Swiss-type cnc lathe

TORNOS DECO 10

Condition: used, Year of construction: 2016, Tornos Evo Deco 32/10 Sliding Head Lathe, Twin Spindle 10 Linear Axes & 2 x C Axis, Spindle 1, 5C Spindle 32mm Max Bar Diameter, Serviced by 6 Turning Tool Positions, 4 Drill/Mill End Bar Positions, All Drive Capable, 6 Side Mill/Drill Postions, 4 Drive Capable, Spindle 2 - Subspindle, ER Collet Type, Serviced by 3 Turning Tool Positions, 4 Mill/Drill End Bar Positions, All Drive Capable, Parts Grabber and Parts Hatch, 8000rpm on Main & Sub, Fanuc 31i-BS CNC Control, 240mm Max Work Piece Length, Tornos Robobar SBF-532 Bar Feed, 3 Metre Bar Length Max, 820kg. S/No. 13366 (2016) 3800kg. Country of Origin: Switzerland Ffsdpfx Aajytf U Semow Location: These lots are located in Kent, UK. Unfortunately there are no loading facilities on-site, dismantling and loading will be at the cost of the Purchaser. All/Any tooling is being offered as specifically described.

Condition: ready for operation (used), Year of construction: 2006, bar diameter (max.): 10 mm, controller manufacturer: FANUC, controller model: 16i-TB, number of axes: 9, Swiss type turning machine manufactured in 2006. This TORNOS DECO 10a features an automatic and integrated bar loader with a maximum bar length of 3.2 m and a bar capacity ranging from 2 to 10 mm. It includes a Robobar SSF 3m loading magazine and is equipped with a FANUC 16i-TB control system. If you are looking to get high-quality turning capabilities, consider the TORNOS DECO 10a machine we have for sale. Contact us for further details. • Overhauled in 2016: • Checked machine, ball screws (replaced if necessary), guides, guide bushing, main and counter spindles • Complete cleaning • Maintenance carried out in accordance with Block 3 • Replacement of all drive belts • Barriers, relays, filter mats replaced • Reference points adjusted • Configuration/features: • Moving headstock • Directed spindle stop (S1) • Independent counter spindle (S4) • 9 axes with C1 and C4 and Transmit • 1 cross slide with 4 tool holders • Sensor for tool breakage detection Additional equipment Fsdpfx Aeytcaloamsfw • Automatic and integrated bar loader (oil bath) TORNOS-BECHLER Type SSF-210, equipped with Robobar SSF 3 m loading magazine • Max. bar length: 3.2 m • Bar capacity: min. 2 mm, max. 10 mm • Max. diameter without bar preparation: 8 mm (without clamp) • “HYBRIDE 10+5” drum with: • 14 guide holes for 1–4 mm • 14 guide holes for 4.1–10 mm • Loading magazine with drum • Integrated 25 L hydraulic unit with filter • Front/rear support foot, center height 1100 mm • Electrical control box (diagram 112.20.300) • Motor voltage 400 V, control voltage 24 V • Color: Anthracite RAL 7016 / Gray RAL 7035 Technical Specification Counter Spindle Yes

Condition: ready for operation (used), Year of construction: 2000, bar diameter (max.): 7 mm, number of axes: 9, Swiss type turning machine manufactured in 2000. This TORNOS Deco 10a features a movable headstock, independent counter spindle, and a pivoting workpiece holder. It includes a loading magazine with a drum and a lubrication device for guide bushing. If you are looking to get high-quality turning capabilities, consider the TORNOS Deco 10a machine we have for sale. Contact us for further details. • Movable headstock • Directional spindle stop S1 • Cross slide with 4 tool holders T11–T24 with vertical and horizontal movement • Independent counter spindle • Pivoting workpiece holder on the counter spindle • Lubrication device for guide bushing with filter • Motorization S2 • Integrated 25-liter hydraulic unit with filter • Electrical control box • Motor voltage 400 V Ffjdpfxsyr Nflj Aamow • Control voltage 24 V • Drive motor n = 12,000 rpm Additional equipment • Loading magazine with drum (bar feeder) • “HYBRIDE 10+5” drum with 14 guide tubes for 1–4 mm bars and 14 guide tubes for 4.1–10 mm bars (no bar preparation up to 8 mm) • 3 pre-settable turning tool holders • 4 fixed tool holders • Tapping attachment for collet chuck ESX 12 • Front/rear support foot, center height 1100 mm Technical Specification Counter Spindle No

Condition: ready for operation (used), Year of construction: 2006, controller manufacturer: FANUC, controller model: 16i-TB, This TORNOS DECO 10a was manufactured in 2006. It features an integrated bar loader with a maximum bar length of 3.2 m and a bar capacity ranging from 2 to 10 mm. The machine includes a Robobar SSF 3m loading magazine and a FANUC 16i-TB control system, ensuring precise and efficient operations. Ideal for intricate Swiss-type turning tasks. Contact us for more information about this machine. 2 similar machines available! Ffedpfox D Dlisx Aamow Additional information • Maximum bar length: 3200 mm • Bar capacity: Minimum 2 mm, Maximum 10 mm • Max diameter without preparation: 8 mm (without clamp) • Motor voltage: 400 V • Control voltage: 24 V • Independent counter spindle (S4) • FANUC 16i-TB control system • 1 cross slide with 4 tool holders • Sensor for tool breakage detection • Center height: 1100 mm • Automatic and integrated bar loader with oil bath • Robobar SSF 3m loading magazine • Front/rear support foot • "HYBRIDE 10+5" drum with 14 guide holes for 1-4 mm and 14 guide holes for bars 4.1-10 mm without bar preparation up to 8 mm • Electrical control box • Integrated 25-liter hydraulic unit with filter • Moving headstock • Directed spindle stopOptional: Comprehensive package of measuring instruments

Condition: ready for operation (used), Year of construction: 1999, bar diameter (max.): 10 mm, number of axes: 9, This TORNOS DECO 2000-10 was manufactured in 1999. It features a loading magazine with drum, integrated hydraulic unit, and supports both front and rear with a center height of 1100 mm. It includes a movable headstock, directional spindle stop, and cross slide with tool holders. Ideal for precision turning, it operates on AC drive motors with an absolute measuring system. Contact us for more information about this machine. 2017 overhauled and two further similar machines available (both overhauled 2018)Overhaul of 2017 machine:Standard overhaul package: Maintenance of Block III, cleaning, and recommissioning. Overhaul of the guide bushing and spindle overhaul of S1, S2, and S4. Replacement of all ball screws including bearings and the guides of all axes. Replacement of the cooling lubricant pump, all cooling lubricant lines, and the cooling lubricant sensor. Replacement of the scraper blades on the cross slides. Replacement of all pneumatic lines and valves. Replacement of the machine room light, transparent panels, external fan, fan cable, and keyboard. Additional options (special services): The guide bushing was completely replaced (not just overhauled). Installation of a new central lubrication system. Replacement of the bellows coupling, external encoders, and screen. Replacement of the control and amplifier fans. During commissioning, the “Spindle Positioning S4” option was also activated and the loading magazine was set up. Additional information • Maximum bar length: 3040 mm • Electrical control box • AC drive motors • Motor voltage: 3 x 380 V 50/60 Hz • Control voltage: 1 x 24 V DC • Movable headstock • Cross slide with 4 tool holders T11-T14 with vertical and horizontal movement • Absolute measuring system • 9 axes with C1 and C4 • Loading magazine with drum "HYBRIDE 10+5" • 14 guide tubes for 1-4 mm bars • 14 guide tubes for 4.1-10 mm bars without bar preparation up to 8 mm • Collet for Tryton • 2 different hybrid drums • Directional spindle stop S1 Fjdpfxox D D Ikj Aamofw • Equipment to be equipped with Robobar SSF 3 m loading magazine Technical Specification Counter Spindle Yes

Condition: ready for operation (used), Year of construction: 2010, bar diameter (max.): 10 mm, number of axes: 9, This TORNOS DECO 10a was manufactured in 2010. It features a movable headstock, directional spindle stop, and cross slides with tool holders. It includes an independent counter spindle, a pivoting workpiece holder, and a lubrication device. The machine also comes with a loading magazine, integrated hydraulic unit, and an electrical control box. If you are looking to get high-quality turning capabilities consider the TORNOS DECO 10a machine we have for sale. Contact us for more information. Additional information • Cross slide with 4 tool holders T11-T24 with vertical and horizontal movement • 3 pre-settable turning tool holders • 4 fixed tool holders • Movable headstock • Directional spindle stop S1 • Independent counter spindle • Pivoting workpiece holder on the counter spindle • Lubrication device for guide bushing with filter Fsdpfx Aasx D Dmtjmjfw • Tapping attachment for collet chuck ESX 12 • Loading magazine with drum • Integrated 25-liter hydraulic unit with filter • Front/rear support foot, center height 1100 mm • "HYBRIDE 10+5" drum with 14 guide tubes for 1-4 mm bars and 14 guide tubes for 4.1-10 mm bars without bar preparation up to 8 mm • Electrical control box • Motor voltage 400 V • Control voltage 24 VOptional: Comprehensive package of measuring instruments Technical Specification Counter Spindle Yes

Condition: ready for operation (used), Year of construction: 2003, bar diameter (max.): 10 mm, number of axes: 9, This TORNOS DECO 10a was manufactured in 2003. It features a movable headstock, directional spindle stop, and multiple cross-slides with tool holders for versatile machining. Equipped with a counter-spindle and programming software in five languages, it's ideal for complex turning tasks. Includes interfaces for bar feeders and tool breakage detection. Reach out for more information about this machine. Additional information • TB-DBCO Version 6 programming software: Single-user product, configuration available in 5 languages (French, German, English, Italian, Spanish) • Programming language: ISO programming language • Movable headstock: S1/Z1 axis, n = 16000 rpm, F13 collet chuck • Spindle stop: Directional spindle stop S1 (programming increment 0.1 degrees) • Cross-slides: • 1 cross-slide with 4 tool holders (X1 and Y1 axes) • 1 cross-slide with 3 tool holders (Z3 and X3 axes) • 1 cross-slide with horizontal and vertical movement (Z4 and X4 axes) • Pneumatic cylinders: 3 independent for quick positioning • Counter-spindle: Independent (S4), n = 12000 rpm, F13 collet chuck • Cross Slide Support Options: Ffodpfx Aaox D Dm Homsw • Pre-adjustable turning tool holder, long type, 8x8 mm cross-section • Main spindle rotation direction: right • S2 motorization (electric/mechanical) for driven units on the X2-Y2 linear tool carrier • Driven end drilling/milling unit: Max. speed 12000 rpm • Cross drilling/milling/tapping attachment for BSX 12 collet chuck • Sensor: Tool breakage detection with TYPE MIDI-DETECTOR, oscillating probe type MINI-DETECTOR, electrical interface, pneumatic control equipment • Interface: Adapting an LNS bar feeder • Spinde Speed: n = 16000 rpm indicates the machine has a moderate spindle speed ional: Comprehensive package of measuring instruments Technical Specification Counter Spindle Yes

Condition: ready for operation (used), Year of construction: 2000, spindle speed (max.): 12,000 rpm, bar diameter (max.): 10 mm, number of axes: 9, This TORNOS DECO 2000 swiss type turning machine was manufactured in 2000. It features a movable headstock, directional spindle stop, and cross slides with tool holders. Includes an independent counter spindle, lubrication device, and a loading magazine with drum. Equipped with a "HYBRIDE 10+5" drum for bars up to 10 mm and an integrated hydraulic unit. Contact us for more information about this machine. Additional information • Electrical control box • Motor voltage: 400 V Fjdsx D Dmyepfx Aamofw • Control voltage: 24 V • Movable headstock • Cross slide with 4 tool holders T11-T24 with vertical and horizontal movement • Pivoting workpiece holder on the counter spindle • Directional spindle stop S1 • 3 pre-settable turning tool holders • 4 fixed tool holders • "HYBRIDE 10+5" drum with 14 guide tubes for 1-4 mm bars and 14 guide tubes for 4.1-10 mm bars without bar preparation up to 8 mm • Independent counter spindle • Tapping attachment for collet chuck ESX 12 • Lubrication device for guide bushing with filter • Loading magazine with drum • Integrated 25-liter hydraulic unit with filter • Front/rear support foot, center height 1100 mmOptional: Comprehensive package of measuring instruments Technical Specification Counter Spindle Yes

Condition: ready for operation (used), Year of construction: 2007, bar diameter (max.): 10 mm, number of axes: 7, This TORNOS DECO 10e was manufactured in 2007. A Swiss type turning machine featuring a movable headstock, directional spindle stop, and multiple tool holders for versatile operations. Includes an independent counter spindle, lubrication device, and a loading magazine with drum. Ideal for precision turning with a lathe capacity of 10 mm. Consider the opportunity to buy this TORNOS DECO 10e Swiss type turning machine. Contact us for more information. 2 similar units available!Additional information • Movable headstock Ffedpfox D Dmmox Aamow • Directional spindle stop S1 • Cross slide with 4 tool holders T11-T24 with vertical and horizontal movement • Independent counter spindle • Pivoting workpiece holder on the counter spindle • Lubrication device for guide bush with filter • 3 pre-settable turning tool holders • Motorization S2 • Tapping attachment for collet chuck ESX 12 • 4 fixed tool holders • Loading magazine with drum • Integrated 25-liter hydraulic unit with filter • Front/rear support foot, center height 1100 mm • "HYBRIDE 10+5" drum with 14 guide tubes for 1-4 mm bars and 14 guide tubes for 4.1-10 mm bars without bar preparation up to 8 mm • Electrical control box • Motor voltage 400 V • Control voltage 24 V • Lathe capacity 10 mmOptional: Comprehensive package of measuring instruments Technical Specification Counter Spindle Yes

Condition: ready for operation (used), Year of construction: 2005, operating hours: 37,578 h, bar diameter (max.): 8 mm, number of axes: 9, This Tornos Deco 10 was manufactured in 2005. A swiss type turning machine featuring a drum with loading magazine, a filter with a 25-liter capacity, and an integrated hydraulic unit. It supports various bar diameters up to 8 mm, ensuring versatility for precision work. Consider the opportunity to buy this Tornos Deco 10 swiss type turning machine. Contact us for more information. • Drum with loading magazine • 10+5" HYBRID drum • Integrated hydraulic unit • Support leg rear/front • 1100 mm center height • Filter with 25 liter capacity • Electrical: 380 V, 3-phase, 50/60 Hz motor voltage • Control voltage: 24 V DC • Bar compatibility (for 14 guide tubes): • 1–4 mm diameter bars • 4 mm diameter bars Ffjdox D Dm Tepfx Aamsw • 8 mm diameter bars Additional equipment • 1 piece oil basin • 1 chip collecting basinOptional: Comprehensive package of measuring instruments Technical Specification Counter Spindle Yes