Belt Grinding Machine

FALKEN // SAHINLER BT 114 S

Condition: refurbished (used), functionality: fully functional, Löser centerless tube grinding machine - belt grinding machine - polishing machine - Cylindrical grinding machine Centerless tube grinding / polishing machine for workpieces with a minimum length of 1100mm. The machine was built in 1988 and was completely overhauled in 2012. The machine was converted for polishing and then only polished around 10,000 parts. The machine was no longer used after that. During the general overhaul, the motors, bearings and the entire control cabinet with the frequency converters were completely replaced. The machine can be used for both wet grinding and polishing. Wastewater treatment including pumps is not yet available. We can retrofit these for you free of charge according to customer requirements. The transport systems (roller conveyors) between the grinding stations must also be retrofitted to suit your workpieces. The machine can process pipe diameters from 10mm to 160mm. The grinding motors / polishing motors have an output of 7,5kW per station. The system can be viewed by appointment in our warehouse in D-63128 Dietzenbach. Godpfxopugwio Ad Heua

Year of construction: 1987, condition: ready for operation (used), An old Schumag Aachen drawing machine without control is available. Drawing force: 100kN, drawing speed: 80m/min, material diameter range: 25mm-43mm. On-site inspection is possible. Godpfx Aov Tctuod Hsua

Condition: refurbished (used), functionality: fully functional, Löser centerless tube grinding machine - belt grinding machine - polishing machine - Cylindrical grinding machine Centerless tube grinding / polishing machine for workpieces with a minimum length of 1100mm. The machine was built in 1988 and was completely overhauled in 2012. The machine was converted for polishing and then only polished around 10,000 parts. The machine was no longer used after that. During the general overhaul, the motors, bearings and the entire control cabinet with the frequency converters were completely replaced. The machine can be used for both wet grinding and polishing. Wastewater treatment including pumps is not yet available. We can retrofit these for you according to customer requirements. The transport systems (roller conveyors) between the grinding stations must also be retrofitted to suit your workpieces. The machine can process pipe diameters from 10mm to 160mm. The grinding motors / polishing motors have an output of 7,5kW per station. Godpfetmqi Dex Ad Hsua The system can be viewed by appointment in our warehouse in D-63128 Dietzenbach.

Condition: good (used), Year of construction: 2011, functionality: fully functional, section length (min.): 100 mm, section length (max.): 3,500 mm, type of input current: three-phase, For sale: Used WAFIOS RS4 wire straightening machine in good condition. Technical data: • Model: RS4 • Manufacturer: WAFIOS • Straightening range: 3 to 6 mm • Equipment: includes blade, straightening stones, feed rollers in various sizes, decoiler Gsdpfsw U Eubjx Ad Hjua • Year of manufacture: 2011 Condition: • Fully functional, regularly serviced Location: 74931 Lobbach Price: €9,900 net

Condition: good (used), Straightening machine, wire straightening machine, unwinder, straightening machine combination, pay-off reel, wire unwinder, double reel, reel, pay-off reel, motor-driven reel for wire processing, punch, eccentric press, hydraulic press, punching machine, motor reel, winding roll, unwinder, wire unwinder Gusdpfxoin Rn Ae Ad Hsa -Wire straightening machine: decoiler-straightener combination -Type:not visible -Note: without documentation -Engine: Fukota 1.5 kW -Straightening rollers: for Ø 20 mm, see photos -Receiving rollers: Ø 152/215 x 1330 mm -Total dimensions: 3040/2450/H2525 mm -Weight: 2080 kg

Condition: used, Year of construction: 1972, functionality: fully functional, machine/vehicle number: D08U/8378, Offer Number: D08U/8378 Machinetype: straightening and cutting machine Info: flying shears Make: WAFIOS Type: RF6 Constr. year: 1972 diameter range: 8-16 mm cutting length: 520-6000 mm Gusdpfx Aew Nhv Djd Hea speed - meters/min: 25-75 diameter range: 8-14 mm Location: Outside of Europe

Year of construction: 2003, condition: good (used), functionality: fully functional, machine/vehicle number: 03234, 6 Brush ( 3 pairs) descaling machine for steel wire size 5.5mm - 16.0 mm max (low carbon) Brush pairs arranged in a 60 degree offset for maximum effect. Gedpfx Adox R Uzde Hsua A very clean looking machine. On site viewing and inspection recommended

Condition: used, Straightener & polishing machine WRPT2, manufactured by KIESERLING Gsdpsymcm Esfx Ad Hjua Bars diameter : 10 - 35 mm Bars length : 3 - 6 m Scope of delivery includes : 1. Infeed pinch-roll with - Motorised bottom roller - Vulkollan upper roller 2. WRPT2 straightening machines, made KIESERLING with - 2-roller straightener with upper roller height adjustment and upper/lower angle adjustment - Two geared motors with cardan shaft drive - Infeed guide - Side guide support - 1 set of side guides 3. Outfeed pinch-roll with - Motorised bottom roller - Vulkollan upper roller 4 Electric control panel with manual movement buttons Bars diameter: 10 - 35 mm Bars length: 3 - 6 m

Condition: ready for operation (used), functionality: fully functional, DESCRIPTION OF MACHINE INCLUDED A LOT BELTS A Löser abrasive belt grinding machine offers the most flexible grinding / linishing on the market today. The combination of basic machine plus a variety of contact arms and attachments offers dozens of possible applications for many different purposes. There are over 20 standard attachments available for this machine allowing it to be used for centerless grinding, internal polishing, grinding of hollow bodies and small radius and turbine blade finishing to name but a few. Fields of application of these abrasive belt grinding machines include: *Foundries Godpfx Adswxrnwe Hjua *Medical engineering *Aircraft industry *Vehicle construction *Mechanical engineering *Specifications Abrasive belt grinding machine, type KS 350 *Grinding belt length 3000-4000 mm *Grinding belt width 5 - 75 mm Loser KS 350 Belt design features:: *Drive motor 4 kW (standard design) with fitted variable speed inverter drive *Drive wheels of 100 - 280 mm diameters = 3 - 46 mtr./sec. belt speed *Mechanical belt tensioning *In case of a belt break the drive is immediately disconnected. Therefore, the risk of an accident is eliminated. *Contact disks of 50 - 400 mm diameters, with a wide choice of grinding attachments for any kind of surface finishing * DC injection breaking unit fitted. *Maintenance-free, dust-proof contact disk bearing with permanent lubrication, contact disk change in less than 1 minute. *LÖSER abrasive belt grinding machines open up new fields of application for belt linishers that in the past could not be processed with normal belt grinders. *When using 3 to 4 m long grinding belts, the 3-contact wheel system ensures the constant and optimal belt speed no matter which contact disk diameter is being used. *Driven by the motor pully, the three pully system allows the belt which is constantly tensioned a higher degree of torque at the same motor rating. *When working with Scoth-Brite disks or belts or with felt polishing belts, the drive can be infinitely adjusted even for speeds as low as 3 mtr. /sec. Due to the advantages offered by the 3-contact point system, any required surface finishing is possible using contact disks from 50 to 400 mm, contact rolls or contact rollers from 15 to 50 mm, contact belts of 6 or 30 mm width, polishing brushes, polishing disks and polishing belts.