YouTube channel. We will be happy to answer any questions you may have about the machine by phone, Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available to you from 8:00 a.m. to 1:00 p.m. Nwodpfxoy Ni Hro Acfsh Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any errors that may occur. The offer is non-binding, subject to prior sale, and may be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without warranty.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Baling press Dixi 60 SLD, year of manufacture 2012 Manufacturer: Dixi Type: Dixi 60 SLD Year of manufacture: 2012 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-strand, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine weight: approx. 5,420 kg Material: Paper, cardboard, film The press is in good condition. We will gladly answer any questions you have about the machine by phone, Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available from 8:00 a.m. to 1:00 p.m. Njdpjy Ni Dqsfx Acfjwh Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is non-binding, subject to prior sale and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2015, functionality: fully functional, Baling press Dixi 60 SLD, year of manufacture 2015 Manufacturer: Dixi Type: Dixi 60 SLD Year of manufacture: 2015 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-fold, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine weight: approx. 5,420 kg Materials: Paper, cardboard, film Nwsdpfx Aey Ni Euscfeh The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. The operating manual and CE declaration are available. We will be happy to answer any questions you may have about the machine by telephone from Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available for you from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and for any errors. The offer is subject to change, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment ex works, without warranty.

Condition: used, Year of construction: 2003, Technical details: Nwedpfxezgvhue Acfoh pressure: 58 t box depth: 1145 mm material: Papier/Pappe/Kartonage/Plastik/Blechdosen/PET Flaschen bottles Feed opening: L: 1145 x B: 600 mm voltage: 400V / 50 V / Hz total power requirement: 4,0 kW weight of the machine ca.: 2,6 t machine dimensions LxWxH: ca. 1,07 x 1,84 x 3,1 m Anwendung: Papier/Pappe/Kartonage/Plastik/Blechdosen/PET Flaschen platzsparende Recycling Lösung kompakte Bauart automatische Pressplattenrückführung, dadurch erhöhter Bedienkomfort Öffnung an der Vorderfront Tür horizontal verschiebbar ca. 600mm Presskammer/Ballengröße: LxBxH: 1000 x 600 x 600 mm (0,36 m³) Bindeeinheit Band- und/oder Drahtabbindung Bedienung über Schalttafel *

Condition: used, Year of construction: 2005, Technical details: pressure: 58 t box depth: 1145 mm material: Papier/Pappe/Kartonage/Plastik/Blechdosen/PET Flaschen bottles Feed opening: L: 1145 x B: 600 mm voltage: 400V / 50 V / Hz total power requirement: 4,0 kW weight of the machine ca.: 2,6 t machine dimensions LxWxH: ca. 1,07 x 1,84 x 3,1 m Anwendung: Papier/Pappe/Kartonage/Plastik/Blechdosen/PET Flaschen platzsparende Recycling Lösung kompakte Bauart automatische Pressplattenrückführung, dadurch erhöhter Bedienkomfort Öffnung an der Vorderfront Tür horizontal verschiebbar ca. 600mm Presskammer/Ballengröße: LxBxH: 1000 x 600 x 600 mm (0,36 m³) Bindeeinheit Band- und/oder Drahtabbindung Bedienung über Schalttafel Nwjdpfx Acjzgvhhefjh *

Condition: refurbished (used), MAE Hydraulic Press 25 Ton Details Manufacturer: MAE. Type: HY-S25. Condition: Refurbished. Specifications Press force: 25 tons Nwsdpfjzd Shfex Acfjh Frame type: C-frame Drive: Hydraulic Stroke: approx. 400 mm Table surface: approx. 800 × 500 mm Motor power: approx. 5.5 kW Hydraulic tank capacity: approx. 140 liters Operation: Two-hand operation. Dimensions Length: approx. 950 mm. Width: approx. 1700 mm. Height: approx. 2900 mm. Weight: approx. 4000 kg.

Year of construction: 2020, condition: ready for operation (used), A paper and cardboard baling press Bema is available. Motor power: 2.2kW, pressing force: 20t, opening dimensions X/Y: 596mm/1200mm, bale dimensions X/Y/Z: 1200mm/800mm/1000mm, max. bale weight: 300kg, cycle time: 40s, hydraulic oil filling: 24l, machine dimensions X/Y/Z: approx. 1800mm/1100mm/1950mm, weight: approx. 1150kg. Documentation available. An on-site inspection is possible. Nwodpjzfp Hzofx Acfoh

Condition: good (used), Year of construction: 1996, 2 pieces Fab. Hofmann Year of construction 1996 Bale size (channel size)= 80 x 60 cm Bale weight e.g. hay = 220 kg/bale with 1.4 m bale length Hydr. baling pressure = 300 bar Automatic bale tying with 3 wires Ø 3.1 mm Baling capacity approx. 5 t/h Motor power = 18 kW incl. collecting screw under baler Nodpertngcofx Acfswh incl. electrical control with Wago PLC (year of manufacture 2022) undismantled