Cut-to-length-lines

SCHLEICHER

Condition: good (used), Baling press, Schleicher, 16 S – used - : Ex-works price: only €1,950 (net) Manufacturer: Schleicher Model: 16 S Serial number: 6150I1730E Iodpfx Aeyzcwhjpcear Year of manufacture: 20 Height: 2000mm / Width: 1500mm / Depth: 900mm Weight: 1,850kg 380V, 3-phase, 10.3 AMP, 4kW Condition: good Available: immediately Location: Husum Operating manual not available.

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Iedpewp Rqfsfx Apcear Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: used, Year of construction: 1988, Strip feed line for sheet metal coils with decoiler and integrated feeder unit. Manufacturer: H. Schleicher GmbH & Co. Model: RMS 8-70/160-650 Model: HE-200-900 Spz Year of manufacture: 1988 Strip width: 100 – 600 mm Iedpfx Apoyyn Icecjar Strip thickness: 0.5 – 3 mm Max. load: 11 t Voltage: 24 / 380 V Frequency: 50 Hz Power: 5 kW

Condition: ready for operation (used), Year of construction: 1979, functionality: fully functional, compressed air connection: 5 bar, From business closure Schleicher dowel drilling machine DBS 1000 Year of manufacture: 1979 Also ideal for line boring with 5mm holes, 32mm spacing Comes with 25 pcs. 5mm carbide-tipped brad point drills and 8mm carbide drills, as well as 16mm and 35mm drill bits for cup hinges and other drill bits Pneumatically tiltable to horizontal/vertical position Machine is mobile Payment in cash upon collection Ijdpfx Aex Avf Sjpcsar No warranty

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Isdpfsfz U S Eex Apcear Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Condition: used, Year of construction: 1998, material width 100 - 450 mm material thickness 1,0 - 14,0 mm coil weight 10,0 t coil internal diameter 470 - 520 mm coil external diameter 1100 - 2000 mm no. of straightening rolls 12 straightening roll diameter 2x70 / 2x96 / 8x127 mm number of draw-in rolls 2 inlet roll diameter 160 mm min. material width 100 mm speed 15 m/min power requirement 75,0 kW Iaedevuugiepfx Apcsr weight of decoiler 6,4 t weight of straightening machine 12,8 t dimensions decoiler (WxDxH) 3,1 x 1,4 x 3,7 mm dimensions straightener (WxDxH) 2,5 x 3,4 x 2,7 mm Straightening machine RMS Vario-12-70/96/127-450 with infinitely variable drive, driven straightening rolls, supporting rolls, upper straightening cassette hydraulic liftable, hydraulic threading wedge Decoiler HES 12-650 with infinitely varieble insertion drive, pneumatic lag brake, hydraulic snubber roll (motoric driven), hydraulic centralized expansion hydraulic coil lifting device hydraulic loop bridge coil loop control via ultrasonic cropping shears HSO 150-0450 working direction from left to right as is where is, WITHOUT putting into operation - Video at seller's site before dismantling available

Condition: used, Year of construction: 1971, material width 300 mm coil weight 2,0 t material thickness 1,0 - 5,0 mm coil internal diameter 440 - 520 mm coil external diameter 1320 mm no. of straightening rolls 6 straightening roll diameter 70 mm number of draw-in rolls 2 diameter of draw-in rolls 70 mm power requirement 1,1 kW weight of decoiler 2,0 t dimensions decoiler (WxDxH) 2,0 x 2,0 x 1,7 mm weight of straightening machine 1,3 t dimensions straightener (WxDxH) 2,7 x 1,3 x 2,4 mm Iasdpfx Aevut Dtepcor Straightening machine RM-S 300 with infinitely variable drive, pneumatic intermittent lifting, hydraulic inlet table, bending roll, alligator opening, coil loop control Decoiler H 2 with auxiliary drive, pneumatic snubber roll, hydraulic expansion, manually shiftable as is where is, WITHOUT putting into operation Price for commissioning (in given condition) on request

Condition: ready for operation (used), Year of construction: 2002, There are zwei identical vertical bag filling machines available, weight: 1.1t. Iodonfvxzspfx Apcear

Condition: used, sheet width 400 mm plate thickness 3 mm Iaodoyq Sx Eopfx Apcer stations . System with the best coiler, straightener, eccentric press, and profile rolling machine Cutting-off system and numerous accessories Iron double coiler Type SFD 2000 Schleicher straightener Edelhoff AZR 3/100 eccentric press Press force 100 t Stroke adjustment 20-110 mm Ram adjustment 100 mm Ram strokes 105 /min The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Year of construction: 1983, material width 200 mm material thickness 0,8 - 3,0 mm Iaedpfjvuk R Rex Apcsr no. of straightening rolls 6 straightening roll diameter 53 mm number of draw-in rolls 2 diameter of draw-in rolls 96 mm material cross-cut 400 mm² speed 3 - 15 m/min power capacity 0,75 kW weight 0,5 t Dimensions (WxDxH) 1,0 x 1,0 x 1,4 m SPECIAL DEAL as is where is, WITHOUT additional work free loaded to truck

Condition: ready for operation (used), Including Ascending Conveyor SBM 45 and Counting Machine ZMR 3/ 3-130. Iedpohncwisfx Apcear

Condition: used, Year of construction: 1973, material width 650 mm coil weight 2,0 t coil internal dia. 380 - 520 mm coil outside dia. 1500 mm speed 20 m/min Power capacity 2,0 kW Iajdpeymp Szjfx Apcor Weight 1,4 t Dimensions (WxDxH) 1,6 x 1,6 x 1,6 m decoiler H 2 with motor, hydraulic expansion, hydraulic snubber roll, coil loop control

Condition: good (used), Position processor, SLAVE CPU POSITIONING -Manufacturer: SCHLEICHER, 2-axis positioning assembly Iaodpfx Asymltbepcjr -Type: USP21 -No.: 31506913-310 -Number: 2 modules available -Price: per piece -Dimensions: 150/35/H200 mm -Weight: 0.6 kg/pc.

Year of construction: 1979, condition: good (used), Underfloor circular saw, crosscut saw, pull saw, miter saw, panel saw, table saw, aluminum circular saw, panel saw -Manufacturer: Martin, panel saw type T 70 with automatic feed Iedpfxshfufge Apcoar -Engine power: 11 kW -Speed: 1445 rpm -Saw blade: Ø 410 x 5 mm -max. Cutting height: 90° 140 mm / 45° 110 mm -Miter cut: up to 45° -Sliding table: 355 x 1500 mm -Dimensions total 2275/2010/H1400 mm -Weight: 1058 kg

Year of construction: 1993, condition: ready for operation (used), A complete cutting line for sheet metal processing is available. 1) Decoiler Schleicher H-B4-1250, year of manufacture: 1983, power: 11kW, max. load capacity: 12500kg, strip thickness range: 0.5mm-1.25mm, max. strip width: 1100mm. 2) Straightening machine Schleicher RM 8-53/160, year of construction: 1980, power: 7.68kW, strip thickness range: 0.5mm-1.25mm, strip width range: 300mm-1000mm. 3) Trimming shears. 4) HSK HSKW/SF shears, year of manufacture: 1993, max. strip thickness: 1.5mm, max. material width: 1280mm. 5) Stacking line Schleicher, year of manufacture: 1980, max. load capacity: 1000kg, strip width range: 300mm-1000mm, strip thickness range: 0.5mm-1.25mm, feed length range: 200mm-1250mm, power: 1.5kW. On-site inspection is possible. Iaodpjw Az Rpefx Apcjr