Low loader semitrailer

FAYMONVILLE Multimax Satteltieflader (2+2) - nachlaufgelenkt

Condition: used, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 03/2025, next inspection (TÜV): 08/2027, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. GOOSENECK * Designed in SNT for optimized loading area length * Length approx. 3,700 mm, with a rear slope of approx. 1,000 mm x 10°. For SZM: 4 x 2, 6 x 2, and 6 x 4. * Front panel made of steel, plug-in type, approx. 400 mm high * ASPÖCK-UNIBOX on the connection strip at the front with sockets * 3 kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches * Without installation of the supply connections on the SZM * Outriggers on the gooseneck with mounting holes for screw-on lashing rings * The first hole is approx. 200 mm from the front, followed by one every approx. 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings in the rear area of the gooseneck (LC 10,000 daN) * Approx. 40 mm thick hardwood deck above the gooseneck * 2-inch kingpin * Guide plate on the gooseneck for the turntable, approx. 500 mm wide * 1 pair of recessed bolster pockets on the gooseneck for plug-in bolsters, approx. 100 x 50 mm LOADING AREA * In an extendable design, length approx. 8,800 mm with a slope at the rear of approx. 500 mm x 10°. * A recess in the loading area and extending into the slope for accommodating the excavator arm, approx. 2,490 x 750 x 210/290 mm (L x W x H). * TPMS tire pressure monitoring system according to ECE R 141. * Mechanical landing gear with 2-speed gearbox and crank. JOST Module B * Static test load = approx. 50,000 kg * Continuous hardwood deck, approx. 50 mm thick, on the loading area and interrupted between the axles (this increases the coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with a large cross-section. Dwsdpszz Ei Refx Akmjc * 1 pair of fixed wheel recesses in front of the axles, open to the cross member of the gooseneck, approx. 700 x 410 mm (W x D) * Wheel recesses with square ladder strips approx. 15 x 15 mm and widening in the lower area - 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the loading area between the 1st and 2nd axles. Wheel recesses with square ladder strips approx. 15 x 15 mm and widening in the lower area * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axles, which can also be used as widening boards (if the vehicle is equipped with extendable wideners) * 1st axle with starting aid BPW axles and suspension * 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock via reverse gear and can be activated manually * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve. * 235/75 R 17.5 3PMSF twin tires. Manufacturer of our choice HYDRAULIC LOADING RAMPS * DR-15/60-900-4350-HB-HV-M * A pair of two-piece steel ramps * with a length of approx. 4,350 mm and a width of approx. 900 mm. Hardwood deck * Hydraulically folding ramp tips. Ramps can be individually shifted hydraulically outwards by approx. 235 mm and inwards by approx. 215 mm * Maximum load and angle of inclination according to the technical data sheet: C465497 * In accordance with Regulation 2021/535/EU, ramps with a length of less than 300 mm do not need to be taken into account in the vehicle length of 16,500 mm in the driving position. * Hardwood deck on the slope of the loadin

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electro-hydraulic power unit for hydraulic functions, excluding hydraulic winches Dwsdpfx Ajy Auh Iskmsc * Approx. 40 mm thick hardwood decking above the gooseneck * 2-inch kingpin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Bracket at the rear of the gooseneck for ALU loading ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the front wall * 1 pair of stake pockets recessed on the gooseneck for plug-in stakes approx. 100 x 50 mm (located on the inside of the chassis rail) EQUIPMENT: * Loading platform length approx. 8,800 mm, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * A recess in the loading platform, extending into the tapered section to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adapt to the selected loading platform length * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: each 12,000 kg with air suspension and raise/lower valve * 235/75 R 17.5 3PMSF twin tires. Manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Module B – static test load = approx. 50,000 kg * Throughout the loading platform and between the axles, interrupted approx. 50 mm thick hardwood decking (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the telescopic tube with large cross-section. Intermediate table with offset loading platform and extendable mounting rails for aluminum bridging elements * Platform locking with conically welded locking profiles every approx. 250 mm. Includes pre-tensioning plate * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck cross member, approx. 700 x 410 mm (W x D) * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom (in case vehicle is equipped with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the platform between 1st and 2nd axle * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, which can also be used as widening planks (if vehicle is equipped with extendable widenings) * Lockable aluminum elements installed on the extension tubes of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasting painted...