Laminating installation

Billhöfer FK102

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: 6878, working width: 1,020 mm, total width: 2,000 mm, total length: 12,000 mm, total height: 3,000 mm, stack height: 840 mm, Laminating machine FK 102 S in very good used condition Bdedoxb Dq Tjpfx Afpsa Sheet size min 30 x 45 cm Sheet size max 102 x 124 cm Feeder: Billhöfer A-20-P Smoothing calender: GK-4-1080 Sheet separator: Achilles BT 4.1 Stacker: Bremser S102A1 Additional equipment: pneumatic side lay by TPM electronic overlap control by PME automatic film brake by Achilles film cutting device by TPM spare roller (lamination counterpressure) new, included The machine can laminate using both water-based and thermal films (heating units required) Dismantling/transport/possible customs duties etc. must be organized by the buyer.

Condition: good (used), Year of construction: 2002, Format trimmed: max 300 x 400 mm, min 85 x 115 mm Untrimmed format: max 320 x 460 mm, min 100 x 125 mm Output: max 6,600 c/h Equipment: - Fully automatic infeed with integrated stack counter - Cut counter - Cutting blower - 1 set of pressing plates and holders - 1 set of plate tables - 3 sets of cutting bars - 2 sets of knives Bedpjqqkvqjfx Afpeda - External device for knife change with setting gauge - Central lubrication - Operating instructions - Electrical circuit diagrams - Standard tools - Standard accessories

Condition: used, Year of construction: 2014, functionality: fully functional, Coated web width 1315 mm Max. web width 1330 mm primary unwinder: 1000 mm secondary unwinder: 1200 mm rewinder: 1200 mm speed: 400 m/min Accessories: Bdsdpswp R Htsfx Afpoa - Solvent-less mixer Nordmeccanica - Continuous filling World Mixer (with 4 tanks of 200 kg) - 5 rolls Materials: COATED WEB BOPP 12 - 80 μ, PETP 10 - 30 μ, LDPE, LLDPE 30 - 200 μ, OPA 12 - 18 μ, NYLON CAST 30 - 80 μ ALU (Foil) 6,3 - 40 μ, PP CAST 60 - 150 μ, PAPER 40 - 150 gr/m2 LAMINATED WEB BOPP 12 - 80 μ, PETP 8 - 30 μ, LDPE, LLDPE 20 - 200 μ, OPA 12 - 18 μ, NYLON CAST 20 - 80 μ ALU (Foil) 6,3 - 40 μ, PP CAST 20 - 150 μ, COEX FILM 25 - 200 μ PAPER 40 - 150 gr/ m2

Condition: excellent (used), Year of construction: 1999, functionality: fully functional, Faster than the equivalent sliding-table press, the fixed-table Printmaster is perfect for medium and long production runs, delivering excellent quality results with virtually any material up to 4 mm thick. And because the machine prints incredibly fast, the Printmaster is undoubtedly the best on the market. Among its many sophisticated features is the patented dual gripper system that ensures perfect registration and quiet operation. The Printmaster can also be equipped with various optional systems and accessories that make it even more versatile, faster and easier to use. Integrated PLC control system. Independent LCD touch panel with setting and monitoring of printing parameters: - Job parameter storage system. - settings diagnostics. - Variable stroke lengths of scraper and flood coater. - Adjustable clamp, scraper and flood coater speeds. Motorized off-axis contact adjustment. Hardened, self-balancing stop points combined with "locking" fingers for material control. Bdjdpfeuptf Asx Afpsa Maintenance-free toothed belt drive for the scraper carriage. Double gripper bar shuttle system. Folding feed table. Fiber-optic registration control. Prepared for the addition of a feeder. High-strength steel lifting columns. Anodized aluminum work surface. Printing frame insertion. Multi-purpose self-adapting clamps. Pneumatic scraper pressure equalizer. Pneumatic scraper and flood coater changeover. Pneumatic clamping of printing frame and back bars. Horizontal flooding. Choice of flooding: immediate or delayed. Timer for machine stop to allow peeling action. Adjustable peeling at 6 levels. Adjustable blowing system. Foot pedal.

Condition: good (used), Year of construction: 2002, machine/vehicle number: 0102002, Semi-automatic angle opening Very good condition 3 months functional guarantee Print format: 1000 mm x 1500 mm max. sheet size: 1050 mm x 1550 mm max. screen frame: 1370 mm x 1850 mm Squeegee pre-squeegee height adjustment: 40 mm Squeegee angle adjustment stepless: + / - 50 - 90 ° Support bar height adjustment: 0 - 100 mm stepless Maximum material thickness: 100 mm Machine weight: approx. 1500 kg connected load: 400Volt/50HZ - 5KW Air connection: 6 bar options: pneumatic screen frame clamping Squeegee pressure compensation adjustable via pressure regulator Stainless steel pressure plate Blowing air device Bdedorllhkjpfx Afpea All data without guarantee

Condition: as good as new (ex-display), Year of construction: 2019, operating hours: 50 h, functionality: fully functional, machine/vehicle number: 19101105, roller width: 1,100 mm, Equipment: full service history, type plate available, The SDFM-1100 roll-to-roll laminator is a multifunctional laminating machine. It is designed for cold and hot laminating. The paper is laminated on one side with the foil. Then the web is re-rolled onto the roll. For cold laminating, the foil is coated with a water-based glue and dried using a heating roller with a warm air drying system. The winding system sends the paper to the laminating section, where the paper is covered with the foil by heating and roller pressure. The rollers use a heated water circulation system with constant temperature control. The paper roll is held by pins, which are controlled by a pneumatic brake. The paper is unrolled to the leveler, which is equipped with automatic leveling of the paper web before laminating, which ensures even coverage of the web with foil. In the laminator, the non-adhesive film is coated with a water-based adhesive and then dried with a heating cylinder or the film already coated with adhesive is unrolled into the laminating cylinder. The laminating cylinder is heated using induction heaters. Under the laminating cylinder, the paper is joined to the film using temperature and pressure generated by the lower rubber roller, which presses the film with the paper against the laminating cylinder. The laminated web is wound onto a core on a shaft in the receiving section, after which it can be transported to subsequent production processes. Specification SDFM-1100 Maximum roll width 1100 mm Maximum roll diameter 1100 mm Paper weight 80 - 500 g/m2 Film thickness 10-50 microns Working speed 10 - 65 m/min Electrical voltage 380V 50Hz Total power 78 kW Maximum power consumption 30 kW Bdodpjvy Aipofx Afpea Total weight 8000 kg Machine dimensions 10130×2130×2960 mm

Condition: good (used), Year of construction: 1997, functionality: fully functional, - Manufacturer: SPS - Model: Vitessa Star G2 - Machine type: screen printing machine - Year of manufacture: 1997 - Equipment: • Mabeg feeder, model MS • SPS dryer, type UV Top 1200, year 1993 • SPS Rehmus stacking unit, type Autostack S-02, year 1993 Bjdpfx Aoxby Smjfpsda • Steel platform and tread plate on pallets • Control cabinet • Screen printing frames - Area of application: industrial screen printing, packaging, labels, special applications

Condition: excellent (used), Year of construction: 2001, Jumbo roll Ø paper max. 1600 mm Jumbo roll width min. 560 mm Jumbo roll width max. 1400 mm Jumbo roll Ø PE, PET max. 1000 mm Expanding chucks Ø 76 mm, 100 mm, 150 mm, and 300 mm Bsdpfx Aexlkckofpjda Speed depending on material: 200 to 300 m/min. The Bielloni Castello Julia 2 SL laminating machine can process single-component PU adhesives with 100% solid content (solvent-free). The adhesive is applied via a sleeve system. Dispersion adhesives cannot be processed. The system does not feature a drying unit. The PU adhesive is applied to the paper web using heated rollers (approx. 70–90 °C). The bond between paperboard and film is achieved by pressure and subsequent self-curing. Paper grammage: 120 to 600 g/m², coated with PET min. 8 µm to max. 75 µm PE min. 20 µm to max. 75 µm The machine can be demonstrated in production.

Condition: used, Year of construction: 2000, TRESU Butler 1500 Flexographic Printing Press Manufacturer: TRESU (Denmark) Model: Butler 1500 Machine No.: 1090419 Year of manufacture: 2000 Maximum printing width: approx. 1500 mm Applications: printing on paper and other flexible packaging materials Typical use: production of paper bags, bakery packaging, fast-food, pastry, and other food products Configuration: flexographic press with multiple printing stations (exact number of colors available on request) Technical condition: fully operational, in production use, regularly maintained Supply voltage: 380V Bedexdi Atopfx Afpjda Advantages: Large printing width (1020 mm) suitable for a variety of packaging formats. Rugged construction, typical for TRESU equipment, known for reliability. Ideal for custom packaging printing on paper.

Condition: excellent (used), Year of construction: 2017, Ref: 11039 . 2017 Rollem 36” Jetslit + 30” Rollaway and Cassette AutoCollator Delivery High volume print finishing system to maximizes finishing productivity for large volume producers For greeting cards, photo books, direct mail, postcards, invoices, business cards, game cards and much more. Features: This flexible system takes full press sheets and converts them to finished products in one step, eliminating the need for guillotine cutting, excess manpower and paper movement. 100% accuracy of finished products is a key feature of the Jetslit. Performs multiple print finishing steps with one system Bi-directional slitting, cutting, creasing and perforating in one machine Ideal for high volume production Multiple-up layouts maximize press sheet Decreases excess labour costs Bodexyxttspfx Afpsda Eliminates touch points and paper movement Fully integrates with press via DFA communication system Accepts sheets in-line from press or operates in a stand-alone near-line configuration Process: The system takes full printed sheets with multiple images and converts each sheet in two directions, as shown below: 1. Full sheets are fed into the JetSlit registration guide for perfect alignment. 2. The sheets are completely slit on the extreme edges and timed slit in-between with Rollem's patented strike-slit feature. 3. The sheets are turned 90 degrees and re-registered. 4. Final slits are made, removing the notched portions and leaving the final pieces. Specification: Speed: Up to 6,000 cut product sheets per hour Format: Up to 36’’ (915mm)