Frase

Martin

Condition: used, Year of construction: 2006, Used Machine Year of Manufacture: 2006 Features and Technical Specifications - Motor power: 4 kW/400 V - Saw blade swivels on both sides from -46° to 46°—a total swivel range of 92° for flexible angle cuts against the rip fence and crosscut fence - Maximum cutting height: 72 mm - Saw blade diameter: 250–315 mm - Saw blade speed: 5,000 rpm - Cutting width: 1,250 mm - Sliding table length: 3,300 mm - Touchscreen control with an eye-level control panel - Electric height and tilt adjustment of the saw blade - Intuitive operating menus with step-by-step guidance for complex operations - Integrated calculator and special functions for angle cuts and chamfering - Tool management for up to ten tools, enabling dimensionally accurate setup without the need for re-referencing after a saw blade change Ksdpfx Ahe Advffjaenc - Keyless “VLock” quick-change saw blade system for fast tool changes - Precision sliding table with interchangeable table lip and sturdy hollow-section profiles, lockable in any position - Ball-bearing-mounted rip fence with adjustment via handwheel and digital display - Length stop with smooth-running stop carriage and fine adjustment - Splitting wedge guard for a clear view of the saw blade and workpiece - Dust extraction port on machine stand: 120 mm - Dust extraction port on guard: 60 mm - T74 parallelogram cross table - DIN A4 guide holder - T74 length stop, similar to the above, with continuous stop surface and two hinged stop elements - CE standard - Weight: approx. 1,250 kg

Condition: used, Year of construction: 2026, New demonstration machine! General technical features: - Control: 7.0" touchscreen ConnectTouch control - Cutting height and cutting angle electronically controlled, digital input of cutting height and angle (controlled positioning of the motorized axes) and movement of the motorized axes in hold mode (axis movement via push button); display resolution: 0.1 mm or 0.01°; repeat accuracy ± 0.05 mm or ± 0.005° - Weight: approx. 1,600 - 2,200 kg - Table size: 860 mm x 1,270 mm in gray cast iron, table extension as standard across the entire table width - Table height: 900 mm - Stand: The machine stand is a stable, thick-walled composite structure, implemented in this form and perfection exclusively by MARTIN. The intelligent combination of the two materials, steel and concrete, creates a high-quality stand that is unsurpassed in terms of stability, damping capacity and torsional stiffness. - Tools: Diameter 250 - 450 mm, optionally up to 550 mm, main saw blade ø 30 mm with additional holes, scoring saw ø 36 mm, tool cutting width max. 20.0 mm for machines with single-sided tilting, 6 mm for machines with double-sided tilting; saw blades up to 350 mm can be lowered under the table. Special tool diameter max. 400 mm, weight max. 12.0 kg - Tool change: Quick-change system ProLock - Tool tilt: 0° to + 47°, tilting only possible with saw blades up to 6 mm cutting width - Cutting height: 0°: max. 155 mm / saw blade ø 450 mm; T7710/1: +45°: 106 mm / ø 450 mm; T7710/2: +45°: 104 mm / ø 450 mm; -45°: 88 mm / ø 450 mm; optionally 123 mm / ø 550 mm - Motor: State-of-the-art synchronous motor SynchroDrive with large power reserves in energy efficiency class IE4 - Motor power: 5.5 kW, due to its design, the motor can be overloaded several times its rated power for a short period of time and thus offers large power reserves - Speed: Continuously variable 1,000 - 5,000 rpm - Control panel: The control panel is at eye level and is rotatably mounted around its vertical axis. In addition, it can be swiveled to the right, so that larger components can also be processed easily - Rip fence: Standard length 3,000 mm, table length corresponds to cutting length; position-independent locking; guides hardened, wear-resistant, self-cleaning; table edge replaceable; made of anodized aluminum - Length stop: Made of anodized aluminum with continuous support, fine adjustment for both flap stop elements; dimension display via scale with magnifying glass; cutting length 95 - 2000 mm, extendable up to 3220 mm - Cross table: Made of powder-coated steel, workpiece support in anodized aluminum, two sliding supports for extending the support area; length stop can be placed in the front and rear position without lifting; one-hand clamping on the support surface 1340 x 650 mm - Surfaces: Stand: Stand with high-quality powder coating, Cast iron: Table surface finely milled, Aluminum: Aluminum components anodized - Protective cover / extraction: Height-adjustable protective cover incl. interchangeable rear part for miter cuts; protective cover for saw blades up to ø 450 mm (optionally 550 mm); extraction connection on the cover: Ø 80 mm, on the machine stand Ø 120 mm; total extraction connection Ø 140 mm; minimum air volume: Vmin 18.5 m3/min at 20 m/s, negative pressure 1,400 Pa - Electrical equipment: Contact for controlling the extraction; motor protection switch and winding protection, undervoltage protection; lockable main switch, 2 EMERGENCY STOP buttons (control panel, stand) Knedpfx Ahsz A Hh Usaoc

Condition: used, Year of construction: 1991,

Condition: used,

Condition: used, Year of construction: 1975, Technical details: turning diameter over bed: 400 mm turning diameter over support: 220 mm Kodpfeu Ix E Hox Ahaenc turning length: 1100 mm centre height: 180 mm spindle passage: Ø 45 mm range of revolution per miute: 31,5 - 1.400 / 12 step U/min range of feed in x - axis: längs: 0,08 - 1,10 m/min range of feed in y - axis: quer: 0,028 - 0,40 m/min tailstock quill taper MT: MK4 tailstock quill adjustment: 200 mm total power requirement: 4,0 kW weight of the machine ca.: 1,7 t dimension machine xH: 2,5 x 1,1 x 1,4 m Equipment: -Three-jaw chuck Ø 250mm manufacturer Forkardt with interchangeable jaws -Multifix steel holder -Cooling water device with pump -chuck guard -chip collecting tray -chip guard Accessories: -chuck spanner -tool holder -2 pieces gears *

Condition: used, Year of construction: 1994, functionality: fully functional, Martin swivel spindle milling machine T25 with accessories Knedpe Aaz H Tjfx Ahasc Functional Location: Freising Inspection is welcome. We have other used machines available. Please contact us.

Condition: excellent (used), Year of construction: 2008, Control panel, suspended, swiveling, and with template holder 5.7″ touchscreen control Variable saw blade speed 2-axis scoring unit, electrically adjustable Parallelogram crosscut table with “RadioCompense” angle cut and length compensation system Pre-set indexing points for 0°, 22.5°, 30°, 45° on the parallelogram crosscut table Rip fence with stop flap and digital dimension display Extendable parallelogram crosscut table with support roller Parallel stop can be lowered under the table in the end position Table extension 600 x 400 mm with integrated storage compartment “ProLock” quick-change system for saw blade Central lubrication including miter stop for cutting acute angles Sliding table length: 3300 mm Cutting width: 1100 mm Cutting width with rip fence: 3400 mm Cutting height: 170 mm Saw blade diameter max.: 500 mm (400 mm with scoring unit) Saw blade speeds: 2000 - 6000 rpm Saw blade tilt: 0 – 46° Kodpfxs Aaz E As Ahaonc Motor power: 7.5 kW, 400 V, 50 Hz Working height: 900 mm Dust extraction connection: 80 and 120 mm Transport dimensions approx. L x W x H: 3550 x 1850 x 1620 mm Weight approx.: 1800 kg

Condition: used, Year of construction: 2000, Motor: 7.5 kW Tersa cutterhead, Z = sliding rollers in the thickness table, height-adjustable, steel feed roller, ribbed, infeed roller before and after the thickness table, safety bar. Cutterhead speed: 5000 rpm. Planing height: 2.8 - 250 mm with digital display. Planing width: 630 mm. Max. chip removal: 8 mm. Dust extraction port: 160 mm. Weight: approx. 1115 kg. Dimensions: 1140 x 1260 x 1200 mm. Location: Supplier. Ksdpfxe Aay D Rs Ahaenc

Condition: used, Year of construction: 2000, Working width: 500 mm Knsdpj Aay D Djfx Ahaoc Motor: 5.5 kW with motor brake Tersa cutterblock, Z=2 Speed: 5,000 rpm max. Maximum chip removal: 8 mm Adjustable planer table with motorized height adjustment Angled fence with integrated auxiliary fence Suvamatic cutter guard Weight: approx. 1000 kg Dimensions: 2850 x 850 x 1110 mm Location: Supplier

Condition: excellent (used), Electrode clamp with air connection for electrode tool, electrode welding machine, joint planer, joint planer Kedpfx Aex E N Uzshajnc -Manufacturer: Kurt Haufe, Joint Planer Type K 12 B 600 -Cable length: 3 m -hollow cable -Number: 1x joint planers available -Price: per piece -Transport dimensions: Ø 450 x 90 mm -Weight: 3.2 kg/pc.