Used Kellenberger Kel-Varia Ur175-1000 Bema 12-3 for sale (80,374)

Condition: used, Year of construction: 2002, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m Photos of identical machine with centre height 225mm Base: Kellenberger Kel-Varia UR175-1000 Kelco 120 Grinding head UR with T1-T2-T3 Basic equipment: -T1 500mm grinding disc diameter -T2 400mm grinding wheel diameter -Infinitely variable, high-resolution axis -Marposs measuring device for tool measurement -Active longitudinal positioning -GAP on T1 and T2 from ELASO contactless integrated in the control interface Semi-automatic balancing from ELASO integrated into the control interface -Tailstock with manual retraction -MK5 workpiece headstock with short taper DIN 55026 Belt-driven internal grinding device Options at an extra charge: - New high-precision workhead with torque drive - Internal grinding device for high-frequency spindles diameter 120mm -HF internal grinding spindle Fischer MFM-1224/42/31 re.HJND-21 -HF spindle with HSK holder 24,000 rpm with integrated GAP sensor. (delivery time) -CNC-controlled C-axis non-circular grinding -hydrostatic threaded spindle in x -new hydrostatic unit with only 1 pump and pressure accumulator thus better energy efficiency. -monitoring of the water content in the hydrostatic system -Suction system Further options available on request Mechanical overhaul: -Complete machine overhauled according to Kellenberger measurement protocol -New service-friendly cab -repainting Electrical overhaul: -New modern CNC CIRCULAR GRINDING MACHINE control with BEMA rough grinding surface -New control cabinet -New drive technology -Replacement of all electrical cables Berus pressure switches etc. -New absolute glass scales in x and z -New absolute rotary encoder (for B-axis) Hjdpsuxfucsfx Aqgsfn Control system: The grinding software consists of a basic licence and various options that are possible depending depending on the equipment of the machine. Basic software - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal taper pendulum grinding - External and internal radius grinding, radius dressed on disc - Semi-automatic pendulum grinding - Workpiece zeroing - Grinding wheel zeroing - Measuring the dressing diamonds - 2 moulding diamonds - 1 shaped diamond or dressing roll (dressing roll required) - Moulding roller (dressing roller required) - 3 Flat dresser - Corrections - Z-position measurement (probe required) - GAP probing (grinding device required) OPTIONS at an extra charge: Software profile plunge-cut grinding: - External and internal profile plunge-cut grinding with profile disc Profile grinding software: - External and internal profile grinding with straight disc Software thread grinding: - Single and multi-start external and internal thread grinding with thread on the disc disc Dressing. Dressing of single and multi-groove discs. Flank angle freely selectable. Trapezoidal thread grinding software: - Additional dressing of trapezoidal threads possible External and internal non-circular plunge-cut grinding: - External and internal non-circular plunge-cut grinding Non-circular grinding software: A prerequisite for non-circular grinding is that the workpiece axis is equipped with a high-resolution rotary encoder so th...

Condition: used, Year of construction: 1995, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Teilüberholte Maschine mit Messprotokoll nach Neumaschinentoleranz Hfedpfx Aeyatx Ssqgon NEUE Steuerung Eckelmann ENC mit BEMA Schleifsoftware KEL-ASSIST für Kelco 90 numerisch gesteuerte B-Achse Innnschleifrinrichtung Dia 80mm Schleifscheibe links Durchmesser 400mm Schleifscheibe rechts Durchmesser 300mm Innenschleifspindel HJN 828 hydraulischer Reitstock Mikroverstellung KEL SET Messsystem

Condition: used, Year of construction: 1998, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Überholte Maschine mit Messprotokoll nach Neumaschinentoleranz NEUE Steuerung Eckelmann ENC Hodpsz Ikvgefx Aqgjfn mit BEMA Schleifsoftware Antriebe,Motoren,Maßstäbe aus Originalmaschine. Werkstückspindelstock nur umlaufend mit 320Nm numerisch gesteuerte B-Achse Innnschleifeinrichtung Dia 120mm HF-Spindel Schleifscheibe links Durchmesser 400mm Schleifscheibe rechts Durchmesser 400mm Innenschleifeinrichtung für HF Spindeln Reitstock mit Mikroverstellung KEL SET Messsystem Aktiv-Längspositionierung Kel-Pos Anschnitt-Sensor Marposs

Condition: used, Year of construction: 1999, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Control FANUC 18i-TA GENERALÜBERHOLT Foto von ähnlicher bereits gelieferter Maschine - Schleifscheibenausrüstung LINKS 500mm - Schleifscheibenausrüstung RECHTS 400mm - Innenschleifeinrichtung 120mm für riemengetriebene Innenschleifspindeln (standard) - CNC-Steuerung FANUC 18i-TA - vorbereitet für Messsteuerung Marposs kombiniert (Minialsar, Positionar)mit E5N - B-Achse - Kel-Set - hydraulischer Pinolenrückzug - Mikroverstellung am Reitstock - Werkstückspindelstock mit schwenkbarem Unterteil - Schleifscheibenausrüstung LINKS 500mm - Schleifscheibenausrüstung RECHTS 400mm - Innenschleifeinrichtung 120mm für riemengetriebene Innenschleifspindeln (standard) - CNC-Steuerung FANUC 18i-TA - vorbereitet für Messsteuerung Marposs kombiniert (Minialsar, Positionar)mit E5N - B-Achse - Kel-Set - hydraulischer Pinolenrückzug Hfjdpfxjy U N Hpe Aqgsn - Mikroverstellung am Reitstock - Werkstückspindelstock mit schwenkbarem Unterteil

Condition: used, Year of construction: 2000, grinding diameter 500 mm grinding length 1000 mm centre height 250 mm -major maintenance -New table geometry -partial painting of the interior grinding wheel equipment LEFT 400x63x127mm (standard) grinding wheel equipment RIGHT 300x40x127mm Internal grinding unit Ø120mm for HF spindles CNC control KELCO 120 C-axis for non-circular grinding. Kel-Poly B-AXIS: CNC-controlled B-axis KELCO 120: v constant 35m/s or 45m/s High-frequency internal grinding spindle Operating unit for MFV and MFZ spindles Hydraulic quill retraction for the tailstock NO micro-adjustment on the tailstock Spring-loaded quill insert Top table cooling Standard workpiece headstock MK 5 DIN 55026 size 5" Hfjdpfxsxzk Nij Aqgon Micro-adjustment for the standard workhead Dressing device on the lower table Active longitudinal positioning KELPOS, MARPOSS, mounted on the grinding head Tool measuring system KELSET, MARPOSS MARPOSS gate sensor Measuring control MARPOSS Minialsar prepared Paper belt filter

Condition: used, Year of construction: 1995, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Completely overhauled in 2013 Heavy duty workpiece headstock tailstock Without chuck and without bezel in the photo Hfodpfx Aoxyadasqgsn Kelco 90 control The machine can be viewed in operation at the customer's premises from 2025 up to and including January 2026.

Condition: used, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0-9,99 mm/Ø 0-9,99 mm/Ø ±8 ° longitudinal feed of the table 1100 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannung kg cross travel max. 270 mm 80 mm tailstock quill taper MT 3 quill travel 30 mm total power requirement 6,5 kW weight of the machine ca. 3,05 t dimensions of the machine ca. 4 x 2 m Overhauled according to Kellenberger guidelines including new, modern and future-proof control system. Photo of already delivered machine in centre distance 1000mm. -Operation via the touch panel is extremely simple. -The symbols on the control panel are practically identical to the original original control system, so there is no need for familiarisation. -Diagnostic function with display of PLC messages and digital I/O -Dressing function can be extended or changed at the customer's request. -Orientated spindle stop of the workpiece spindle possible on request. -New maximum infeed of 40 mm can be extended on request. -Digital display in 2 axes. Resolution x-axis 0.5my Options: -Encoder with digital display in the workpiece headstock -Rotary encoder with digital display in the grinding headstock (no height adjustment with spindle possible) with spindle possible) -New stable internal grinding device diameter 80mm or 100mm with height adjustment. -Increase of the centre height to max. 225mm -Speed control for the grinding spindle Included: -Operating tool -Clamping tube for chuck Further accessories on request. The x-axis of the machine has an electronically controlled infeed system with stepper motor drive. Hydraulic longitudinal and rapid traverse table movement. Versatile application in production for external cylindrical and internal internal grinding or for external, face and internal grinding in one clamping clamping of individual parts. Hedpfeuxfupjx Aqgofn Possible options: -Semi-automatic dressing cycles for external and internal grinding -automatic dressing compensation. -Measuring control

Condition: used, Year of construction: 2002, grinding diameter 350 mm grinding length 1000 mm Hodezz S Awspfx Aqgofn centre height 175 mm

Condition: used, grinding diameter 450 mm grinding length 1000 mm centre height 225 mm Fotos von bereits gelieferten Maschinen. Mechanische Überholung: -komplette Maschine nach Kellenberger Messprotokoll überholt -Neue servicefreundliche Kabine -Neulackierung Elektrische Überholung: -FANUC Steuerung mit BLUE-SOLUTION Hjdozkvucepfx Aqgsfn -Neu aufgebauter Schaltschrank -Neue Antriebstechnik -Austausch sämtlicher elektrischer Leitungen Berus Druckschalter etc. -Neue Absolut-Glasmaßstäbe in x- und z -Neuer Absolut Drehgeber (Bei-B-Achse) Fotos von bereits gelieferter Maschine mit anderen Optionen. Schleikopfvariante UR/RS: -Schleifscheibenanordnung für Aussen -und für Schrägeinstichschleifen hintereinander! -Dadurch jeweils 400mm Scheibendurchmesser! -Dadurch wesentlich geringere Kollisionsgefahr -Einfacheres programmieren -Schleifscheibenausrüstung jeweils 400x63x127mm -Einrichtung zum Betrieb einer HF-Spindel -Spindel optional gegen Aufpreis -B-Achse CNC gesteuert zum Aussen-Plan- und Innenschleifen in einer Aufspannung. Schwenkbereich +10°/-270° -C-Achse zum Polygonschleifen -Unterteil fest -Schleifkopfmotor 10,0 KW -Reitstock -Marposs Messsystem zur Schleifscheibenvermessung. -Längspositionierung Marposs

Condition: used, Year of construction: 2003, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Sehr gut erhaltene Kel-Vista Steuerung FANUC 21i Maschine erhält Wartung und Geometrie nach Kellenberger Messprotokoll. -B-Achse automatisch 2,5° -T1 Schleifscheibendurchmesser 400mm -T2 Schleifscheibendurchmesser 300mm -T3 Innenschleifeinrichtung riemengetrieben -Reitstock mit Mikroverstellung -pneumatische Entlastung Obertisch -Sinuslineal -Aktive Längspositionierung Kel-Pos -GAP Anschnitt Sensor -Messsteuerung Movomatic Hfjdpfx Aqjz Rkbisgon -Papierbandfilter

Condition: used, KELLENBERGER KEL‑VISTA UR 175/1000 is a CNC cylindrical grinder, engineered for precision, high accuracy and reliability. Capacities: centre height 175 mm, distance between centres 1000 mm, max workpiece 100 kg; grinding wheel Ø400×63 mm, bore 127 mm; tailstock travel 50 mm, max table tilt 9°. Specs: wheel peripheral speed 35 m/s, spindle speeds 8–800 t/min (stepless), grinding spindle motor 5 kW, rapid feed 12 m/min, spindle taper ASA5/MK5, overall L3200×W1700×H2000 mm. Accessories: coolant system, paper filtration, set of grinding wheels. Delivers tight tolerances; ideal for automotive, aerospace, machine tools and medical sectors. Hedpez Dvzajfx Aqgsfn

Year of construction: 2004, condition: ready for operation (used), travel distance X-axis: 320 mm, travel distance Z-axis: 1,150 mm, controller manufacturer: HEIDENHAIN, overall weight: 6,000 kg, This KELLENBERGER KEL VARIA RS 175/1000 Grinding machine was manufactured in the year 2004 in Switzerland. It is equipped with a HEIDENHAIN control unit. Machine Benefits Qualitative Machine Benefits • Good condition Technical Machine Benefits • Distance between centres: 1000 mm • Centre height: 175 mm Hedpfxeyi Elie Aqgofn • Grinding wheel dimensions right Ø 400 x 50 mm • Grinding wheel head movements -210°/+30° • Rotational speed 8-800 rpm • Spindle type cm5

Condition: used, Year of construction: 2006, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm weight of the machine ca. 3,5 t Machine completely overhauled with 12 months warranty Mechanically and optically like new Hfodpfjt Ii Nbex Aqgsn Photos from the last overhauled machine with different options Fanuc 21i control -Grinding head UR 1-2-3 external/internal/plan -Axis automatic 1° Hirth serration -Active longitudinal positioning KEL-POS Movomatic -Semi-automatic balancing device KEL-BALANCE -Grinding wheel equipment left 400mm diameter -Grinding wheel equipment right 300mm diameter -Internal grinding unit with belt drive -Tailstock with micro-adjustment -fine adjustment upper table -Paper belt filter SBP4 240l

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and Hsdpouxfu Nefx Aqgsfn maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: used, KELLENBERGER KEL-VARIA R175 x 1500 is a CNC cylindrical grinder engineered for high precision, top accuracy and reliable production. Capacities: centre height 175 mm, distance between centres 1500 mm, Z-axis 1650 mm, workpiece weight on centres max. 150 kg; grinding wheel Ø500×80 mm (bore 203 mm) or Ø400×63 mm (bore 127 mm); max wheel travel 320 mm. Key specs: wheel speeds stepless 1000–2150 rpm (peripheral speed 45 m/s); feed 7500 mm/min; work spindle swivels -10/+100° with 8–800 rpm; permitted load 160 Nm; grinding spindle motor 7.5 kW; work spindle motor 2 kW; 3×400 V 50 Hz; rapid 15 m/min; approx. weight 6000 kg; dimensions 4700×2300×2000 mm; air 6 bar. Accessories: coolant system, paper filtration, MARPOSS touch probe, set of grinding wheels, rotary centre, set of centers, set of workpiece drivers, set of throat gauges, lamp, 2 tool cabinets, tailstock with fine adjustment, oil mist extractor, spindle nose for collets. Achieves tight tolerances; typical applications: automotive, watchmaking, machine tool Hfodsyxn Itspfx Aqgsn

Year of construction: 2015, condition: excellent (used), On behalf of a client from Switzerland, I am offering this machine for sale. Hfsdpegtingefx Aqgon It has 5,200 operating hours and is in excellent condition. Used for prototype construction, currently in operational condition. Equipped with: Grinding head UR T1 500 x 80; T2 400 x 63 1 internal spindle HF MFM 1224/42 1 internal spindle HF MFM 1290 Semi-automatic balancing device KEL-TOUCH on the workpiece spindle head for internal and external grinding KELSET grinding wheel measuring system KELPOS longitudinal positioning Heidenhain CNC GrindPus 640 CNC B-axis, hydrostatic CNC C-axis for polygon and thread grinding KELSOFT NCG for non-circular grinding KELTHREAD for thread grinding KELREMOTE for remote diagnostics Prepared for measuring controls Paper band filter Streuli 480 l Extraction system Available for immediate delivery from Switzerland.

Condition: used, TECHNICAL DETAILS - centers height : 125 [mm] - max grinding length : 430 [mm] - max part diameter : 249 [mm] - max part weight : 100 [kg] - grinding wheel size : Ø400 x 63 x 127 [mm] - part holder headstock spindle speed : 8 - 800 [rpm] - max stroke X, Z : 320 , 650 [mm] - floor space : 2500 x 2000 [mm] - weight : 4700 [kg] Hfsdpfx Asy Tb Aaoqgon EQUIPMENT - CN FANUC 18iTA - tailstock with fine adjustment - grinding head type URS - grinding head orientation each 0.1 degrees - inside grinding device with spindles Ø120 mm FISCHER type MFZ-1090 90000 Rpm and et type MFV-1230 12000-30000 Rpm - various grinding wheel flanges - grinding wheel extractor - 2 diamond dressing devices for inside and external grinding wheels - active flagging device MARPOSS Kel-pos - tool-measuring system Kel-set - Kel set system - 3 jaws chuck

Condition: used, Year of construction: 1997, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm weight of the machine ca. 6 t Verkauf erfolgt mit Funktionsprüfung Auf Wunsch mit neuer Tischgeometrie gegen Aufpreis C-Achse zum Polygonschleifen B-Achse mit Handschwenkung Schleifscheibendurchmesser links 400mm Schleifscheibendurchmesser rechts auf Anfrage Hfedpfjy R Ed Nox Aqgsn Innenschleifeinrichtung Reitstock mit Feinverstellung

Condition: used, Year of construction: 1995, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Control Kelco 90 weight of the machine ca. 6 t Verkauf erfolgt mit Funktionsprüfung Auf Wunsch mit neuer Tischgeometrie gegen Aufpreis B-Achse stufenlos Schleifscheibendurchmesser links und rechts 400mm Innenschleifeinrichtung Hfedpfxsy R Ed Ao Aqgon Reitstock mit Feinverstellung Sinuslineal am WSS Kel-Set Passive Längspositionierung Movomatic TMP91

Condition: used, KELLENBERGER KEL‑VARIA R175 x 1500 is a CNC cylindrical grinder engineered for precision, high accuracy and reliable operation. Capacity: centre height 175 mm, distance between centres 1500 mm, Z 1650 mm, max 150 kg; wheels Ø500×80 mm (Ø400×63 mm option). Specs: wheel speeds 1000–2150 rpm, peripheral 45 m/s, max travel 320 mm, feed 7500 mm/min, motors 7.5/2 kW, rapid 15 m/min, 3×400 V, weight ≈6000 kg, dims 4700×2300×2000 mm. Equipment: paper/coolant filtration, MOVOMATIC, Renishaw LP2H probe, wheel flange extractor, remote hand control, MPM balancing. Achieves tight tolerances; suited to automotive, watchmaking, machine tools, aerospace and medical. Hedeyxn A Repfx Aqgsfn

Condition: used, grinding diameter 350 mm grinding length 1500 mm centre height 175 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0-40 mm/Ø 0-40 mm/Ø ±6,5 ° longitudinal feed of the table 1530 mm table speeds 0,02-6 m/min 130 kg cross travel max. 270 mm 130 inkl. Spannung kg 80 mm tailstock quill taper MT 3 quill travel 30 mm total power requirement 6,5 kW weight of the machine ca. 3,05 t dimensions of the machine ca. 4 x 2 m Overhauled according to Kellenberger guidelines including new, modern and future-proof control system. Photo of machine already delivered with special options -Operation via the touch panel is extremely simple. -The symbols on the control panel are practically identical to the original original control system, so there is no need for familiarisation. -Diagnostic function with display of PLC messages and digital I/O -Dressing function can be extended or changed at the customer's request. -Orientated spindle stop of the workpiece spindle possible on request. -New maximum infeed of 40 mm can be extended on request. -Digital display in 2 axes. Resolution x-axis 0.5my Options: -Encoder with digital display in the workpiece headstock -Rotary encoder with digital display in the grinding headstock (no height adjustment with spindle possible) with spindle possible) -New stable internal grinding device diameter 80mm or 100mm with height adjustment. -Increase of the centre height to max. 225mm -Speed control for the grinding spindle Included: -Operating tool -Clamping tube for chuck Further accessories on request. The x-axis of the machine has an electronically controlled infeed system with stepper motor drive. Hsdpfx Aeuxftrsqgofn Hydraulic longitudinal and rapid traverse table movement. Versatile application in production for external cylindrical and internal internal grinding or for external, face and internal grinding in one clamping clamping of individual parts. Possible options: -Semi-automatic dressing cycles for external and internal grinding -automatic dressing compensation. -Measuring control

Condition: used, Distance between centres: 1000 mm Centre height: 250 mm B-axis: Accuracy 0.1" CNC brand: Kelco CNC model: 90 Left grinding wheel dimensions (OD x ID x width): Ø400 x Ø127 x 63 mm Right grinding wheel dimensions (OD x ID x width): Ø400 x Ø127 x 50 mm Workhead swivel: -30º to +120º Workhead taper: MK 5 Hsdpfx Aqoxmg Ekogofn Max. workpiece weight between centres: 150 kg Tailstock taper: MK 4 Tailstock quill travel: 50 mm Maximum peripheral speed: 32 m/s High-frequency internal grinding spindle: Ø120 mm High-frequency internal grinding spindle brand: WARNER model K 3.000 Main motor power: 7.5 kW Total power: 26.5 kW Max. Z-axis travel: 1,150 mm Max. Z-axis feed speed: 15 m/min Worktable rotation: 0º to 9º Max. X-axis travel: 320 mm Max. X-axis feed speed: 7.5 m/min Length: 3,600 mm Width: 2,000 mm Approx. weight: 5,000 kg

Condition: used, grinding diameter 350 mm grinding length 600 mm centre height 175 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0-9,99 mm/Ø 0-9,99 mm/Ø ±10 ° longitudinal feed of the table 1100 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannung kg cross travel max. 270 mm 80 mm tailstock quill taper MT 3 quill travel 30 mm total power requirement 6,5 kW weight of the machine ca. 3,05 t dimensions of the machine ca. 4 x 2 m Overhauled according to Kellenberger guidelines including Hfjdpfx Ajuxft Ejqgon new, modern and future-proof control system. Photo of already delivered machine in centre distance 1000mm. -Operation via the touch panel is extremely simple. -The symbols on the control panel are practically identical to the original original control system, so there is no need for familiarisation. -Diagnostic function with display of PLC messages and digital I/O -Dressing function can be extended or changed at the customer's request. -Orientated spindle stop of the workpiece spindle possible on request. -New maximum infeed of 40 mm can be extended on request. -Digital display in 2 axes. Resolution x-axis 0.5my Options: -Encoder with digital display in the workpiece headstock -Rotary encoder with digital display in the grinding headstock (no height adjustment with spindle possible) with spindle possible) -New stable internal grinding device diameter 80mm or 100mm with height adjustment. -Increase of the centre height to max. 225mm -Speed control for the grinding spindle Included: -Operating tool -Clamping tube for chuck Further accessories on request. The x-axis of the machine has an electronically controlled infeed system with stepper motor drive. Hydraulic longitudinal and rapid traverse table movement. Versatile application in production for external cylindrical and internal internal grinding or for external, face and internal grinding in one clamping clamping of individual parts. Possible options: -Semi-automatic dressing cycles for external and internal grinding -automatic dressing compensation. -Measuring control

Condition: good (used), Distance between centers: 760 mm Maximum travel on the Z axis: 650 mm Maximum grinding length: 430 mm Maximum grinding diameter: 250 mm Height of centers: 125 mm Maximum grinding wheel diameter: 500 mm Maximum travel on the X axis: 320 mm CNC brand: FANUC CNC model: 18TB Main motor power: 7.5 kW Z and X axis resolution: 0.1 µmm Hsdpsv Tmtlofx Aqgjfn Workhead taper: MORSE 5 Workhead hole diameter: 38 mm Tailstock taper: MORSE 4 Workhead rotation speed: 8 to 800 rpm Dimensions (length x width): 2500 x 2000 mm Weight: 4700 kg

Condition: used, Year of construction: 1977, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm Hfedeynmpgspfx Aqgjn MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m Neu geliefert an Universität. 2018 übernommen. Dann komplett bei BEMA gewartet und an an Einmannbetrieb geliefert. Nun wird die Maschine nochmal gewartet und Tischgeometrie neu hergestellt. 2-Achsen-Digitalanzeige Fagor nachgerüstet. -Reitstock mit Feinverstellung -Innenschleifeinrichtung -Kühlmittelanlage Zubehör auf Anfrage