Low loader semitrailer

DINKEL 4-Achs-Jumbotieflader - doppelte Rampen

Condition: used, maximum load weight: 44,980 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, first registration: 09/2024, next inspection (TÜV): 09/2025, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Chassis, bent * Special steel frame made of high-strength fine-grain steels, electrically welded at the joints, well-dimensioned outer frame * 4-axle arrangement. Wheel protection above the axles with spray mist suppression * All steel parts sandblasted * Lateral impact protection made of anodized aluminum mounted * Increased point load of approx. 30,000 kg over approx. 4,000 mm * Special design in the bent area for maximum low-bed length in combination with AluLeg outrigger supports instead of telescopic outrigger winches, max. rear swivel radius of the tractor unit approx. 2,100 mm Special superstructure with rear beam extension * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding tarpaulin with plastic flaps * Rear beams extendable to approx. 4,200 mm * Three sliding beams per side with rubber cord relief * Additional center beam locking in the roof beam and parking position, by means of a pull cable and spring latch * Lifting roof mechanically adjustable, lifting height approx. 400 mm, can be operated on both sides or on one side, without opening the opposite side and the doors * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the beams * Front overhang on the front wall for operation under tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, bottom 450 mm pockets, above 4 rows of single pockets * Only 3 rows of insert slats in the upper bed. Spacing between slats evenly distributed Floor * Approx. 27 mm special water-resistant glued beech plywood, rough surface Iiedpfolthguex Aqcog * Steel sheet in the wheel arch area * Forklift truck accessible according to DIN standard * Outer frame flush with the surface Brakes * WABCO compressed air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve) * Spring brake cylinders as parking brake * Wabco Smart Board with odometer and aggregate load indicator Axles * 4 x 10,000 kg SAF/Sauer with drum brakes in low-loader design * Air suspension with lifting and lowering device, total stroke approx. 230 mm * Third and fourth axles as friction-jointed trailing axles with electric and mechanical lock Twin tires * 235/75 R 17.5, -16-ply, incl. E-wheel holder. without E-wheel Paint finish * Chassis in RAL 3002 red, solid color * Center beams, axles coated with KTL black * Corner beams in hot-dip galvanized design * Plastic parts black * Hot-dip galvanized parts unpainted * Rims in factory silver * Superstructure in RAL color, solid color Special equipment incl. * Air suspension in ECAS design, operated on the semi-trailer * Overwidth signs front and rear in zinc-plated, steplessly telescopic design with attached warning lights including socket for rotating beacons (small panels) * Sliding tarpaulin cover locking additionally from the outside * 4 beam adapters for special outer frame profile, to lock the center beams as desired * PVC sliding tarpaulin, color similar: RAL 9006 silver * Roof tarpaulin translucent, in overwidth and overheight design, flat hooks, tarpaulin folds, closures with pawl lock /OCS * Telescopic socket for rotating beacon including beacon on the rear left * Outer frame for machine transport with app

Condition: new, maximum load weight: 45,250 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete inventory of vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Full specifications available upon request. Chassis, stepped: * Special steel frame made from high-strength fine-grained steels, electrically welded at connection points * Generously dimensioned outer frame. 4-axle configuration * Wheel covers over the axles with spray suppression * All steel parts sandblasted * Side underrun protection made of anodized aluminum mounted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area for the longest possible low-bed length in combination with AluLeg drop supports instead of telescopic support legs, maximum rear swing clearance of the tractor unit approx. 2,100 mm Special body with rear stake extension: Iiodpfjwx Dbisx Aqceg * DINKEL – special body * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable for loading/unloading up to approx. 4,200 mm * Three sliding stakes per side with elastic relief * Additional intermediate stake lockings in roof beam and parked position, via pull cable and spring bolt * DINKEL – mechanical lift roof, height-adjustable * Lift roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments by adjusting the stakes * Front cover at bulkhead for driving operation under the tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, 450 pockets below, four rows of single pockets above. Only three rows of slats in the raised platform, spacings evenly distributed Floor: * Approx. 27 mm special waterproof bonded beech phenolic plywood, rough surface * Steel sheet in the wheel well area. Suitable for forklift traffic as per DIN standard * Outer frame flush with deck surface Brakes: * WABCO air brake system with EBS according to EC Directive 71/320, including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with mileage counter and axle load display * Including WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF with drum brakes in low-loader design * Air suspension with lift and lower device, total lift approx. 230 mm * Third and fourth axles as friction-steered trailing axles with electric and mechanical lock Twin tires: * 235/75 R 17.5, 16-ply. Make of our choice, including spare wheel holder * Without spare wheel Lighting: * According to EU regulations, including LED side marker lights * Position lamps in LED design * 2 additional reversing lights * 2 work lights on the inside front wall, upper section Paintwork: * Chassis and body in one color, RAL 3002 carmine red * Intermediate stakes, axles KTL-coated black * Corner stakes hot-dip galvanized * Plastic parts black * Galvanized parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply cable * Air suspension in ECAS design, operated on the trailer * Oversize signage front and rear in galvanized, infinitely telescopic design with installed marker lights, including sockets for rotating beacons (small signs) * Additional external release for sliding roof frame lock * 4 stake adapters for special outer frame profile, to lock intermediate stakes as needed * PVC sliding tarpaulin, color similar to RAL 9