EPS Cutting line with packing machine

ERLENBACH ESA 5

Condition: good (used), Year of construction: 2008, HAAS VF-5D / 40 MACHINING CENTER TRAVELS : X : 1,270 mm Y : 660 mm Z : 635 mm Hfjdpfjvf Nw Dox Ad Hsf DISTANCE BETWEEN PLANE – TABLE AND SPINDLE NOSE : 178 – 813 mm TABLE : DIMENSIONS : 1,321 x 584 mm LOAD CAPACITY : 1,815 mm NUMBER AND SIZE X PITCH OF T-SLOTTS : 7.14 X 80 mm SPINDLE : ROTATIONAL SPEED : 8,000 RPM SPEED RANGES : 2 SPINDLE NOSE : ISO 40 HIGH PRESSURE / INTERNAL COOLANT FEEDS : RAPID SPEED : 18,000 mm / min. WORKING SPEED : 12,700 mm / min. JOG : 0 – 1,260 mm / min. TOOL MAGAZINE : 24 POSITIONS POWER : 15 KW WEIGHT : KG. 7,000 YEAR OF FIRST INSTALLATION : 2008

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Hedpfjwp Rqfex Ad Hjff Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: good (used), Loypack One shot chocolate depositor Stainless one shot moulding machine, 100Kg twin hopper, moulds are loaded into a denester, adjustable temp control, variable speed, heated water tank, comes with over 300 different moulds for making neopolitans, 3Ph Hfedpfsmqm E Uex Ad Hof

Condition: used, Year of construction: 2006, functionality: fully functional, color channels: 5, paper weight (min.): 40 g/m², paper weight (max.): 370 g/m², paper width (min.): 400 mm, paper width (max.): 800 mm, paper height (min.): 260 mm, paper height (max.): 600 mm, input voltage: 380 V, Sakurai OL575SD - 5 Colors + Coater Year: 2006 Impressions: 50,000 Max Sheet Size: 60x80 cm Double development cylinders Hfsdjwtzp Topfx Ad Hsf Detachable grinding from unused printing units Printing speed: 15,000 sheets/hour SPC - Sakurai Plate Changing SAS - Sakurai Auto Set SCC III - Sakurai Colour Console - Type 3 Automatic washing Cloth blanket washing device IR Dryer (Grafix) Chambered doctor blade anilox coater

Condition: excellent (used), Year of construction: 2016, Inca Onset X2, 3/4 automized Color configuration: 8 channel printer with four colours (CMYK) 1/12th of the new price !!!!! Printhead status allowing to print at maximum speed with outstanding quality, up to 140 beds per hour/700m² per hour, needs replacement of 60 heads (circa 45.000€) Hedpfx Ajun Swbjd Hoff The machine is in excellent shape, serviced by manufacturer since day number one. Annual maintenance done in May 2025. Available: January 2026 As the business expands, Onset X2 provides the capacity to extend the range of jobs companies can handle. The addition of a second set of CMYK delivers even higher productivity - up to 707m²/hr* (equivalent to 138 full-bed sheets/hr) - while an optional six channels can be populated with light cyan (Lc), light magenta (Lm), white (W) and orange (O) to add versatility and superb quality. A choice of uni-directional, bi-directional and super high-quality print modes can be selected depending on the specific job requirements. * Based on an approximate 6 second material handling time. Decomissioning, transport, installation, training and warranty are included (in Europe) For further technical details please refer to enclosed data sheet.

Condition: used, machine/vehicle number: 007716, X axis working area: 3250 mm Hedpfxswuz N Ns Ad Hsff Y axis working area: 1220 mm Working Table: Pod and Rail Main Electrospindle power: 12 KW Number of controlled axes: 4 axes Total number of drilling spindles: 18 Total number of tool changer positions: 16

Condition: used, Technical details: wire diameter - max.: 9,0 mm wire diameter - min.: 2,0 mm voltage: 380 V / 50 Hz V control voltage: 220 V Total power requirement: 18 kW Weight approx.: 5,0 t dimensions: Schmiermittelanlage: 830 x 650 x 1000 mm dimension machine xH: 3,3 x 1,5 x 1,45 m dimensions electric cabinet LxWxH: 0,7 x 1,5 x 1,75 m WIRING AND CUTTING MACHINE / MACHINE WAS UPGRADED WITH A NEW CONTROL SYSTEM IN 2000 A programmable, electronically-hydraulically controlled universal spring coiling machine for the production of right and left-hand tension and compression springs as well as torsion springs. The springs can be produced with any pitch and shape of spring body. Output max. 90 pieces/min. Outer spring Ø 10 - 120 mm Unlimited wire feed length, speed = 27 - 80 m/min. Coiling device: two-finger system wire thickness Ø 2.0 - 9.0 mm; spring outer Ø Ø 10 - 120 mm Single-finger system: wire thickness Ø 3.0 - 7.0 mm; spring outer Ø max. Ø 60 mm Equipment: 5x feed rollers, wire holder 3 mm two-finger Hjdpfx Aevc Aklod Hsff Spring length measuring device LION PRECISION-PANTHER Wire roller holder POST, motor-driven, mandrel holder Ø 1,400 mm Lubrication system Control cabinet cooler RITA Hydraulic unit Optional many accessories and/or spare parts! i.D. *

Condition: good (used), Year of construction: 1995, machine/vehicle number: 0540/98, functionality: fully functional, Manufacturing number: 0540/98. Year of manufacture: 1998 ,. Hfodeicbbzopfx Ad Hjf Capacity: 400 tons. Stroke length: 300 mm. Stroke: 10-40 / min. Slide adjustment 300 mm. Installation height: 700 mm. The table measures 1600 x 1300 mm Net weight: 45 tons. Gable opening: 1600 mm. Exterior dimensions 2 x 3 x 6 meters. Control system MEAB. Coil feeder / straightener iRON RNE 50B / 11. Decoiler iRON SA6000 max 700 mm.

Condition: excellent (used), Year of construction: 2004, year of last overhaul: 2004, 4-Hi CRM Rolling Mill Head Froehling Froehling is a renowned brand recognized for reliability and robustness in the field of rolling mills. 4Hi rolling mill head with bending and coilers. Specifications: Manufacturer: FROEHLING (Germany) – Refurbished 2004 Hsdpjg Ryqksfx Ad Hoff Processable material: Aluminum alloys – brass – copper – low carbon steel Strip width: 282mm (300mm) Strip thickness: 0.15 - 2mm Coil size: ID 400mm – OD 1500mm Max. rolling speed: 400m/min Work rolls: Diameter 130mm – Table 340mm Back-up rolls: Diameter 390mm – Table 335mm Complete with: Uncoiler and recoiler Many sets of spare work rolls and back-up rolls Sold EXWORKS, dismantled and loaded on truck. Ready for inspection by any interested buyer. For any questions, do not hesitate to contact us. PLEASE SUBMIT YOUR OFFER IF INTERESTED, WE WILL SURELY REACH AN AGREEMENT TOGETHER.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Hsdofz U S Eepfx Ad Heff Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.