Used Fliegl Dts S 300 Parab/Hydr. for sale (77,599)

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Kdjdji Ri Dljpfx Afdjk Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Kjdpei Ri Ddofx Afdodk Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, empty load weight: 5,740 kg, maximum load weight: 24,260 kg, overall weight: 30,000 kg, axle configuration: 3 axles, color: silver, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, rotating beacon, 3 axles, SAF axles, turntable, leaf suspension, ABS (anti-lock braking system), extendable to 3m width, lashing rings, 2-piece loading ramps, mechanical ramps, extendable drawbar, side aluminium underrun protection, twin tyres, EBS. Body: loading length approx. 8.5m, extendable to 3.05m. Demonstration vehicle! Parabolic suspension with axle compensation at the rear, 3 x 10t SAF axles, permissible gross weight up to 30t possible, drawbar adjustable in length. New vehicle from stock with day registration to the manufacturer! ACCESSORY INFORMATION WITHOUT GUARANTEE. Subject to change, prior sale, and errors! Kedpfxjxbttqo Afdodk

Condition: new, machine/vehicle number: 408ba9a39bbb8087056d6e563, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope Kedsi Ri Daepfx Afdodk 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: used, empty load weight: 6,520 kg, maximum load weight: 23,480 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 05/2019, loading space length: 8,610 mm, suspension: air, tire size: 235/75R17,5 ---/140J, color: other, gearing type: other, front tire size: 235/75R17,5 ---/140J, rear tire size: 235/75R17,5 ---/140J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Loading area length drop deck approx. 6.50 m, loading area length total approx. 8.60 m, loading height approx. 900 mm, , Vehicle is offered on behalf of a bank, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Kdodpfxey Di Ulj Afdek

Condition: used, axle configuration: 3 axles, Year of construction: 2018, Equipment: ABS, = Additional Options and Equipment = - Rear air suspension - Front air suspension Kedpoy Adc Isfx Afdedk = Notes = For vehicle inquiries, Mr. Seidel will gladly assist you (by phone). Fliegl DTS 300 Low Loader BPW axles, drum brakes, spring-loaded brakes, mechanical ramps, permissible gross weight: 24,000 kg, unladen weight: 6,350 kg, payload: 17,650 kg, cargo area dimensions: L 8,490 mm x W 2,510 mm, tire tread: 1st axle 7-12 mm, 2nd axle 7-8 mm, 3rd axle 4-7 mm On request, we can provide you with a leasing or financing offer. Mr. Seidel (phone) will be happy to assist you. Further information can be found on our homepage. ... Errors, changes, and prior sale excepted!!! - = Further Information = Unladen weight: 6,350 kg Payload: 17,650 kg Gross weight: 24,000 kg External dimensions: 0 x 2,550 x 3,500 Please contact Tobias Ebert for further information.

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Kodpei Ri Rvofx Afdjdk Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Kdedei Riy Eepfx Afdjk Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: ede0610378cbe39cc4883251d, empty load weight: 24,000 kg, maximum load weight: 7,550 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction 1st pair of wheel recesses after steel platform recessed in the tramline area, inclined towards the entrance, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. If machines are to be driven where the overall height is to be checked, we request a technical data sheet for the machine types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer). Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 110 3 pairs of lashing points, 10 tons each, integrated in the floor at the front Incl. 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x to neck area remaining distributed in between Distance not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles which guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Twin steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear Kedpfx Afji Ri Ryodjdk 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, incl. Afterwards with 70 mm softwood floor, steel/checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. cannot be achieved. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Incl. with

Condition: new, machine/vehicle number: f8fb99947a1c19bc4d63549ff, empty load weight: 6 kg, maximum load weight: 17 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 7 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion with M&S marking Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front Kdjdpfoi Riwfox Afdok 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Coun

Condition: new, machine/vehicle number: 15431365fe5515297a6a9fb05, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Kdjdpfxei Ri A Sj Afdek Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: used, first registration: 09/2016, color: other, Year of construction: 2016, Equipment: ABS, = Additional options and accessories = - BPW-Assen - Drum brakes - Lift Axle = Remarks = Fliegl, 2016, BPW axles, Axle 1 Liftable, Drum brakes = Dealer information = Kdjdjy Avafopfx Afdjk Bank data: Rabobank Account: 39.33.10.655 IBAN: NL73RABO0393310655 Swift code: RABONL2U - Always check our bank details before transaction! - Reservation of vehicles is not possible without a deposit. - Writing and text errors are reserved for all vehicles offered.

Condition: used, overall weight: 41,000 kg, axle configuration: 3 axles, first registration: 04/2023, next inspection (TÜV): 05/2026, Year of construction: 2023, Equipment: ABS, * Fliegl SDS 470 low-loader * First registration: 04-2023 * Hydraulic lifting bed * 9-ton winch with remote control * Hydraulic double ramps * Last axle is force-steered * SAF axles * Curb weight: 11,800 kg * Gross weight: 41,000 kg * More pictures and videos via Whatsapp Kdjdpfeyq A Uqex Afdsk * Information subject to change and prior sale.

Condition: used, mileage: 62,500 km, power: 130 kW (176.75 HP), first registration: 10/2011, fuel type: diesel, empty load weight: 8,410 kg, maximum load weight: 1,090 kg, overall weight: 9,500 kg, tire size: 365/80R20, axle configuration: 4x4, wheelbase: 3,080 mm, color: orange, driver cabin: day cab, gearing type: semi-automatic, emission class: euro5, suspension: steel, number of seats: 3, Equipment: ABS, additional headlights, air conditioning, all wheel drive, cabin, differential lock, low noise, onboard computer, power assisted steering, seat heater, trailer coupling, Vehicle location: Bovenden, county Haus, 1x comfort seat, double passenger bench, seat heating, rear window, electric window left, electric window right, air conditioning, Telligent gearshift, differential lock, high beam headlights, work lights, rotating beacon, leaf spring suspension, trailer coupling (air + electrics), aluminum fuel tank, low-noise G1, winter service equipment, green environmental sticker. Kdedpfxexylpbj Afdek Wheelbase: 3,080 mm. Differential lock on front axle, dual-line trailer brake system, radiator protection grilles behind both radiators, auxiliary heater with engine pre-heating, fine dust and pollen filter, split-range gearbox with work group, torque converter clutch (WSK), VarioPower, pressure and return line at front for hydraulic circuits 3+4, dual-circuit hydraulic system with four chambers, snowplow relief function, acoustic reverse warning, rear-mounted PTO with flange. The vehicle is sold with a flatbed body! Approx. 5,413 operating hours! Optional: Gmeiner salt spreader available for an additional EUR 6,500 and snow plow -9161- for an additional EUR 1,500! ACCESSORY DETAILS WITHOUT GUARANTEE. Subject to changes, prior sale, and errors!

Condition: like new (used), functionality: fully functional, Year of construction: 2022, operating hours: 347 h, load capacity: 3,000 kg, lifting height: 4,980 mm, free lift: 1,495 mm, load center: 500 mm, fuel type: electric, mast type: triplex, construction height: 2,280 mm, gearing type: hydrostat, battery model: 90V 42.2kWh 496Ah Li ion batterij, battery capacity: 496 Ah, battery voltage: 90 V, fork carriage width: 1,150 mm, fork length: 1,200 mm, front tire type: superelastic tires (non-marking), rear tire type: superelastic tires (non-marking), Equipment: CE marking, air conditioning, cabin, full service history, gripper hydraulics, lighting, pallet forks, seat heater, sideshift, For Sale: Linde X30-01 Forklift (2022) – Top Quality at 2BRO-Trading BV in Mol, Belgium Are you looking for a powerful and reliable forklift? At 2BRO-Trading BV in Mol, Belgium, we have a Linde X30-01 from 2022 available, fully equipped with high-end options and excellent service. This machine is immediately ready for use and perfectly suited for intensive operation in various work environments. 🔥 Specifications of the Linde H35D-01: ✅ Brand: Linde ✅ Model: X35-01 ✅ Year of manufacture: 14-07-2022 ✅ Operating hours: 347 hours (verified via Linde computer) ✅ Chassis number: H21252L01309 🚀 Powerful Mast and Lifting Performance: ✔️ Mast type: Free-Lift Triplex ✔️ Max. lift height: 4,980 mm ✔️ Max. overall height: 2,280 mm ✔️ Free lift height: 1,495 mm ✔️ Fork carriage: FC 1,150 mm / 6Ro / 3.5 ton (FEM 3A) ✔️ Hydraulic functions: 3rd, 4th, and 5th function (for rotator clamp, fork positioner, sideshift, etc.) 🚜 Comfort and Safety-Oriented Features: ✔️ VIEW Comfort Cabin (height: 2,280 mm) with: Left and right doors Front, rear and top windows with wipers Heated rear window Air-suspended Comfort seat in PVC + seat heating Cabin heating Air conditioning Panoramic mirror Adjustable steering column DAB+ Radio Configuration buttons F1-F4 Configuration buttons A1-A6 Integrated weighing system Dual pedal system (convertible to single pedal) Linde LLC joystick Keyless ignition with code lock (also convertible) LED road, work, and safety lighting Rear motion detection Kedpfxoyzzdys Afdodk Mast cushioning Continental CS20 non-marking tires 🔥 Maintenance: ✔️ Complete 1,000-hour maintenance service performed ✔️ Up-to-date software and settings ✔️ Includes new BMWT inspection (valid for 1 year) 💪 Why choose 2BRO-Trading BV? ✅ Professional Service: We use an official Linde LSG diagnostic computer for rapid configuration, updates, and fault diagnosis. ✅ Fast On-Site Service: Breakdowns are resolved quickly – we ensure your forklift is operational again as soon as possible! We strive to keep our clients’ operations running! ✅ Replacement Forklift: In case of breakdown, we can provide a temporary replacement forklift so your work can continue. ✅ Mobile Service Van: Our fully equipped service van allows us to carry out maintenance and most repairs directly at your location. ✅ Flexible Configuration: All travel and lift speeds can be adjusted to your needs after delivery – we return in 1-2 weeks for final fine-tuning. 🚨 Don’t miss this opportunity! The Linde X35-01 from 2023 is in excellent condition and ready for immediate use. Contact 2BRO-Trading BV in Mol, Belgium today for more information or a viewing! 📞 Call or email us now – We are happy to assist you!

Condition: new, Year of construction: 2025, sheet thickness steel (max.): 6 mm, cutting length (max.): 3,050 mm, Guillotine shears: Available immediately! General performance features: Cutting length: 3100 mm Maximum sheet thickness: 6 mm (mild steel), 4 mm (stainless steel) Projection in the side stand: 50 mm Number of strokes: 15 per minute Cutting angle: 1° Number of hold-down devices: 16 Hold-down pressure: 14 tons Backgauge: Up to 1000 mm Backgauge speed: 200 mm/s Motor power: 15 kW Oil tank volume: 200 liters Support arms: 2 pieces Table dimensions: 865 mm (height) x 500 mm (width) x 3515 mm (length) Ksderx Sydspfx Afdjdk Dimensions and weight: Length: 4110 mm Width: 2200 mm Total width (with support arm and rear protective grille): 3700 mm Height: 2100 mm Weight: 7650 kg This guillotine shear is the ideal addition to your workshop, taking efficiency and precision to the next level. Get this high-quality machine for demanding metalworking projects. Contact us now for more information and a personalized quote!

Condition: new, machine/vehicle number: b50cac2c60a813b0968994fa0, empty load weight: 5,700 kg, maximum load weight: 18,300 kg, overall weight: 24,000 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Kdsdpfx Aei Ri Agsfdek Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Rear spray flaps across the entire width Preparation for widening to 3,000 mm (holes in the outer frame and not in the rear slope) Low loader lashing eyes 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 5 x in the drop deck 1 x in the rear slope 12 pairs of lashing holes in the outer frame, each with 5 to. (lashing strap attachment) 5 x crank, 6 x low bed and 1 x in rear slope Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17.5 Fulda Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, Connecting lines extended by approx. 60 cm without ABS, but with mechanical ALB, then max. 60 km/h approval Electrical system 12 volt, multi-chamber lights, without amber LED lighting at the sides, reflectors at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 7-pin 12 volt plug at the front, with connecting cable, extended by approx. 60 cm 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, illuminated and extendable to 3,000 mm, floor Front offset with steel/ checker plate covering Storage box recessed in drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 5900 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion, for max. 60 km/h registration, towing vehicle LoF, (max. 40 km/h possible in Switzerland) Prepared for two-line license plate holder without contour marking / reflective strips according to ECE R 048, Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, Year of construction: 2026, Drum chipper series ATH S&F chippers and drum chippers with horizontal infeed are used in many areas of the wood processing industry (sawmills, timber mills). Chippers from the ‘ATH’ series produce high-quality and homogeneous wood chips with a low proportion of fines from residual wood, for example as quality chips for the cellulose industry or as fuel chips for energy generation Ksdpfx Ajuz Hmxefdjdk ATH 220 series - Feed height: 200 mm - Feed width: 500 | 700 | 1000 mm - Number of chipper knives: 2 - 4 pieces - Number of counter knives: 2 pieces - Rotor diameter:520 mm - Number of feed rollers: 3 pieces - Throughput: up to approx. 40 rm/h * - Chipping length: 5 - 50 mm - Chipper drive power: 22 - 110 kW - Drive power feed rollers: 2 x 2.2 kW - Operating/control voltage: 400/220 V, 50 Hz - Weight: 2,800 - 4,000 kg ATH 330 series - Feed height: 300 mm - Feed width: 500 | 700 | 1000 mm - Number of chipper knives: 2 - 6 pieces - Number of counter knives: 2 pieces - Rotor diameter: 700 mm - Number of feed rollers: 3 pieces - Throughput capacity: up to approx. 70 rm/h * - Chipping length: 5 - 80 mm - Chipper drive power: 37 - 250 kW - Drive power feed rollers: 2 x 3.0 kW - Operating/control voltage: 400/220 V, 50 Hz - Weight: 3,500 - 5,000 kg *depending on chipper length, kW main motor, number of knives, feed Advantages: - Maximum throughput - Low fines content - Low maintenance - Flexible use - Customised production

Condition: used, mileage: 135,996 km, power: 110 kW (149.56 HP), first registration: 04/2001, overall weight: 9,500 kg, fuel type: diesel, color: orange, axle configuration: 2 axles, gearing type: mechanical, emission class: euro3, Year of construction: 2000, Equipment: ABS, air conditioning, all wheel drive, Equipment: - Split-range gearbox with work groups - Towing jaw coupling (Maul-AHK) with full brake system - Tipping cylinder - Engine-driven PTO including front PTO - Driver’s suspension seat - Double passenger bench seat - Rear cab window - Rotating beacons - Additional work lights Municipal specification: - Front mounting plate, size 3 - Two-circuit hydraulic system - 4-cell hydraulic system - Separate return line at rear - Snowplough relief function - Hydraulic connector sockets: - Front: four-pole cell 1+2+3+4 - Rear: four-pole cell 2+3 - Prepared for high-performance hydraulics - Pressure and separate return line midships on 2nd circuit - Front pressure line for 2nd hydraulic circuit Miscellaneous: - First delivered in Germany - 2 previous owners - 3,770 kg payload according to registration - Downgrade to 7,500 kg possible Kdjdpfjrt Aypsx Afdok Since 1972, your reliable partner for automobiles and commercial vehicles in 28832 Achim at the Bremer Kreuz. NutzfahrzeugZentrum Behnke always stocks around 200 vehicles in the areas of vans, commercial vehicles, and construction machinery! We continuously offer attractive financing solutions with favorable special rates. Please contact us for a tailored quotation! Trade-in of your commercial vehicle or construction equipment is welcome. If a new TÜV inspection is desired, we are happy to provide a quote from our partner workshops. Our offers are generally WITHOUT new TÜV inspection. Delivery of your 'new' commercial vehicle can be arranged through our external partners for an additional fee. The information provided in advertisements, online listings, price tags, and images are non-binding descriptions and do not constitute guaranteed properties. The seller assumes no liability or warranty for typographical and data transmission errors. Listed equipment may need to be checked separately. Subject to prior sale and errors.

Condition: used, mileage: 135,996 km, power: 110 kW (149.56 HP), first registration: 04/2001, overall weight: 9,500 kg, fuel type: diesel, color: orange, axle configuration: 2 axles, gearing type: mechanical, emission class: euro3, Year of construction: 2000, Equipment: ABS, air conditioning, all wheel drive, Equipment: - Split gearbox with work ranges - Piton-fix trailer hitch with continuous braking system - Tipping cylinder - Engine-driven PTO including front PTO - Driver's suspension seat - Dual passenger bench seat - Rear window - Rotating beacons - Additional work lights Municipal Equipment: Kodpfx Aot Ex Uusfdedk - Front mounting plate, size 3 - Dual-circuit hydraulic system - 4-cell hydraulic system - Separate return line at the rear - Snow plow relief - Hydraulic connector couplings: - Front: 4-way cell 1+2+3+4 - Rear: 4-way cell 2+3 - Pre-installation for high performance hydraulics - Pressure line + separate return line, center 2nd circuit - Pressure line front for 2nd hydraulic circuit Miscellaneous: - First delivered in Germany - 2 previous owners - 3,770 kg payload according to registration certificate - Downrating to 7,500 kg possible Since 1972, your reliable partner for cars and commercial vehicles in 28832 Achim at Bremer Kreuz. NutzfahrzeugZentrum Behnke always has around 200 vehicles in stock, including vans, commercial vehicles, and construction machinery! We continuously offer attractive financing options at special rates. If interested, we will gladly provide you with an individual offer! Trade-in of your commercial vehicle/construction machine is desired. If a new TÜV inspection is required, we can offer this through our partner workshops. Our offer generally does NOT include a new TÜV inspection. Delivery of your "new" commercial vehicle can be arranged by our external partners for an additional charge. The information provided in advertisements, on the internet, on price tags, and in images are non-binding descriptions and do not constitute guaranteed characteristics. The seller assumes no liability or warranty for errors in typing or data transmission. Listed equipment must be verified separately if needed. Subject to errors and prior sale.

Condition: used, power: 13 kW (17.68 HP), Year of construction: 2021, operating hours: 143 h, Drive: Track Kdedpfx Afeq Dmaxedok Empty weight: 1.090 kg Make of engine: Yanmar Serial number: CAT3009DELJM03293 Tyre brand: - Transport dimensions (LxWxH): 2.75x0.71x2.28 Please contact PFEIFER GROUP for more information

Condition: used, power: 13 kW (17.68 HP), Year of construction: 2021, operating hours: 92 h, Drive: Track Empty weight: 1.090 kg Make of engine: Yanmar Serial number: CAT3009DELJM03245 Tyre brand: - Transport dimensions (LxWxH): 2.75x0.71x2.28 Please contact PFEIFER GROUP for more information Ksdpfx Afoq Dlqdsdodk

Condition: good (used), Year of construction: 2001, The Fladder 300/GYRO is a machine designed for processing flat surfaces (e.g., sheets, aluminum parts, steel components, or plastics). Main applications: - Deburring (removal of sharp edges), - Cleaning surfaces after laser, plasma, or punching processes, - Edge rounding, - Surface preparation for painting/coating, - Removal of rust, scale, and residual oxides. Technical specifications: Model: Fladder 300/GYRO-1300 VAC Kdsdew Uabpjpfx Afdok Working width: 1300 mm Power supply: 3 × 400 V, 50 Hz Current consumption: 63 A Protection class: IP54 Motors: independent drives for working units and conveyor belt Conveyor belt feed speed: adjustable GYRO system: orbital-rotational working heads (uniform deburring and surface finishing) Equipment: conveyor belt with dust extraction (VAC), control panel, emergency STOP button Year of manufacture: 2001 Machine in good technical condition Complete, ready for operation On-site inspection possible

Condition: used, power: 13 kW (17.68 HP), fuel type: diesel, Year of construction: 2021, operating hours: 143 h, Drive: Track Empty weight: 1.090 kg Kdsdpfx Afotr Hyqsdek Make of engine: Yanmar Serial number: CAT3009DELJM03293 Tyre brand: - Transport dimensions (LxWxH): 2.75x0.71x2.28 Please contact PFEIFER GROUP for more information

Condition: used, mileage: 18,709 km, power: 330 kW (448.67 HP), first registration: 04/2024, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, color: beige, gearing type: automatic, emission class: euro6, Year of construction: 2023, Equipment: ABS, air conditioning, all wheel drive, navigation system, soot filter, Like New / Original Mileage / Immediately Ready for Use Body: - Body type: Hook Lift, - Model: Hyva 26-51-S, - Hydraulic locking - Mechanical underrun protection - Crane hydraulics - Net box Equipment: - Cab: M ClassicSpace, 2.30 m, 320 mm tunnel, - Air conditioning, - Comfort air-suspension driver's seat, - High engine tunnel storage compartment, - Tinted windscreen with band filter, - Rear cab window, - Cab: steel suspension, comfort version, - 50 mm trailer coupling with 2-line trailer brake, - Front axle load 8.0 t, - Suspension: front springs 8.0 t, 3-leaf, - Suspension: rear springs 2x10 t, heavy-duty, - 12-speed gearbox - type: G 330-12, - Rear axle with 300 mm crown wheel, - Cabin filter for construction vehicles, - Cooling system for hot climates, - Cyclone air filter, - Rear engine PTO, - 290-liter tank with protection plate, - Twin-plate clutch, - Manual sunroof (steel), Technology: - Navigation system, - Multifunction steering wheel, - Audio system: Digital radio DAB / DAB+, - Interactive multimedia cockpit, - Rotating beacon, - Preparation for 4 surround cameras (display on vehicle monitor), - Rain sensor, - Circuit breaker, - Heated entry/front mirrors, - Automatic driving light activation (light sensor), - Electric windows, Safety / Environment: - Enhanced engine brake, - Switchable all-wheel drive, - Front axle differential lock, - Emission standard EURO 6, Other: - First delivery in Germany - 1 previous owner - Wheelbase variant 3900 mm, - Axle configuration: 6x6, - Model: Arocs 5, A - Suspension: leaf/leaf, - Engine: 12.8 Litre - 330 kW R6 Diesel (OM 471), - PTO MB 131-2c, - Permissible gross weight 26,000 kg, Kdsdpfx Afjy Eakaedok - COC documentation available - Max. gross train weight 66 t - Like new condition Since 1972, your reliable partner for automotive and commercial vehicles in 28832 Achim, near Bremer Kreuz. NutzfahrzeugZentrum Behnke constantly offers approx. 200 vehicles from the fields of vans, commercial vehicles, and construction machinery. We continuously offer attractive financing options at favorable special rates. If interested, we are happy to provide a tailored offer! Trade-in of your commercial vehicle/construction machine is welcome. If a new technical inspection (TÜV) is required, we are happy to provide you with an offer from our partner workshops. Our offer is generally WITHOUT a new technical inspection. Delivery of your "new" commercial vehicle is available through our external partners at an additional charge. The information provided in advertisements, on the internet, price tags, and pictures is non-binding and does not represent guaranteed characteristics. The seller assumes no liability or warranty for typographical or transmission errors. Listed equipment may need to be verified separately. Subject to errors and prior sale.