Turning machine - cycle control

GILDEMEISTER NEF Plus 500

Condition: used, Year of construction: 1999, turning diameter 500 mm turning length 1500 mm control Manual Plus spindle bore diameter 70 mm turning speed range 8 - 2800 U/min transmission ratio 3 swing diameter over face slide 290 mm spindle head DIN 55027 Gr 8 tool holder Typ C quill stroke 180 mm weight of the machine ca. 3,2 t dimensions 3,0 x 1,8 x 1,8 m Description of the machine: This machine is suitable for turning chucked and shaft workpieces. The commercially available steel grades, casting, copper, aluminium, brass, Fpedpfx Asub Amlsa Nsp gunmetal and cuttable plastic can be turned on this machine. --> Concept of the N.E.F. plus The machine si supplied as standard with the following described equipment - Cycle control - AC-Main drive - Compund slide rest with AC drive and operating panel - Tailstock traversable using slavingunit, manualy clamped, including following centre point - Coolant unti - Chip protection hoods, manually actuated - Protection hood for chuck - Fast change tool holder Hahn & Kolb Multifix C - Reduction collar for turning spindel accessories according to pictures: - 2 STK steady rests - various clamping jaws - Hahn & Kolb Multifix type C - Various torsion bar holders Technical data: Working area: - Circulation diameter over bed: 500 mm - Circumferential diameter above the radial slide: 285 mm - Chuck Ø: 250(315) mm - Face slide: 260 mm - Distance between centres: 1000/1500 mm Turning spindle: - Spindle head DIN 55027: Size 8 - Hole diameter of the spindle: 70 mm - Hollow taper of the spindle nose: 80 metric - Spindle diameter in front bearing

Condition: like new (used), functionality: fully functional, Weiler Commodor guide and feed spindle lathe with 3-axis digital display K&C NEW Overhauled with acceptance certificate for tolerances of new machines Technical data: >> Machine no. 1824 >> Center height 180 mm >> Center width 1000 mm >> Spindle speeds: from 13 to 2000 rpm >> Spindle passage 56 mm >> Short taper spindle head DIN 55029 size 5 >> Tailstock MK 4 >> Feed rates from 0.026 to 0.888 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.35 to 12 mm >> Weight approx. 1500 kg >> Spindle brake can be switched on >> Drive power 2.0/4.0 KW >> Length 2.2 m, height 1.5 m, depth 1 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving of the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching of the counting direction, Fpodpfjvrcqdox Aa Nop >> Three-jaw chuck wedge bars as good as new 200mm 1 set of jaws >> Mulifix size B with 2 pcs steel holders NEW >> Bed stop >> Machine feet >> Coolant system >> LED machine lamp For safety, the machine is equipped with: >> Electronic spindle protection >> Spindle brake >> 2 emergency stops On request: covers for the guide. and feed spindle About the machine: A Weiler Commodor guide and feed spindle lathe is offered in a geometrically overhauled condition. The guides have been reground or re-scraped. With acceptance according to the test report. 2K glossy white paint. The Multifix and chuck accessories are new. For safety: The machine has a brake motor, electronic spindle protection and two emergency stops - an absolutely new lathe. Even at high speeds, the Weiler runs very quietly. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: used, Lathe Gildemeister Nef plus 500, year of manufacture 1996. Dimensions are approximately 3 m long, 1.70 m high, 1.5 m deep. Fpedpfew E D Txox Aa Nep

Condition: used, Lathe Gildemeister Nef plus 500, year of manufacture 1996. Dimensions are approximately 3 m long, 1.70 m high, 1.5 m deep. Fedpfxoxurd Uo Aa Nepp

Condition: excellent (used), Year of construction: 1994, Manual Plus control unit Turning diameter 260 mm Swing diameter 475 mm Center distance 1000 mm Turning length 880 mm Spindle speed 3,000 min-1 4-fold parat holder Tailstock Fpsdjt T T Uxspfx Aa Nop

Condition: used, Year of construction: 2001, turning diameter 500 mm turning length 1000 mm control MONFORTS CONTROL control SYSTEM MTC-K turning diameter over bed slide 290 mm spindle bore 70 mm spindle turning speed range 3 - 2800 U/min spindle power 15 kW max. torque on the spindle 1530 Nm spindle head DIN 55027 Gr. 8 feed power X/Z axis 11300 N Fjdpfx Aaovh I Hve Nspp rapid travel - longitudinal/face 10 / 5 m/min bed width 360 mm travel of cross-slide 265 mm upper slide travel 140 mm turning tool - shaft cross cut 32 x 25 mm tailstock quill diameter 80 mm tailstock quill stroke 160 mm tailstock taper MT 5 weight of the machine ca. 3,1 t dimensions of machine L x W x H 2,88 x 1,68 x 2,18 m Accessories: 3-jaw chuck ROTA-S plus 250 mmø, 4 pos. toolholder PARAT, coolant

Condition: used, Year of construction: 2000, turning diameter 500 mm turning length 1500 mm control MONFORTS CONTROL control SYSTEM EURO TURN turning diameter over bed slide 290 mm spindle bore 70 mm Fjdpfx Aasvh Ncre Nopp spindle turning speed range 3 - 2800 U/min spindle power 15 kW max. torque on the spindle 1530 Nm spindle head DIN 55027 Gr. 8 feed power X/Z axis 11300 N rapid travel - longitudinal/face 10 / 5 m/min bed width 360 mm travel of cross-slide 265 mm upper slide travel 140 mm turning tool - shaft cross cut 32 x 25 mm tailstock quill diameter 80 mm tailstock quill stroke 160 mm tailstock taper MT 5 total power requirement kW weight of the machine ca. 3,3 t dimensions of machine L x W x H 3,45 x 1,65 x 1,93 m Accessories: 3-jaw chuck ROTA-S plus 250 mmø, 4 pos. toolholder PARAT, coolant